10 best jet polishers

Product description

The heavy-duty one-horsepower 8-inch variable speed industrial bench buffer is engineered with a full casted body and loaded with safety innovations. The exclusive motor stop will reduce RPM speed from 3, 600 to 0 in less than 20-seconds bringing the buffing wheel to a complete stop.

• Massive cast iron body; variable speed provides wide range of RPM's
• Totally enclosed pre-lubricated ball bearings
• CSA/cuts: following strict guidelines and electrical requirements, this Jet industrial buffer is CSA/cuts certified
• Brake Resistor added for Rapid wheel stoppage
• Rubber mounts prevent movement

User questions & answers

Question:	Can you reverse the rotation
Answer:	Mine works great.
Question:	What voltage and phase is this unit? I didn't see it specified anywhere
Answer:	It depends what you are buffing for type of wheel but the main thing is keep it 6" or smaller. This is not a powerful buffer and it is easy to stop (over load). The larger the wheel the more torque on the motor...
Question:	Vfds do reduce the hp. i'm curious as to how low a speed someone has run this and how well did it do? anyone run one at say 800 rpm or lower
Answer:	3/4
Question:	What are the rpm's from low to high speed. I need something in the 1000 to 1200 rpm
Answer:	3450 as the label on the front says

• This air prophy is a proven ergonomic and easy to use air-driven dental air polishing lightweight unit. That makes routine cleaning and polishing procedures easier, and more efficient than ever before
• The teeth polisher is a compact bicarbonate-jet whitening system with a quick-fit connection to the turbine. The main advantages are steady efficient stream of powder and simplicity of use.
• The attractive design allows for dexterous handling and manipulation.360º rotation assures effective hidden tartar removal. Disperses evenly with no splashing. Specially designed to prevent backflow and blockage
• The calculus remover is easy to clean and simple to maintain, enable to remove the stain, polish the teeth and massage your gums easily and effectively. Easy to be connected with 2-hole high speed connecting hose
• Auto clavable temperature: 135ºC Connection: 4-hole Water Pressure: 0.05MPa - 0.5MPa Air Pressure: 0.2MPa-0.5MPa Max. Waterflow: 30ml/min Max. Powderflow: 2g-3g/min

• This air prophy is a proven ergonomic and easy to use air-driven dental air polishing lightweight unit. That makes routine cleaning and polishing procedures easier, and more efficient than ever before
• The teeth polisher is a compact bicarbonate-jet whitening system with a quick-fit connection to the turbine. The main advantages are steady efficient stream of powder and simplicity of use.
• The attractive design allows for dexterous handling and manipulation.360º rotation assures effective hidden tartar removal. Disperses evenly with no splashing. Specially designed to prevent backflow and blockage
• The calculus remover is easy to clean and simple to maintain, enable to remove the stain, polish the teeth and massage your gums easily and effectively. Easy to be connected with 2-hole high speed connecting hose
• Auto clavable temperature: 135ºC Connection: 2-hole Water Pressure: 0.05MPa - 0.5MPa Air Pressure: 0.2MPa-0.5MPa Max. Waterflow: 30ml/min Max. Powderflow: 2g-3g/min

• Free speed: 4300 RPM; Disk diameter: 4inch; Working pressure: 6-8 kg; Air inlet size: 1/4 (inch).
• Mini air polisher sander-Light Weight, High stability,High Speed and Easy one-hand operation.
• Sanding pad is made of polyurethane,flexible and very durable to minimizes heat transfer.
• Applicable Industry: Stone, jade, ceramic polishing, finish your projects smooth and perfect.
• Worry-free Shopping: If you have any questions, please feel free to contact us, we will spare no effort to help you. Our products are sent from the US and can be delivered quickly, you will receive it within 3-7 days.

• Compact ergonomic design
• 360° rotation assures effective hidden tartar removal
• Disperses evenly with no splashing
• Specially designed to prevent backflow and blockage
• Easy operation, clean up, and maintenence

• The nozzle measures 1 7/16" long and ½" in diameter.
• Tip length / Bore: (1 3/8") long. Tip diameter: (1/2") wide.Tip inside diameter: (1/4") I.D. Inlet: 1"
• Tips are made of steel.
• This tip is usually used for siphon type prophy jet
• These tips fit many of different brands of dental air polisher, if the measurement of the tip you currently have is the same outside diameter and pretty close in length, these will work.

• Compact ergonomic design
• 360° rotation assures effective hidden tartar removal
• Disperses evenly with no splashing
• Specially designed to prevent backflow and blockage
• Easy operation, clean up, and maintenence

Product description

◆Technical:

◆1. Auto clavable temperature: 135oC

◆2. Connection: 2-hole

◆3. Water Pressure: 0.05MPa - 0.5MPa

◆4. Air Pressure: 0.2MPa-0.5MPa

◆5. Max. Waterflow: 30ml/min

◆6. Max. Powderflow: 2g-3g/min

◆Packing list:

◆1 x Air polisher

◆1 x Spare covers

◆1 x Nozzle

◆1 x Nozzle cleaner

◆1 x Gasket

◆1 x Instruction manual.

◆Note:

◆1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.

◆2.Please allow 0.1-0.5cm error due to the hand measurement.

• ◆ It is a proven ergonomic and easy to use air-driven dental air polishing lightweight unit. That makes routine cleaning and polishing procedures easier, and more efficient than ever before
• ◆The teeth polisher is a compact bicarbonate-jet whitening system with a quick-fit connection to the turbine. The main advantages are steady efficient stream of powder and simplicity of use.
• ◆ The attractive design allows for dexterous handling and manipulation.360o rotation assures effective hidden tartar removal. Disperses evenly with no splashing. Specially designed to prevent backflow and blockage
• ◆The calculus remover is easy to clean and simple to maintain, enable to remove the stain, polish the teeth and massage your gums easily and effectively. Easy to be connected with 2-hole high speed connecting hose
• ◆ Auto clavable temperature: 135oC Connection: 2-hole Water Pressure: 0.05MPa - 0.5MPa Air Pressure: 0.2MPa-0.5MPa Max. Waterflow: 30ml/min Max. Powderflow: 2g-3g/min

Product description

For shops that may be short on space, a cast iron JET Bench Grinder with Wire Wheel delivers work power and dual options in polishing, deburring, edge blending, finishing, and more, all on one machine. Built to withstand the high-volume demands of even the busiest shops, this high-quality machine grinds, sharpens and smooths with equal precision for flawless results.

• PLENTY OF POWER: Heavy-duty 1/2-HP motor spins wheels at 3,450 RPM.
• VERSATILITY: Includes a 36-grit vitrified aluminum oxide wheel, and a crimped wire wheel.
• ADAPTABLE: Pre-drilled base for mounting on a stand or workbench.
• HEAVY-DUTY: Cast iron construction can handle demanding environments.
• SAFETY: Cast iron wheel guards and dust ports, and adjustable eye shields and spark guards.

User questions & answers

Question:	What is the depth? Have a 2x12 it needs to fit on. Depth in desc. shows 11” but I read elsewhere it was
Answer:	The overall depth is 12.2".
Question:	Is this battery powered
Answer:	The Jet 577126 Shop Grinder is not Battery Operated. This bench grinder requires 110V power supply.
Question:	what size wheels can be used
Answer:	6 inch with 1/2 inch arbor
Question:	will the 3W LED light work with this grinder
Answer:	I bought the light with the grinder, but there is no provision on the grinder to mount this or any other light. Very misleading ad for the light. Grinder is a good one though.

Product description

For shops that may be short on space, a cast iron JET Bench Grinder delivers work power and pristine finishes. Built to withstand the high-volume demands of even the busiest shops, this high-quality machine grinds, sharpens and smooths with equal precision and flawless results.

Perfect for cleaning, sharpening, buffing, removing rust, or removing burs from metal, the Jet 577101 JBG-6A bench grinder comes with industrial-grade 36-grit and 60-grit 6-inch wheels for maximum versatility. The 1/2-horsepower, 115-volt motor operates at 3,450 rpm and delivers plenty of power for heavy grinding. The grinder sits on a rubber foot to prevent unwanted movement and can be bolted down if desired for maximum stability.

The Jet 577101 features totally enclosed pre-lubricated ball bearings, cast-iron wheel guards and dust vents, one-piece quick adjusting spark guards, and large eye shields with quick adjustment for maximum safety. It's backed by a 2-year limited warranty.

What's in the Box

One Jet 577101 JBG-6A bench grinder, two 6-inch wheels (36-grit and 60-grit), hardware, and operating and assembly instructions.

Specifications

• Motor: 1/2 horsepower, 1 phase, 115 volt
• Wheel diameter: 6-inch diameter, 3/4-inch thickness
• Wheel speed: 3,450 rpm
• Wheel grits: 36 and 60
• Shaft diameter: 1/2-inch
• Dimensions: 18 inches by 10-1/2 inches by 8-1/2 inches
• Warranty: 2 years, limited

From the Manufacturer

If you have things that need cleaning, sharpening, buffing, removing rust, or removing burs from metal, then you need a grinder. The JET 6" Industrial Bench Grinder features heavy duty construction with powerful, long-life motor for use all day, every day. It comes standard with fine and coarse vitrified grinding wheels, cast iron wheel guards and dust vents, and more.

• CSA LISTED: Follows strict guidelines and electrical requirements to meet CSA safety standards
• BUILT FOR DURABILITY: Has cast iron wheel guards and dust vents
• ENCLOSED BALL BEARINGS: Has totally enclosed pre-lubricated ball bearings
• NO SHIFTING: Rubber mounts prevent movement
• GRINDING WHEELS INCLUDED: Fine and coarse vitrified grinding wheels included

User questions & answers

Question:	What rpms does it run at
Answer:	This bench grinder runs at 3,450 RPM.
Question:	What is the size of the dust ports
Answer:	The dust ports on my grinder are "oval", approximately 1 3/4 x 2 1/2".
Question:	Can anyone tell me the distance between the mounting holes and the overall length of the base? Thanks
Answer:	Mine is about 15 years old, so dimensions may have changed. The base is about 7 5/8 inches wide and the holes are about 6 1/2 inches apart and a little over 3/8 inch in diameter.
Question:	Is this made in China or Taiwan
Answer:	China, where else. iIdid not like the finish work, rough castings for tool rests.