11 best cen tech clamp meter

Product description

Digital Clamp Cen-tech Multimeter Volt Amp Meter New W/Case * AC Voltage: 4V - 40V - 400 - 600V * DC Voltage: 4V - 40V - 400V - 600V * AC current: 0 - 400A - 600A * Resistance: 0 - 600 - 6K - 60K - 600K - 6M - 60M * Ohms Capacitance: 600nF - 6uF - 60uF - 600uF - 1000uF * Frequency: 40Hz - 600Hz - 6KHz - 60KHz - 100KHz * ADP: 600mV Frequency measurement for clamp: 40 Hz - 400 Hz * Auto zero on all features Max and Min memories * Data hold, Back light on LCD and Flash light * Auto Power off Accuracy : 2.5% of reading Max * Common mode voltage: 600V * AC current:600A AC/DC RMS Display * LCD 5999 Range, Auto Over range indicator * Reading hold: H on the display Power supply * 3 X 1.5V AAA Power Consumption: 50mW

• LCD 5999 Range, Auto Over range indicator
• Reading hold: H on the display Power
• Auto Power off Accuracy : 2.5%
• Auto zero on all features Max and Min
• AC DC Voltage AC current Resistance

User questions & answers

Question:	whats the smallest ac amps it will read... any good for checking one lamp ballast at a time
Answer:	The display for TDS can be set to show TDS as ppm.
Question:	Will the unit measure and display inrush current on startup of an air conditioner compressor
Answer:	Yes it reads ppm and ec
Question:	Is this a trms meter
Answer:	These are longer than that. About 5/5.5 mm
Question:	Does it retain max values? I want to measure start-up and continuous current for a fridge and a furnace
Answer:	Not a professional piercer, but if there is any swelling at all, I think these would be too short in the posts. And you certainly couldn't use them with a punch gun.

Product description

Etekcity's Digital Clamp Mustimeter ensures household electricity maintenance safe.

• Accurately Measures: AC/DC voltage, only for AC current (not for DC current), resistance, and also provides diode and continuity tests
• Jaw Opening: the Clamp measures the AC current in a conductor up to 26mm without interrupting the circuit
• Additional Features: data hold, max reading, and an easy-to-read large LCD
• Easily Carrying: comes with a handy carrying pouch, perfect for use while you're on the go
• Sleep Mode: automatically enters sleep mode after 15 minutes of inactivity for energy conservation

User questions & answers

Question:	can i get an accurate amp reading on kitchen appliances such as toasters, microwaves with this meter
Answer:	Sounds like what you need is a Kill-A-Watt meter (brand name). You plug the meter in the wall then plug the appliance in the meter. Real simple. Gives amps, watts, volts, etc.
Question:	Can the clamp measure voltage without load
Answer:	The clamp (non-contact) can only measure current (amperage), not voltage. To measure voltage, you'd need to use the probes on a physical connection (terminal or bare wire).
Question:	I am working on a light fixture - if I want to test the actual wires (and not outlet) to see if they're live, what setting would I need to do this on
Answer:	Nobody else said it, but if you use the clamp meter, it must be around a SINGLE wire, it will not work if you clamp around both wires of the cable. You must separate the wires, and clamp only one wire. And the clamp is only gonna measure current, so if the lamp isn't working, this probably won't work. If the plag is plugged-in though, there will be a voltage present, so a non contact voltage tester should be sufficient enough to tell you it's live. Please be careful.
Question:	people said it has an audible beep for continuity and 2 people said it doesn't. What is the true answer
Answer:	It does have an audible beep for continuity. It is an option that must be activated by pushing a button to enable this feature of continuity testing.

Product features

All Purpose Multimeter

The Etekcity Multimeter combines ease of use with innovation, making it the perfect tool for any electrical project.

Easily test AC/DC Voltage, diode, continuity, and resistance. Avoid hazardous situations by using the convenient clamp to safely measure AC currents without having to strip a cord or break a circuit.

It also features hold result and max value buttons that makes it quicker and easier to use.

The autoranging function helps you get precise measurements, every time.

Safe & Simple

Safely measure AC currents with the clamp, so you don’t have to strip any wires.

Voltage Test

Get quick and accurate results when you test both AC and DC voltage.

Multifunctional

Take advantage of multiple functions such as HOLD, MAX, and SELECT.

Autoranging Assistance

The autoranging function allows you to get quick and accurate results.

Diode & Continuity

Ensure that all your electrical connections are correct and safe.

Auto Off

The auto off function saves battery life to maximize your usage.

LCD Display

The easy-to-read LCD display gives you clear measurements.

Unpacking

Comes with a user manual and convenient carrying case.

• True-RMS clamp meter: This multimeter can accurately measure AC/DC Current, AC/DC Voltage, Frequency or Duty Cycle, Resistance, Capacitance and also provides Diode, Continuity and Temperature tests. True RMS for accurate measurements on non-linear loads. Easy to use for labs factories and household.
• LowZ & LPF: Low input impedance helps prevent false readings due to ghost voltage. Low Pass Filter (LPF) for accurate measurement of variable frequency drive signals when measuring motors and transformer. To measure the current you need to clamp the meter around one of the wires and not the whole power cord.
• NCV Detection Function: Non-contact voltage detection effectively check electrical status through measuring EM field intensity without touching any wires; The NCV button lies on the right side. Simply place your thumb on it and push.
• Multi-function: Two-color backlit LCD Display - When the voltage > 80V, the current > 3A, the LCD backlit screen turns red to warn you of high voltage/ LED Flashlight / Temperature Measurement for liquids and air conditioning ports included K-Type Thermocouple / Low Battery Indication / Auto power off after 15 minutes inactivity.
• Safety Service: Safety standard IEC 61010-1, CAT III 600V. Double insulation. 36 Months product service provided. 7/24 Customer Service.

User questions & answers

Question:	What are the concrete tips for automatic shutdown
Answer:	Step 1.) Run around in circles until u get too dizzy to continue or 15 min has passed, then it will auto shut off. 2.) There is no step two. If you have further questions or need more concrete tips, just continue repeating step 1 until it sinks in.
Question:	W/ backlite on I tilt the meter away from me the display is readable but once I tilt it towards myself the display becomes unreadable, is this normal
Answer:	Yes, with the baclklight on, it's viewable from straight-on to tilted away from yourself, but with the top tilted towards you it loses all contrast. Side-to-side viewing angle is a good. This is a common trait among some LCD displays.
Question:	I want to measure current flowing to my car starter when cranking engine. Does this clamp on meter measure DC current when using clamp
Answer:	Yes, It can read DC starting current with the clamp when set to DC measurement. Reading moves fast but I take video with mobile phone camera and rewind to see the 268A when starting a Nissan Frontier 2.5 L engine. Reasonable current though I cannot check its accuracy yet. I buy meter to monitor DC charging current and confirm non-running car leaking currents under 50mA but need to wait 20 minutes after engine off to let car computer stabilize from initial shutoff which can cab be as high as 0.6A. With this meter, I also find about 10mV leaking voltage on plastic surface between terminals at new battery (due to acid filling spill at manufacturing?) from club store which I need to reduce the Voltage drop to less than 0.1 mV by scribing several grooves on plastics surface around terminal posts. Calibrate to zero by holding Z/F button few seconds before measurement can help read accuracy. I am happy with this meter for the price. Hope you too if do not have time to find a better cheaper on
Question:	how accurate is th DC current measurment
Answer:	I have not checked it against a reference, but I have done some measurements on my car with this. It seemed to reflect a reasonable value when the battery charger was on, showing charging current. and It showed a big current for the started that was believable. When you first set it, you can press a zero button to zero it out. Then I looked at a really bad solar panel that could only put out about 50 milliamps when shorted, and it was able to show that pretty well. So the bottom line, if you are going to use this for debugging stuff, it seems pretty good. If you are going to measure calorie input to control a chemical reactions in a pharmaceutical lab, I can't say. For me, it is just cool that it can do a DC current in the first place. Has already come in handy as I was able to determine my alternator was not charging my battery quite easily.

Product features

To measure Direct Current

Specifications:

If current> 3A, the orange display lights up.

The measuring range of DC current is 60A/600A. Accuracy: ±(2.5%+5).

Note:

Before measuring the DC current, long-press and hold the Z/F key until the ZERO character appears to clear the data.

To measure Alternating Current

Specifications:

If current> 3A, the orange display lights up.

The measuring range of AC current is 60A/600A. Accuracy: ±(2.5%+5).

Note:

To measure the current you need to clamp the meter around one of the wires and not the whole power cord. The power cord contains two wires carrying current and ground wire. The current in two wires always flows in opposite directions, so the magnetic fields from two wires canceling each other, therefore the meter reads 0 A.

Grasp the individual current conductor to be measured and close the current clamp again. The measured conductor must be placed in the center of the clamp, otherwise, additional errors will occur.

Jaw Design

The Jaw is marked with maximum voltage and current measured value. Suitable for one-hand operation.

Weight & Size

Weight :260g. Size: 7.5 x 2.8 x1.3 inches.

Small and light, easy to carry when working.

Packing List

1 x Kaiweets Digital Clamp Meter 1 x Test Leads (Pair), 1 x Thermocouples(Pair), 2 x AAA batteries, 1 x User Manual, 1 x Carrying Bag

Z/F Button Measurement

Press the "Z/F" button to switch the respective secondary function between the different measurements such as between AC and DC.

Automatic Shutdown

No operation in 15 minutes, the clamp meter beeps 3 times. Without further operation, it beeps again and switches off automatically.

Multi-Function

Accurately measure resistance, capacitance, diode, continuity. Easy to use in laboratory factories and homes.

Product description

The Fluke 117/323 KIT Multimeter, 117 Digital Multimeter/323 TrueRMS Clamp Meter Electrician's Combo Meter Kit Fluke 117/323 KIT Fluke Multimeter, 117 Digital Multimeter/323 TrueRMS Clamp Meter Electrician's Combo Meter Kit pairs the Fluke 117 multimeter with a Fluke 323 clamp meter for productive and effective troubleshooting in one total solution, including the New C115 durable soft carrying case for protection and easy meter transportation. Replaces: Fluke 117/322 KIT.

• The 117 multimeter measures AC and DC voltage as well as AC and DC amps. The 323 clamp meter measures AC and DC voltage as well as AC amps
• The 117 multimeter features true RMS for accurate measurements on non-linear loads
• The 117 multimeter features low input impedance which helps prevent false readings due to ghost voltage
• The 323 clamp meter provides a true RMS AC voltage and current for accurate measurements on nonlinear signals
• The 323 clamp meter measures 400 A AC current and 600 VAC and DC voltage

User questions & answers

Question:	Looks like the 117 includes a non-contact voltage detector. does that mean i don't need a separate non-voltage detector, i.e. 2ac av tester
Answer:	It will sense AC voltage with no contact if within range.
Question:	Why is the 116 better for hvac guys than the
Answer:	The only major differences between the 116 and 117 are thermometer and non-contact voltage detection features, the 116 having the thermometer but not non-contact. I would make a conclusion that HVAC technicians would have more use for a thermometer on the job, where electricians have more use for non-contact.
Question:	Made in the usa or china
Answer:	Mine says designed in USA. I doesn't say exactly where it was made. It is one of the best multimeters you can buy anywhere, regardless of where it was assembled.
Question:	Does this kit come with test leads & the magnetic meter hanging strap
Answer:	Hello,Thank you for your message. The Fluke117/323 comes with the follow: 117 TRMS Digital Multimeter w/ Non-Contact voltage detection 323 AC/DC True-RMS Clamp Meter TPAK ToolPak Magnetic Meter hanging Strap C115 Deluxe carrying case with shoulder strap TL175 TwistGuard Test LeadsIf you have any further questions feel free to contact us. Thank you for visiting our store front.Regards,Customer Service

Product features

Fluke 117 / 323 - Electrician’s Combo Kit

The Fluke 117/323 Electricians Multimeter Combo Kit gives you the best in a versatile, rugged multimeter and a fast-acting, general purpose clamp meter.

The Fluke 117 is the ideal meter for demanding settings like commercial buildings, hospitals and schools. The 117 includes integrated non-contact voltage detection to help get the job done faster.

The Fluke 323 True-rms Clamp Meter is suited for current measurements up to 400 A in a tight cable compartments.

Non-Contact Voltage Detection

The 117 includes integrated non-contact voltage detection to help get the job done faster.

Electrical Maintenance troubleshooting

Eliminate false or 'ghost' voltages or perform continuity, connection or basic wiring checks with the Fluke 177.

Measurement capability

The Fluke 323 measures resistance up to 4 kΩ with continuity detection.

Compact design

The Fluke 323's compact design is suitable for one hand operation and tight cable compartments.

• ACCURATELY MEASURES: AC/DC Voltage, DC Current (Not AC Current), Resistance, Continuity, Diodes and more.
• TROUBLESHOOTS SAFELY: Automotive and household electrical problems safely and accurately; Overload protection on all ranges
• EASE OF USE: Data hold and large digital display with backlit LCD for visibility in dimly light areas; Sampling speed: 2x per second
• 1 Year Warranty. Built-in kickstand for hands-free use. Protective rubber corner guards for drop protection
• NOTE: This meter can not test AC Current; Ensure your multimeter is set to the correct setting before testing

User questions & answers

Question:	which setting is for volts, and which is for ac
Answer:	The V with the two lines is DC volts and the line with the squiggly line is AC volts.
Question:	is the continuity test audible
Answer:	Good question. and I can't find an answer it doesn't say but in the picture when it's showing someone testing continuity it shows that it's beeping what it doesn't say that it does beat and we've got two people on here that say it does not and two people that say that it does so good luck I'm looking for one that is audible myself why all multimeters don't have an audible noise when you have continuity I will never know either that or you can have one that has a paper thin needle that jumps and you can't see it and you have to take your eyes off of what you're working on to see if you have continuity and when you move your head you lose contact and it's such a pain in the ass
Question:	Is this unit protected by a fuse? If so, is it replaceable? My last meter was fused but it was soldered. I couldn't easily replace it
Answer:	I had to replace the ammeter fuse (because I forgot to switch the hot (red) test lead from the left side to the middle, before testing my car's battery voltage). That fuse is 10A 600V. I looked around for those & couldn't find them, but found 10A 250V and these worked OK. They're 20 x 5 mm ( .2 x .79") ceramic fast-blow. https://www.amazon.com/gp/product/B07JFDTTMJ/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
Question:	Can this handle being plugged into a wall socket? Also, can someone give a walkthrough of how to safely test a socket
Answer:	plug the red lead into the meter socket marked COM and the black into the center meter socket. Set the dial to V~ (for AC volts) on the 200 scale (for household current) insert one probe lead into each of the wall socket's vertical slots and move them around a bit inside the outlet slots to make sure you're getting a good connection, if in doubt plug a lamp or something into the socket. If you suspect the outlet socket itself has failed carefully remove the wall plate in order to access the actual wires connected to the outlet to be sure it's either a dead circuit or the outlet itself has failed.

Product features

AstroAI Digital Multimeter

The AstroAI AM33D Multimeter is designed to safely and accurately troubleshoot a variety of automotive and household electrical problems. It's easy and safe to operate and features many different functions for measuring current, voltage, and resistance, as well as continuity, transistor, and diode testing, which is both for automotive and household uses.

Troubleshoot Electrical Problems

AstroAI multimeter is professionally designed to troubleshoot electrical problems or just for electronics training.

Continuity Test

Connect the test leads to two points on the circuit being tested.

Intelligent Anti-burn and Dual Fuse

Double Fuse Protection, more secure and reliable; This multimeter is designed with safety in mind. Overload protection on all ranges.

Backlit LCD

Large digital display with backlit LCD for visibility in dimly light areas.

Data Hold

When taking measurements and recording results, it is often easier to use the data hold function to freeze the data being displayed on the digital display.

Low Battery Indication

You can quickly know to replace the battery and continue working. so you never accidentally run out of juice.

Open Support Stand and Protective Rubber

Built-in kickstand for hand free use. Protective rubber corner guards for drop protection.

Product description

For the complete solution to HVAC troubleshooting the extra value packed HVAC Technician's Combo Kit, provides the ability to troubleshoot and solve problems more efficiently by providing all the needed accessories an HVAC professional would need in a compact carry case.

• Fluke 116 digital multimeter features built-in thermometer for HVAC applications
• Fluke 116 digital multimeter features micro amps to test flame sensors
• Fluke 116 digital multimeter low input impedance helps prevent false readings due to ghost voltage
• Fluke 323 true RMS clamp meter measures 400 A AC current and 600 VAC and DC voltage
• Fluke 323 true rms clamp meter features true RMS AC voltage and current for accurate measurements on nonlinear signals

User questions & answers

Question:	Will the Fluke 323 measure/capture maximum inrush amps
Answer:	No, the Fluke 323 doesn't have an Inrush function.
Question:	what is the category
Answer:	i did not purchase this Fluke kit, just the 116 meter. I believe the category would be Tools, with the sub category being Electrical Multimeters/Testing Equipment.
Question:	Does the magnetic strap attach to the 323 clamp on meter
Answer:	The magnetic strap is designed to be used with the 116 Multimeter, not the 323 Clamp Meter.
Question:	So this does everything the electrician's kit does + hvac options
Answer:	For the most part, yes. I actually bought this one because of the ability to diagnose flame sensor failures.

Product features

Fluke 116/323 HVAC Combo Kit - Includes Multimeter and Clamp Meter

The Fluke 116/323 HVAC Combo Kit gives you the best in a versatile, rugged multimeter and a fast-acting, general-purpose clamp meter.

The Fluke 116 measures resistance, continuity, frequency, and capacitance. It provides Min/Max/Average readings with elapsed time to record signal fluctuations and is CAT III 600 V safety rated.

True-rms measurements and compact ergonomics make the Fluke 323 Clamp Meter the best general-purpose meter for electricians. It is CAT IV 300 V/CAT III 600 V safety rated.

Fluke 116 HVAC Multimeter

The Fluke 116 was specifically designed for the HVAC professional. Measure voltage, resistance, continuity, frequency, and capacitance all in one tool!

Going beyond your standard multimeter functions, the Fluke 116 also measures temperature and microamps specifically for HVAC applications.

Fluke 323 Clamp Meter

The Fluke 323 features true RMS AC voltage and current for accurate measurements on non-linear signals.

Fluke 80BK-A

With the Fluke 80BK-A integrated DMM temperature probe; no need to carry a separate thermometer.

Measurement range: -40 to 260ºC

Accuracy: +/- 2.2 °C or 2% whichever is greater ((0 to 260 °C)

What's in the box?

TL175 Hard Point Test Lead Set.

ToolPak Magnetic Meter Hanging Strap.

Flexible Cuff Pipe Clamp

Thermocouple.

80BK Integrated Temperature Probe.

80AK-A Thermocouple Adapter.

C115 Deluxe Soft Carrying

Case with Shoulder Strap.

Test leads.

Soft case.

• 【Even higher Copper Core requirements】Contains 42 pure copper-core wires;Easily dealing with currents of 10A and preventing leakage issues from occurring.The nylon wire inside will make it withstand bending thousands of times without breaking or fraying.
• 【More secure and durable silicone string】Constructed with flexible PVC/PA material that is double-layered and -insulated.The silicone used is non-toxic,environment friendly and meets both the UL and RoSH standards.Using high quality materials ensures that the test leads are durable,flexible as well as having properties like freeze resistance and heat tolerance.
• 【Premium test tip and plug】Pure nickel plated copper test lead tips which does not easily break-off,has solid contact traits and speedy and stable measuring reaction times.And the kit will protect it against dust and oxidation.An efficient and stable connection is thus ensured.
• 【Home & Industry Application】Thanks to the CAT.II 1000V ratings 10A currents can safely be tested.Recommended for general measurements.2mm 10A alligator clips use with 20A meter probe.
• 【Quality guarantee】More than 10 years of experience in the production of multimeter accessories.

User questions & answers

Question:	Are the plugs for the meter end reverse banana plugs that will fit a Simpson 260-7 or standard ones
Answer:	Just looked at mine. The 0 to 85% Brix is the RANGE of Brix that this refractometer measures of sucrose. I use mine when making maple and birch syrup. Buy a few pipetts and have some steam distilled water on hand (not just osmosis water) to calibrate it. Great tool.
Question:	How long are the wires from plug to lead
Answer:	Yes, you can use the brix scale and ignore the alcohol scale.
Question:	Is this a counterfit?? The ad claims it is made by Sinometer. No where on the box,manual or meter shows the name Sinometer
Answer:	I don’t think so
Question:	How can you turn off the audio alarm? The alarm in my new meter will not turn off
Answer:	3ml
Question:	How many decimals places of accuracy does it have when measuring resistance or ohms. I need one that does fractional ohm readings to the 1000th
Answer:	No, this refractometer is not for measuring alcohol, it's for measuring the sugar content.
Question:	does this measure capacitance
Answer:	i'm sorry i can not confirm that it does we use it to test the ph in raw milk it should do ok .
Question:	item 37772 iinstruction availble
Answer:	Yes, they don't carry the manual calibration one anymore.
Question:	Can this multimeter test a 208 cable as well as a
Answer:	No
Question:	Does this come with the Thermal probe
Answer:	The Salinity range is 0-10.00 PPT.
Question:	Auto turn off to save battery life
Answer:	It can do both. It is set to a TDS conversion ratio of 0.71 by default (for 700), and can be changed to 0.5 in the Parameter Settings (Check User Manul > Table of Contents > Parameter Settings for how to change).

Product features

The DARKBEAM Test Lead Set with silicone insulated!

Silicone wire material characteristics

Anti-burning and High temperature resistance

High temperature resista-nce over 200 degrees.

Antifreeze and will not harden

Less than -50 degrees is still as soft as noodles.

Soft, Fold-resistant and no Knoting

Bold tinned copper wire with good electrical conductivity.

Double-layer insulated soft silicone injection molding, more safe and durable.

Universal Multimeter Plug

Standard 4mm right angle jack for most multimeters. The internal design of the plug is safe and has a sheath for dustproof insulation.

Premium test tip and plug

Pure nickel plated copper test lead tips which does not easily break-off,has solid contact traits and speedy and stable measuring reaction times.And the kit will protect it against dust and oxidation.An efficient and stable connection is thus ensured.

Alligator Clips

• Tight alligator clips ensure good conduction.
• Red and black color coded test leads help you avoid wires crossing or shorts while testing circuits.

• ▲Quick and Accurate AC/DC Amp Clamp Meter- Auto-ranging clamp multimeter measuring AC/DC current, AC/DC voltage, Resistance, capacitance, continuity, Temperature, diode and Frequency(Hz) ; A perfect troubleshooting meter to help you solve automotive or household electrical problems quickly and safely
• ▲Non-Contact Voltage Detection & Overload Protection - If AC voltage detected, the visible LED lights will shine and the beeper will sound(range is 90V-1000V); Only when testing current, the flashlight of multimeter shines; Overload Protection & Double Insulation Protection avoid electric shock, protect users from touching dangerous areas
• ▲Multifunctional & Easy to read - High-Definition Large Back-lit LCD provides better visibility in dark working area; ZERO function makes for decrease the data error influenced by the earth magnetic field, help you to obtain more accurate measurement; Automatically enters sleep mode after 30 minutes of inactivity for energy conservation; Data hold function; Low battery indicator
• ▲Solid With Free Extra Test Leads : Supplied with free batteries and test leads, all in a carrying pouch for direct use; The test leads are easy to grip; The design is Ergonomic and portable for easy use, perfect for both professional or new users
• ▲ What You Get: 1x Tacklife CM06 Digital Clamp Meter, 2x Test Leads, 2x AAA Batteries, 1x User Manual, 24 month service; Be assured of purchase Tacklife CM06 digital clamp meter multimeter, Please contact us at the first time if the multimeter has any problem

User questions & answers

Question:	What is the DC current measurment capaility? Are there no specs for this meter other than it can read up to 600v
Answer:	It uses a Hall Effect sensor so the AC rating is the same as the DC rating. This website has the specs that confirms that: https://www.wantitall.co.za/tools/multimeter-tacklife-cm01a-clamp-meter-4000-counts-auto-ranging-digital-tester-with-ncv-ac-dc-voltage__b01n014use I tried it on my motorcycle, and it read the starting current of ~75A fine. The paper manual said the same. I can't find an electronic copy. The Amazon UK site has more info. It shows the range as 40A/400A https://www.amazon.co.uk/dp/B01N014CTB HTH.
Question:	Is this meter fast enough to indicate max current draw on the battery cable of a starting vehicle
Answer:	I have used a similar meter to watch the combined starting and glow plug current on a diesel Sprinter. No problem. Since this uses a Hall Effect sensor, instead of routing the 400 amps *through* the meter, overrange current pulses should not be a problem.
Question:	What is the resolution of the current reading
Answer:	While this meter reads to 1 milliamp that doesn’t necessarily mean that it is accurate to 1 milliamp. It drifts quite a bit in the milliamp range. You are given the option to zero it out before taking a reading, but it does continue to drift. It is a marvel that a Hall effect meter that can read DC is offered at this price, but don’t expect +/- 1 milliamp accuracy. I am a physicist by training and at one time worked at Textronix, a premier provider of test and measurement equipment.
Question:	Can DC current be measured by the clamp
Answer:	It not only measures DC current accurately via the clamp but it also indicates the direction of the current. Due to the disagreeing answers on this question, I went ahead and bought it. It works really well for DC current and is going to be be an excellent tool trying to troubleshoot a vehicle battery drain. Just remember that not all clamps measure DC current. Most cheaper meters do not but this one works great for it.

Product features

Tacklife CM06 Clamp Meter 6000 Counts Auto-Ranging

The tool CM06 of TACKLIFE is a clamp meter with an automatic measuring range of 6000. It is easy to use and innovative. The clamp meter with convenient use can safely measure AC/DC current, AC/DC voltage, resistor, diode, on-off and capacitor without stripping or disconnecting the circuit to avoid dangerous situations.

The clamp meter also has "SEL" function selection keys, "Hz/%" frequency/duty ratio selection keys, "ZERO" automatic zero-setting keys, "HOLD" data retention keys, and backlight/working light keys.

Specification:

• Environmental conditions: 600V CAT. III, pollution degree: II, altitude <2000m
• Working environment humidity: 0~40°C (<80% RH, not considered when <10°C).
• Storage environment temperature and humidity: -10 ~ 60 ° C (<70% RH, remove the battery).
• Temperature coefficient: 0.1X accuracy / °C (<18 ° C or > 28 ° C).
• Maximum allowable voltage: 600V DC or 600V AC rms.
• Sampling rate: about 3 times / sec.
• Display: 33/4-digit LCD display.
• Overrange indication: The LCD will show “OL”.
• Input polarity indication: “-” is automatically displayed.
• Dimensions: 218mm X 78mm X 32mm
• Weight: no more than 280g (with battery)
• Clamp head opening maximum size: 26mm

Resistance, Diode, On-off, Capacitance measure

When you measure resistance, diodes, switches, and capacitance, be sure to turn off the power to the circuit under test and discharge all capacitors.

AC or DC Voltage&Current Measure

Rotate the measuring function selection turntable to the voltage test gear, and select the AC or DC voltage measurement function by pressing the "SEL" key. The black pen line and the red pen line are connected to the COM input jack and the INPUT input jack respectively. The voltage of the circuit to be tested is measured at the other two ends of the pen. The operation is simple.

NCV Voltage Induction and Test Wire

When the voltage induction area of NCV is close to 90-1000V AC voltage or fire line, the instrument will emit sound of sound and light alarm signal "droplet". Make the measurement safer.

Ideal Gifts For Your family & Friends to do some DIY at Home

• Upgraded UNI-T UT210E Pro with larger range, faster reading, and new features. Versatile for diagnose automotive, repair, troubleshoots, industrial and household electrical issues. All in one.
• True-RMS & auto ranging. Accurately measure ac/dc current (1mA-100A), ac voltage (1mV-600V), dc voltage (0.1mV-600V), frequency (10Hz-60kHz), capacitance, resistance, diode test, continuity, etc.
• Ultra safe and built to last. Safety rated CAT II 600V, CAT III 300V. Built in smart chip for overload protection. Pocket sized, nonslip rubber grip and easy to carry.
• Easy to use. Value pack includes: 1 UT210E Pro clamp meter, 1 pair of test leads, 1 paper manual (En), 1 eManual (En), 1 zip bag/black, 1 gift box.
• UNI-T WARRANTY – A trouble-free experience with 100% LIFETIME WARRANTY and 100% MONEY BACK GUARANTEE by UNI-T Direct!

Product features

UNI-T UT210e Pro Digital Clamp Meter

How it works

1. Power. Unscrew rear cover and install 2 batteries (not included).

2. Connect. Insert ground test lead into COM jack. Red test lead into the other.

3. On/Off. Rotate the selection button with your thumb to functions you need.

4. Ready to measure ACV/DCV/frequency, resistance/circuit on-off/diode/capacitance, ac/dc current, NCV noncontact electric field, etc.

More features

Pocket-sized. 6.9”x2.4”x1.3” (175mm x 60mm x 33.5mm). Nonslip rubber grip.

VFC Low Pass Filtering. Reduce disturbance of high-frequency signal and have accurate test results.

NCV. Segmented display of signal strengths for wiring troubleshoots, ie testing null line and firing line separately.

Ac/dc current & small current to mA level. Lessen hidden danger.

True RMS, which is used to determine the power dissipated in a resistor. Measure the "heating" potential of an applied voltage.

Overload protection. Built in smart chip. UT210e Pro is safety rated CAT II 600V, CAT III 300V.

All in one. Diagnose automotive, repair, troubleshoots, industrial and household electrical issues.

Why UNI-T

Main Categories

General Meters, Benchtop Instruments, Layout/Measurement Tools, Environmental Testers, Electrical Power Testers

UNI-T Products

Electronics & electrical, home appliances, electromechanical device, environmental care, rail transit, automobile industry, HVAC (heating, ventilation and air conditioning), construction engineering, building trade, power construction & maintenance, scientific research, surveying & mapping, petroleum mining, network communication, electronics manufacturing, new energy applications, etc.

• ❤【COMPLETE FUNCTIONS & MEET DAILY MEASUREMENT NEEDS】Perfect for all kinds of daily uses and industrial uses can quickly troubleshoot and help repair. With complete functions, such as AC/DC voltage, DC current, resistance, triode test, diode test, transistor hFE test, buzzer function, and continuity measurement. Can be easily used at household outlets, fuses, battery (including vehicles), automotive circuit troubleshooting, charging system, testing electronics in cars, etc.
• 💙【BACKLIGHT DISPLAY & SUPPORT STAND & POCKET SIZE PORTABLE】It can be used easily by experienced electricians or beginners. High resolution and a large backlight LCD screen, which is easy to read in low-light areas. A foldable bracket on the back for hand-free use and makes the screen easy to see, bring more convenience in working. The compact size, complete functions, and lightweight, which is ideal to carry, put it into your toolbox, it won't take up too much space, super practical!
• 💛【OVER-LOAD PROTECTION & INSULATION SILICONE CASE】Built-in explosion-proof ceramic fuse tubes, the fuses can protect the multimeter effectively, which is anti-burn and protects from overloading. A silicone protective sleeve and corner, provide effective protection for the multimeter to prevent accidental dropping and damage. The insulated silicone and plastic shell make the measurement safer. Our electronic multimeter has very high safety, please rest assured to use!
• 💜【VERSATILE CIRCUIT METER & BATTERY TESTER】Provide high degrees of accuracy when measuring the parameters within an electronics or electrical circuit. It is one of the most indispensable pieces of test equipment available, perfect for electrical repair, school department, power electrician, engineering test, public circuit, factory test, original inspection, appliance repair, laboratory, education, factory, workshop, recommended by many professionals engineers.
• 💚【DURABLE & ACCURATE READING】Milky House multimeter is matching equipment, you will get a multimeter, a pair of test leads, a 9V battery, and an instruction manual. The size of the multimeter is 5.71X2.56X1.18in, 226g. Good design& made of high-quality materials, durable& not easy to damage. It is worth mentioning that, our meter was built-in high-precision integrated circuits and smart chips, which can accurately measure. The perfect tool for or DIYers, hobbyists, people that love electronics!

Product features

Troubleshoot Electrical Problems

Milky House multimeter is professionally designed to troubleshoot electrical problems or just for electronics training.

Large digital display with backlit LCD

Large digital display with backlit LCD for easier to read and show the reading clearly in dimly light areas.

Hold the display reading

Hold the display reading. If you want to record the measurement value, just press the 'LED' button, then the reading showed on the screen will be locked.

AC/DC Voltage Test

Battery Test

Resistance Test

Milky House Digital Pocket Multimeter

This Digital Multimeter with Backlight LCD Voltmeter Ohmmeter Ammeter meets your various demands! It is designed to safely and accurately troubleshoot a variety of automotive and household electrical problems.

It's easy and safe to operate for measuring current, voltage, and resistance, as well as continuity, transistor, and diode testing, which is both for automotive and household use and is a basic assistant to test.

Newest design and high quality. Please rest assured to buy!

Features:

Safety Protection Built-in Double fuse

Multi-functional Features

Large LCD Screen

Protective Plastic Sleeve With Bracket

Product description

This combo kit is built around the Fluke 87V, the most widely used industrial digital multimeter in the world, combined with the i400 AC current clamp. Together they provide the resolution and accuracy to efficiently troubleshoot any electrical system. The kit includes special accessories to make you even more productive on the job and will save over 15% compared with the individually priced items. Plus, you'll be working with the most trusted tools in the world.

• Fluke-87v multimeter with temperature frequency, capacitance 250 µs peak min-max
• Fluke-i400 AC 400A current clamp, companion to your DMM to measure upto 400 A AC
• 22 of the most useful accessories for making measurements in low energy, electronic applications
• Specially designed to offer maximum utility in a very compact shape
• Limited lifetime warranty on Fluke-87V and 1-year warranty on accessories

User questions & answers

Question:	Does this Model/ combo kit come with case at included price $599.99+ shipping or I have to pay separately for it
Answer:	NO, Sorry it measures "Brix" the Sugar level in a solution.
Question:	Does this come with a case
Answer:	Obviously the price difference for starters, the milwaukee unit also uses a 9 volt battery versus the latter of AAA. i hjave used the milwaukee unit many times and had very little issues. The only downside to this unit is that you need to keep fresh 9 volt batteries on hand. it does use alot of battery power.

Product features

Fluke 87V Industrial Multimeter

The Fluke 87V Industrial Multimeter provides the resolution and accuracy to efficiently troubleshoot motor drives, plant automation, and electromechanical equipment - even in loud, high-energy, and high-altitude locations. The 87V is designed so you can work more efficiently. The 87V lets you identify complex electrical problems fast. It supports accurate measurements on VFDs using a low-pass filter.

Accuracy

Unique function for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment

Display

Large digital display with bright, two-level backlight makes the 87V significantly easier to read than older models

Applications

Working on VSDs/VFDs: Take accurate voltage, current and frequency measurements on the output side of the drive at either the drive itself or at the motor terminals.

Industrial troubleshooting: All of the resolution and accuracy you need to solve more problems on motor drives, in-plant automation, power distribution, and electro-mechanical equipment.

Checking power quality: Capture glitches and spikes as short as 250 μs. Identify irregular signals.

Accessories

Optional magnetic hanger for easy set-up and viewing while freeing your hands for other tasks