11 best auto battery ratings

Product description

AIMS Power PICOGLF20W24V120VR Pure Sine Inverter Charger, 2000 Watts Continuous Power Output, 6000 Watts Surge Rating, 24V, Battery Priority Selector, Auto Frequency, Four Stage Smart Charger

This 2000 watt 24 volt low frequency AIMS Power inverter charger is three products in one

An inverter that transforms DC (direct current) power stored by batteries into AC (alternating current) electricity, A built-in 30 amp transfer switch and, A built-in 30 amp battery charger which uses AC power

Key Features

• 2000W low frequency inverter, 6000W surge for 20 seconds 300% surge capability
• Battery Priority Selector, Terminal Block, Marine Coated and Protected, Multi Stage Smart charger 30 Amp
• Auto frequency, 10msec typical transfer time, Selectable 25W power save mode (hibernation)
• 7 battery type settings for charger, Over Charge Protection Shutdown 31.4V
• Selectable Charge setting based on battery type, Four Stage Smart Charger

Specifications Inverter Output Specifications:

• Continuous Output Power: 2000 Watts
• Surge Rating: 6000 Watts (20 Seconds)
• Nominal Efficiency: >88% (Peak)
• Line Mode Efficiency: >95%
• Ambient operating temperature: 14°F to 122°F

Input Specifications

• Nominal Input Voltage: 24.0Vdc
• Low Battery Alarm: 21.0Vdc-22.0Vdc
• High Voltage Alarm: 32.0Vdc
• Power Saver Mode Idle Consumption: 12.2 watts

Charger Specifications

• Output voltage: Depends on battery Type
• Charger Rate: 30A
• Over Charge Protection Shutdown 31.4V

Transfer Switch Specifications

• 30 amp auotmatic transfer switch
• 10 ms (max)
• Dimensions (LxWxH): 16.48" x 8.74" x 7.1"
• Weight:50 lbs

• POWERFUL: 2000W continuous, 6000W surge for 20 seconds, 24VDC, 16 amps, 120VAC pure sine clean power, low frequency, auto transfer switch and 30A smart battery charger for 8 different battery technologies including lithium.
• PROTECTIONS: Overload, over temp, high voltage, low voltage, short circuit, internally fused, low and high voltage alarm, cooling fan, and isolated ground neutral.
• FEATURES: GFCI outlet, AC direct connect terminal block, charge current control dial, dip switches to set priorities, auto gen start, conformal coated, power save mode and battery temp sensor. Only one set of cables needed. Optional remote available.
• APPLICATIONS: Ideal for large applications going back and forth from shore/generator and inverter power automatically. Homes, boats, RVs, solar, mobile business & work trucks. 24 Volt more efficient and can use smaller cables. Offgrid & back-up power.
• TRUST AIMS: Buy with confidence. In business for over 20 years. All tech and warranty support in Nevada.

User questions & answers

Question:	With a "30a charger" i am assuming this refer's to 30a at 24dc and therefore 6a on the 120v ac input side
Answer:	That is correct.
Question:	Can I connect my solar panels directly to this and have it charge the batteries without any other controller or do I need some other controller
Answer:	You must have a charge controller for this to work. The solar panels connect to the charge controller, the charge controller connects to the batteries, the batteries connect to the AIMS inverter. The purpose of the charge controller is to regulate how much power the solar panels send to the batteries. Hope this helps.
Question:	does the charger support Lithium
Answer:	I purchased this for use in a 24V Battleborn Lithium system. I had fits trying to figure out why intermittently the Battery Management System (BMS) would should down. Battery supplier tells me it's the inverter, inverter tells me it's the batteries malfunctioning. I asked AIMs phone support what the inrush current requirement was for this inverter? Phone support responded with 21Volts is required for the unit to operate properly and would not answer my question. The BMS shuts down at 700A according to Battleborn. I complained to AIMs and a more knowledgeable and helpful engineer responded. I ended up having to use a switch and resistor to pre-charge the inverter prior to connecting the inverter. This is not supposed to happen until the inverters are 4KW and above. General feedback I was given regarding AIMS is it's a lower quality Chinese made product. So far it is working but it also overcharges my batteries in the charger mode slightly above 30V where it should be 28.8V but that is with an AC input of 125V.
Question:	Has anyone purchased this that can give some long term reviews? How is the power consumption? Are you still happy with it? Any issues
Answer:	Owned and used for 7 months on an off grid system, 320amp/hr @24v battery bank with 800 watt array and this unit works great!! Have a victron battery monitor and the consumption is right around 30 watts at idle for the inverter. It is always on and it will invert 12 led lights, a ceiling fan, bath fan, all for around 175 watts! It handles the high loads of a blender very well, even our 3/4 ton air conditioner with minimal light flickering. Also easy to set up a generator backup and connecting shore power right up to it. It transfers from power sources very quickly with no interruptions. No issues!

Product description

Allstar Gray 50 Amp Rating Battery Cable Quick Disconnect for 6 Gauge Size Wire - Pair features a battery cable that is able to quick disconnect. It fits a 6 gauge size wire and has a 50-amp rating. It is made from quality plastic material and is red in color. The battery disconnect provides a connection for battery charging or for quick battery changes during a race. It prevents accidental reverse polarity and the cable terminals are included. A 50 amp model connector is also available from Allstar by ordering part 76230. It is sold as one pair and backed by a 90-day limited factory warranty.

• Battery cable quick disconnects fits 6 gauge size wire and have a 50-amp rating
• Cable terminals are included
• This battery disconnect provides a connection for battery charging or for quick battery changes during a race
• Made from quality plastic material and gray in color

User questions & answers

Question:	What difference between sh and sb as the one i have is sh and this one is sb
Answer:	Approx. six inches or so. This is a fairly short jack.
Question:	Does this jack handle work on a 1994 Lance Squire 8000 cabover camper
Answer:	I would guess about 3 inches by 3 inches. Not very large.
Question:	Is this crank compatible with Atwoods Manual Jacks
Answer:	If this jack was place in the storage box on its side, I believe that it should fit. The base is about 3 inches by 3 inches. This is a small jack.
Question:	Does this include a pin for the jack that would all this handle to drive the crank shaft on the jack? It shows the notch to get around this pin
Answer:	I believe the range they are showing is the min. and max. without the top screw adjustment included.
Question:	Does this fit the same fitting as the tst-129 drill adapter. pictures doesn’t show the end
Answer:	about 2.5 inches it is a hefty jack
Question:	Does this work on hydraulic Rieco jacks
Answer:	China
Question:	Does this have a backup remote
Answer:	Yes they do,nice jack.
Question:	What is the difference in this model and model
Answer:	about 30 pounds, not lite
Question:	Are the remote and controller box included or just the power heads
Answer:	I don't think there would be very much maintenance required. Perhaps just keep them clean and occasionally lube the ratcheting mechanism. If you want more details, you might contact the manufacturer.
Question:	How high do they lift
Answer:	Mine do, I bought these to let my trailer tongue rest on them because I store a side by side in my trailer and it is very heavy I found that this is a great product.
Question:	Does this set come with brackets and bolts to attach them to the camper
Answer:	There is no certification information listed on the stand it's self. They are built very well, but I don't put 6 tons on the jacks. My use is on 2500 lb vehicles. Hope this helps.
Question:	Do you attach this to camper and if so, does it come with the hardware
Answer:	The brown parts that you see are made of a nice thick leather and the rest is a thick black synthetic material. Yes it is black.
Question:	will these clear a dually
Answer:	Negative.. I think the fatlip model are the ones that come with it. You can buy it separate though, it’s called the oxy shield...

Product description

Prevents primary battery discharge. Water resistant black phenolic plastic;

This Car relay with Red copper binding post: ensuring heavy current can be transited safely; Rated voltage 12VDC, maximum instantaneous through current 500A. Work long times maximum 200A;High quality: ensuring the maximum electric current can be transferred, for Multi-battery system Forklift Engineering Automotive



Specifications:

Protective features: sealing type           Coil power: 12V DC      Weight: 235g

Contact  material: AgSn0_27In_20_33   Contact form: 1H(1A)    Contact Ratings: 500A

Contact Resistance: 100mMax at 6VDC 1 A

Life Expectancy Electrical：100,000 Operations(at 30 Operations/minute)

Life Expectancy Mechanic： 10,000,000 Operations

COIL SPECIFICATION

Coil Resistance：(16W)  9Ω        Max Operate Voltage(VDC): 8              

Mix Release Voltage (VDC): 1.2   Max Applicable Voltage (VDC): 14

Temperature Range： -30~80℃             Vibration Resistance：10-55Hz, 1.5mm

Shock Resistance：                        

Operations Extremes： 50g     Damage Limits： 100g                         

Humidity：40-85%                 Insulation Resistance： 100mΩ min at 500vdc

Safety Standard：

Dielectric Strength Between Open Contacts： 2000VAC(for 1 minuter/s)

Between Contacts and coil： 1500VAC(for 1 minuter/s)

Operate Time： 50ms         Release Time： 50ms



Package Included:

1 x Heavy current relay

• It help extend battery life
• Universal 12V applications
• Prevents primary battery discharge
• Made of water resistant black phenolic plastic
• The main function of this product is to switch on, it can be used alone, it can be also connected to control to use

User questions & answers

Question:	What is the duty cycle for this solenoid? Is it rated for continuous duty
Answer:	Hi - it is a full 16" from the center of the pad to where it begins to transition up thicker

• ☑【UNIVERSAL】Heavy-duty & multipurpose universal battery quick connector set from Driver Recovery Products. Provides simple and convenient method for connect/disconnect power to a winch or other electrical device such as remote battery chargers, power inverters, solar setups,trailers, or for any purpose requiring a high-current, quick-disconnect connector.
• ☑【DURABLE】Combined shell made from sturdy PC fire-retardant materials, allowing for over 10,000 connect/disconnect actions. With fitted rubber boot covers, protect against dust, moisture and corrosi
• ☑【SAFE】Both ends are suitable for connection to the power or load side because of its identical connectors.The ends are made to connect only one way, making it impossible to connect the wrong polarities to one another,preventing accidental reverse polarity when hooking up a charger.
• ☑【EFFICIENT】The heavy duty components are suitable for low or medium current use. With 4 terminal pins made of red copper coated with silver have strong electrical conductivity and reduce the resistance to guarantee stable voltage and current.
• ☑【INSTALLATION】It is very easy to use and install. Insert the wires into the terminal pins, then solder or crimp them. Insert the terminal pins into the connector housing and lock them in place

User questions & answers

Question:	Are these suitable for marine applications
Answer:	Hi, Craig! Thank you for your interest in our product! Unfortunately, we don't make custom orders at the moment, but we will consider your suggestion when we will design new products.
Question:	These do not fit energizer jumper cables, 30 feet, 1 gauge cable. i need ones that do
Answer:	Rapid pump feature works until it contacts the weight, then it moves up about half speed as it lifts the car. Nice feature.
Question:	title says 1/0 awg and description says 2/4 awg
Answer:	No , it does not come with a saddle pad.
Question:	Will Bunker Indust state whether these can connect safely to an anderson plug
Answer:	Looks like a separate seal kit isn't offered. From the user manual, the part number for the hydraulic unit is RS6602LP27 and I've only seen it for sale online in one location for $164.

Product features

HOW TO INSTALL

• Insert the wires into the terminal pins, then solder or crimp them
• Insert the terminal pins into the connector housing and lock them in place
• Operating Temperature Range:-4°F-221°F / -20°C-105°C
• Connector Dimension:As the picture show
• Vibration Resistance: Excellent
• Impact Resistance: High
• Suitable For: UPS battery power connector
• Connect/disconnect Cycles: 10,000 times

SPECIFICATIONS

• Material: PC fire-retardant materials+stainless steel
• AMP Rating: AC/DC 50
• Gauge: 6-10 A.W.G
• Wire Diameter: 6-16 AWG at most
• Rated Voltage: UL rated at 600 volts DC or AC
• Medium Withstanding Voltage: 2200DC
• Contacts material: copper silver
• Fire rating: 94-V0
• Connector Dimension: 1 7/8"" long x 1 3/8"" wide x 1/2"" thick
• Terminal Pins Diameter: 0.22" /Wire Size: 0.05" - 0.52"

Product description

The Carmanah CMH-AGM-100 is designed for heavy power requirements such as Solar and Inverter installations. It is easy to install and easy to carry with the built-in carry handles. It is designed for Marine, RV, Off Grid applications. The CMH-AGM-100 has gone through strenuous testing and is very reliable. It has been proven to be reliable and maintenance free for Carmanah' s Outdoor Lighting applications world-wide. This battery is an absorbed glass matt battery which is sealed. The battery recaptures its own gasses so it does not need to have distilled water added to it like a wet cell battery. The CMH-100-AGM is tested to 110 amp hours at the 100 hour rate and 105 amp hours at the 20 hour rate. The CMH-AGM-100 has outperformed brand named Group 31 batteries when tested at our facility over a number of different temperature ranges.

• Great for Marine, RV, Fleet, Off Grid applications
• 110 Amp Hour At 100 Hour Rate
• Maintenance Free and Spill Proof
• Easy installation and carrying with built in handles
• Designed for heavy power demands seen in Solar and Inverter applications

User questions & answers

Question:	Does this really weight 67.6 pounds? The dimensions are listed as only being 13.2 x 10.8 x 8 inches
Answer:	3
Question:	What is the group size for this battery
Answer:	I don't think so. I have one regular passport and one with extra pages and it is tight.
Question:	anybody know what the warranty is on these batteries? it is not listed anywhere I can see
Answer:	4" X 6" when closed
Question:	Just ordered it and noticed it does not mention the voltage! What is the voltage
Answer:	No specific place for coins but you can put coins in the inner pocket. They will probably fall out though. I personally wouldn’t use for coins.

• 🔧【Wide Test Range】The latest iBT100 12 Volt Automotive Battery Analyzer from Vident is dedicatedly developed to test 6V & 12V regular flooded, AGM flat plate, AGM spiral and gel batteries. And covers most of the battery rating standards: CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE standards, for accurate battery health status checking.
• 🔧【Car Battery Doctor】Using advanced conductance testing technology, high quality metal alligator clips with rubberized sleeve protector to ensure stable and safe communication all throughout test.Quick and accurate test result display in just 3 seconds.(Please note: Connecting the black clamp to the negative(-) terminal first and then the red clamp to the positive(+) terminal.)
• 🔧【Friendly Design】Test the battery directly in the cat without removing the battery to get bad cells.Does not emit light, heat or spark, or discharge battery - keeps operation safe for all levels of users , automatic temperature compensation.
• 🔧【Worth to Own】Extremely easy to use with large backlight LCD display and menu-driven operation For 3 seconds to get battery status, check battery health and detect faults. Multiple language are available:English, French, German, Italian, Polish, Portuguese, Russian, Spanish, Dutch,Turkish.
• 🔧【Service】We aim at trying our best to offer you customers the best products and services. Reply within 24 hours, refund allowed and other policies available to make you unworried before/after the purchase.

User questions & answers

Question:	What settings do i use for wheelchair batteries, u1, group 22, 34, 24 agm and gel
Answer:	No, it is not a battery load tester
Question:	Does this works to test 12v 7ah batteries? like the batteries used in ups backup systems
Answer:	Not very long,but enough to tester.
Question:	Can I use this to check for a Bad ground on my car
Answer:	No this is not amp metrr
Question:	Is this also a battery load tester
Answer:	There is no manual. There is video on youtube that shows how to use it. Good luck to you.

Product features

iBT100 12V Battery Analyzer Key Features:

1. Multiple Vehicle Applications:Passenger cars and light duty trucks

2. Strong Capacity:Works on 12V batteries, battery rated from 100 to 1100CCA

3. Tests Multiple Battery Types:Regular flooded, AGM flat plate, AGM spiral and GEL

4. Tests Multiple Rating Systems:CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE

5. Tests the batteries on the car directly:No need to remove the battery. Detects bad cells

6. Quick and accurate test result display in just 3 seconds

7. Does not emit light, heat or spark, or discharge battery. Keeps operation safe for all levels of users,automatic temperature compensation

8.Extremely easy to use with large backlight LCD display and menu-driven operation

9.Mulit-Language:English, French, German, Italian, Polish, Portuguese, Russian, Spanish, Dutch,Turkish

Wider Batteries Testing Range

• Battery Type Supported:Regular Flooded, AGM Flat Plate or AGM Spiral, and Gel battery etc.
• Battery System Standard Supported:CCA, BCI, CA, MCA, JIS, DIN, IEC, EN, SAE.

In / Out of Vehicle

• Two test modes, support both in and out of vehicle test. That allows you to test a battery according to its location, so you'll get a more accurate test result quickly, and replace the bad cell in time.
• The most importance is that you can test it on the car without removing the battery.

Fast & Accurate Results

• Quick and accurate test result display in just 3 seconds.It will display CCA value, CCA rated, health state(%), charge state(%) adn voltage(V) to let me know you battery condition.
• Keeping operation safe:Does not emit light, heat or spark, or discharge battery.

Additional Value

• Mulit-Language:English, French, German, Italian, Polish, Portuguese, Russian, Spanish, Dutch,Turkish. 10 languages are available for you to choose from.

How to Change Language for iBT100 Automotive Battery Tester?

1. After connect to your vehicle, please press but power button

2. Then press the above arrow button enter the Language menu

3. Select the language you need and Press OK button. Then your iBT100 battery tester language will be setted.

• ★【8 Gauge Silicone Wire】Premium 8 AWG Wire 25ft Red & 25ft Black ( Separated wire but package both in one spool ) All gauge silicone wire available in Shonsin amazon store from 6 gauge to 26 gauge.
• ★【100% OFC Copper Conductor】8 AWG Wire Oxygen Free Copper conductor features wonderful conductivity, Current Rating: 65 Amp, Voltage Rating: 600Vac
• ★【Ultra Flexible】 The combination of 1650 strands 0.08mm copper conductor (8.29mm2) & silicone insulator yields the most flexible wire construction. Extreme Soft 8 Gauge Silicone Wire is ideal with applications where routing a wire through a tight space is required such as, box builds, equipment, or handheld devices and has excellent weather-ability.
• ★【Silicone Insulator】 Resists high & low temperature, water, oil, chemicals and abrasion. Compared to Thermoplastic material (like PVC), silicone insulation will not melt when exposed to high temperatures. If the insulation melts, this may cause a short circuit which is very dangerous.
• ★【Resistant High & Low Temperature】8 AWG Wire standard temperature range is -60°C to 200°C. In most applications, it may be heated from 180 to 200°C continuously and is also very flexible at extremely low temperatures (stiffening temperature of approximately -115°C).

User questions & answers

Question:	Is the 50' spool one 50' piece or two 25' pieces
Answer:	No. It's a great scanner on the road but for home it is less than ideal. You can only scan one page at a time and it's sometimes hard to get the page to go through without distortion.
Question:	Can this wire be used for speaker wirer for a 10 inch subwoofer
Answer:	I have not personally tried using this with Windows 8, but here is a link to their web site which indicates it will work.http://www.irislink.com/c2-1638-189/Microsoft-Windows-compatibility.aspx
Question:	This wire diameter is 8 mm as listed on the package. this corresponds to 0 awg, not 6 awg. i'm looking for actual 6 awg gauge wire
Answer:	Yes
Question:	Is this the correct wire to wire a ceiling fan? TIA
Answer:	Only one ring. 2-3 keys.

Product features

Why SHONSIN Silicone Wire？

• 6 gauge to 26 gauge silicone wire available in SHONSIN store.
• 100% Copper Conductor: Oxygen Free Copper conductor features wonderful conductivity.
• Silicone Insulator: As a Thermoset material, silicone will not melt when exposed to high temperatures.
• Ultra Flexible: The combination of many strands 0.08mm OFC copper conductor & silicone insulator yields the most flexible wire construction.
• Resistant High & Low Temperature: -76℉ to 392℉ ( -60℃ to 200℃ )
• Voltage Rating: 600V
• RoHS Compliant

Why Silicone Insulator ?

• SHONSIN Silicone Wire standard temperature range is -76℉ to 392℉ ( -60℃ to 200℃ ). In most applications, it may be heated from 180 to 200°C for a year and is also very flexible at extremely low temperatures (stiffening temperature of approximately -115°C).
• Compared to Thermoplastic material (like PVC), silicone insulation will not melt when exposed to high temperatures. If the insulation melts, this may cause a short circuit which is very dangerous. Shonsin high temperature silicone cable is resistant to high temperatures and will not melt.

Product description

Heavy Duty Battery Master Switch - Single circuit, waterproof switch is UL approved. Removable key. Base diameter is 2.25 inch.

• Main Switch, battery
• Rated 100A @ 24V
• Base diameter is 2.25”
• Conveniently packaged
• One Year Limited Warranty

User questions & answers

Question:	will this work with a 12VDC 11AH generator battery
Answer:	It does not say....It only tells you the dpi resolution being 300/600/1200.
Question:	Where is this switch made
Answer:	The one I bought would work with chrome if you plugged the USB into the scanner, scanned and then walked over to the computer with Chrome plugged the memory stick in and uploaded it. So I guess it depends on what your definition of wireless is.
Question:	where i can get a bracket to mount this switch
Answer:	The unit does not attach to your computer unless you use the cord....So, yes.
Question:	Do you connect this to the positive or negative side of the battery
Answer:	No but we do sell ID scanners from CSSN

Product features

HELLA Electronics

With our comprehensive and innovative product range, HELLA is one of the leading suppliers of electronics. Countless automobile producers around the world place their trust in HELLA's quality products. With this, we are dedicated to providing our same long-standing, high quality original equipment to the independent aftermarket. Independent shops benefit from HELLA's original equipment expertise and the security of knowing that those same parts are available for their aftermarket needs.

Energy Management

HELLA’s energy management products help to provide the best possible coordination of available and required capacity. Our products range from high voltage sensors to intelligent battery sensors and high-performance DC-DC converters, as well as battery management systems.

Environmental and Position Sensors

Our sensor portfolio includes pedal sensors, position sensors, sensors for motor oil and temperature management, and rain/light sensors.

Radar Sensors

HELLA has been manufacturing radar sensors in the 24 GHz narrow-band range for over a decade. The sensor system is compatible with the standard functions of blind spot detection, lane change assistant and rear parking assistance.

Intelligent Battery Sensor

The IBS reliably and accurately measures the battery parameters: voltage, current and temperature. Information about the battery’s state of charge (SOC), state of battery health (SOH) and state of function (SOF) is calculated algorithmically from the measurements. The IBS is designed for use in starter, gel and AGM batteries to monitor in-vehicle starter or consumer batteries. The IBS can be directly integrated into the vehicle's electrical system with the standardized LIN protocol.

HELLA 24 GHZ Radar Sensors

Our radar sensor safety features include: Blind Spot Monitoring: monitors the driver's blind spot and warns the driver of dangerous situations. Rear pre-crash system: tracks vehicles approaching from behind. Lane change assistant: warns the driver if a lane change might be unsafe. Rear cross traffic alert: warns the driver of approaching vehicles when maneuvering out of a parking space. Vehicle exit assistant: monitors the area to the right and left of the vehicle doors.

Accelerator Pedals

The HELLA accelerator pedals designed for floor-mounted or suspended installation can be used in a wide variety of vehicles - ranging from sports cars and electric vehicles, right up to robust applications in agricultural vehicles and construction machinery. Thanks to the wear-free measurement principle of the CIPOS sensor developed in-house at HELLA (see description of design and function of the angular position sensors) and its extremely low level of mechanical wear, this version is particularly preferable to contact-type pedals in the case of frequent small movements.

Rain/Light Sensors

The full range of functions of the rain/light sensor (five functions: rain sensor, light sensor, solar sensor, humidity measurement, and head-up display) can only be used for passenger vehicle applications. This sensor can only be used to a limited extent in vehicles with special windshields (thick, slanted, transmission). The optics of the second sensor are specially designed for vehicles with steep windshields and combines the rain and light recognition functions (environment and tunnel recognition).

Oil Level Sensors

Our oil sensors ensure that the engine cannot work unnoticed with too little oil. The tried-and-trusted technology of these ultrasonic sensors work on the delay time principle and records the filling level continuously during the trip.

Throttle Body

This controls the amount of intake air of the engine. Intake air volume changes depending on the opening angle of the throttle valve. This angle is controlled by the engine control unit and fulfills the tasks of the idle adjuster in modern vehicles.

Voltage Stabilizer

Our voltage stabilizer provides an auxiliary power supply system in case of battery failure. Ensures automatic gearbox goes into P after for example an accident to set gearbox into “P” as standing position (emergency parking mode). It also sets automatic park mode for when the vehicle door is open.

Vacuum Pumps

Our vacuum pumps provide engine-independent vacuum support and a flexible installation location. It is a Dry-running system (no connection to the lubricating oil circuit required and maintenance-free). It also supports further use of conventional brake systems for alternative drive systems, such as hybrid and electric drives, and provides a reduction of energy consumption due to demand-based use, supporting pollution emissions.

Product description

Take the guesswork out of watering with a Rachio Smart Sprinkler Controller. The easy-to-use mobile app lets you manage your sprinklers without running back and forth to the controller, while automatic weather adjustments mean no more watering in the rain. Get peace of mind - Rachio knows just how much water your yard needs. Control your sprinklers using a smartphone or with category-leading smart home integrations, including Amazon Alexa and more. Master Valve-Compatible with master valve, pump relay, or indexing valve. Wi-Fi Connection - Wi-Fi (2.4GHz) required. Supports dedicated 2.4GHz and dual-band networks. Cannot operate on 5 GHz only networks. Sensors Rain Sensor - Wired & Wireless Normally Closed (NC) sensors, Soil Sensor - Wired & Wireless Normally Closed (NC) sensors, Wired Flow Sensors

• 5-STAR RATINGS. Amazon’s most- and highest-rated Wi-Fi sprinkler controller.
• Avoid watering in the rain. Exclusive weather intelligence automatically skips unnecessary watering with features like rain skip, wind skip, freeze skip, and more.
• Control from anywhere with the easy-to-use app. Run sprinklers, view upcoming schedules, and observe your estimated outdoor water usage.
• Experience fast DIY installation. Rachio Smart sprinkler controllers replace 99% of existing sprinkler controllers. Install in 30 minutes or less with no special tools needed. Our in-app installation tutorial helps you get online and watering in no time!
• Deliver all the water your plants need; no more, No less. Rachio creates tailored Smart schedules based on the specific needs of your lawn, including plant type, soil type, sun exposure, and more.
• Power source type: Corded Electric. No Hub Required for Voice Control

User questions & answers

Question:	Can you manually turn on zones from the unit itself without the use of a phone
Answer:	If you remove the front cover, there are buttons for selecting a zone and running it manually. There are LEDs in a circle around the Rachio logo, numbered to match the sprinkler zones as you select your target zone. Once the zone you wish to water is highlighted, simply press the manual run button. Good in an emergency, but this unit's primary use case is using the app or website.
Question:	Does this work if wifi is down? What watering schedule does it revert to in this case? Will the app alert me
Answer:	The Iro utilizes EEPROM, persistent memory, so the last saved schedule(s) are stored on the device itself. So Please rest assured knowing that if the Iro loses connectivity with your WiFi, it will always continue to water using the last saved. Any updates/changes to these watering schedules will upload to the Iro the next time it reconnects with the cloud. You will receive an e-mail notifying you that it is off line.
Question:	Can you manually start/stop zones via the app? When working on the system I would love to not walk back to the garage for this
Answer:	Yes. You can manually start/stop each zone individually from the app, as well as adjust how many minutes each zone is on.
Question:	What's are the differences between gen 1 and gen
Answer:	The sync up is totally different in that just approaching the devise with you smart devise it will ask for the serial number and then you are linked with the unit. There are several manual cycles when you do not have wifi available during initial installation. There is the function of the using flow sensors in the future. There is much more space for the valve wires. There is the visual of what valve is operating during the irrigation cycle on the controller to name a few.

Product features

Remote Control

Start, Stop, Pause or Skip individual zones - even create a Custom Run schedule - all from our exclusive Remote. Only Rachio offers smartphone control this precise.

Intuitive Schedules

Build schedules with confidence. Guided setup walks you through every detail, customizing the timing and frequency of watering to your specific landscape.

Exclusive Weather Intelligence

With advanced Rain, Freeze and Wind Skips, Weather Intelligence automatically adjusts watering schedules for predicted weather based on the latest local forecasts.

Customized Zones

Set up customized zones with confidence. Let Rachio recommend soil type based on your zip code, then add a few simple details like plant type, sun exposure and more to optimize watering for your specific yard.

Most 5-Star Ratings

Amazon’s most- and highest-rated WiFi sprinkler controller is the Rachio Generation 2 Smart Sprinkler Controller.

Committed to Sustainability

We make it easy to nurture a healthy, beautiful yard while embracing sustainable water use.

Easy Installation

Install it yourself - no special tools or expertise required!

EPA WaterSense Certified

Certification date: Dec 2014.

• 【BATTERY ANALYZER】 BT705 battery tester designed for 12 V or 24 V batteries with a capacity of 100 to 2000 CCA, such as regular flooded, AGM flat plate, AGM spiral, GEL and deep cycle batteries, 12V & 24V starting and charging system. The test results based on CCA, EN, CA, MCA, DIN, SAE, JIS and IEC Standards.
• 【CAR BATTERIES DOCTOR】 Adopt the advanced conductance testing technology, the premium quality copper clip and wire maintain a stable communication all throughout the testing process to provide you with reliable results! Accurately and quickly measure the actual cold cranking amps, capability of the vehicle starting battery and healthy state of the battery itself.
• 【CRANKING AND CHARGING SYSTEM TEST】 BT705 tester displays the decision on the starter system, cranking voltage, and cranking time in milliseconds. Also, the battery diagnostic tool can check 12V or 24V charging system to make sure the output voltage of the generator is in a regular condition, the rectifier diode works fine and the charging current is a normal status.
• 【WORTH TO OWN】 Winter is coming and you need to know how much life your batteries have left. BT705 can accurate reading of battery health status in just 2.5 seconds in its large and easy to use backlit LCD display, help you diagnose and resolve car health problems timely without disconnecting the battery or using a separate battery.
• 【100% SATISFACTORY SERVICE】 We promise 100% money back guarantee on this car battery tester. 7.8ft cable allowed you to do the test from inside of the vehicle, whether you own your personal mechanic shop or private owner, you’ll fall in love with this battery analyzer!

Product features

FOXWELL BT-705 12V Battery Load Tester

• Multiple vehicle applications ¨C passenger cars and heavy duty trucks.
• Tests batteries from rated from 100 to 2000CCA. Cold Cranking Amps settings is in increments of 1 and you can line up with your battery ratings from 100 to 2000CCA.
• Tests multiple battery types- regular flooded, AGM flat plate ,AGM spiral and gel.
• Tests multiple rating systems-CCA,BCI,CA,MCA,JIS,DIN,IEC,EN,SAE,GB.
• Tests the batteries on the car directly- no need to remove the battery.
• Quick and accurate test result display in just 3 seconds, detects bad cells directly.
• Tests 12&24 volt charging system.
• Quick starter analysis without disabling the ignition.
• Does not emit light, heat or spark ,or discharge battery-keeps operation safe for all levels of users.
• Automatic temperature compensation.
• Ripple voltage test for easy and intuitive check of faults.
• Extremely easy to use with large backlight LCD display and menu-driven operation.
• Rubberized sleeve protects, 7.8ft tester cable with metal alligator clips. Viewing/Printing Test Results, allow you view test results and print the data via optional Bluetooth printer.

MULTIPLE BATTERY TYPES TEST

FOXWELL BT705 Battery Analyzer is dedicatedly developed to test 12V regular flooded, AGM flat plate, AGM spiral and gel batteries and 12V & 24V starting and charging system. It provides a quick, easy and affordable solution for technicians to check battery health and detect faults of starting and charging system.

VEHICLE BATTERY ANALYSIS

1. GOOD BATTERY:Battery is in good condition.
2. GOOD-RECHARGE:Battery is in good condition but low current.
3. CHARGE & RETEST:Fully charge the battery and retest. If you still get CHARGE & RETEST after fully charge the battery, replace it.
4. REPLACE BATTERY:The battery is almost dead or the connection between the battery and battery cable is poor. Replace the battery and retest; or disconnect the battery cables and retest the battery using the out-of-vehicle test.
5. BAD CELL-REPLACE:The battery may be damaged.

VEHICLE CRANKING ANALYSIS

1. CRANKING NORMAL: The starter voltage is normal and the battery is fully charged.
2. LOW VOLTAGE: The starter voltage is low and the battery is fully charged.
3. CHARGE BATTERY: The starter voltage is low and the battery is discharged. Fully charge the battery and repeat the starter system test.
4. REPLACE BATTERY: Battery must be replaced before the starting system can be tested.
5. NO START: No vehicle start detected.
6. CRANKING SKIPPED: A start was not detected.

VEHICLE ALTERNATOR CHARGING SYSTEM ANALYSIS

1. NO PROBLEMS: System is showing normal output from the alternator.
2. NO OUTPUT: No alternator output detected. Check connections to and from the alternator, especially the connection to the battery.L
3. OW OUTPUT: Alternator not providing sufficient to power the system's electrical loads and charge the battery. H
4. IGH OUTPUT: Alternator voltage output exceeds the normal limits.E
5. EXCESSIVE RIPPLE: Excessive AC ripple detected. One or more diodes in the alternator are not working or there is stator damage.

Advanced Clamps and 7.8ft Test Cable

The all-metal spray gold clamps provides short circuit protection and spark proof protection, which ensure the safety of you and the battery tester. In addition to the protection clamps, the battery analyzer equipped with a 7.8ft long test cable. which allows you to do the "Start" and "Load Tests" from inside of the vehicles.

Light and Strong Packaging Case

The tester was packing in strong box which made of high impact strength material. With this protection carrying case, you can prevent your scanner from being damaged whether you place it in a trunk, toolbox, or garage. It fits right in the palm of your hand, making it an excellent addition to your tool box.

Product description

Special thin separators - allow two extra plates per cell to be installed, for 30% improvement in cranking performance. Engineered to protect against corrosion, withstand vibration, and deliver high cranking power.

• 12 Volt, 30 amp-hour extra plate battery. Heavy duty glass mat resists vibration damage
• Special thin plate separators allow 2 extra plates per cell to be installed
• 30 percent improvement in cranking performance
• Sulfate stop to reduce battery sulfation
• Dry battery - battery acid not included

User questions & answers

Question:	This battery comes ready to install
Answer:	Hi Kristina It is a sheet fed scanner that scans one page at a time. We have other models that use a document feeder, notably the IRIScan Pro 5.
Question:	This battery fit to 2009 seadoo rtx supercharger
Answer:	Dear customer, The IRIScan Anywhere 5 is currently being reviewed for an important update. That's why we had to remove it from the Google Play Store. In the meantime, you can connect your scanner to the wifi and go to "http://www.iriscan.anywhere" to access the internal storage of the scanner. For more information, visit this article: https://support.irislink.com/en-us/article/703-how-to-connect-to-the-scanner-via-wifi IRIS Team