12 best dimmer switch for led lights

• 3-Way Single Pole Compatible Slide control dimmer.If UP is off(DOWN is on) after wiring, try switching around the two red wires to reverse the on/off direction
• Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	Where is it made? USA
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	I doubt it, but contact mfg., they are very responsive.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	Check the display is ON or OFF on the top left connor, it should show ON then the device can work.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	What I think was being asked is if this meter can tell you the PEAK load during the time it was connected. For example, let's say it was connected to a refrigerator for 10 hours. Let's say that during that 10 hours the load in Watts was 150Watts. But, when the compressor kicks in, it surges to 2000Watts for 3 seconds. Will this device allow you to see that 2000Watt PEAK later? Does it store that PEAK load into memory so you can view it?

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Product description

The Leviton toggle slide universal dimmer provides smooth, slide-action, full-range dimming for dimmable LEDs, dimmable CFLs, incandescent and halogen bulbs. For a traditional home, the classic style offers the ideal way to upgrade the functionality without compromising the character of the decor.

• Classic design with toggle switch and integrated linear full-range slide control for easy, precise operation
• Designed specifically for dimmable LED and CFL bulbs; Also compatible with incandescent and halogen bulbs
• Single pole or 3 way capable when used with a 3 way switch. No removal of fins required for multi-gang installations
• Built-in starting technology for CFL bulbs; Allows users to modify the dimming range to optimize low light level performance when required (optional)
• Wider dimming range for LED and CFL bulbs than traditional incandescent dimmers

User questions & answers

Question:	Will this dimmer stand 12 AR111 12Watts each
Answer:	Dimmer will control 300 watt dimmable LEDs if the AR111s you have are dimmable 120V 12Watt lights then switch should be OK as 12 lights would be ~144 Watts
Question:	We were trying to connect this switch, the light is on but the dimmer is not working, its a single pole, what am I missing
Answer:	You need to be using "dimmable" bulbs, either incandescent or LED, but not fluorescent. If you are using dimmable incandescent or LED bulbs, I believe there is a slider control (switch) somewhere on this switch to choose either incandescent or LED. That needs to match your bulb type.
Question:	I installed the switch as well as dimmable led bulbs. they work on the dim setting but they blink from half all the way to full power, any ideas
Answer:	I've had similar issues and took it up with Leviton on their website. They initially just asked me to send it back to them, but I stopped short stating that I didn't particularly want to "finance" that. So they did send me a replacement unit and a prepaid shipping label. The replacement one is "better", but sometimes it still goes into flicker or as I call it "spazz" mode. They have asked me for the exact bulbs I'm using (Ecosmart Classic Glass Bulbs from Home Depot) but nothing further from them. I use those same bulbs in (2) other fixtures with Lutron LED dimmers (Model# TGCL-153PH-WH and Model# CTCL-153PR-WH) and they both have worked flawlessly for about a year. Never a single flicker. Bob
Question:	Where is the locator light
Answer:	Mine has a green LED at the top of the toggle switch. It is almost impossible to see in the light, but when the room is dark, it is visible without being disturbing. It comes defaulted to OFF. There are two micro switches on the front of the switch, which are hidden once that switch plate is put on. The top switch has an A and B position. A (the default) is for LED and incandescent lights. B is for CFC bulbs. A second switch, lower down, is for the locator light. Set the switch to ON if you want to use the light. Set these switches before you put on the switch plate because the plate covers these switches.

Product features

Leviton TSL06-1LW Toggle Slide Universal Dimmer

Leviton’s TSL06 Toggle Slide universal dimmer is engineered to provide homeowners optimal control of 300-watt Dimmable LED and CFL bulbs, and 600-watt Incandescent and Halogen bulbs. This new dimmer offers the energy-saving benefits of dimming without sacrificing performance or the time-honored design valued in traditional homes. The Toggle Slide universal dimmer addresses performance issues–such as flickering, reduced dimming range, and low level start up–often experienced when incandescent-only dimmers are paired with dimmable LED or CFL bulbs.

Great Dimming, Traditional Style

The Toggle Slide universal dimmer features an on/off preset function which preserves the selected dimmer setting, smooth start-up, gentle-touch control, and fluid slide movement for precise dimming. The device’s traditional aesthetics offer the ideal way to upgrade functionality from standard switches without compromising the character of your traditional decor. Its slim, compact housing fits easily into a standard wall box and is suitable for multi-gang installations. The Toggle Slide universal dimmer is compatible with Leviton’s complete line of signature Decora wiring devices and wall plates.

Advanced Features

The Leviton Toggle Slide universal dimmer features a microprocessor control which offers the flexibility to fine-tune LED and CFL bulbs for best performance. A “kick-start” setting is available to ensure start-up of CFL bulbs. The dimmer also features a soft green LED locator light built into the switch, making it easy to find in a dark room.

About Leviton Dimmers

Leviton is a leading manufacturer of dimmers designed for both the energy-saving benefits of dimming and the ambiance that can be created in any room of the home by controlling lighting levels. To ensure superior performance, Leviton works with bulb manufacturers to develop dimmers that are tested and proven effective to function in harmony with the latest bulb innovations. Leviton dimmers come in a wide range of models including digital, wireless, preset, slide, rotary, toggle, and touch and provide precise dependable control.

Product description

Lutron LED+ dimmers provide the best dimming performance for LED bulbswhile setting the right light level to improve mood and ambiance for any activity. Designed specifically for dimmable lads and CFL, as well as for use with traditional incandescent and halogen bulbs, they greatly improve the dimming performance when compared to standard dimmers. Featuring advanced circuitry designed to alleviate common challenges, like flicker and pop on, LED+ dimmers are compatible with 800+ bulbs- for more specific details on compatible bulbs, view "technical specification" below. The Diva dimmer matches existing decor a style switches and fits in a standard decor a style wall plate (CW-1-WH). It features a large paddle switch that turns the lights on/off and returns them to your favorite preset setting, along with a discreet slider that brightens or dims the lights to suit any activity.

Create the perfect amount of light while utilizing the latest energy-saving technology with the Lutron Diva C•L Dimmer. Designed for use with 150-watt dimmable CFL or LED lights, the Lutron Diva C•L dimmer features a large paddle switch that automatically returns to your favorite pre-selected light level, a discreet slider to adjust light levels, and a sleek, modern wallplate.

Diva C•L Dimmer At a Glance: Dimmer works with most dimmable CFL/LED bulbs, as well as incandescent and halogen bulbs Slider for precise light control and paddle switch for easy on/off HED technology improves the performance of dimmable CFLs and LEDs over standard dimmers Adjustment dial to set bottom of dimming range for your bulb type Single-pole and three-way applications One-year limited warranty; UL-listed for a broad range of dimmable CFL/LED bulbs

Adjustment dial fine tunes dimming range for your specific bulb.

The C•L Dimmer works with a combination of CFL, LED, halogen, and incandescent bulbs and can be used on the same circuit.

Precise Light Adjustment with Slider

Whether you're reading, watching TV, entertaining, or enjoying a romantic dinner, the Lutron Diva C•L Dimmer lets you choose the right level of light for your activity. It's easy to make subtle adjustments using the discreet slider next to the large paddle switch. When you use the paddle switch to turn lights off and on, it defaults to your preferred lighting level.

Works with Dimmable CFLs and LEDs for Increased Energy Savings

The Lutron dimmer works with dimmable CFLs and LEDs up to 150 watts, a great energy-efficient alternative that can last up to 10 times longer than incandescent bulbs. Plus, by using less electricity, theses bulbs help protect the environment by reducing the amount of carbon dioxide released into the air.

HED Technology for Enhanced Performance

Thanks to Lutron's HED technology, this dimmer actually improves the performance of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, ensuring lights stay on when they are dimmed to a low level, and making sure lights operate properly at all levels. Lights will stay on even during voltage fluctuations, which can happen when a device like an air conditioner or a hair dryer is operated nearby. For safety, the dimmer is UL listed for a broad range of dimmable CFL and LED bulbs.

Compatible with Other Lightbulbs and Mixed Loads

For added functionality, the dimmer also provides full-range dimming for halogen and incandescent bulbs. There is an adjustment dial to set the low end of dimming range for your bulb type for most efficient operation.

The dimmer also works with a mixed load of light sources, so a combination of CFL, LED, halogen, and incandescent bulbs can be used on the same circuit. It can be used for single-pole and three-way applications.

Fast and Easy Installation

Installation is easy--just replace your existing light switch with the Lutron Diva C•L Dimmer and install in less that 15 minutes. A modern wallplate--with no visible screws--blends into the surrounding wall for a subtle finishing touch.

The Lutron Diva C•L Dimmer is backed by a one-year limited warranty.

What's in the Box

Dimmer and screwless wallplate.

Set the perfect mood lighting for any room with the Diva C•L Dimmer.

From the Manufacturer

Control the next generation of lighting with Lutron's dimmable C.L dimmers! Screw-in dimmable compact fluorescent lamps (CFLs) and screw-in dimmable light emitting diode lamps (LEDs) are a great energy-saving alternative to incandescent or halogen light sources; however, dimming them may be difficult. Lutron's new dimmers with HED Technology provides a solution to alleviate your dimmable CFL and LED dimming challenges, while setting the right light level to improve mood and ambiance. The Diva dimmable CFL/LED dimmer with HED Technology features advanced dimming circuitry that is designed for compatibility with most high efficacy light bulbs. With the same features as Lutron's Diva dimmer, the large paddle switch turns the light on/off and returns to your favorite setting. The discreet slider adjusts the light level to suit any activity. These dimmers improve the dimming performance of dimmable CFLs and LEDs compared to standard dimmers. Lutron dimmers with HED Technology also provide full-range dimming for halogen and incandescent bulbs, ensuring today's dimmer is compatible with tomorrow's light sources. The dimmer can even dim a mixed load of light sources (i.e. LED and halogen or CFL and LED bulbs on the same circuit).

• Provides the best dimming performance for LED bulbs(for list of approved LEDs, see 'Technical Specification' below)
• For use with up to 150-Watts of dimmable LEDs or up to 600-Watts of Incandescent or Halogen bulbs
• Features a large rocker paddle to turn lights on/off or to preset level and a discreet slider to brighten/dim lights to suit any activity
• Can be used in single-pole or 3-way applications
• Installs in as little as 15 minutes. Operating temperatures 32 °F to 104 °F (0 °C to 40 °C)
• Includes Diva LED+ (formerly C.L) Dimmer Switch and coordinating wallplate

Product features

Lutron LED+ Dimmers provide over 250 lighting levels, so you can set the right light for any activity

• Large paddle switch to turn lights ON/OFF
• Sleek slider on the side to manually dim or brighten lights
• Technology that allows for smooth dimming of the broadest range of LEDs
• Patented technology to optimize the dim range of your bulb and prevent interference with other dimmers in the home
• Tried and true aesthetic to match designer/decorator style switches and accessories

Cutting Edge Technology

Our easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Blend In or Stand Out

Available in 25 colors so you can choose a finishing touch to your room that seamlessly blends in or a color that is meant to pop

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

• 3-Way Single Pole Compatible Slide control dimmer.Green indicator turns off when the load is on, turns on when the load if off.
• 600W max Incandescent; 150W max dimmable LED/CFL,120VAC, 60Hz*Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz *Not compatible with smart lighting fixtures
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included, easy to install.
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	With the switch on the dimmer works just fine. with the toggle switch off my led bulbs still glow slightly
Answer:	If you want to turn the light OFF, you must use the switch. The toggle will still give the lights some voltage even in the so called off position.
Question:	With the switch on the dimmer works just fine. with the toggle switch off my led bulbs still glow slightly
Answer:	Good

Product features

Dimmer Switch with Green Indicator

• Voltage: 120V AC
• Single Pole/3 Way installation.(please refer to brief wiring instruction below).
• Fine tune adjustment dial to eliminte LED/CFL flickering.
• No screws needed to fasten wall plate. Looks perfectly blend into the wall.
• Can be used with literally all kinds of your household lighting.
• Dimmer has been tested to be fully compatible with any light fixtures of Cloudy Bay Lighting family, including Cloudy Bay flush mount ceiling lights.
• NOT COMPATIBLE WITH SMART LIGHTS, SUCH AS GE C, PHILIPS HUE WHICH IS CONTROL BY WIFI, BLUE TEETH, ZIGBEE etc.

Compatible with CFL/LED/Incandescent

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Tip: Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

Fine tune with adjustment dial

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a. Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights.

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

• Support single pole or 3-way applications, decor wall plate included. Only one dimmer switch can be installed per 3 way circuit
• LED Dimmer Light Switch: Provides the best dimming performance for LED bulbs. Simple and elegant horizontal slider dims and brightens with ease for full range light control
• Adjuster Dial: Ensures compatibility with almost all dimmable LED, CFL, incandescent and halogen bulbs, up to 150 watts of dimmable LED/CFL lamps or 600 watts of incandescent bulbs
• Smart Rocker: On/Off rocker switch remembers the last dimmed light setting and turns on to that exact light level
• 3 year limited warranty. UL listed

User questions & answers

Question:	does this switch have circuitry does it operate without creating buzzing or humming sound
Answer:	Dear Customer, Thanks for your question about BESTTEN Dimmer Switch. The device will not create buzzing or humming sound. If there are any issues, please feel free to contact us via [email protected] Sincerely BESTTEN Customer
Question:	Do these match your Snow White wall plates
Answer:	Dear Customer, Thanks for your enquriy on BESTTEN dimmer switches. The products match our yellow-white wall plate best. You can refer to the below link: https://www.amazon.com/dp/B07BLXZMBX?ref=myi_title_dp You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	Does this switch stop led blinking
Answer:	Dear Customer, Thanks for your enquriy on BESTTEN Dimmer Light Switch. If your light flicker when it works with this dimner, you can follow the motheds on description or mannual to adjust the adjust wheel to avoid it. You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	I understand that there can only be 1 dim switch in a 3-way setup. Can one of these switches be wired so it is only on/off
Answer:	Your cheaper off putting a standard 3 way for the second switch.

Product features

BESTTEN Modern Dimmer Switch

BESTTEN dimmer switch provides smooth, sliding and full-range dimming performance for dimmable LED, CFL, halogen and incandescent bulbs. The slider can dim and brighten your lights precisely and conveniently, creating a romantic mood or a casual atmosphere for family activities.

• Single pole or 3-way
• No neutral required
• Large ON/OFF rocker paddle switch
• Precise full-range dimming control
• Wide range of compatibility with sensitivity dial
• Wallplate included

Specifications

Voltage.....................................................................................................120V, 60Hz

Dimmable LED/CFL................................................................................Max. 150W

Incandescent/Halogen.............................................................................Max. 600W

Switch Type.............................................................................................Single Pole/3-Way

Wiring Type..............................................................................................Wire Pigtails

Operation Temperature...........................................................................32°F (0°C) --- 104°F (40°C)

Remind:

One circuit can ONLY install one dimmer switch.

Troubleshooting

Symptom:

- Bulbs turn off while being dimmed.

- Bulbs turn on at high light level but do not turn on at a low light level, or take too long to turn on at low end.

- Bulbs flicker or flash when dimmed do a low light level.

- Bulbs or dimmers are buzzing.

Solution:

1. Verify all bulbs are marked dimmable.

2. Remove wallplate and locate sensitivity dial.

3. Turn up (counter-clockwise) sensitivity dial slowly until symptom is no longer present.

• Wall Dimmer Switch with Dimmable Slide: Our Wall Dimmer Switch with Dimmable Slide is compatible with up to 200 Watts of dimmable LED/CFL bulbs and up to 600 Watts of incandescent and halogen lamps. Press the rocker switch of the dimmer, turn power on or off. Move the slide control lever up to increase brightness, move down to decrease brightness. It doesn’t get easier than that! For your safety, this fixture is ETL certified.
• Simple and Easy Installation: This stylish, modern light switch is very easy to install, and mounts just off the wall. It only requires one person to install and can be done in a matter of minutes. Full instructions provided, with decorative wall plate and mounting screws included; 3 Year Limited Warranty against Defects in Materials and Workmanship.
• Best Dimming Performance, Without Flicker: Flickering lights are not only bad for your eyes, they also cause long lasting headaches. If your bulbs do not dim to your satisfaction, especially the dimmer range and minimum brightness level, use the adjustment button of the dimmer after installed for your desired lighting result. This product will help you set the mood and create a nice living environment for your home or office, without buzzing or flickering.
• Single Pole and 3 Way Compatible: This slide control LED dimmer switch can be used in single pole or 3-way applications, making multi-location dimming achievable and satisfying all your requirements.
• Sleek Design: Modernize any space with this cool, contemporary light switch. No screws are needed to mount the wall plate, giving the switch a clean look and smooth finish that allows it to seamlessly blend into its surroundings. The sleek white design is suitable for all internal rooms such as kitchen, lounge and bedrooms, as well as business environments such as restaurants, bars, cafes and all office spaces.

• Support single pole or 3-way applications, decor wall plate included. Only one dimmer switch can be installed per 3 way circuit
• LED Dimmer Light Switch: Provides the best dimming performance for LED bulbs. Simple and elegant horizontal slider dims and brightens with ease for full range light control
• Adjuster Dial: Ensures compatibility with almost all dimmable LED, CFL, incandescent and halogen bulbs, up to 150 watts of dimmable LED/CFL lamps or 600 watts of incandescent bulbs
• Smart Rocker: On/Off rocker switch remembers the last dimmed light setting and turns on to that exact light level
• 3 year warranty. UL listed. NOTE: The dimming range of dimmable LEDs may vary from manufacturer to manufacturer. This dimmer has an adjustable dimming range. Please rotate the side adjustment wheel to eliminate flicker issues

User questions & answers

Question:	are these ul listed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. Yes, they are UL listed. You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	I am replacing incandescent dimmer switches these led switches are 2.12 inches wide. my existing switches are 1.75 inches wide. can they be trimmed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. The side tabs can be removed which will reduce the width to 1.75in. Any other question, please contact us via [email protected] or call 800-358-6160. BESTTEN Customer Care
Question:	Do they come in light almond
Answer:	Don't think so.
Question:	Can we use these dimmers with leds that requires 0-10v dimming control (driver) 120-277v
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN dimmer light switch. Yes, it can install in a 120v circuit and control a 0-10v dimmable LED lights. BESTTEN Customer Care [email protected]

Product features

BESTTEN Modern Dimmer Switch

BESTTEN dimmer switch provides smooth, sliding and full-range dimming performance for dimmable LED, CFL, halogen and incandescent bulbs. The slider can dim and brighten your lights precisely and conveniently, creating a romantic mood or a casual atmosphere for family activities.

• Single pole or 3-way
• No neutral required
• Large ON/OFF rocker paddle switch
• Precise full-range dimming control
• Wide range of compatibility with sensitivity dial
• Wallplate included

Specifications

Voltage.....................................................................................................120V, 60Hz

Dimmable LED/CFL................................................................................Max. 150W

Incandescent/Halogen.............................................................................Max. 600W

Switch Type.............................................................................................Single Pole/3-Way

Wiring Type..............................................................................................Wire Pigtails

Operation Temperature...........................................................................32°F (0°C) --- 104°F (40°C)

Remind:

One circuit can ONLY install one dimmer switch.

Troubleshooting

Symptom:

- Bulbs turn off while being dimmed.

- Bulbs turn on at high light level but do not turn on at a low light level, or take too long to turn on at low end.

- Bulbs flicker or flash when dimmed do a low light level.

- Bulbs or dimmers are buzzing.

Solution:

1. Verify all bulbs are marked dimmable.

2. Remove wallplate and locate sensitivity dial.

3. Turn up (counter-clockwise) sensitivity dial slowly until symptom is no longer present.

• 0% - 100% Dimmable - Adjust the desired brightness/speed via phone app, voice control, or manually via the LED touch panel. Brightness memory function is available for the last light setting when powered off. Supports up to 150W dimmable LED/CFL or 400W incandescent bulbs and 100W ceiling fans. Smart bulb can’t be dimmed by the smart dimmer switch.
• Voice Control - The dimmer smart switch works with Alexa & Google Home Assistant to free your hands; No Hub or subscription required. Enable the Gosund skill in the Alexa/Google app to pair.
• Remote Control & Scheduling - Remote control your smart switch dimmer from anywhere via Gosund App; set schedules to turn on/off electrical appliances while you are home or away. You can also share the App with your family members to control device. 2.4G WiFi only for the first time installation (NOT 5G); single-pole use only (NOT 3-way).
• Group & Scene Control - Group control your Gosund smart dimmer light switches; create scenes for when you wake up, go to bed and so on.
• Note: Neutral Wire is needed; Step-by-step instructions will guide you through the wiring process. Standard size fits any standard multi-gang wall plate.

Product features

Gosund Wifi Smart Dimmer Switch

Smooth Touch Sensor: Just softly slide up/ down your finger to adjust light brightness or fan speed on the WiFi dimmer switch.

Smart Dimming: To create your ambiance - simply set the brightness of lights, schedules, or group with other devices in Gosund smart scenes. Gosund smart app makes it possible to monitor and control your wifi dimmer from anywhere.

Safety and Durability: Flammability UL94-V0 fire-resistant material ensures overload protection.Gosund 2-years product support is provided.

Touch Dimming Elegant Design

Gosund smart light dimmer switch has an elegant touch dimming interface that looks beautiful on the wall.

Equipped with sensitive touch panel, simply touch slide your finger on the panel to adjust the brightness of multiple light bulbs or the fan speed on Gosund dimmer light switch.

100% Dimming Range

Adjust brightness from 0 –100% to cut energy costs and extend bulbs life. Set the perfect ambiance light for any activities.

You can create scenes with the desired brightness when having dinner with your family, watching movies, or reading a book.

Gosund dimmer switch also remembers the light setting even after a power interruption.

Light Compatibility

The smart switch supports up to 150W dimmable LED/CFL or 400W incandescent bulbs and 100W ceiling fans. Smart bulb can’t be dimmed by the smart dimmer switch.

Remote Control and Share Device

Dim the lights or control the fan speed by a simple tap on Gosund app anywhere and anytime.

Share the smart controls with your family members or roommates via the" share device" function, so they don't need to reconfigure the wifi light switch, make it easier to spread fun and convenience of smart home controls.

Brightness Memory

Gosund dimmable smart switch turns on with the same brightness/speed level as when you last turned it off, so your eyes keeps comfort from too bright light.

Voice Control with Alexa, Google Assistant

Set lighting levels using voice control with an Amazon Alexa, Google Assistant. You can also create a group for all your smart plugs, smart bulbs and smart switches ,then control them all with one voice command.

Scheduling and Smart Scenes

Set up Gosund dimmer light switch to turn on and off based on your daily schedules and preferences.

With the smart dimmer switch, you can create your personalized smart scenes to adjust your home lighting automatically to sunset and sunrise times.

The smart light switch can also help trick potential intruders by switching lights on and off when you are on vacation or away from home that improves home security.

Group Control and Home Automation

Group your smart led dimmer switch with other Gosund smart devices to make your home automation complete.

Gosund app supports setting smart plugs, smart strip lights and other smart devices in the same group, gives you the ability to control all the smart devices at once. You can also set a schedule for all smart switches to turn on and off automatically.

Gosund App Connection Steps:

• Step 1： Search "Gosund" on App store, Google Play or Scan the QR code on the user manual to download and install it.
• Step 2：Power on wifi dimmer switch and long press ON/OFF Button in pair mode. Note: The blinking green light of the switch shows the wifi switch is ready for wifi-connection.
• Step 3：Add Device> smart dimmer switch(Wi-Fi) and confirm the device in the App, and connect the switch to your local 2.4GHz network with your phone.

Safety and Certificates

• V0 fire resistant
• UV resistant- No aging and yellowing on switch housing after many years.
• PC + ABS material for overload protection
• FCC, CUL certificated

Product description

Wi-Fi Enabled Smart Dimmer Switch with brightness control. Note1: Requires neutral wiring. If no neutral wire is present, the installation cannot be completed. Note2: Works in single pole wiring only. Note3: Requires a secured 2.4 GHz wireless home connection. Please consult a professional electrician if you are unfamiliar with basic electrical wiring.

• Control from anywhere: Turn electronics on or off from anywhere with your smartphone using the case app (Compatible w/ Android & iOS)
• Voice Control - Works with Amazon Alexa, Google Assistant and Microsoft Cortana supported devices for a hands-free experience
• Gentle off - Tailor your lighting to fade on with a click of the switch or a double-click to gently fade off the lights while your child drifts off to sleep
• Scheduling - Use Schedules to set your smart switch to automatically turn on and off while you're home or away
• Note: Requires a neutral wire / Works in a single-pole setup only / Secured 2.4 GHz WiFi network connection

Product features

Start Dimming

The Kasa Smart app guides you through each step of the wiring process and helps you connect to your home Wi-Fi. You can control the brightness of lights, set schedules, or include with other devices in Kasa lighting scenes to set the perfect ambiance. The Kasa Smart app gives you the ability to monitor and control your smart dimmer from anywhere.

What is a neutral wire?

A neutral wire allows Kasa switch to be powered while simultaneously allowing the lighting circuit connected to your lights to be power off.

Control Your Dimmer from Anywhere

With the Smart Wi-Fi Dimmer, you can control the ambiance of any space with the push of a button. Plus, easily control it from anywhere using the Kasa app or your favorite voice assistant device.

Gentle Off

Use 'Gentle Off' to fade off the lights in your child's bedroom as they drift off to sleep or allow yourself time to exit a room without bumping into something in the dark.

Brightness Control

Control the brightness of lights in any room and set the ambiance for any activity. Designed to dim today's energy efficient LEDs as well as traditional incandescent bulbs.

Scheduling

Use 'Schedules' to set your smart dimmer switch to automatically turn on and off while you're home or away. With IFTTT or Nest, you can set your device to turn on and off depending on your location.

Set Scenes

Group your smart dimmer switch with other Kasa devices to create 'Scenes'. Have it be a part of a scene for when you wake up, go to bed, or one to make it look like you're home even if you aren't.

Control with Your Voice

Set lighting levels using voice control with an Amazon Alexa, Google Assistant or Microsoft Cortana supported device.

Your Home. One App.

The Kasa app works with all TP-Link smart home devices, allowing easy control of your home from your Android or iOS smartphone.

No Hub Required

The Smart Dimmer connects to your secured 2.4 GHz Wi-Fi network. No need for a separate smart home hub.

Product description

Lutron Ariadni dimmers are a simple and inexpensive way to add ambiance to any room in your home, while saving energy and extending bulbs life. This dimmer is designed to replace or match your traditional toggle style switches. The discreet slider next to the toggle switch adjusts the brightness of the bulbs to a desired level, while the toggle switch turns the light off and on to your favorite preset level. Designed with a shallow 1 inch deep back cover for easy installation, Ariadni and Toggler dimmers work with your existing traditional opening wall plates. Coordinating Facade screw less wall plates and accessories sold separately.

• Provides the best dimming performance for LED bulbs(compatible with 800+ bulbs- for more specific details view "technical specification" below)
• Also works with ALL incandescent and halogen bulbs
• Works with up to 150 Watts of dimmable LED/CFL bulbs or 600 Watts of Incandescent/Halogen bulbs
• Can be used in Single-Pole or 3-Way applications
• Toggle switch turns lights on/off and returns light to preset level, slider dims and brightens
• Includes Lutron Toggler LED+ (formerly C.L) Dimmer Switch; coordinating wallplate sold separately

User questions & answers

Question:	Is this considered triac based (forward phase control or leading edge) or 0-10v switch
Answer:	The AYCL-153P is a triac based dimmer rated for 150W of compatible LED/CFL or 600W of incandescent/halogen lighting. For compatible LEDs with this dimmer, or another Lutron dimmer, please visit www.lutron.com/ledfinder or www.lutron.com/ledtool.
Question:	do I need two of these switches in a 3-way application or can I use one dimmer with a normal 3-way on the other end
Answer:	Lutron does not recommend two AYCL-153P-WH dimmers in 3-way application. The second location would need to be a standard 3-way mechanical switch.
Question:	Can you fit three of these switches side by side in a standard 3 gang box
Answer:	The switch generates heat so it has tabs on both sides to prevent you from mounting them side by side without being aware that you have to "derate" them if you want to install them side be side. In other words, you can put 600 watts of incandescent bulbs on one dimmer if you mount it alone but only 500 watts of incandescent on a dimmer with one side tab removed (you remove only the tab(s) that overlap) and only 400 watts load with both tabs removed (as you would do mounting 3 switches in a standard 3 gang box). They also include a chart for derating when you mix CFL/LED bulbs with incandescent.
Question:	Anyone know the difference between the "Ariadni" switch (AYCL-153P) and the "Toggler" switch (TGCL-153P
Answer:	I was wondering this exact same question, so I called Lutron and learned that they're the exact same switch. The model numbers differ because they're marketed/sold differently (e.g. Home Depot vs. other stores). So, if you find one cheaper than another, as I've done here on Amazon, buy the less expensive one!
Question:	Where is it made? USA
Answer:	HI，Customer， It is Made in China, UL listed
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	Yes, these are standard size switches. Home Depot or Lowes should have multi-gang plates.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	I doubt it, but contact mfg., they are very responsive.

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Cutting Edge Technology

Our patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Fast and Easy Installation

All you need to replace your existing switch or dimmer is about 15 minutes, 3 simple steps and 1 screwdriver

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

• Best Dimming Performance- Full range dimming and enable light brightness dimming from 0% to 100%. It's ideal for applications requiring low voltage, such as LED drivers, fluorescent ballasts, panel lights, and other fixtures installed in commercial offices, conference rooms and shopping malls. [Some LED lights which are not 100% compatible, may not be available for full dimming range.]
• Widely Applicable- Ensures compatibility for most types of dimmable LED devices.For use with up to 150 Watts of dimmable LED/CFL and up to 600 Watts of incandescent and halogen lamps. You will have fabulous dimming performance without having to deal with buzzing or flickering.
• Single pole/3-Way Switch- This slide LED dimmer switch can be used in single pole or 3-way applications, making multi-location dimming achievable and satisfying all your requirements.
• Easy Installation- Features a large rocker paddle to turn lights on/off or to preset level and a fluent slider to brighten/dim lights to suit different activities. Single Pole & 3-way LED Dimmer, AC 120V 50~60Hz input.
• Support Guarantee- Enjoy a 2-YEAR WARRANTY, free lifetime technical support. [Package included 2-Pack Wall Switch and coordinating wall plate.]

Product features

RGBZONE Single Pole/3-Way Dimmer Switch

It's a wall light switch and also a dimmer. This 3-way LED dimmer provides optimal dimming performance of LED bulbs.

● Easily turn the lights on and off with a paddle switch, and use the fluent slide control to adjust the lights to the perfect level.

● It can be used for single-pole and three-way applications.

● One circuit can ONLY install one dimmer switch.

Works with Dimmable LED/CFL/Incandescent/ Halogen

This dimmer switch works with up to 150 Watts of dimmable LED/CFL or 600 Watts of incandescent/ halogen, allowing you to control multiple bulb types on the same circuit. It is designed to control most dimmable LED and CFL bulbs brands including GE, Philips, EcoSmart, Cree and others.

Large Paddle Switch to Turn Lights ON/OFF

The LED dimmer is a paddle switch to turn your lights off or on. Simple and modern design makes it convenient for your daily life.

[NOT for Ceiling Fan with LED Lights]

Slider Dimming 0% - 100% Brightness

This dimmer also features a discreet slide control next to the switch, allowing you to adjust the lights for any activities.

[Some LED lights which are not 100% compatible, may not be available for full dimming range.]

Widely Used Decor Wall Switch

A modern wallplate blends into the surrounding wall for a subtle finishing touch. It can be used for single-pole and three-way applications. Ideal for Kitchen, dining room, living room, bedroom, garage, office, cafe, hotel etc.

How to do the wire connection?

Single Pole:

Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer.

3-Way:

Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch.

Trouble Shooting

Here're some tips:

Product description

Bring technology and style to your home with the Lutron Maestro C×L Dimmer, the first digital dimmer that is compatible with all of today's bulbs types dimmable CFL and LED, halogen, and incandescent. This digital dimmer gradually turns lights on and off, allowing your eyes to adjust to the new light level. LED's display the light level and glow softly in the dark, acting as a locator light so you can easily find the control in the dark. Use the rocker to adjust the light level for any activity or set the preset level to ensure lights always turn on to your desired light level. Advanced features include delayed fade to off, which allows time to exit a room or to get into bed before the lights turn off. Installing the Maestro C·L is simple and quick, and is perfect for any room in the home. It also coordinates with the entire Maestro family of controls including dimmers, switches, occupancy sensors, and more. Coordinating Claro wall plate is not included.

• Tested on 1,000s of bulbs and dozens of brands for flicker-free dimming. For list of recommended bulbs view "Technical Specification" below
• Provides over 250 lighting levels so you can create the perfect light for any activity
• Works with up to 150 Watts of dimmable LED/CFL bulbsor 600 Watts of Incandescent/Halogen bulbs For list of recommended bulbs, view "Technical Specification" below
• Lutron patented technology to optimize the dim range of your bulbs and prevent interference with other dimmers in the home
• Can be used in single-pole or 3-Way/multi-location dimming applications (up to 10 locations, Maestro companion dimmer MA-RR-XX required)

User questions & answers

Question:	Is anyone using this with an LED and if so, for how long and how is it working? Thanks
Answer:	I'm using this with two 12.5W Soraa High-CRI "Vivid" series LED PAR30 4000K bulbs (total controlled load: 25W) and it is the finest dimmer switch I've ever used. With the "Advanced mode" custom programming (Technical document: www.lutron.com/TechnicalDocumentLibrary/048459.pdf) to adjust the "low trim" (dimmest point) I can get these bulbs to be on and stable at only
Question:	Can this handle dimming LED lights all the way down so they are actually dim, like the incandescents? Yes, I have an LED light bulb that is dimmable
Answer:	I have the Wafer 6 in. White Integrated LED Recessed Kit that Home Depot sells. They say they can go down to 10%.. I had another switch in previously that the lights wouldn't dim down as far and would turn off randomly when dimmed down all the way. If you use the adjustment feature in this switch it seems like they go down to that no problem. I've been running them for a day and no flickering or turning off. If anything changes I'll leave an updated comment or update this answer. Two factors you'll need to look at: 1) what is the LED bulb rated to go down to 2) Is this dimmer compatible? If your LED bulb says it can do it try many different dimmers until one works :)
Question:	The max brightness seems lower than when I had a non-digital dimmer. How do I adjust? I see instructions for the lower dim range but not the max
Answer:	Please see Lutron's Application Note #459. All of these settings are NOT listed in the manual that came with your switch. www.lutron.com/TechnicalDocumentLibrary/048459.pdf You want to adjust IL7, the high-end trim.IL1: Preset Light Level (last setting or set permanently)IL2: Fade ON Time (0.75 to 15.0 seconds)IL3: Fade OFF Time (0.75 to 15.0 seconds)IL4: Delayed Fade to OFF (time to leave the room - 10 to 70 seconds)IL5: Enable/Disable Indicator Lights (LED dots off or on)IL6: Low-End Trim (minimum brightness)IL7: High-End Trim (maximum brightness)
Question:	how much power do led indicator lights draw
Answer:	Approximately 0.02 Watts (2 cents per year at $0.10/kWh) if they did the job right of designing it (switching converter,) and 0.25 Watts (20 cents per year at $0.10/kWh) if they took the lazy way out (simple resistor.)

Product features

Cutting Edge Technology

Our patented easy-to-set adjuster via button press programming allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control Up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs and is the only dimmer UL listed to control mixed loads (different types of bulbs on the same circuit).

Blend in or Stand Out

Available in 25 colors so you can choose a finishing touch to your room that seamlessly blends in or a color that is meant to pop.

Works Well with LEDs

Tested on 1,000s of bulbs and dozens of brands to ensure flawless dimming. Check out the Lutron website for our list of recommended bulbs.