13 best car jack stands

Product description

Pro lift T-6903D is a 3-ton double locking jack stands. It features a high quality cast ductile Iron Ratchet bar and sturdy stamped steel base provide durability and longevity which makes ideal for home, professional and farm use. Always used in pairs, counter weighted pawls serve as a safe secure locking device to prevent the load from accidental disengagement. An attached pin lock provides support, locking the ratchet bar in place for an additional carrying point. One piece, multi position ductile ratchet bar provides strength and durability as well as a quick adjustment mechanism that securely locks into the desired position.

• Sturdy stamped Steel Construction with 3 ton capacity
• High quality cast ductile iron ratchet bar
• Double locks mechanism with both handle locks and mobility pin
• Height adjustment mechanism allows smooth upward movement while release handle locks and mobility pin
• Meets or exceeds ANSI/PALD standards. Ideal for home, Auto, truck service, farm, and shop use
• Fit type: Universal Fit

User questions & answers

Question:	Where can I buy just the locking pin
Answer:	Max 16 1/2 min 11 inches
Question:	what is the extended maximum height
Answer:	It mounts to the Smittybilt Pivot hinge, so it will clear most aftermarket bumpers as long as they don’t have an integrated tire carrier.
Question:	Does it come with 2 or just one jack
Answer:	No
Question:	What are the max and min lift dimensions
Answer:	I use an insulator for the handle but the mount is very secure and makes little to no noise compared to my old one.

Product features

Pro-Lift Double Pin Jack Stands - 3 Ton

Features:

• Sturdy stamped steel construction
• High quality cast ductile iron ratchet bar
• Height adjustment mechanism allows smooth upward movement while release handle locks into position
• Ideal for auto, truck service, farm and shop use

Product description

Performance Tool W41022 3 Ton Jack Stands are ratcheting for easy adjustment, with a 12 inch to 17 and 1/4 inch range.

• Rated capacity: 3 Ton (6000 pounds)
• Lift Range: 11-1/4” to 16-3/4”
• Heavy duty construction with sturdy/durable steel frame and a wide base to provide strength and stability under load
• 2 heavy duty steel jack stands at one low price
• Great for cars and light duty trucks

User questions & answers

Question:	For the 3 ton jack: all the descriptions show it to be a 3 ton jack but the title says it's a "cooling system pressure tester kit
Answer:	The title is in error. I purchased the Wilmar W41022 3 ton jack stand which is what the description shows and is what the title should read. If you click "Add to cart" then go to the cart, then you will see the title is correct for the jack stands. That said I have been very satisfied with these stands. Recommend.
Question:	Is this 3 tons each stand = to total of 6 ton or is each stand 6 tons = to 12 total
Answer:	Just like it states, SIX TONS EACH=12 total (a ton is 2,000 pounds; 6 tons is 12,000 pounds).
Question:	What is the base dimension please? How wide is the base please? Thank you for your time
Answer:	Approx 8"
Question:	Where are these jacks manufactured
Answer:	The jack stands are made in China.

Product description

The Torin AT43002AB steel double locking jack stands are a must have necessity in any garage. Handles a wide range of vehicles including small cars, jeeps, ATV's, UTV's, and more. It's constructed of high-grade steel with a welded frame for quality and long term durability. Features a lifting range of 11-1/4" to 16-3/4" with a 3 ton (6,000 lb) load capacity. Each stand is equipped with a removable locking support pin designed and dedicated to keeping you safe and increases safety by 200%. Multi-position forged iron ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place. The saddle has a large surface area that provides better contact with the load being supported. Wide pyramid style foot base provides added strength; Large foot base delivers additional stability and measures 7-11/16" x 6-7/8". Meets ASME safety standards and includes a limited 1 year manufacturer warranty.

• Double locking jack stands help support vehicles after lifting with a jack; Handles a wide range of vehicles including small cars, jeeps, ATV's, UTV's, and more
• Features a lifting range of 11-1/4" to 16-3/4" with a 3 ton (6,000 lb) load capacity; Saddle has a large surface area that provides better contact with the load being supported
• Constructed with heavy-duty steel and is industrial welded for quality and long term durability; Removable locking support pin provides added security that increases safety by 200%
• Wide pyramid style foot base provides added strength; Large foot base delivers additional stability and measures 7-11/16" x 6-7/8"
• Multi-position forged iron ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place; Meets ASME safety standards and includes a limited 1 year manufacturer warranty

User questions & answers

Question:	Does this include 2 stands
Answer:	One set is 2 stands... I bought 2 sets because I needed four of them..

Product description

Pro lift T-6906D is a 6-ton double locking jack stands. It features a high quality cast ductile Iron Ratchet bar and sturdy stamped steel base provide durability and longevity which makes ideal for home, professional and farm use. Always used in pairs, counter weighted pawls serve as a safe secure locking device to prevent the load from accidental disengagement. An attached pin lock provides support, locking the ratchet bar in place for an additional carrying point. One piece, multi position ductile ratchet bar provides strength and durability as well as a quick adjustment mechanism that securely locks into the desired position.

• Sturdy stamped Steel Construction with 6 ton capacity
• High quality cast ductile iron ratchet bar
• Double locks mechanism with both handle locks and mobility pin
• Height adjustment mechanism allows smooth upward movement while release handle locks and mobility pin
• Meets or exceeds ANSI/PALD standards. Ideal for home, Auto, truck service, farm, and shop use
• Comes with 2 Adjustable Beam and a Single stand;It has both commercial and residential applications

User questions & answers

Question:	Is the pin attached to the back so it doesn't get lost
Answer:	I took some measurements for you. Base weight 8.6 pounds Tongue weight 4.8 pounds Weight per stand 13.4 pounds each Total weight per set of 2 jack stands 26.8 pounds Tongue head contact size 1 inch x 3-31/32 inches Number of notches in tongue 11 Distance between notches in tongue: 3/4 inch steps Base stand dimensions 9 inches x 10-3/8 inches All height measurements are from floor to lowest U shaped contact point in tongue head (true resting point) Minimum lift height tongue base resting on floor: 14-3/16 inches Minimum height to first notch (non locking): 15-7/16 inches Minimum height to first locking notch: 16-1/8 inches Maximum lift height (locking) 22-7/8 inches. Note the lift is a little higher if you add the top of the saddle points, that is if the object is not resting in the U shaped saddle but at the top of the crown-ridges Weld quality-good/acceptable box and packing o.k. capacity as stated in literature: 6 tons per pair Country of manufacture: China Based on the above, I bought a second set, as I liked the first set.
Question:	Are these 6 tons each or 2 three ton stands that equal 6 tons
Answer:	Lifting range is 6-3/8" to 22".
Question:	How high they can extend and hold
Answer:	china
Question:	Please add some more info to your listing. What's the minimum and maximum clearance? What are the dimensions on the heads? Base
Answer:	These jacks will hold 3 tons or 6,000 pounds. Since you won’t be holding the entire weight of your vehicle you should be fine. These are great light weight jacks for tire changes and auto maintenance too.

Product features

Pro-LifT Double Pin Jack

Pin style jack stands offer the ultimate in security and safety. All Black-hawk Automotive pin style stands are offer some of the best values on the market today.

• Sturdy stamped steel construction
• Height adjustment mechanism allows smooth upward movement while release handle locks into position
• Ideal for auto, truck service, farm, and shop use

Product description

The Torin BIG RED T43002A steel double locking jack stands are a must have necessity in any garage. Handles a wide range of vehicles including small cars, jeeps, ATV's, UTV's, and more. It's constructed of high-grade steel with a welded frame for quality and long term durability. Features a lifting range of 11-1/4" to 16-3/4" with a 3 ton (6,000 lb) load capacity. Each stand is equipped with a removable locking support pin designed and dedicated to keeping you safe and increases safety by 200%. Multi-position forged iron ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place. The saddle has a large surface area that provides better contact with the load being supported. Wide pyramid style foot base provides added strength; Large foot base delivers additional stability and measures 7-11/16" x 6-7/8". Meets ASME safety standards and includes a limited 1 year manufacturer warranty.

• Double locking jack stands help support vehicles after lifting with a jack; Handles a wide range of vehicles including small cars, jeeps, ATV's, UTV's, and more
• Features a lifting range of 11-1/4" to 16-3/4" with a 3 ton (6,000 lb) load capacity; Saddle has a large surface area that provides better contact with the load being supported.Saddle Diameter:3.35 inch
• Constructed with heavy-duty steel and is industrial welded for quality and long term durability; Removable locking support pin provides added security that increases safety by 200%
• Wide pyramid style foot base provides added strength; Large foot base delivers additional stability and measures 7-11/16" x 6-7/8"
• Multi-position forged iron ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place; Meets ASME safety standards and includes a limited 1 year manufacturer warranty

User questions & answers

Question:	How much does a single jack hold? 3000 lbs? Or is it 3000 lbs per pair
Answer:	Im not sure of the Max height but they go high enough to list a suburban and get wheels off. I just used them this weekend for brake job. I would do a search in google to find the max height, they also make some stands that are meant for SUVs which go higher. If you need to get a transmission out or something like that these wont go high enough.
Question:	What are the min and max height for these please? What are the base outside dimensions please? Thanks
Answer:	Hi, friend, yes, it could work with Maserati ghibli Q s 2015 as long as it has OBD2 data connection( without encryption) Hope my answer is help for you. Feel free to contact us any time if you need. Thanks.
Question:	Anyone know the difference t43002 and t43002a? the former is $10 cheaper, but description identical to this one
Answer:	Dear customer, thank you for your question, yes, we offer online lifetime update for TryAce SR950, The website is http://www.itoscanner.com/download/, or you could find it on every manual. So you could buy with confidence. If you have any other questions, feel free to contact us any time, we will give you reply soon. Thanks.
Question:	how high do they go
Answer:	It will work for all Honda vehicles, 1995 and above of course.

Product features

Torin BIG RED Steel Jack Stands: Double Locking, 3 Ton (6,000 lb) Capacity, Red, 1 Pair

Product description

The Torin BIG RED T43202 lightweight jack stands are used to support your vehicle after lifting with a jack. Constructed of high-grade forged steel with a welded frame design for durability, it handles a wide range of vehicles including small cars, SUVs, and light duty trucks. Adjustable height ranges from 11-1/4" to 16-3/4" with a 3 ton (6,000 lb) load capacity. Multi-position ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place. It features a large saddle surface area for better contact with the load being supported. A wide pyramid foot base provides added strength and stable support. Tested for reliability and safety to meet ASME standards. Includes a limited 1 year manufacturer warranty.

• Lightweight jack stands are used to support your vehicle after lifting with a jack; Wide pyramid foot base provides added strength and stable support
• Constructed of high-grade forged steel with a welded frame design for durability, it handles a wide range of vehicles including small cars, SUVs, and light duty trucks
• Adjustable height ranges from 11-1/4" to 16-3/4" with a 3 ton (6,000 lb) load capacity
• Multi-position ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place
• Features a large saddle surface area for better contact with the load being supported; Tested for reliability and safety to meet ASME standards

User questions & answers

Question:	hi, where are these made in? thanks
Answer:	Torin Big Red Steel Jacks are made in China.
Question:	Will these lift a car high enough to change tranny fluid? Any benefit to going with the 3 Ton over 2 Ton for a regular sized car
Answer:	Yes, a higher tonnage jack stand will be more stable and in many cases provide a higher lift range. At the same time you need to know the minimum lift height the vehicles you're working on will need but this is more a matter of the jack not the stand. Any decent jack will lift high enough for a 3 ton stand unless it's an odd spot on a lifted (SUV or truck) vehicle. I would say go for the 3 ton for a regular sized car or small crossover. Remember that 3 ton capacity is a rating for the PAIR of stands, not per stand.
Question:	what is the height at the lowest and tallest
Answer:	Lowest 18 3/16 highest 28 1/2
Question:	What dimensions can you give like min hight
Answer:	its like almost a foot tall maybe 11 inches

Product features

Torin BIG RED Steel Jack Stands: 3 Ton (6,000 lb) Capacity, 1 Pair

• Lightweight jack stand used to support your vehicle after lifting with a jack
• Adjustable height ranges from 11-1/4" to 16-3/4" with a 3 ton (6,000 lb) load capacity
• Constructed of high-grade forged steel with a welded frame design for durability
• Large saddle surface area for better contact with the load being supported
• Meets ASME safety standards

Sawtooth Ratchet Bar

Multi-position ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place

Dual Purpose Handle

Dual purpose handle serves as carry handle and saddle column release

Large Concave Saddle

Designed with a large, concave saddle for better contact and load support

Wide Pyramid Base

Wide pyramid foot base provides added strength and stable support

Product description

Cartman 3 Ton Jack Stand features a double locking pawl and tooth design for extra protection. The one piece multi-position ductile ratchet bar provides super strength and durability. The quick adjustment mechanism securely locks it into the desired location providing extra safety.

• 2 heavy duty steel jack stands at one low price
• Meets or exceeds ANSI requirements
• 278mm - 415mm
• One piece multi position ductile ratchet bar
• Quick adjustment mechanism

User questions & answers

Question:	Where are these stands made? are they pictures of the welding on the stands
Answer:	Mine were welded OK I'm sure PRC unfortunately.
Question:	what is the min & maxlift heights
Answer:	as mentioned on web: 278mm - 415mm
Question:	Is delivery fast
Answer:	Yes.
Question:	Are these compatible to use with jack pads
Answer:	Yes, order according to the size of the stand.

Product description

Fit Under Low Ground Clearance Vehicle

Pro-Lift F-767 Grey Low Profile Floor Jack is a 2 Ton floor jack that give you better access to low ground clearance vehicle. And,give you the lifting range from 3-1/2 inches to 14 inches.

The Jack can be fit under a clearance of 3-1/2 inches and maneuvered easily into position.

Pro Lift F-767 floor jack also features the heavy duty steel construction that provides the long lasting durability.

Pro Lift unique patented bypass device protects against over pumping. Its built-in safety valve provides overload protection.

- Extra Low Profile

- Lifting Range from 3-1/2 inches to 14 inches

- Patented bypass device protect over pumping

- Built-In Safty Valve Provides overload protection

Pro Lift F-767 floor jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Take one now to access to the areas you never access before.

• Extra low profile
• Lifting range of 3-1/2 inches to 14 inches
• Patented bypass device protects against over pumping for safe operations
• Built-in safety valve provides overload protection. Rust Resistant
• Heavy duty steel construction provides long term durability

User questions & answers

Question:	Does it come with a portable case
Answer:	No, but the box it comes in is pretty sturdy. If you remove the cardboard packing the jack easily slides back into the box. The inside bottom of the box is reinforced. Not sure how long it will hold up, but it’s better than nothing.
Question:	Will this raise a 2011 cadillac cts enough to get jack stands underneath it? i want to change transmission oil ... thanks
Answer:	A Cadillac CTS is roughly 4,300 pounds. Which is a little over the capacity of this jack. As long as you're placing it on jack stands and you don't leave the jack holding it too long, it should be okay. Although all the armchair experts on this site will implore you to buy a 3 or 4 ton jack. Just remember to always put the car on jack stands and do your work on a flat, level surface.
Question:	Can anyone tell me the outside diameter of the lifting cup? Thanks
Answer:	The cup itself is 2 1/4 inches, with the inner portion (The part that spins freely, with the 4 tabs) 1 7/8ths, and the tabs extend about 1/4 inch up from the cup. Hope this helps.
Question:	What kind of oil does this take? The screw was loose when it was shipped to me and some oil had poured out into the box. I just want to top it off
Answer:	hydraulic jack oil. The screw IS loose upon arrival. If you read the SHORT instructions....this (grey) screw is HOW TO LOWER the jack when you are done lifting and have supported the weight/vehicle with jack stands. Turning just a bit using the handle you used to pump up the vehicle - you will notice it lower ever so gently. ONCE it is fully lowered - it is best to immediately turn the screw clockwise until it stops - this prepares the jack for its next use. Do this so you will not forget it is closed. IMO - some people with oil spewing - did not 'get it' how important it is to assure the valve is closed BEFORE raising the vehicle.

Product features

Pro-Lift F-767 Grey Low Profile Floor Jack - 2 Ton Capacity

About Us:

Our ProLift hydraulic automotive jacks, lifts and garage equipment range will cater to many 'do it yourself' enthusiast. The product line includes bottle jacks, floor jacks, garage jacks, aluminum jacks. scissor jack, lawn mower lifts, utility lifts, chokes, dirt bike lift, creepers, mechanic seats and more! Explore our range on the products page.

ProLift has become a global presence in the go to automotive garage maintenance equipment with locations in the United States, The Netherlands, Taiwan and Australia. We create dependable and reliable performance hydraulic equipment.

• [HEAVY DUTY]- Heavy duty steel frame provides stability and reliability when in use
• [LARGE BASE]- With a 10" x 10" base dimension you can rest easy there won't be any movement of the jack while in use under your vehicle
• [LIFTING RANGE] - Minimum Height: 13-3/10" (338mm) & Maximum Height: 19-7/10" (500mm)
• [HOLDING PINS] - Heavy duty holding pins for adjustable heights
• [WARRANTY] - Covered by a 2 years warranty that covers materials and workmanship

User questions & answers

Question:	What is the minimum height of stand without extension
Answer:	read ad 13" min i dont know why u would use with out extent. 10 1/2 inch just the base
Question:	How tall are these without the pin and at the first setting
Answer:	11.5” in the middle and 11.75” higher edges of the v shape
Question:	How many pin holes, and what is the distance between the pin holes
Answer:	4 pin holes about an 1 and 1/4 inch
Question:	Are these 22 ton each or 22 ton a pair
Answer:	Each jack stand is rated for 22 tons.

Product features

Dimensions

• 10" X 10" Base providing a large base to ensure stability and ease of use
• Heavy duty steel frame provides that piece of mind and reliability in any situation

Piece of Mind

• Work with a HIGH level of confidence knowing this heavy duty steel stand will hold.
• Robust but easy to move
• Makes other jack stands seem like toothpicks ready to break

Versatile

• Can be used for cars, trucks and even large heavier trailers
• Great for agriculture, industrial and construction environments
• Could support equipment in fleet garage

Adjustable Height Positions

• 13 3/10" to 19 7/10" Height Adjustments for any level of use
• Heavy Duty Holding Pins ensure safety when height adjusted upward

Product description

The Torin BIG RED T82001 hydraulic trolley service jack combo includes floor jack and jack stands, providing you with the essentials to lift and support most cars, trucks, and SUVs. The floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster. It has a 2 ton (4,000 lb) load capacity and features a minimum lifting height of 5-1/4" and a maximum height of 13-3/8". A safety bypass system prevents over-loading and ensures safe operation. Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability. A built-in carrying handle allows the floor jack to be lifted quickly for ultimate portability. The jack stands are used to support your vehicle after lifting with the jack and are constructed of high-grade forged steel with a welded frame design for durability. Adjustable height ranges from 10-13/16" to 16-9/16" with a 2 ton (4,000 lb) load capacity. Multi-position ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place. It features a large saddle surface area for better contact with the load being supported. A wide pyramid foot base provides added strength and stable support. Tested for reliability and safety to meet ASME standards. The hydraulic trolley service/floor jack combo includes a limited 1 year manufacturer warranty.

• Hydraulic trolley service/floor jack combo includes floor jack and jack stands, providing you with the essentials to lift and support most cars, trucks, and SUVs; Constructed with heavy duty steel, providing long term durability
• Floor jack has a 2 ton (4,000 lb) load capacity and features a minimum lifting height of 5-1/4" and a maximum height of 13-3/8"; Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability
• Equipped with a safety bypass system prevents over-loading and ensures safe operation; built-in carrying handle allows the floor jack to be lifted quickly for ultimate portability
• Jack stands feature an adjustable height that ranges from 10-13/16" to 16-9/16" with a 2 ton (4,000 lb) load capacity; Multi-position ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place
• Each jack stand has a large saddle surface area for better contact with the load being supported; A wide pyramid foot base provides added strength and stable support; Meets ASME safety standards and includes a limited 1 year manufacturer warranty

User questions & answers

Question:	How many jack stands does this come with, 1 or
Answer:	Mine came with 2
Question:	Does come with a case
Answer:	No
Question:	Is this safe to use on a ford explorer? Is it safe to use on a truck? What does this come with
Answer:	It works on our Silverado, so I would say yes. It comes with two jack stands.
Question:	Which "jack puck" would fit this floor jack
Answer:	I use a piece of wood as a buffer.

Product description

Pro-Lift F-2330BMC is Pro Lift 2 Ton floor jack and 2 Ton jack stand combo.

Both floor jack and jack stands are built with heavy duty steel to provide you the long lasting durability. The floor jack features the bypass device that protects from over pumping for safe operation.

With two front wheels and two rear swivel casters, it makes the maneuver smooth and easy. In addition, with the swivel saddle, it provides easy positioning and safety. There is also carrying handle on the jack to enhance the portability.

In the combo pack, there are pair of ratcheted 2 ton jack stands included to safely support your lifted vehicle. The jack stands feature the high quality cast ductile iron ratchet bar. At the same time, with the height adjustment mechanism, it allows smooth upward movement while releasing handle locks into position.

In the combo kit, you will also find a convenient blow molded storage case. It gives you the ability to easily store and carry.

- Built with the Heavy Duty Steel with Two Front Wheels and Two Rear Swivel Casters

- Bypass Device Protect from Over Pumping Damage

- High Adjustment Mechanism and High Quality Cast Ductile Iron Ratchet Bar

- Packed in a convenient blow molded storage case

Specifications

- Capacity: 2 Ton (Floor Jack & Jack Stand)

- Lift Range: 5-1/4 to 13 inch Floor Jack & 10-1/2 to 16-3/4 inch Jack Stands

- Package Dimension: 30.71 x 9.85 x 5.71 inch

- Item Weight: 36 Lbs

Pro Lift F-2330BMC 2 Ton Floor Jack & Jack Stand Combo is backed by 90 Days warranty from the date of the purchase.

• Heavy duty steel construction
• Convenient blow molded storage case
• Carrying handle on jack
• Swivel casters for easy positioning
• Pair of ratcheted 2 ton jack stands included to safely support your lifted vehicle

User questions & answers

Question:	Can lift ford ranger
Answer:	each jack is 2 ton
Question:	It's this jack strong enough for a 2000 Chevy Astro Van
Answer:	No
Question:	What is the diameter of the pad? I'd like to buy an adapter too and want to make sure it fits
Answer:	Only if you have the older HF Pittsburgh 3 ton jack stands, item 38846. The new Harbor Freight 3 ton jack stands, item 62392 will NOT fit. The saddle is much too thin, almost half the thickness of these pads. HF really cheapened them.
Question:	Is each jack stand rated at 2 ton
Answer:	Yes, they fit mine nicely.

Product features

Pro-LifT F-2330BMC Grey Floor Jack and Stand Combo

• A great combo kit including a 2 Ton jack and 2 Two Ton jack stands in a blow mold carry case. This kit is easy to transport, and simple to store. If your shop is mobile, this kit is definitely for you!
• Patented bypass device protects against overpumping for safe operation
• Heavy duty steel construction provides long term durability
• Swivel saddle and swivel rear casters provide easy positioning and safety
• High quality cast ductile iron ratchet bar
• Height adjustment mechanism allows smooth upward movement while release handle locks into position
• Ideal for auto, truck service, farm, and shop use

Product description

The Torin TCE AT82001U hydraulic trolley service jack combo includes floor jack and jack stands, providing you with the essentials to lift and support most cars, trucks, and SUVs. The floor jack is constructed with heavy duty steel, providing long term durability with an industrial luster. It has a 2 ton (4,000 lb) load capacity and features a minimum lifting height of 5-1/4" and a maximum height of 13-3/8". A safety bypass system prevents over-loading and ensures safe operation. Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability. A built-in carrying handle allows the floor jack to be lifted quickly for ultimate portability. The jack stands are used to support your vehicle after lifting with the jack and are constructed of high-grade forged steel with a welded frame design for durability. Adjustable height ranges from 10-13/16" to 16-9/16" with a 2 ton (4,000 lb) load capacity. Multi-position ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place. It features a large saddle surface area for better contact with the load being supported. A wide pyramid foot base provides added strength and stable support. Tested for reliability and safety to meet ASME standards. The hydraulic trolley service/floor jack combo includes a limited 2 year manufacturer warranty.

• Hydraulic trolley service/floor jack combo includes floor jack and jack stands, providing you with the essentials to lift and support most cars, trucks, and SUVs; Constructed with heavy duty steel, providing long term durability
• Floor jack has a 2 ton (4,000 lb) load capacity and features a minimum lifting height of 5-1/4" and a maximum height of 13-3/8"; Equipped with large steel casters and 360-degree swivel casters for smooth maneuverability
• Equipped with a safety bypass system prevents over-loading and ensures safe operation; built-in carrying handle allows the floor jack to be lifted quickly for ultimate portability
• Jack stands feature an adjustable height that ranges from 10-13/16" to 16-9/16" with a 2 ton (4,000 lb) load capacity; Multi-position ratchet bar has a sawtooth design, allowing for quick height adjustments that lock into place
• Each jack stand has a large saddle surface area for better contact with the load being supported; A wide pyramid foot base provides added strength and stable support; Meets ASME safety standards and includes a limited 2 year manufacturer warranty

• Dimensions: 9.75"L x 9.75"W x 12.25"H. Patented design combines jack stand and bottle jack in one unit
• Safety bar locks unit at desired height. This jack is for trucks and off road type vehicles
• Portable jack designed to safely Lift and hold both Regular and unibody cars and trucks
• Highly durable. Wide steel base for stability under load. Height range is 11 inch to 21 inch, but its default lift range is 11 to 17.25 inch, it can be raised to 21 inch if adjusted manually
• Strong safety bar keeps jack from lowering once it has been raised to maximum height

User questions & answers

Question:	I lost the jack arm, how can i get a replacement
Answer:	I purchased the jack to jack up my utility trailer. Tractor Supply used to carry this jack, they no longer carry it., so I went on line & Found that Powerbuilt is the manufacturer.... Google them, & send them a note, about needing the jack arm.
Question:	How do you release the safety latch? Help
Answer:	Raise the jack, lift the latch while lowering the jack.
Question:	What is the exact measurement of this jack? For storage purpose
Answer:	I measured it in half light so do not bet the farm on the answer but it should be close. The base is 9"X9" and it is nearly 13" tall. That will get you close.
Question:	I see a lot of bad reviews on quality, does anyone know if they are better built now? Has there been a quality control or design improvement
Answer:	You must be working for a company that does not make or represent the Powerbuilt name. By your question about quality, you are going off of rumors and gossip.I have been in the very dangerous employment of glazing, sandblasting, industrial coating, waterproofing, painting, industrial and commercial building repair, and skyscraper window washing. Safety and quality of tools for myself and my crew is my first concern. I actually was a consultant for Landa Pressure Washers,and many Industrial Chemical Companies like Shermiin Williams and Miller Paint. Many things can go wrong when you'r 80 feet up on a crane at the shipyards,or sandblasting, testing , and coating a Bridge in Portland Oregon, or just fixing your truck or car. Powerbuilt tools, and especially this #640912 keeps me verysafe, better than a car jack alone or a jack stand alone. Look up what the Fire Departments and first responders use at your local Safety Equipment Supplier.Look up the Fisk Descender, a safety device made by my previous employer and inventor, Brian Fisk. We used this safety device to descend from buildings andCranes, and Holding Tanks at the Refineries. I pressure washed 8 to 10 story buildings hanging to prep them for coating or waterproofing or caulking. When I needthe safest support product I know to crawl under and work on a heavy machine or vehicle or industrial motor at Frito Lay or a support beam at Robinson Dairy, you'llsee this Powerbuilt 640912 keeping me safe. Now that I am retired from the Industrial world, I will continue to stand by and consult and train people with manyother Powerbuilt products.

Product features

Powerbuilt 3 Ton All-in-One Jackstand/Bottle Jack

The Powerbuilt 3 Ton All-in-One UniJack is designed to safely lift and hold both regular and unibody cars and trucks.

All Unibody vehicles have factory-approved lifting points to prevent damage when jacking up the vehicle. But with a conventional jack, it’s challenging to properly lift and hold a unibody vehicle, because once the vehicle is raised with a jack, there’s no space left to add a jackstand.

The Powerbuilt 3 Ton All-in-One solves this problem with an ingenious design that both safely lifts and securely holds a Unibody vehicle using a single lift point. The Unijack offers both concave and flat lifting surfaces to accommodate a wide variety of lift points.

What’s more, it eliminates the cost and hassle of a floor jack, it’s easier to lift, move and store and costs a lot less too.

The 6000 pound All-in-One offers lift range from 11 to 21 inches, which makes it perfect for trucks, SUVs and vans.