8 best utilitech sump pumps

Product description

CDT50 is a submersible cast iron and coated steel sump pump with tether float switch. For use in 14" diameter or larger sump basins; 13" on level and 7" off level.

From the Manufacturer

1/2 HP Cast Iron Sump Pump with Tether Float Switch. Intended for indoor use only.

• Assembled in the US with foreign and domestic parts.
• Top suction pump design eliminates air locks and clogging from debris in bottom of sump pit
• Epoxy-coated steel motor housing and rugged, cast iron pump base
• Fully submersible
• 1/2 hp; max. Flow rate is 4200 gallons per hour; 3150 gph at 10 ft. Of discharge lift
• 1-1/2" npt discharge
• Assembled in the US with foreign and domestic parts.

User questions & answers

Question:	what is the amp rating & 10ft hour gallons
Answer:	1.Take out filter sponge from the pump. 2.Remove the cover of the pump. 3.Remove the second plastic shell and you will find an impeller 4.Check if there are blockage and clean the impeller 5.Install all the accessories for the pump.
Question:	is tether float adjustable
Answer:	1. If you use the suction cups on the bottom to the middle of your water bath it should be fine for any water flow. 2. The round solar fountain pump also come with a net bag, you can put some stones into it to prevent the fountain moved freely. 3.You can change the nozzle to ensure the solar fountain can spray more lower, so that you not worried about the water was emptied.
Question:	How long is the power cord
Answer:	The solar pump has suction cups on the bottom, so if the water in your container isn't too deep, you could stick it to the bottom. But if the container isn't too wide across, you can put some stone into the net bag and fix the bag, it will keep the fountain pump for stable.
Question:	What is the noise level
Answer:	Six. The six different spray patterns are nice, you can change the nozzles what you like.

Product features

WAYNE CDT50 Cast Iron Submersible Sump Pump With Tether Float

The WAYNE 1/2 HP CDT50 is a Submersible Cast Iron and Coated Steel Sump Pump with Tether Float Switch. The durable cast iron housing offers reliable operation and makes this the perfect pump for basement operations.

Sump Pumps/Battery Back-Up Pumps

The most common water pump. Sump pumps are automatic pumps used to remove ground water from sump pits and transfer basement drainage to prevent residential flooding.

Battery Back-Up Sump Pumps are added in addition to your primary sump, and are powered off a 12 volt battery. This completes your sump pump system and provides additional protection to remove ground water during a power outage, primary pump failure, or heavy rain.

Sewage Pumps

Sewage Pumps are automatic pumps used in heavy duty applications. Common applications include pumping waste from a bathroom to a sewer or septic line is a common application.

Utility Pumps

Utility pumps are multi-purpose pumps. Uses range from everyday applications around your home, to occasional use. Typical applications include removing standing water off basement floors or construction sites, draining aquariums and water beds.

Well Pumps

Well pumps are used to deliver water from an underground water source to your home, however, they are not submersible and are usually placed outside the well in a well housing. Well pumps can pump water from wells up to 25 feet deep. Well pumps can also be used as booster pumps.

Product description

Remove ground water from your sump basin and prevent flooding in your basement with this Utilitech 0.5 HP submersible sump pump. Its high capacity flow pumps up to 4,200 GPH, and the non-clog thermoplastic impeller design passes 1/2 in diameter stringy material, preventing waste build up. The vertical float rides up and down, turning the pump on and off, resulting in automatic operation. The heavy duty cast iron construction ensures strength and long pump life, and the 8-ft. cord provides accessibility from different pit and basement locations. A manual is included, offering easy operation for this Utilitech sump pump.

• Brand New in box. The product ships with all relevant accessories

User questions & answers

Question:	Does it come with a discharge hose and if not where can i get one that is
Answer:	When the nozzle is removed, the water column sprayed out of the product becomes a (short and thick) shape. You no worried it will hurt you .

Product description

Superior Pump builds pumps that are truly Built to Last and are 100 percent factory tested. Superior Pump uses quality components including solid copper motor windings, heavy duty stainless steel jacketed shaft seals, double o-ring seals on motor plate, and electronically controlled split capacitors. Superior Pump model 91570, 1/2 HP thermoplastic submersible utility pump with 10 foot power cord and ¾-inch garden hose adapter, will move water up to 3300 gallons per hour. Equipped with suction screen to filter out large debris and handles up to 3/8-inch solids with ease. This pump is UL/CUL listed and CSA certified and backed by a 3 year warranty.

From the Manufacturer

Superior Pump is a family owned and operated Pump Company specializing in residential / light commercial duty pumps. Headquartered in Minneapolis, Minnesota, Superior Pump was founded in 1999 after spending years in the pump industry dating back to the 70's, and with a plumbing background starting in St Paul Minnesota dating all the way back to 1885. Superior Pump adheres to our strong core family values, selling the absolute highest quality product possible. Known for building durable pumps, Superior Pump concentrates on quality throughout the engineering, manufacturing and testing processes. Quality products, strong warranties, excellent USA based customer service - Superior Pumps Built to Last!

• 1/2 HP Utility pump moves up to 3,300 gallons per hour; pump will lift water up to 25' of vertical height
• Tough thermoplastic construction; 10' cord length
• 1-1/2 inch NPT discharge for high capacity pumping; includes 3/4 inch garden hose adapter; Amps:4.9
• Removable suction screen and handles up to 3/8 inch solids
• Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested

User questions & answers

Question:	What's the PSI or max head (pumping vertical height) of this pump
Answer:	Length of hose for a sump pump is not nearly as important as lift. you can have a long horizontal run with only minor flow loss. Friction loss (the loss from hose length) at these low pressures is very small. The elevation (aka lift) is the true limiting factor. (PSI means pounds per square inch, FYI, the water pressure coming into your house from the main is about 50-80psi, someone wondered what psi meant). Based on the chart, this pump moves about 30 gallons per minute (gpm). If you lift ten feet the flow drops to about 20 gpm; at 20 feet of lift it's flowing about 10 gpm. I have used this with vinegar to flush my tankless water heater and I used it with about 50/50 mix of simple green and water in a 5 gallon bucket as a parts washer for motorcycle parts and the pump is fine. I do flush it with clean water when I am done.
Question:	Does it have an automatic shut off
Answer:	The pump does not have an automatic shut off. I added a float switch because I wanted it to pump out a sink that had a slow-running clogged drain where I had the washing machine. When the sink was mostly pumped out the float switch turned off the pump. It worked great for a couple years until I got around to dealing with snaking the drain which didn't have an easy clean-out. This is a good pump, since the sink drain got taken care of, we've been using the pump to pump koi pond water over a 5' fence to our neighbor's garden using about 150' of garden hose. The pump runs continuously for 5+ hours without issues in this process.
Question:	Will clothes washer hoses fit on this pump
Answer:	The pump itself fits a garden hose nicely. You can buy the attachment package listed next to it for the converter piece. It only came to around $8.00. It also comes with a larger hose. I didn't need it for my spa but if you need to empty a washer or bigger pool it seems like it would come in handy. Hope that helps. Good luck. :-)
Question:	Can this be user to flush a tankless heater with vinigar
Answer:	I bought the pump for this very reason. I'm not sure if it is rated to handle vinegar, but at the price I figured I'd try it and see. I have two tankless water heaters, and I wanted a pump that could clean out both at the same time and this pump certainly does the job. I have a hose that runs from the pump, into a splitter. From the splitter I have two hoses going to each water heater (one hose per water heater). Even pushing water through two hoses, it still has a strong flow, with each hose pushing about the same flow as the water hose faucet outside your house opened wide open (guestimate). The splitter I have allows me to adjust the flow rate by closing off some valves if it is too strong. For just one water heater, i would think this pump is too strong (as it REALLY moves water), but I'm not a plumber so I couldn't say for sure. If I were to do it again, I think I would have purchased the 1/4 HP pump, or even the 1/5HP for cleaning out water heaters with vinegar. I cleaned out my water heater this week for the first time using this pump. I let it run for 2 hrs, and I noticed that it got warm (about the temp of a warm-to-hot bath). I'm not sure if that is normal, but thought I'd let you know.

Product features

Superior Pump 91570 1/2 HP Thermoplastic Utility Pump

Superior Pump builds pumps that are truly Built to Last. Superior Pump uses quality components including solid copper motor windings, heavy duty stainless steel jacketed shaft seals, double o-ring seals on motor plate, and electronically controlled split capacitors. Superior Pump model 91570, 1/2 HP thermoplastic submersible utility pump will move water up to 3300 gallons per hour. Equipped with suction screen to filter out large debris and handles up to 3/8 inch solids with ease. This pump is UL/CUL listed (E238091, by UL, 2019) and CSA certified (230584, by CSA, 2019)

Construction and Discharge

• Thermoplastic construction is corrosion resistant and offers years of performance and reliability.
• 1-1/2 in. NPT discharge.
• 3/4 in. Garden hose adapter.
• Stainless steel impeller.

Multiple discharge hookup options

• Easily hook up to a Garden Hose* or Discharge hose* (*not included)
• Easy to transport using the carrying handle.
• 10 ft. power cord.

Intake Screen

• Intake screen filters out debris from entering the impeller. This helps reduce the clogging and prolongs the life of the pump.
• Easily to clean and is removable.

Motor and Performance

Motor:

• 1/2 HP Superior Pump continuous duty, thermally protected - split capacitor motor

Performance

• 3300 Gallons per hour at 0'
• 2520 Gallons per hour at 10'
• 1500 Gallons per hour at 20'

Product description

Submersible water pump

• Simple Operation, Automatic Sensor Switch
• 1/3 HP HIGH POWER - 1/3 HP, pump 42.5 gal of water every minute, with a maximum flow rate of 2550 gallons per hour. Up to 25 ft in vertical height, provides the necessary power for any arduous task
• On/Off SENSOR- The smart electronic sensor automatically turns on when the water level is over 1.5 inches and shuts off when it falls below 1/4 inches
• 3/4 in Adapter Check Valve- To prevent reverse flow of water during use of the pump, each pump is equipped with a check valve. Notice: the water level must be at least1-1/4 inches to allow the pump to cycle, charge and operate. Less than 1/4 inches, pump stop working
• Anti-CORROSION- With a durable thermoplastic structure and a compact design, the product uses copper nickel plated pump head to resist oxidation and not to corrode
• APPLICATION- the pump suitable for use in farms, swimming pools, fountains, flooded basements, and drainage in typical residential or commercial water transfer applications

User questions & answers

Question:	Once i plug it in do i need to monitor it or will i not have to worry about being away from home when the rain comes? set it and forget it
Answer:	This is so easy to use, it will automatically turn on and off without monitoring
Question:	Is this pump corrosion resistant
Answer:	It's okay. After using it for a month, it still shows no rust. It may be that his shell is made of special materials, but it is a clean water pump and cannot be put into sewage.
Question:	will this work good in a 16 foot swim spa? My spa doesn't have a drain plug. Will this work? It is about 5 foot high walls
Answer:	Yes my pump is used to pump ground water from around my pool. It pumps 10ft vertically without a problem
Question:	Is check valve required
Answer:	Yes, this pump is equipped with a 3/4 in adapter check valve to prevent water backflow.

Product features

Unattended Smart Automation Submersible Pump

Smart electronic sensor automatically turns on when the water level is over 1-1/4 inches and shuts off when the water level falls below 1/4 inches

Product description

The Wayne CDU980E submersible sump pump can move up to 5490 gallons per hour (gph). The top suction design filters debris and minimizes clogging. It is a rugged, stainless steel and cast iron submersible sump pump. This pump is designed for 11-Inch diameter and larger sump pits. Intended for indoor use only.

From the Manufacturer

The Wayne CDU980E submersible sump pump can move up to 4600 gallons per hour (gph). The top suction design filters debris and minimizes clogging. It is a rugged, stainless steel and cast iron submersible sump pump. This pump is designed for 11-Inch diameter and larger sump pits.Intended for indoor use only.

• Assembled in the US with foreign and domestic parts
• Top suction pump design minimizes air locks and clogging from debris in bottom of sump pit.Assembled in us, with foreign and domestic components
• Stainless steel motor housing and rugged, cast iron pump base
• Vertical float switch, tested to 1 million cycles!4600 GPH at 10 ft. of discharge lift
• 1-1/2 In. NPT Discharge for compliance with building codes

User questions & answers

Question:	Can this pump be hooked up to a battery backup
Answer:	It pulls too much current for most battery backups, a generator will run it fine.
Question:	how long is the power cord
Answer:	Just received my Wayne CDU980E. I, too, was concerned with this question. Power cord measures about 90-inches (7.5-feet) from where it connects to the top of the sump motor (which is about 11-inches above the bottom of the pump). I can't find this marked on Wayne's literature for the CDU980E.
Question:	When the pump is switched on by the floater, how long does it run
Answer:	If there is merely water in the sump pit, you don't need this powerful a pump. This 3/4 HP pump is for handling major water flowing into the pit. When that happens in our cellar, the pump runs until it out-runs the flow of incoming water.-- sometimes for minutes sometimes for hours. We have 4 sump installations in 4 buildings. When the water table (level of the ground water in the outside ground) is high, three of these systems pump a lot of the time and pretty constantly. We have 2 pumps in each pit so if one fails we do not get flooded. Each Pump (if more than one in the system) needs to have a check valve/ back-flow preventer so it will force the other pumps to actually pump the water up and out and not allow an operating pump to to just pump back out through the other , (not then pumping) pump. The should also be placed at different levels so they don't necessariy go on at the same time, thus reserving one as a kind of back up. Of course, if there is really a lot of incoming water -- which we had when we first bought our house, it takes both pumps to handle the in flow and avoid flooding. NOw that we use the large diameter PVC piping, it works so much better that a single pump pof this size would probably be fine. It is best to pipe the pumps with real PVC pipe and in 1 1/2" or 2" size. This will increase the flow rate by around twice as much flow as the skinny (1 1/4") highresistance black curly-sided plastic pipe they often come with. Good luck and stay dry.
Question:	when you say 'top suction' does this mean the pu,p must be totally submerged
Answer:	The pump draws water from the "LOWER" part of the pump a few inches off the floor. It does not have to be completely submerged to draw water. When the bulb float rises enough to turn on the float switch it sucks water. It turns on before the water reaches the top of the pump. I use this one and I know. Hope this helps someone.

Product description

Superior Pump builds pumps that are truly Built to Last and are 100 percent factory tested. Superior Pump pedestal pumps use quality components including solid copper motor windings, electronically controlled split capacitors, heavy duty drive shafts, stainless steel impellers and 10 foot power cords. Superior Pump model 92333, 1/3 HP thermoplastic pedestal sump pump, will move water up to 3000 gallons per hour. This pump features a corrosion resistant steel drive shaft, stainless steel impeller, and metal switch arm for strength and durability. This pump is UL/CUL listed and CSA certified and backed by a 1 year warranty.

From the Manufacturer

At Superior Pump we build high quality pumps. With a combined 150 years of pump industry experience every product is built using cutting edge innovative technology and high quality components. Our products are BUILT TO LAST and are supported by an industry standard warranty and excellent customer service. Come see what makes our products different.

• 1/3 HP Sump pump moves up to 3,000 gallons per hour; pump will lift water up to 20' of vertical height
• Tough thermoplastic construction; 10' cord length
• Durable non corrosive steel drive shaft and stainless steel impeller; metal switch arm for strength and durability
• 1-1/4 inch NPT discharge for high capacity pumping
• Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested

User questions & answers

Question:	Are you able to rotate the motor on the shaft to line up the discharge pipe and the float rod to fit the existing holes in your basin cover
Answer:	Yes I have to do that to fit in the sump hole which is a standard plastic 5 gallon bucket recessed in floor.
Question:	Description says cast iron but looks like plastic
Answer:	look close they sale both be sure you order the right one
Question:	How many volts
Answer:	a Normal house outlet of 110 to 120 Volts will work to run your pump . But if your elect go out your pump will not work.
Question:	Is anything else needed to operate? The manual diagram shows a check value. Also, can this be place directly on the basin bottom or is a riser needed
Answer:	Hi there, We do recommend a check valve within a foot or so from the base and attaching it directly to the pump is even better. Thanks.

Product features

Superior Pump 92333 1/3 HP Thermoplastic Pedestal Sump Pump with Automatic Float Switch

Superior Pump builds pumps that are truly Built to Last and are 100 percent factory tested. Superior Pump pedestal pumps use quality components including solid copper motor windings, electronically controlled split capacitors, heavy duty drive shafts, stainless steel impellers and 10 foot power cords. Superior Pump model 92333, 1/3 HP thermoplastic pedestal sump pump, will move water up to 3000 gallons per hour. This pump features a corrosion resistant steel drive shaft, stainless steel impeller, and metal switch arm for strength and durability. This pump is UL/CUL listed (E238091, by UL, 2019) and CSA certified (230584, by CSA, 2019)

Automatic Switch

• Float switch automatically turns on and off pump depending on the water level in the sump basin/pit.
• Metal switch arm for improved peformance
• Thermoplastic rod guide and float ball
• Adjustable switch on height

Construction, Intake and Discharge

• Thermoplastic construction is corrosion resistant and offers years of performance and reliability.
• Top intake filters out debris.
• 1-1/4" NPT discharge for use with 1-1/4" discharge pipe.

Impeller and Drive Shaft

• Stainless steel twin blade impeller for high capacity pumping.
• Non-corrosive steel drive shaft.
• Removable base plate for easy service.

Motor and Performance

Motor

• 1/3 HP Superior Pump continuous duty, thermally protected - split capacitor motor

Performance

• 3000 Gallons per hour at 0'
• 2280 Gallons per hour at 10'
• 900 Gallons per hour at 20'

• Plastic
• 【3/4 Inches Adapter Check Valve】- Each pump is equipped with a check valve to prevent reverse flow of water during use of the pump. It must be noted that the water level must be at least 1-1 / 4 inches to allow the pump to cycle, charge and operate. A water level of less than 1-1 / 4 inches does not allow the impeller to come in contact with the water and therefore does not pump water
• 【1/3 HP High Power High Efficiency】- The smart pump can pump 42.5 gallons of water every minute, with a maximum flow rate of 2550 gallons per hour. 1950 gallons per hour on a 10-foot discharge lift, up to 25 feet in vertical height; provides the necessary power for any arduous task
• 【Reinforced Sealing Thermoplastic Structure】- The pump features a durable thermoplastic structure and a compact design to ensure that the submersible pump can be used again and again without corrosion, Remove stagnant water from any environment, suitable for use in farms, swimming pools, fountains, flooded basements, and drainage in typical residential or commercial water transfer applications
• 【Automatic ON/OFF Electric Water Removal Pump】- Tacklife's unique switching technology turns the pump on and off by sensing the presence of water, 10-inch power cord and comfortable handle structure, As long as the pump is plugged in, the pump can be left unattended. You don't have to worry about removing the water. It will move the water to within 1/4 inch of the ground
• 【4 Amp Pure Copper Motor with Thermal Protection】- Pure copper motor can bring better and more lasting work to the pump,Overheat protection ensures that the pump will not be burned out,The bottom grid suction is designed to filter debris and has an anti-clogging force to remove the standing water from any enclosed environment

User questions & answers

Question:	At what water height does the pump automatically turn on
Answer:	1 gallon
Question:	My pump is six weeks old but does not automatically shut off. Is there a troubleshooting solution
Answer:	30psi
Question:	Does it have automatic shut off sensor
Answer:	The pump doesn't have an on and off switch. It needs to be plugged in to turn it on and unplugged to turn it off.
Question:	What are the pump's actual dimensions
Answer:	Yes

Product features

1/3 HP Automatic ON/OFF Electric Water Removal Pump

Unattended Smart Automation Submersible Pump

◆ Smart electronic sensor automatically turns on when the water level is over 1-1/4 inches and shuts off when the water level falls below 1/4 inches

Product description

Plug in and leave the pump unattended for worry-free water removal. Ideal for crawl spaces, flat roofs, window wells and other problem areas around the home where water accumulates.

Troubleshooting:

Primary causes for malfunction impacting the automatic switching function:

o A clogged vent hole (small debris, seeds, pine needles)

o A contaminated switch housing (algae, slime or other materials accumulated on the switch underside).

From the Manufacturer

Plug in and leave the pump unattended for worry-free water removal. Ideal for crawl spaces, flat roofs, window wells and other problem areas around the home where water accumulates.

• I switch technology turns pump on and off by sensing the presence of water; removes water down to 3/8 in. Of surface
• 1/4 hp; max. Flow rate is 3000 gallons per hour; 1850 gph at 10 ft. Of discharge lift
• Can be left unattended to remove water
• Submersible reinforced sealed thermoplastic construction.Voltage:120V
• The water level must be at least 1-3/4 inches for the pump to cycle, prime, and operate. Water levels less than 1-3/4 inches will not allow the impeller to contact water therefore no water will be pumped. Garden hose adapter

User questions & answers

Question:	I currently have window well pumps that "check" for water every so often. Wondering how the thermaplastic holds up in winter/cold? Any concerns
Answer:	This is our first winter for the pump. Ours sits in a bucket with washed stone under and around the bucket. Our window well is also covered for the winter . We'll find out for sure in a couple months.
Question:	Can I leave this pump outside year round? Will it freeze up? How cold can it be before I have to take it inside
Answer:	I packed up the pump and stored it indoors for the winter. The freezing and thawing will not be good for the unit.
Question:	Is this pump corrosion resistant
Answer:	Yes
Question:	is check valve required
Answer:	A check valve is not required, but would be a good idea to have one on the pump.