13 best ho gauge train sets

Product description

Overland Limited Ready To Run Electric Train Set - HO Scale. The biggest and the best for serious railroad enthusiasts. From a powerful 4-8-4 steam locomotive, to an impressive consist of nine cars, this set has it all! The Overland Limited comes complete with Bachmann‘s exclusive E-Z Track snap-fit track and roadbed system. This Ready To Run Electric Train Set Includes: Union Pacific 4-8-4 steam locomotive and tender with operating smoke and headlight, grain car, three-dome tank car, flat car with logs, center-flow hopper, open quad offset hopper, two plug-door box cars, wood stock car, wide-vision caboose, body-mounted E-Z Mate couplers, 63" x 54" oval of snap-fit E-Z Track with 16 pieces of 22" radius curved track, 5 pieces of straight track, and 1 plug-in terminal rerailer, power pack and speed controller, illustrated instruction manual.

From the Manufacturer

The biggest and the best for serious railroad enthusiasts. From a powerful 4-8-4 steam locomotive, to an impressive consist of nine cars, this set has it all! The Overland Limited comes complete with Bachmann’s exclusive E-Z Track snap-fit track and roadbed system.

• Complete Ready To Run Freight Train Set
• Powered by a Union Pacific 4-8-4 Steam Era Locomotive and Tender with Operating Smoke and Headlight
• Includes; Grain Car, Three-Dome Tank Car, Flat Car with Logs, Center-Flow Hopper Car, Open Quad Hopper Car, Two Plug Door Box Cars, Wood Stock Car, and Wide-Vision Caboose
• 63" x 45" Oval of Snap-Fit E-Z Track, Power Pack and Speed Controller
• HO Scale 1:87
• Union Pacific 4-8-4 steam locomotive and tender with operating smoke and headlight
• 8 Freight cars and wide-vision caboose

User questions & answers

Question:	Hi i have a question, i have one of these 806 models that smokes just like this one, how much smoke oil do i put in?" i dont want to overfill it
Answer:	The scale doesn't seem to be listed, and I haven't seen the item in person but sent it to my 9-year-old nephew. I received a picture of him holding it, and I was pleasantly surprised at how large it is. I thought it might be very small, but it was a good size. Hope this helps!
Question:	Is this loco the smaller version of the big boy? can this pull half the cars the big boy can pull
Answer:	No. There is no base. Just the airplane is all that is in the box.
Question:	does it come with smoke
Answer:	If the 7 year old is used to building Legos it would take as long as the same size small Lego set.
Question:	Is this remote controlled? What would I need to mount it around a wall? Thanks
Answer:	Took my 11yo granddaughter less than an hour to build

Product features

Discover Everything Bachmann Trains Offers to Get Started in Model Railroading

Since 1833, Bachmann has been known for providing innovative design at a good value. We are now one of the world's largest distributor, by volume, of ready-to-run train sets, locomotives, track, and accessories. Bachmann is also the only train company to offer products in all five of the most popular scales: N, HO, On30, O, and Large Scale.

As a distributor of beloved Thomas & Friends products, Bachmann brings the adventures of Thomas the Tank Engine to life with a growing line of complete train sets, separate sale items, and accessories for children from 8 to 80-just add your imagination. Thomas & Friends is available in both HO and Large Scale.

Bachmann's exclusive snap-together E-Z Track System makes track setup quick, easy, and fun. Plasticville U.S.A. and SceneScapes buildings and accessories let you add the finishing touches for the perfect layout.

If You Are Purchasing a Train Set, It Will Include

1. Locomotive
2. Cars (Rolling Stock)
3. E-Z Track – available in either black roadbed with steel alloy rail or gray roadbed with nickel silver rail
4. Terminal/Rerailer
5. Terminal Wire
6. Speed Controller
7. Power Supply
8. List of Components

Track Assembly

1. Decide where to set up your train – a dry, firm, flat surface works best!
2. To make sure you have enough working room, make a test track layout by loosely placing track in desired configuration.
3. The terminal/rerailer section will later be connected to a power pack and power supply, so place it near an outlet or power strip.
4. Install under-track magnet, if your set comes with one. If your set does not come with one, magnets are available separately (HO Item No. 78999; N Scale Item No. 78998).
5. Assemble the track by pushing together. Make sure the rail and joiners are seated properly. Be careful that the rail joiners do not slip under the rail without properly connecting. This can cause train derailments and electrical circuit interruptions.
6. After track is assembled, double-check for joint connection and fit by lightly running your fingers over the top of the rails in both directions.
7. If you detect bumps or distortion on the track surface, recheck the rail joiner fit.

Power Connections

1. Power supply and speed control are plug and play; no tools are needed.
2. Power is supplied to the track and the locomotive by the power supply, speed controller, terminal wire, and E-Z Track terminal/rerailer.
3. First – turn knob on the speed controller counterclockwise until it stops (all the way to the left).
4. Next – attach terminal wire to the speed controller by plugging it in where it says 'To Track.'
5. Then – plug terminal wire into the E-Z Track terminal rerailer. Firmly push connector onto the track terminals.
6. Finally – plug the connecting wire from the power supply into jack on the speed controller labeled 'In.' Then plug power supply into a live wall outlet.
7. Some sets may come with a speed controller with two push button connectors. These are used to supply AC power to accessories.
8. To make positive and secure connections to these, push in buttons and insert each of the bare ends of the connection wire from your accessory.
9. The speed controller is capable of powering one accessory at a time.

Putting the Train on the Track

1. Put the locomotive on the track and run the wheels back and forth over the terminal rerailer track.
2. When the wheels glide smoothly over the track, you know the wheels are all on the track. If your set comes with a tender, attach it to the locomotive.
3. Add the rest of the cars that come with your set by placing them on the track and running them back and forth over the terminal rerailer until they glide smoothly. Then gently push the cars together – they will engage automatically.
4. Do not try to connect cars when positioned over an under-track magnet.

How to Use E-Z Mate Couplers (HO and On30 Scale)

1. Your set may be equipped with E-Z Mate magnetically operated knuckle couplers that let you perform real railroad switching and yard operations.
2. Coupling two cars with E-Z Mate couplers is as easy as pushing them together when they are not over an under-track magnet.
3. Uncoupling occurs only when over an under-track magnet and when there is no tension between the cars.
4. To uncouple E-Z Mate couplers, stop two couplers directly over the under-track magnet. With no tension between the cars, the couplers will open automatically.
5. If cars will not couple, check to be sure cars are not positioned over the uncoupling magnet or parked on a curve.
6. If cars will not uncouple, check to be sure the couplers are positioned directly adjacent to the magnet position indicator and that the indicator is placed in line with the center line of the under-track magnet.
7. Check that the magnet is secured to the underside of the track and fitted with the steel plate provided.

How to Run Your Train

1. Turn the knob on the speed controller clockwise until it stops (all the way to the left).
2. Plug in the power supply.
3. Begin feeding power to the track by slowly turning the knob on the speed controller clockwise.
4. Observe the direction of your train.
5. If it moves backwards when the controls indicate forward, stop the train.
6. Then simply disconnect, flip, and reconnect the terminal wire to the terminal rerailer track.
7. Remember – never leave your train running unattended!

Action Checklist (Troubleshooting If Your Train Doesn’t Run or Stops Running)

1. Is the power supply plugged in to a live receptacle?
2. Are the wheels on the track?
3. Is the wiring secure?
4. Is the track properly assembled?
5. Is the track properly seated in the rail joiner?
6. If your train stops or fails to start, a short circuit may be indicated. If this is the case, Unplug The Power Supply Immediately.
7. Common reasons for a short circuit: derailed wheels may cause a short. Check to make sure all wheels are on the track. Also check all connections and make sure there is no metal of any sort across the rails.
8. After checking everything carefully, resume operation.
9. Please note, your power supply is protected by a circuit breaker that automatically resets after a short circuit is corrected.
10. Allow up to 5 minutes for the circuit breaker to reset before resuming operation.

Keep Your Train in Top Operating Condition

1. Works better after couple hours of break-in time.
2. Train performs best under clean operating conditions.
3. Clean wheels and a clean track ensure good electrical contact.
4. After about every 8 hours of operation, wipe the track rails and exposed wheels with a soft, lint-free cloth.
5. Removal of black residue is normal.
6. Do Not Use Steel Wool To Clean Your Track.
7. Do not use common solvents, they may damage plastics - use track cleaner.
8. After 24 hours of use, light lubrication is required to keep train in top operating condition. Bachmann E-Z Lube or other hobby-grade lubricants are recommended.

Bachmann hopes you enjoy your train for many years to come!

Product description

Race along the riverside in luxury aboard the New York Central. Pulled by a powerful Berkshire locomotive, this heavyweight consist recalls the glory years of travel along the "Water Level Route."

• A LOCOMOTIVE SHOWSTOPPER – Checkout the luxurious New York Central Waterlevel Limited 2-8-4 set; This train is equipped with Bluetooth technology, letting you glide the rails via a mobile device; Great for kids, hobbyists and holiday decorating
• SET INCLUDES – 2-8-4 locomotive and tender; Two coaches; Observation car; Twelve 20” Radius MagneLock curves; three 9” Magnelock straights; one 9” MagneLock terminal section; 12V DC power supply, LionChief remote
• FEATURES – Controlled by remote, Bluetooth, DCC or DC transformer; Background, horn, bell, PA announcements and steam chuffing sounds; RailSounds RC sound system; Maintenance-free motor; Knuckle couplers; LED lighting; Fun Christmas announcements, more
• PRODUCT SPECIFICATIONS – HO Gauge compatible; minimum curve is 18” radius; Set length is 45”; Bluetooth, DCC or DC transformer compatible
• BATTERY REQUIREMENTS - Requires three AAA batteries to operate the LionChief remote control; Batteries are not included with purchase of train set

User questions & answers

Question:	how long is each train car
Answer:	No
Question:	Does it have smoke
Answer:	I doubt it. Only because of the width. the figures might float around at the waist. But if the figures are 8" high, then you might be fine.
Question:	Does it work with the black ez track I already have
Answer:	Yes, they will work on these figures, but the waist will be a little loose. For a snugger fit, try the 20SMB here: http://smile.amazon.com/Kaiser-Doll-Stand-20SMB-small-waisted/dp/B00TIYFDII/ref=sr_1_1?ie=UTF8&qid=1459432855&sr=8-1&keywords=kaiser+20smb
Question:	Does it work with Bachman track
Answer:	This particular stand would have a loose fit in the waist for a regular Barbie. Also, it may be too tall for LOLs.

Product features

Lionel New York Central Waterlevel Limited, Electric HO Gauge, Model Train Set with Remote and Bluetooth Capability

Race along the riverside in luxury aboard the New York Central. Pulled by a powerful Berkshire locomotive, this heavyweight consist recalls the glory years of travel along the "Water Level Route."

SET INCLUDES:

• 2-8-4 Locomotive and tender
• 2 Coaches
• Observation car
• Twelve 20" Radius MagneLock curves
• Three 9" MagneLock straights
• One 9" MageLock terminal section
• Wall pack power supply
• LionChief remote for locomotive

LOCOMOTIVE FEATURES:

• Electric locomotive controlled by remote, LionChief App, DCC or DC transformer
• Bluetooth equipped
• Locomotive and tender pick-ups for smooth operation
• RailSounds sound system with engine background and chuffing sounds, whistle and bell
• Operating directional headlight
• Operating directional tender light
• Easily convertible to other DCC decoders
• Sound ON/OFF switch
• Traction tires
• Powerful maintenance-free motor

Product description

5-Car "HO scale" Train - EMD GP40 diesel locomotive (with operating headlight) - open quad hopper- gondola- steel Reefer- off-center caboose body-mounted E-Z Mate couplers 47" X 38” oval track sets up in minutes includes signal bridge, 36 people figures, 24 telephone poles and 48 railroad and street signs includes Power pack, speed controller and plug-in terminal rerailer plugs into an AC outlet ages 14+

From the Manufacturer

You will command the rails with our striking Rail Chief set. Complete with miniature people and a signal bridge, this 130-piece set will let you oversee your own detailed railroading empire. This ready-to-run train set includes: EMD GP40 diesel locomotive with operating headlight, open quad hopper car, gondola car, steel reefer car, off-center caboose, 47" x 38" oval of snap-fit E-Z Track, including 12 pieces curved track, 1 piece straight track, and 1 plug-in terminal rerailer, signal bridge, 36 miniature people, 24 telephone poles, 48 railroad and street signs, power pack and speed controller.

• Complete Ready To Run 130 Piece Freight Train Set
• Powered by a EMD GP40 Diesel Locomotive with Operating Headlight
• Includes; Open Quad Hopper Car, Gondola Car, Steel Reefer Car, Off-Set Cupola Caboose, Signal Bridge, Miniature Figures, Railroad Signs, Street Signs, and Telephone Poles
• 47" x 38" Oval of Snap-Fit E-Z Track, Power Pack and Speed Controller
• HO Scale 1:87

User questions & answers

Question:	Is the transformer battery powered or plug-in
Answer:	That I do not know, but I would think so.
Question:	What are the measurements of the train cars
Answer:	yes
Question:	The age on this is 14 I'm looking for a train set for my 6 year old grandson. Is this really to advanced
Answer:	Yes, you can buy curved sections, straight sections, and left and right switches. I bought this set for my granddaughter (and I ) I think I paid $89 for the set and then on eBay bought about $75 of track. We made a really nice big layout with sidings and two loops. I’m very impressed with this set. I may be a little over the top, but I also found a couple of extra rail cars from the John Deere set on eBay to add to her Pennsylvania Flyer.
Question:	Is the engine plastic or metal
Answer:	There are switches

Product features

Discover Everything Bachmann Trains Offers to Get Started in Model Railroading

Since 1833, Bachmann has been known for providing innovative design at a good value. We are now one of the world's largest distributor, by volume, of ready-to-run train sets, locomotives, track, and accessories. Bachmann is also the only train company to offer products in all five of the most popular scales: N, HO, On30, O, and Large Scale.

As a distributor of beloved Thomas & Friends products, Bachmann brings the adventures of Thomas the Tank Engine to life with a growing line of complete train sets, separate sale items, and accessories for children from 8 to 80-just add your imagination. Thomas & Friends is available in both HO and Large Scale.

Bachmann's exclusive snap-together E-Z Track System makes track setup quick, easy, and fun. Plasticville U.S.A. and SceneScapes buildings and accessories let you add the finishing touches for the perfect layout.

If You Are Purchasing a Train Set, It Will Include

1. Locomotive
2. Cars (Rolling Stock)
3. E-Z Track – available in either black roadbed with steel alloy rail or gray roadbed with nickel silver rail
4. Terminal/Rerailer
5. Terminal Wire
6. Speed Controller
7. Power Supply
8. List of Components

Track Assembly

1. Decide where to set up your train – a dry, firm, flat surface works best!
2. To make sure you have enough working room, make a test track layout by loosely placing track in desired configuration.
3. The terminal/rerailer section will later be connected to a power pack and power supply, so place it near an outlet or power strip.
4. Install under-track magnet, if your set comes with one. If your set does not come with one, magnets are available separately (HO Item No. 78999; N Scale Item No. 78998).
5. Assemble the track by pushing together. Make sure the rail and joiners are seated properly. Be careful that the rail joiners do not slip under the rail without properly connecting. This can cause train derailments and electrical circuit interruptions.
6. After track is assembled, double-check for joint connection and fit by lightly running your fingers over the top of the rails in both directions.
7. If you detect bumps or distortion on the track surface, recheck the rail joiner fit.

Power Connections

1. Power supply and speed control are plug and play; no tools are needed.
2. Power is supplied to the track and the locomotive by the power supply, speed controller, terminal wire, and E-Z Track terminal/rerailer.
3. First – turn knob on the speed controller counterclockwise until it stops (all the way to the left).
4. Next – attach terminal wire to the speed controller by plugging it in where it says 'To Track.'
5. Then – plug terminal wire into the E-Z Track terminal rerailer. Firmly push connector onto the track terminals.
6. Finally – plug the connecting wire from the power supply into jack on the speed controller labeled 'In.' Then plug power supply into a live wall outlet.
7. Some sets may come with a speed controller with two push button connectors. These are used to supply AC power to accessories.
8. To make positive and secure connections to these, push in buttons and insert each of the bare ends of the connection wire from your accessory.
9. The speed controller is capable of powering one accessory at a time.

Putting the Train on the Track

1. Put the locomotive on the track and run the wheels back and forth over the terminal rerailer track.
2. When the wheels glide smoothly over the track, you know the wheels are all on the track. If your set comes with a tender, attach it to the locomotive.
3. Add the rest of the cars that come with your set by placing them on the track and running them back and forth over the terminal rerailer until they glide smoothly. Then gently push the cars together – they will engage automatically.
4. Do not try to connect cars when positioned over an under-track magnet.

How to Use E-Z Mate Couplers (HO and On30 Scale)

1. Your set may be equipped with E-Z Mate magnetically operated knuckle couplers that let you perform real railroad switching and yard operations.
2. Coupling two cars with E-Z Mate couplers is as easy as pushing them together when they are not over an under-track magnet.
3. Uncoupling occurs only when over an under-track magnet and when there is no tension between the cars.
4. To uncouple E-Z Mate couplers, stop two couplers directly over the under-track magnet. With no tension between the cars, the couplers will open automatically.
5. If cars will not couple, check to be sure cars are not positioned over the uncoupling magnet or parked on a curve.
6. If cars will not uncouple, check to be sure the couplers are positioned directly adjacent to the magnet position indicator and that the indicator is placed in line with the center line of the under-track magnet.
7. Check that the magnet is secured to the underside of the track and fitted with the steel plate provided.

How to Run Your Train

1. Turn the knob on the speed controller clockwise until it stops (all the way to the left).
2. Plug in the power supply.
3. Begin feeding power to the track by slowly turning the knob on the speed controller clockwise.
4. Observe the direction of your train.
5. If it moves backwards when the controls indicate forward, stop the train.
6. Then simply disconnect, flip, and reconnect the terminal wire to the terminal rerailer track.
7. Remember – never leave your train running unattended!

Action Checklist (Troubleshooting If Your Train Doesn’t Run or Stops Running)

1. Is the power supply plugged in to a live receptacle?
2. Are the wheels on the track?
3. Is the wiring secure?
4. Is the track properly assembled?
5. Is the track properly seated in the rail joiner?
6. If your train stops or fails to start, a short circuit may be indicated. If this is the case, Unplug The Power Supply Immediately.
7. Common reasons for a short circuit: derailed wheels may cause a short. Check to make sure all wheels are on the track. Also check all connections and make sure there is no metal of any sort across the rails.
8. After checking everything carefully, resume operation.
9. Please note, your power supply is protected by a circuit breaker that automatically resets after a short circuit is corrected.
10. Allow up to 5 minutes for the circuit breaker to reset before resuming operation.

Keep Your Train in Top Operating Condition

1. Works better after couple hours of break-in time.
2. Train performs best under clean operating conditions.
3. Clean wheels and a clean track ensure good electrical contact.
4. After about every 8 hours of operation, wipe the track rails and exposed wheels with a soft, lint-free cloth.
5. Removal of black residue is normal.
6. Do Not Use Steel Wool To Clean Your Track.
7. Do not use common solvents, they may damage plastics - use track cleaner.
8. After 24 hours of use, light lubrication is required to keep train in top operating condition. Bachmann E-Z Lube or other hobby-grade lubricants are recommended.

Bachmann hopes you enjoy your train for many years to come!

Product description

Rail transport has played a crucial role in successful U.S. military campaigns since the Civil War. Often serving as the logistical backbone of large operations, military trains deliver personnel, weapons, ammunition, and food to the troops in the field. With our Strike Force train, we honor the tireless efforts of our men and women in uniform. This ready-to-run train set includes: EMD GP40 diesel locomotive with operating headlight flat car with crates center-depressed flat car with camouflage missile offset cupola caboose body-mounted E-Z Mate(c) couplers 47" x 38" oval of snap-fit E-Z Track(c), including 12 pieces of curved track, 1 piece of straight track, and 1 plug-in terminal rerailer power pack and speed controller illustrated instruction manual WARNING: CHOKING HAZARD - SMALL PARTS! NOT INTENDED FOR CHILDREN UNDER 3.

• Complete Ready To Run Military Train Set
• Powered by a EMD GP40 Diesel Locomotive with Operating Headlight
• Includes; Flat Car with Crates, Center-Depressed Flat Car with Camouflage Missile, and Off-Set Cupola Caboose,
• 47" x 38" Oval of Snap-Fit E-Z Track, Power Pack and Speed Controller
• HO Scale 1:87

User questions & answers

Question:	Are the trains made of plastic or metal
Answer:	It is strictly a matter of preference. I have used a wooden pole and it works just fine and has for several years. Some people prefer steel or aluminum, they too are very good for outdoor applications. Could not say that I would choose one over the other. Sorry, but that is my personal assessment.
Question:	What does it mean HO scale
Answer:	This flag is very well made and the fabric is quite heavy. I live live near the Oklahoma panhandle where it is also windy most of the time. My flag is holding up just fine and so far looks still brand new.
Question:	is there a set call spcial forces
Answer:	Yes it will fit on either flag pole style

Product features

Discover Everything Bachmann Trains Offers to Get Started in Model Railroading

Since 1833, Bachmann has been known for providing innovative design at a good value. We are now one of the world's largest distributor, by volume, of ready-to-run train sets, locomotives, track, and accessories. Bachmann is also the only train company to offer products in all five of the most popular scales: N, HO, On30, O, and Large Scale.

As a distributor of beloved Thomas & Friends products, Bachmann brings the adventures of Thomas the Tank Engine to life with a growing line of complete train sets, separate sale items, and accessories for children from 8 to 80-just add your imagination. Thomas & Friends is available in both HO and Large Scale.

Bachmann's exclusive snap-together E-Z Track System makes track setup quick, easy, and fun. Plasticville U.S.A. and SceneScapes buildings and accessories let you add the finishing touches for the perfect layout.

If You Are Purchasing a Train Set, It Will Include

1. Locomotive
2. Cars (Rolling Stock)
3. E-Z Track – available in either black roadbed with steel alloy rail or gray roadbed with nickel silver rail
4. Terminal/Rerailer
5. Terminal Wire
6. Speed Controller
7. Power Supply
8. List of Components

Track Assembly

1. Decide where to set up your train – a dry, firm, flat surface works best!
2. To make sure you have enough working room, make a test track layout by loosely placing track in desired configuration.
3. The terminal/rerailer section will later be connected to a power pack and power supply, so place it near an outlet or power strip.
4. Install under-track magnet, if your set comes with one. If your set does not come with one, magnets are available separately (HO Item No. 78999; N Scale Item No. 78998).
5. Assemble the track by pushing together. Make sure the rail and joiners are seated properly. Be careful that the rail joiners do not slip under the rail without properly connecting. This can cause train derailments and electrical circuit interruptions.
6. After track is assembled, double-check for joint connection and fit by lightly running your fingers over the top of the rails in both directions.
7. If you detect bumps or distortion on the track surface, recheck the rail joiner fit.

Power Connections

1. Power supply and speed control are plug and play; no tools are needed.
2. Power is supplied to the track and the locomotive by the power supply, speed controller, terminal wire, and E-Z Track terminal/rerailer.
3. First – turn knob on the speed controller counterclockwise until it stops (all the way to the left).
4. Next – attach terminal wire to the speed controller by plugging it in where it says 'To Track.'
5. Then – plug terminal wire into the E-Z Track terminal rerailer. Firmly push connector onto the track terminals.
6. Finally – plug the connecting wire from the power supply into jack on the speed controller labeled 'In.' Then plug power supply into a live wall outlet.
7. Some sets may come with a speed controller with two push button connectors. These are used to supply AC power to accessories.
8. To make positive and secure connections to these, push in buttons and insert each of the bare ends of the connection wire from your accessory.
9. The speed controller is capable of powering one accessory at a time.

Putting the Train on the Track

1. Put the locomotive on the track and run the wheels back and forth over the terminal rerailer track.
2. When the wheels glide smoothly over the track, you know the wheels are all on the track. If your set comes with a tender, attach it to the locomotive.
3. Add the rest of the cars that come with your set by placing them on the track and running them back and forth over the terminal rerailer until they glide smoothly. Then gently push the cars together – they will engage automatically.
4. Do not try to connect cars when positioned over an under-track magnet.

How to Use E-Z Mate Couplers (HO and On30 Scale)

1. Your set may be equipped with E-Z Mate magnetically operated knuckle couplers that let you perform real railroad switching and yard operations.
2. Coupling two cars with E-Z Mate couplers is as easy as pushing them together when they are not over an under-track magnet.
3. Uncoupling occurs only when over an under-track magnet and when there is no tension between the cars.
4. To uncouple E-Z Mate couplers, stop two couplers directly over the under-track magnet. With no tension between the cars, the couplers will open automatically.
5. If cars will not couple, check to be sure cars are not positioned over the uncoupling magnet or parked on a curve.
6. If cars will not uncouple, check to be sure the couplers are positioned directly adjacent to the magnet position indicator and that the indicator is placed in line with the center line of the under-track magnet.
7. Check that the magnet is secured to the underside of the track and fitted with the steel plate provided.

How to Run Your Train

1. Turn the knob on the speed controller clockwise until it stops (all the way to the left).
2. Plug in the power supply.
3. Begin feeding power to the track by slowly turning the knob on the speed controller clockwise.
4. Observe the direction of your train.
5. If it moves backwards when the controls indicate forward, stop the train.
6. Then simply disconnect, flip, and reconnect the terminal wire to the terminal rerailer track.
7. Remember – never leave your train running unattended!

Action Checklist (Troubleshooting If Your Train Doesn’t Run or Stops Running)

1. Is the power supply plugged in to a live receptacle?
2. Are the wheels on the track?
3. Is the wiring secure?
4. Is the track properly assembled?
5. Is the track properly seated in the rail joiner?
6. If your train stops or fails to start, a short circuit may be indicated. If this is the case, Unplug The Power Supply Immediately.
7. Common reasons for a short circuit: derailed wheels may cause a short. Check to make sure all wheels are on the track. Also check all connections and make sure there is no metal of any sort across the rails.
8. After checking everything carefully, resume operation.
9. Please note, your power supply is protected by a circuit breaker that automatically resets after a short circuit is corrected.
10. Allow up to 5 minutes for the circuit breaker to reset before resuming operation.

Keep Your Train in Top Operating Condition

1. Works better after couple hours of break-in time.
2. Train performs best under clean operating conditions.
3. Clean wheels and a clean track ensure good electrical contact.
4. After about every 8 hours of operation, wipe the track rails and exposed wheels with a soft, lint-free cloth.
5. Removal of black residue is normal.
6. Do Not Use Steel Wool To Clean Your Track.
7. Do not use common solvents, they may damage plastics - use track cleaner.
8. After 24 hours of use, light lubrication is required to keep train in top operating condition. Bachmann E-Z Lube or other hobby-grade lubricants are recommended.

Bachmann hopes you enjoy your train for many years to come!

Product description

Pacific Flyer Ready To Run Electric Train Set - HO Scale. Assembly and breakdown of trains in the railway yard is tough work, but this 0-6-0 steam switcher is ready to get the job done. Assemble your consist, clear the yard and move your freight to its final destination with the Pacific Flyer! Watch the video to see the set in action! This ready-to-run train set includes: 0-6-0 steam locomotive and tender with operating headlight, gondola, box car, offset cupola caboose, body-mounted E-Z Mate couplers, 36" circle of snap-fit E-Z Track including 11 pieces of curved track and 1 curved plug-in terminal rerailer, power pack and speed control, illustrated instruction manual

From the Manufacturer

Assembly and breakdown of trains in the railway yard is tough work, but this 0-6-0 steam switcher is ready to get the job done. Assemble your consist, clear the yard and move your freight to its final destination with the Pacific Flyer.

• Complete Ready To Run Freight Train Set
• Powered by a 0-6-0 Steam Era Locomotive and Tender with Operating Headlight
• Includes; Gondola Car, Box Car, and Off-Set Cupola Caboose
• 36" Circle of Snap-Fit E-Z Track, Power Pack and Speed Controller
• HO Scale 1:87

User questions & answers

Question:	Is the Height 3 inches
Answer:	Hi there, The Adventure Town Railway train set is compatible with KidKraft, Brio® and Thomas & Friends Wooden Railway vehicles and play sets. Thank you for playing with KIdKraft!- The KidKraft Customer Care Team
Question:	does it have smoke
Answer:	If you contact the seller they might be able to assist you with any broken parts or pieces missing, that's generally what I do.
Question:	why does my train slow down when it gets to a certain point on the track
Answer:	Hi There, The bins on the Adventure Railway Train Set & Table do slide under on wooden rails designed to hold them. Thank you for Playing with KidKraft! The Kidkraft Customer Care Team
Question:	Does the train whistle
Answer:	I don't know for sure, but I think duplo are the same size and pattern as lego blocks. I bought the table for my grand-niece so I haven't actually seen it yet. Your answer might be to compare the specifications for legos and duplos at their manufacturers' sites. Sorry I can't be of more assistance, I had American Bricks and Lincoln Logs when I was a kid!

Product features

Discover Everything Bachmann Trains Offers to Get Started in Model Railroading

Since 1833, Bachmann has been known for providing innovative design at a good value. We are now one of the world's largest distributor, by volume, of ready-to-run train sets, locomotives, track, and accessories. Bachmann is also the only train company to offer products in all five of the most popular scales: N, HO, On30, O, and Large Scale.

As a distributor of beloved Thomas & Friends products, Bachmann brings the adventures of Thomas the Tank Engine to life with a growing line of complete train sets, separate sale items, and accessories for children from 8 to 80-just add your imagination. Thomas & Friends is available in both HO and Large Scale.

Bachmann's exclusive snap-together E-Z Track System makes track setup quick, easy, and fun. Plasticville U.S.A. and SceneScapes buildings and accessories let you add the finishing touches for the perfect layout.

If You Are Purchasing a Train Set, It Will Include

1. Locomotive
2. Cars (Rolling Stock)
3. E-Z Track – available in either black roadbed with steel alloy rail or gray roadbed with nickel silver rail
4. Terminal/Rerailer
5. Terminal Wire
6. Speed Controller
7. Power Supply
8. List of Components

Track Assembly

1. Decide where to set up your train – a dry, firm, flat surface works best!
2. To make sure you have enough working room, make a test track layout by loosely placing track in desired configuration.
3. The terminal/rerailer section will later be connected to a power pack and power supply, so place it near an outlet or power strip.
4. Install under-track magnet, if your set comes with one. If your set does not come with one, magnets are available separately (HO Item No. 78999; N Scale Item No. 78998).
5. Assemble the track by pushing together. Make sure the rail and joiners are seated properly. Be careful that the rail joiners do not slip under the rail without properly connecting. This can cause train derailments and electrical circuit interruptions.
6. After track is assembled, double-check for joint connection and fit by lightly running your fingers over the top of the rails in both directions.
7. If you detect bumps or distortion on the track surface, recheck the rail joiner fit.

Power Connections

1. Power supply and speed control are plug and play; no tools are needed.
2. Power is supplied to the track and the locomotive by the power supply, speed controller, terminal wire, and E-Z Track terminal/rerailer.
3. First – turn knob on the speed controller counterclockwise until it stops (all the way to the left).
4. Next – attach terminal wire to the speed controller by plugging it in where it says 'To Track.'
5. Then – plug terminal wire into the E-Z Track terminal rerailer. Firmly push connector onto the track terminals.
6. Finally – plug the connecting wire from the power supply into jack on the speed controller labeled 'In.' Then plug power supply into a live wall outlet.
7. Some sets may come with a speed controller with two push button connectors. These are used to supply AC power to accessories.
8. To make positive and secure connections to these, push in buttons and insert each of the bare ends of the connection wire from your accessory.
9. The speed controller is capable of powering one accessory at a time.

Putting the Train on the Track

1. Put the locomotive on the track and run the wheels back and forth over the terminal rerailer track.
2. When the wheels glide smoothly over the track, you know the wheels are all on the track. If your set comes with a tender, attach it to the locomotive.
3. Add the rest of the cars that come with your set by placing them on the track and running them back and forth over the terminal rerailer until they glide smoothly. Then gently push the cars together – they will engage automatically.
4. Do not try to connect cars when positioned over an under-track magnet.

How to Use E-Z Mate Couplers (HO and On30 Scale)

1. Your set may be equipped with E-Z Mate magnetically operated knuckle couplers that let you perform real railroad switching and yard operations.
2. Coupling two cars with E-Z Mate couplers is as easy as pushing them together when they are not over an under-track magnet.
3. Uncoupling occurs only when over an under-track magnet and when there is no tension between the cars.
4. To uncouple E-Z Mate couplers, stop two couplers directly over the under-track magnet. With no tension between the cars, the couplers will open automatically.
5. If cars will not couple, check to be sure cars are not positioned over the uncoupling magnet or parked on a curve.
6. If cars will not uncouple, check to be sure the couplers are positioned directly adjacent to the magnet position indicator and that the indicator is placed in line with the center line of the under-track magnet.
7. Check that the magnet is secured to the underside of the track and fitted with the steel plate provided.

How to Run Your Train

1. Turn the knob on the speed controller clockwise until it stops (all the way to the left).
2. Plug in the power supply.
3. Begin feeding power to the track by slowly turning the knob on the speed controller clockwise.
4. Observe the direction of your train.
5. If it moves backwards when the controls indicate forward, stop the train.
6. Then simply disconnect, flip, and reconnect the terminal wire to the terminal rerailer track.
7. Remember – never leave your train running unattended!

Action Checklist (Troubleshooting If Your Train Doesn’t Run or Stops Running)

1. Is the power supply plugged in to a live receptacle?
2. Are the wheels on the track?
3. Is the wiring secure?
4. Is the track properly assembled?
5. Is the track properly seated in the rail joiner?
6. If your train stops or fails to start, a short circuit may be indicated. If this is the case, Unplug The Power Supply Immediately.
7. Common reasons for a short circuit: derailed wheels may cause a short. Check to make sure all wheels are on the track. Also check all connections and make sure there is no metal of any sort across the rails.
8. After checking everything carefully, resume operation.
9. Please note, your power supply is protected by a circuit breaker that automatically resets after a short circuit is corrected.
10. Allow up to 5 minutes for the circuit breaker to reset before resuming operation.

Keep Your Train in Top Operating Condition

1. Works better after couple hours of break-in time.
2. Train performs best under clean operating conditions.
3. Clean wheels and a clean track ensure good electrical contact.
4. After about every 8 hours of operation, wipe the track rails and exposed wheels with a soft, lint-free cloth.
5. Removal of black residue is normal.
6. Do Not Use Steel Wool To Clean Your Track.
7. Do not use common solvents, they may damage plastics - use track cleaner.
8. After 24 hours of use, light lubrication is required to keep train in top operating condition. Bachmann E-Z Lube or other hobby-grade lubricants are recommended.

Bachmann hopes you enjoy your train for many years to come!

Product description

White Pass & Yukon ready to run Electric rain set - On30 scale - runs on HO scale track. Born out of the Klondike gold Rush of the 19th century, The white Pass & Yukon line has ably handled freight and passenger traffic for more than 100 years. Today, the wp&y thrives as a heritage railway, affording tourists close-up views of spectacular Alaskan scenery. The ready-to-run white Pass & Yukon comes complete with a 2-6-0 locomotive with operating headlight and tender with coal load, lighted combine, coach, and Observation Cars, 56" X 38" Oval of snap-fit nickel silver E-Z track, magnetically operated E-Z Mate couplers on all cars, power pack and speed controller, and illustrated instruction manual.

• Complete Ready To Run Passenger Train Set
• Powered by a 2-6-0 Steam Era Locomotive with Operating Headlight and Coal Tender
• Includes Lighted; Combine Car, Coach Car, and Observation Car
• 56" x 38" Oval of Nickel Silver E-Z Track, Power Pack and Speed Controller
• On30 Scale - O Scale Narrow Gauge Model That Runs on HO Track

User questions & answers

Question:	Does this train have DCC sound avaliable
Answer:	Plastic -Nicholas Smith Trains
Question:	Can i buy an extra passenger car for the yukon train set
Answer:	I think it means the pieces of a real life-size train are 87 times the size of an HO train . Thus a 5 inch long car of an HO train would correspone to a real car 435 inches or 36 ft 3 inches in length.
Question:	Does this train make smoke
Answer:	Maybe not available on here but there is one.
Question:	How can I order extra cars for this train set
Answer:	No pole, flag only.

Product features

Discover Everything Bachmann Trains Offers to Get Started in Model Railroading

Since 1833, Bachmann has been known for providing innovative design at a good value. We are now one of the world's largest distributor, by volume, of ready-to-run train sets, locomotives, track, and accessories. Bachmann is also the only train company to offer products in all five of the most popular scales: N, HO, On30, O, and Large Scale.

As a distributor of beloved Thomas & Friends products, Bachmann brings the adventures of Thomas the Tank Engine to life with a growing line of complete train sets, separate sale items, and accessories for children from 8 to 80-just add your imagination. Thomas & Friends is available in both HO and Large Scale.

Bachmann's exclusive snap-together E-Z Track System makes track setup quick, easy, and fun. Plasticville U.S.A. and SceneScapes buildings and accessories let you add the finishing touches for the perfect layout.

If You Are Purchasing a Train Set, It Will Include

1. Locomotive
2. Cars (Rolling Stock)
3. E-Z Track – available in either black roadbed with steel alloy rail or gray roadbed with nickel silver rail
4. Terminal/Rerailer
5. Terminal Wire
6. Speed Controller
7. Power Supply
8. List of Components

Track Assembly

1. Decide where to set up your train – a dry, firm, flat surface works best!
2. To make sure you have enough working room, make a test track layout by loosely placing track in desired configuration.
3. The terminal/rerailer section will later be connected to a power pack and power supply, so place it near an outlet or power strip.
4. Install under-track magnet, if your set comes with one. If your set does not come with one, magnets are available separately (HO Item No. 78999; N Scale Item No. 78998).
5. Assemble the track by pushing together. Make sure the rail and joiners are seated properly. Be careful that the rail joiners do not slip under the rail without properly connecting. This can cause train derailments and electrical circuit interruptions.
6. After track is assembled, double-check for joint connection and fit by lightly running your fingers over the top of the rails in both directions.
7. If you detect bumps or distortion on the track surface, recheck the rail joiner fit.

Power Connections

1. Power supply and speed control are plug and play; no tools are needed.
2. Power is supplied to the track and the locomotive by the power supply, speed controller, terminal wire, and E-Z Track terminal/rerailer.
3. First – turn knob on the speed controller counterclockwise until it stops (all the way to the left).
4. Next – attach terminal wire to the speed controller by plugging it in where it says 'To Track.'
5. Then – plug terminal wire into the E-Z Track terminal rerailer. Firmly push connector onto the track terminals.
6. Finally – plug the connecting wire from the power supply into jack on the speed controller labeled 'In.' Then plug power supply into a live wall outlet.
7. Some sets may come with a speed controller with two push button connectors. These are used to supply AC power to accessories.
8. To make positive and secure connections to these, push in buttons and insert each of the bare ends of the connection wire from your accessory.
9. The speed controller is capable of powering one accessory at a time.

Putting the Train on the Track

1. Put the locomotive on the track and run the wheels back and forth over the terminal rerailer track.
2. When the wheels glide smoothly over the track, you know the wheels are all on the track. If your set comes with a tender, attach it to the locomotive.
3. Add the rest of the cars that come with your set by placing them on the track and running them back and forth over the terminal rerailer until they glide smoothly. Then gently push the cars together – they will engage automatically.
4. Do not try to connect cars when positioned over an under-track magnet.

How to Use E-Z Mate Couplers (HO and On30 Scale)

1. Your set may be equipped with E-Z Mate magnetically operated knuckle couplers that let you perform real railroad switching and yard operations.
2. Coupling two cars with E-Z Mate couplers is as easy as pushing them together when they are not over an under-track magnet.
3. Uncoupling occurs only when over an under-track magnet and when there is no tension between the cars.
4. To uncouple E-Z Mate couplers, stop two couplers directly over the under-track magnet. With no tension between the cars, the couplers will open automatically.
5. If cars will not couple, check to be sure cars are not positioned over the uncoupling magnet or parked on a curve.
6. If cars will not uncouple, check to be sure the couplers are positioned directly adjacent to the magnet position indicator and that the indicator is placed in line with the center line of the under-track magnet.
7. Check that the magnet is secured to the underside of the track and fitted with the steel plate provided.

How to Run Your Train

1. Turn the knob on the speed controller clockwise until it stops (all the way to the left).
2. Plug in the power supply.
3. Begin feeding power to the track by slowly turning the knob on the speed controller clockwise.
4. Observe the direction of your train.
5. If it moves backwards when the controls indicate forward, stop the train.
6. Then simply disconnect, flip, and reconnect the terminal wire to the terminal rerailer track.
7. Remember – never leave your train running unattended!

Action Checklist (Troubleshooting If Your Train Doesn’t Run or Stops Running)

1. Is the power supply plugged in to a live receptacle?
2. Are the wheels on the track?
3. Is the wiring secure?
4. Is the track properly assembled?
5. Is the track properly seated in the rail joiner?
6. If your train stops or fails to start, a short circuit may be indicated. If this is the case, Unplug The Power Supply Immediately.
7. Common reasons for a short circuit: derailed wheels may cause a short. Check to make sure all wheels are on the track. Also check all connections and make sure there is no metal of any sort across the rails.
8. After checking everything carefully, resume operation.
9. Please note, your power supply is protected by a circuit breaker that automatically resets after a short circuit is corrected.
10. Allow up to 5 minutes for the circuit breaker to reset before resuming operation.

Keep Your Train in Top Operating Condition

1. Works better after couple hours of break-in time.
2. Train performs best under clean operating conditions.
3. Clean wheels and a clean track ensure good electrical contact.
4. After about every 8 hours of operation, wipe the track rails and exposed wheels with a soft, lint-free cloth.
5. Removal of black residue is normal.
6. Do Not Use Steel Wool To Clean Your Track.
7. Do not use common solvents, they may damage plastics - use track cleaner.
8. After 24 hours of use, light lubrication is required to keep train in top operating condition. Bachmann E-Z Lube or other hobby-grade lubricants are recommended.

Bachmann hopes you enjoy your train for many years to come!

Product description

This powerful Lehigh Valley inspired set is ready to go on an adventure throughout the Northeast. Once referred to the Route of the Black Diamond, named from the anthracite it transported, this Lehigh Valley set is a great way to begin your model railroad journey.

• Set Includes: Lehigh Valley U36B diesel locomotive, Lehigh Valley Map boxcar, Lehigh Valley 2-bay hopper, Lehigh Valley caboose, Eight pieces of O36 curved FasTrack, Two FasTrack 10" straight track sections, One LionChief FasTrack Terminal section, One Plug-Expand-Play Power Lock-on section, Wall-pack power supply, LionChief remote for locomotive
• Locomotive Features: Electric locomotive controlled by included LionChief remote, LionChief Universal Remote (sold separately) or Bluetooth LionChief app, On/Off switch for sound, RailSounds RC sound system with steam chuffing and background sounds, whistle, bell, and useractivated announcements, Operating headlight, Two Powerful maintenance-free motor, Operating couplers, Illuminated cab interior
• Freight Car Features: Operating couplers, Opening doors on boxcar
• LionChief Remote Features: Forward and reverse speed control knob, Three buttons to horn sound, bell, and special announcements, Requires three AAA alkaline batteries (not included)
• Minimum Curve: O31 | Set Length: 43" | Recommended Age: 10 years +

User questions & answers

Question:	Is this o scale. And does it adjust speed for up grades and down grades
Answer:	Yes, this is O Gauge, however the speed with not automatically adjust going up and down grades. -Nicholas Smith Trains
Question:	Can you turn the engine sound off
Answer:	Yes. Two ways. Under the engine there is a slide switch to turn off rail sounds. See Manuel for location. Second, with blue tooth under settings reduce volume and with remote see Manuel for procedure.
Question:	Where is place of manufacturing
Answer:	Last I knew, China was where most of the manufacturing was taking place. I remember reading that some painting and assembly was taking place in North Carolina but I can’t be 100% sure.

Product description

Santa Fe Flyer Ready To Run Electric Train Set - HO Scale. Hauling freight across the deserts, mountains, and cities of the American landscape is the Santa Fe Flyer. Powered by a mighty Santa Fe FT diesel locomotive with its distinctive “war bonnet” paint scheme, this sleek and powerful train deftly handles the ever-changing terrain of the Southwest United States. The Santa Fe Flyer includes: EMD FT diesel locomotive with operating headlight, open quad hopper, gondola, offset cupola caboose, body-mounted E-Z Mate couplers, 36" circle of snap-fit E-Z Track including 11 pieces of curved track and 1 curved plug-in terminal rerailer, power pack and speed controller, illustrated instruction manual.

From the Manufacturer

Hauling freight across the deserts, mountains, and cities of the American landscape is the Santa Fe Flyer. Powered by a mighty Santa Fe FT diesel locomotive with its distinctive war bonnet paint scheme, this sleek and powerful train deftly handles the ever-changing terrain of the Southwest United States.

• Complete Ready To Run Freight Train Set
• Powered by a EMD FT Diesel Locomotive with Operating Headlight
• Includes; Open Quad Hopper Car, Gondola Car, and Off-Set Cupola Caboose
• 36" Circle of Snap-Fit E-Z Track, Power Pack and Speed Controller
• HO Scale 1:87

User questions & answers

Question:	which is the width of the tracks? thx
Answer:	From tie to tieEnd is about two inches and from track to track it is 3/4 of an inch hope that helps you
Question:	Is this locomotive reasonably quiet
Answer:	Kids playing with the train make a lot of noise but the train is quiet.
Question:	does this train run on elect or is it batt opreated and what all comes with it
Answer:	Electric with a 12 volt DC supply. I would not buy a battery operated train.
Question:	can the track for this train be added to make it larger and if so how much more
Answer:	The track in this set is HO scale which is very popular. You can add as much track as you like to make many different layouts. Just look on Youtube for HO scale and see some very large realistic train layouts. You can buy HO track on line ot at many hobby shops. Prices vary.

Product features

Discover Everything Bachmann Trains Offers to Get Started in Model Railroading

Since 1833, Bachmann has been known for providing innovative design at a good value. We are now one of the world's largest distributor, by volume, of ready-to-run train sets, locomotives, track, and accessories. Bachmann is also the only train company to offer products in all five of the most popular scales: N, HO, On30, O, and Large Scale.

As a distributor of beloved Thomas & Friends products, Bachmann brings the adventures of Thomas the Tank Engine to life with a growing line of complete train sets, separate sale items, and accessories for children from 8 to 80-just add your imagination. Thomas & Friends is available in both HO and Large Scale.

Bachmann's exclusive snap-together E-Z Track System makes track setup quick, easy, and fun. Plasticville U.S.A. and SceneScapes buildings and accessories let you add the finishing touches for the perfect layout.

If You Are Purchasing a Train Set, It Will Include

1. Locomotive
2. Cars (Rolling Stock)
3. E-Z Track – available in either black roadbed with steel alloy rail or gray roadbed with nickel silver rail
4. Terminal/Rerailer
5. Terminal Wire
6. Speed Controller
7. Power Supply
8. List of Components

Track Assembly

1. Decide where to set up your train – a dry, firm, flat surface works best!
2. To make sure you have enough working room, make a test track layout by loosely placing track in desired configuration.
3. The terminal/rerailer section will later be connected to a power pack and power supply, so place it near an outlet or power strip.
4. Install under-track magnet, if your set comes with one. If your set does not come with one, magnets are available separately (HO Item No. 78999; N Scale Item No. 78998).
5. Assemble the track by pushing together. Make sure the rail and joiners are seated properly. Be careful that the rail joiners do not slip under the rail without properly connecting. This can cause train derailments and electrical circuit interruptions.
6. After track is assembled, double-check for joint connection and fit by lightly running your fingers over the top of the rails in both directions.
7. If you detect bumps or distortion on the track surface, recheck the rail joiner fit.

Power Connections

1. Power supply and speed control are plug and play; no tools are needed.
2. Power is supplied to the track and the locomotive by the power supply, speed controller, terminal wire, and E-Z Track terminal/rerailer.
3. First – turn knob on the speed controller counterclockwise until it stops (all the way to the left).
4. Next – attach terminal wire to the speed controller by plugging it in where it says 'To Track.'
5. Then – plug terminal wire into the E-Z Track terminal rerailer. Firmly push connector onto the track terminals.
6. Finally – plug the connecting wire from the power supply into jack on the speed controller labeled 'In.' Then plug power supply into a live wall outlet.
7. Some sets may come with a speed controller with two push button connectors. These are used to supply AC power to accessories.
8. To make positive and secure connections to these, push in buttons and insert each of the bare ends of the connection wire from your accessory.
9. The speed controller is capable of powering one accessory at a time.

Putting the Train on the Track

1. Put the locomotive on the track and run the wheels back and forth over the terminal rerailer track.
2. When the wheels glide smoothly over the track, you know the wheels are all on the track. If your set comes with a tender, attach it to the locomotive.
3. Add the rest of the cars that come with your set by placing them on the track and running them back and forth over the terminal rerailer until they glide smoothly. Then gently push the cars together – they will engage automatically.
4. Do not try to connect cars when positioned over an under-track magnet.

How to Use E-Z Mate Couplers (HO and On30 Scale)

1. Your set may be equipped with E-Z Mate magnetically operated knuckle couplers that let you perform real railroad switching and yard operations.
2. Coupling two cars with E-Z Mate couplers is as easy as pushing them together when they are not over an under-track magnet.
3. Uncoupling occurs only when over an under-track magnet and when there is no tension between the cars.
4. To uncouple E-Z Mate couplers, stop two couplers directly over the under-track magnet. With no tension between the cars, the couplers will open automatically.
5. If cars will not couple, check to be sure cars are not positioned over the uncoupling magnet or parked on a curve.
6. If cars will not uncouple, check to be sure the couplers are positioned directly adjacent to the magnet position indicator and that the indicator is placed in line with the center line of the under-track magnet.
7. Check that the magnet is secured to the underside of the track and fitted with the steel plate provided.

How to Run Your Train

1. Turn the knob on the speed controller clockwise until it stops (all the way to the left).
2. Plug in the power supply.
3. Begin feeding power to the track by slowly turning the knob on the speed controller clockwise.
4. Observe the direction of your train.
5. If it moves backwards when the controls indicate forward, stop the train.
6. Then simply disconnect, flip, and reconnect the terminal wire to the terminal rerailer track.
7. Remember – never leave your train running unattended!

Action Checklist (Troubleshooting If Your Train Doesn’t Run or Stops Running)

1. Is the power supply plugged in to a live receptacle?
2. Are the wheels on the track?
3. Is the wiring secure?
4. Is the track properly assembled?
5. Is the track properly seated in the rail joiner?
6. If your train stops or fails to start, a short circuit may be indicated. If this is the case, Unplug The Power Supply Immediately.
7. Common reasons for a short circuit: derailed wheels may cause a short. Check to make sure all wheels are on the track. Also check all connections and make sure there is no metal of any sort across the rails.
8. After checking everything carefully, resume operation.
9. Please note, your power supply is protected by a circuit breaker that automatically resets after a short circuit is corrected.
10. Allow up to 5 minutes for the circuit breaker to reset before resuming operation.

Keep Your Train in Top Operating Condition

1. Works better after couple hours of break-in time.
2. Train performs best under clean operating conditions.
3. Clean wheels and a clean track ensure good electrical contact.
4. After about every 8 hours of operation, wipe the track rails and exposed wheels with a soft, lint-free cloth.
5. Removal of black residue is normal.
6. Do Not Use Steel Wool To Clean Your Track.
7. Do not use common solvents, they may damage plastics - use track cleaner.
8. After 24 hours of use, light lubrication is required to keep train in top operating condition. Bachmann E-Z Lube or other hobby-grade lubricants are recommended.

Bachmann hopes you enjoy your train for many years to come!

Product description

This year, showcase the magic of Christmas with The Polar Express train set. Witness the children’s shadows as they sit in the passenger cars drinking steaming mugs of hot chocolate and chattering excitedly about Santa. This train is sure to make your home glow with Christmas spirit this season. You can operate this train using six conventional C batteries (not included)! The set also comes with an easy-to-operate RC remote control (requires three AAA batteries). With this Ready-to-Play set comes an exclusive track system which allows you to create; a circle, a rectangle or an oval layout. As this track system is exclusive to Ready-to-Play set, it is not compatible with Lionel G Gauge or other G Gauge track systems.

• This year showcase the magic of Christmas with the iconic Polar Express train set.
• Dimensions: 50" x 73.2" oval of Ready-to-Play track. 24 pieces of curved and 8 straight plastic track pieces. Fixed knuckle couplers.
• Remote Control: Buttons allow train to go forward and reverse, sound the whistle, ring the bell, and play announcements
• Batteries Required: Three AAA batteries for controller and six C cell batteries required for train (not included)
• The set includes a working headlight and 3 train cars. Witness the children’s shadows as they sit in the passenger cars.

User questions & answers

Question:	would this train set fit into a christmas village setup or is it too big? if the train is bigger than the homes it may not look right. If too large
Answer:	The bodies of the rolling stock are plastic, but the trucks and wheels are all die-cast metal. The engine is a mix of metal and plastic.
Question:	What is the difference between the ready to play set and ready and straight track pack
Answer:	Sorry , I really don't know !
Question:	Can you turn the sounds off
Answer:	Note that you'll need two different engineers. This train comes with engine 4520, make sure your second engine is a different number.
Question:	Are there cars and accessories that can be added to this train
Answer:	Plug-in with inline transformer

Product description

Thoroughbred Ready To Run Electric Train Set - HO Scale. Wheels rumble like the pounding of hooves as this iron horse rounds the bend. Hauling freight with the ease and grace of a champion, the Thoroughbred delivers fun and adventure to your stable of trains. View video to see this set in action. This ready-to-run train set includes: F7 diesel locomotive with operating headlight, open quad hopper, gondola, wide-vision caboose, body-mounted E-Z Mate couplers,47" x 38" oval of snap-fit E-Z Track including 12 pieces of curved track, 1 piece of straight track and 1 plug-in terminal rerailer, power pack and speed controller, illustrated instruction manual.

From the Manufacturer

Wheels rumble like the pounding of hooves as this iron horse rounds the bend. Hauling freight with the ease and grace of a champion the Thoroughbred delivers fun and adventure to your stable of trains.

• Complete Ready To Run Freight Train Set
• Powered by a F7 Diesel Locomotive with Operating Headlight
• Includes; Open Quad Hopper Car, Gondola Car, and Wide-Vision Caboose
• 47" x 38" Oval of Snap-Fit E-Z Track, Power Pack and Speed Controller
• HO Scale 1:87

User questions & answers

Question:	does the power pack work in australi
Answer:	If you guys use 220 volt, this will NOT work over there. This use 110 volt only.
Question:	is this train electric or battery powered remote controled
Answer:	110v transformer controls it. no batteries
Question:	Does the engine blow smoke
Answer:	No, the engine does not blow smoke. Usually only the steam engine replicas do and not all. If the train does have a "smoker" it will be clearly advertised on the package. It is an option many want so it will be promoted clearly on the packaging.
Question:	Can these trains pull more cars if I expand
Answer:	yes. he could pull 10 cars

Product features

Discover Everything Bachmann Trains Offers to Get Started in Model Railroading

Since 1833, Bachmann has been known for providing innovative design at a good value. We are now one of the world's largest distributor, by volume, of ready-to-run train sets, locomotives, track, and accessories. Bachmann is also the only train company to offer products in all five of the most popular scales: N, HO, On30, O, and Large Scale.

As a distributor of beloved Thomas & Friends products, Bachmann brings the adventures of Thomas the Tank Engine to life with a growing line of complete train sets, separate sale items, and accessories for children from 8 to 80-just add your imagination. Thomas & Friends is available in both HO and Large Scale.

Bachmann's exclusive snap-together E-Z Track System makes track setup quick, easy, and fun. Plasticville U.S.A. and SceneScapes buildings and accessories let you add the finishing touches for the perfect layout.

If You Are Purchasing a Train Set, It Will Include

1. Locomotive
2. Cars (Rolling Stock)
3. E-Z Track – available in either black roadbed with steel alloy rail or gray roadbed with nickel silver rail
4. Terminal/Rerailer
5. Terminal Wire
6. Speed Controller
7. Power Supply
8. List of Components

Track Assembly

1. Decide where to set up your train – a dry, firm, flat surface works best!
2. To make sure you have enough working room, make a test track layout by loosely placing track in desired configuration.
3. The terminal/rerailer section will later be connected to a power pack and power supply, so place it near an outlet or power strip.
4. Install under-track magnet, if your set comes with one. If your set does not come with one, magnets are available separately (HO Item No. 78999; N Scale Item No. 78998).
5. Assemble the track by pushing together. Make sure the rail and joiners are seated properly. Be careful that the rail joiners do not slip under the rail without properly connecting. This can cause train derailments and electrical circuit interruptions.
6. After track is assembled, double-check for joint connection and fit by lightly running your fingers over the top of the rails in both directions.
7. If you detect bumps or distortion on the track surface, recheck the rail joiner fit.

Power Connections

1. Power supply and speed control are plug and play; no tools are needed.
2. Power is supplied to the track and the locomotive by the power supply, speed controller, terminal wire, and E-Z Track terminal/rerailer.
3. First – turn knob on the speed controller counterclockwise until it stops (all the way to the left).
4. Next – attach terminal wire to the speed controller by plugging it in where it says 'To Track.'
5. Then – plug terminal wire into the E-Z Track terminal rerailer. Firmly push connector onto the track terminals.
6. Finally – plug the connecting wire from the power supply into jack on the speed controller labeled 'In.' Then plug power supply into a live wall outlet.
7. Some sets may come with a speed controller with two push button connectors. These are used to supply AC power to accessories.
8. To make positive and secure connections to these, push in buttons and insert each of the bare ends of the connection wire from your accessory.
9. The speed controller is capable of powering one accessory at a time.

Putting the Train on the Track

1. Put the locomotive on the track and run the wheels back and forth over the terminal rerailer track.
2. When the wheels glide smoothly over the track, you know the wheels are all on the track. If your set comes with a tender, attach it to the locomotive.
3. Add the rest of the cars that come with your set by placing them on the track and running them back and forth over the terminal rerailer until they glide smoothly. Then gently push the cars together – they will engage automatically.
4. Do not try to connect cars when positioned over an under-track magnet.

How to Use E-Z Mate Couplers (HO and On30 Scale)

1. Your set may be equipped with E-Z Mate magnetically operated knuckle couplers that let you perform real railroad switching and yard operations.
2. Coupling two cars with E-Z Mate couplers is as easy as pushing them together when they are not over an under-track magnet.
3. Uncoupling occurs only when over an under-track magnet and when there is no tension between the cars.
4. To uncouple E-Z Mate couplers, stop two couplers directly over the under-track magnet. With no tension between the cars, the couplers will open automatically.
5. If cars will not couple, check to be sure cars are not positioned over the uncoupling magnet or parked on a curve.
6. If cars will not uncouple, check to be sure the couplers are positioned directly adjacent to the magnet position indicator and that the indicator is placed in line with the center line of the under-track magnet.
7. Check that the magnet is secured to the underside of the track and fitted with the steel plate provided.

How to Run Your Train

1. Turn the knob on the speed controller clockwise until it stops (all the way to the left).
2. Plug in the power supply.
3. Begin feeding power to the track by slowly turning the knob on the speed controller clockwise.
4. Observe the direction of your train.
5. If it moves backwards when the controls indicate forward, stop the train.
6. Then simply disconnect, flip, and reconnect the terminal wire to the terminal rerailer track.
7. Remember – never leave your train running unattended!

Action Checklist (Troubleshooting If Your Train Doesn’t Run or Stops Running)

1. Is the power supply plugged in to a live receptacle?
2. Are the wheels on the track?
3. Is the wiring secure?
4. Is the track properly assembled?
5. Is the track properly seated in the rail joiner?
6. If your train stops or fails to start, a short circuit may be indicated. If this is the case, Unplug The Power Supply Immediately.
7. Common reasons for a short circuit: derailed wheels may cause a short. Check to make sure all wheels are on the track. Also check all connections and make sure there is no metal of any sort across the rails.
8. After checking everything carefully, resume operation.
9. Please note, your power supply is protected by a circuit breaker that automatically resets after a short circuit is corrected.
10. Allow up to 5 minutes for the circuit breaker to reset before resuming operation.

Keep Your Train in Top Operating Condition

1. Works better after couple hours of break-in time.
2. Train performs best under clean operating conditions.
3. Clean wheels and a clean track ensure good electrical contact.
4. After about every 8 hours of operation, wipe the track rails and exposed wheels with a soft, lint-free cloth.
5. Removal of black residue is normal.
6. Do Not Use Steel Wool To Clean Your Track.
7. Do not use common solvents, they may damage plastics - use track cleaner.
8. After 24 hours of use, light lubrication is required to keep train in top operating condition. Bachmann E-Z Lube or other hobby-grade lubricants are recommended.

Bachmann hopes you enjoy your train for many years to come!

Product description

Durango & Silverton Ready To Run Electric Train Set - N Scale. Built originally as a mining line, the scenic value of the Durango & Silverton was quickly recognized in passenger service. After surviving natural disasters, wars, and financial instability, a determined staff (and starring roles in several Hollywood movies) promoted the tourism that ensures the line's survival to this day. Now recognized as a National Historic Landmark and a National Historic Civil Engineering Landmark, the Durango & Silverton continues to provide year-round tourist service. Our N scale Durango & Silverton ready-to-run set comes complete with: 0-6-0 locomotive and tender, old-time combine, two old-time coaches, 34" x 24" oval of nickel silver E-Z Track, power pack and speed controller, illustrated instruction manual.

From the Manufacturer

Durango and Silverton - N Scale Ready to Run Electric Train Set. Built originally as a mining line, the scenic value of the Durango and Silverton was quickly recognized in passenger service. After surviving natural disasters, wars, and financial instability, a determined staff (and starring roles in several Hollywood movies) promoted the tourism that ensures the line's survival to this day. Now recognized as a National Historic Landmark and a National Historic Civil Engineering Landmark, the Durango and Silverton continues to provide year-round tourist service. Our N scale Durango and Silverton ready-to-run set comes complete with, 0-6-0 locomotive and tender, old-time combine, two old-time coaches, 34" x 24" oval of nickel silver E-Z Track, power pack and speed controller.

• Complete Ready To Run Old-Time Passenger Train Set
• Powered by a 0-6-0 Steam Era Locomotive with Tender
• Includes; Old-Time Combine Car, and Two Old-Time Coaches
• 34" x 24" Oval of Nickel Silver E-Z Track, Power Pack and Speed Controller
• N Scale 1:160
• Designed for Use by Experienced Hobbyist – Not Meant for Beginners
• Small Highly Detailed Components – For Consumers Ages 14 and Up
• NOTE: Refer to Instructional Video from the Image Section and the User Manual from the Technical Specification Before Use Which is Highly Essential.

User questions & answers

Question:	Is this a collectible? What justifies the price
Answer:	You can buy it anywhere, Amazon was best price. Its not a collectable, its just a fun western train
Question:	The description doesn't mention any buildings/people. Just checking if there is anything like that in this set? Thanks
Answer:	its just the train set - very nice looking.
Question:	Does this come dcc ready? that is can the board be changed to a dcc plug in board
Answer:	I bought this for my husband. He says no, it doesn't come dcc ready.
Question:	what is the radius on the curved track single piece 11.5 12 15 or 19 inches or
Answer:	It should be 11.5" radius.

Product features

Discover Everything Bachmann Trains Offers to Get Started in Model Railroading

Since 1833, Bachmann has been known for providing innovative design at a good value. We are now one of the world's largest distributor, by volume, of ready-to-run train sets, locomotives, track, and accessories. Bachmann is also the only train company to offer products in all five of the most popular scales: N, HO, On30, O, and Large Scale.

As a distributor of beloved Thomas & Friends products, Bachmann brings the adventures of Thomas the Tank Engine to life with a growing line of complete train sets, separate sale items, and accessories for children from 8 to 80-just add your imagination. Thomas & Friends is available in both HO and Large Scale.

Bachmann's exclusive snap-together E-Z Track System makes track setup quick, easy, and fun. Plasticville U.S.A. and SceneScapes buildings and accessories let you add the finishing touches for the perfect layout.

If You Are Purchasing a Train Set, It Will Include

1. Locomotive
2. Cars (Rolling Stock)
3. E-Z Track – available in either black roadbed with steel alloy rail or gray roadbed with nickel silver rail
4. Terminal/Rerailer
5. Terminal Wire
6. Speed Controller
7. Power Supply
8. List of Components

Track Assembly

1. Decide where to set up your train – a dry, firm, flat surface works best!
2. To make sure you have enough working room, make a test track layout by loosely placing track in desired configuration.
3. The terminal/rerailer section will later be connected to a power pack and power supply, so place it near an outlet or power strip.
4. Install under-track magnet, if your set comes with one. If your set does not come with one, magnets are available separately (HO Item No. 78999; N Scale Item No. 78998).
5. Assemble the track by pushing together. Make sure the rail and joiners are seated properly. Be careful that the rail joiners do not slip under the rail without properly connecting. This can cause train derailments and electrical circuit interruptions.
6. After track is assembled, double-check for joint connection and fit by lightly running your fingers over the top of the rails in both directions.
7. If you detect bumps or distortion on the track surface, recheck the rail joiner fit.

Power Connections

1. Power supply and speed control are plug and play; no tools are needed.
2. Power is supplied to the track and the locomotive by the power supply, speed controller, terminal wire, and E-Z Track terminal/rerailer.
3. First – turn knob on the speed controller counterclockwise until it stops (all the way to the left).
4. Next – attach terminal wire to the speed controller by plugging it in where it says 'To Track.'
5. Then – plug terminal wire into the E-Z Track terminal rerailer. Firmly push connector onto the track terminals.
6. Finally – plug the connecting wire from the power supply into jack on the speed controller labeled 'In.' Then plug power supply into a live wall outlet.
7. Some sets may come with a speed controller with two push button connectors. These are used to supply AC power to accessories.
8. To make positive and secure connections to these, push in buttons and insert each of the bare ends of the connection wire from your accessory.
9. The speed controller is capable of powering one accessory at a time.

Putting the Train on the Track

1. Put the locomotive on the track and run the wheels back and forth over the terminal rerailer track.
2. When the wheels glide smoothly over the track, you know the wheels are all on the track. If your set comes with a tender, attach it to the locomotive.
3. Add the rest of the cars that come with your set by placing them on the track and running them back and forth over the terminal rerailer until they glide smoothly. Then gently push the cars together – they will engage automatically.
4. Do not try to connect cars when positioned over an under-track magnet.

How to Use E-Z Mate Couplers (HO and On30 Scale)

1. Your set may be equipped with E-Z Mate magnetically operated knuckle couplers that let you perform real railroad switching and yard operations.
2. Coupling two cars with E-Z Mate couplers is as easy as pushing them together when they are not over an under-track magnet.
3. Uncoupling occurs only when over an under-track magnet and when there is no tension between the cars.
4. To uncouple E-Z Mate couplers, stop two couplers directly over the under-track magnet. With no tension between the cars, the couplers will open automatically.
5. If cars will not couple, check to be sure cars are not positioned over the uncoupling magnet or parked on a curve.
6. If cars will not uncouple, check to be sure the couplers are positioned directly adjacent to the magnet position indicator and that the indicator is placed in line with the center line of the under-track magnet.
7. Check that the magnet is secured to the underside of the track and fitted with the steel plate provided.

How to Run Your Train

1. Turn the knob on the speed controller clockwise until it stops (all the way to the left).
2. Plug in the power supply.
3. Begin feeding power to the track by slowly turning the knob on the speed controller clockwise.
4. Observe the direction of your train.
5. If it moves backwards when the controls indicate forward, stop the train.
6. Then simply disconnect, flip, and reconnect the terminal wire to the terminal rerailer track.
7. Remember – never leave your train running unattended!

Action Checklist (Troubleshooting If Your Train Doesn’t Run or Stops Running)

1. Is the power supply plugged in to a live receptacle?
2. Are the wheels on the track?
3. Is the wiring secure?
4. Is the track properly assembled?
5. Is the track properly seated in the rail joiner?
6. If your train stops or fails to start, a short circuit may be indicated. If this is the case, Unplug The Power Supply Immediately.
7. Common reasons for a short circuit: derailed wheels may cause a short. Check to make sure all wheels are on the track. Also check all connections and make sure there is no metal of any sort across the rails.
8. After checking everything carefully, resume operation.
9. Please note, your power supply is protected by a circuit breaker that automatically resets after a short circuit is corrected.
10. Allow up to 5 minutes for the circuit breaker to reset before resuming operation.

Keep Your Train in Top Operating Condition

1. Works better after couple hours of break-in time.
2. Train performs best under clean operating conditions.
3. Clean wheels and a clean track ensure good electrical contact.
4. After about every 8 hours of operation, wipe the track rails and exposed wheels with a soft, lint-free cloth.
5. Removal of black residue is normal.
6. Do Not Use Steel Wool To Clean Your Track.
7. Do not use common solvents, they may damage plastics - use track cleaner.
8. After 24 hours of use, light lubrication is required to keep train in top operating condition. Bachmann E-Z Lube or other hobby-grade lubricants are recommended.

Bachmann hopes you enjoy your train for many years to come!

Product description

Create the perfect Winter Wonderland in your own home this holiday season with Lionel’s Winter Wonderland Railroad Ready-to-Run train set. This set is guaranteed to get you into the Christmas spirit with its beautiful white 0-8-0 steam locomotive pulling festive green and red rolling stock. This set also comes with a 40 " x 60 " oval of White FasTrack, making it a truly special set to add to your holidays.

• Set Includes: Winter Wonderland 0-8-0 Steam Locomotive and tender, Sleigh Bells & Co. boxcar, Whimsical Winter Mix tank car, Winter Wonderland caboose, Featuring white FasTrack!, Eight pieces of O36 curved FasTrack, Two FasTrack 10" straight track sections, One LionChief FasTrack Terminal section, One, Plug-Expand-Play Power Lock-on section, Wall-pack power supply, LionChief remote for locomotive
• Locomotive Features: Electric locomotive controlled by included LionChief remote, LionChief UniversalRemote (sold separately) or Bluetooth LionChief app, On/Off switch for sound, RailSounds RC sound system with steam chuffing and background sounds, whistle, bell, and user-activated announcements, Operating headlight, Powerful maintenance-free motor, Operating couplers, Puffing smoke
• Freight Car Features: Operating couplers, Opening doors on boxcar
• LionChief Remote Features: Forward and reverse speed control knob, Three buttons to whistle sound, bell, and special announcements, Requires three AAA alkaline batteries (not included)
• Minimum Curve: O31 | Set Length: 45" | Recommended Age: 10 years +

User questions & answers

Question:	Does this set need extra tracks to fit around a “typical” Christmas tree? Or, does it come with a sufficient amount
Answer:	SET INCLUDES: Winter Wonderland 0-8-0 Steam Locomotive and tender Sleigh Bells & Co. boxcar Whimsical Winter Mix tank car Winter Wonderland caboose Featuring white FasTrack®! Eight pieces of O36 curved FasTrack® Two FasTrack® 10" straight track sections One LionChief® FasTrack® Terminal section One Plug-Expand-Play® Power Lock-on section Wall-pack power supply LionChief® Remote for locomotive with forward and reverse control, sounds and announcements
Question:	What come with the train set
Answer:	it says built by lionel 2019
Question:	Is this dated 2019 anywhere
Answer:	You can change volume with remote, hold down the speaker button in middle then turn knob to left to turn down or right to turn up.
Question:	How do change the volume with this train set
Answer:	Quality construction. good sound effects. There is not a "toy" feel to this product. this is my first model trail since childhood and it fills the bill nicely.

Product description

Versatile and reliable power for your railroad, no matter how you choose to run it! These Berkshires are loaded with the latest in control features, operating on either TMCC Command Control, Bluetooth via the Universal Remote or LionChief App, or conventional transformer. With die cast bodies, powerful motors, speed control, ElectroCouplers and RailSounds, these locomotives will perform as well as they look.

• control features: lc+ 2.0 control - operate with bluetooth using universal remote or lionchief app on your smart device or via your tmcc/legacy cab or conventional transformer
• set includes: die-cast boiler, frame, tender body, powerful maintenance-free motor, speed control, fan-driven smoke, numberboards, crew figures
• lighting & sound features: led headlight, electrocoupler on tender, flickering firebox, cab light, directional lighting, marker lights, ditch lights, strobe lights, mars lights, four chuffs/revs, volume control, background sounds, whistle/horn, legacy railsounds sound system featuring: crewtalk dialog and towercom announcements, each with different scenarios depending on whether the locomotive is in motion or stopped, single hit or continuous mechanical bell sounds
• "locomotive features: six official railroad speeds with crewtalk dialog, eight diesel rpm levels, legacy "real-time quilling horn" control with instant response for realistic signature "quilling" and correctly timed warning signals, sequence control: plays the sound effects of an entire trip, including warning sounds and announcements, based on the movement and speed of the locomotive, current speed and fuel dialog, refueling sound effects"
• "set length: 20", minimum curve: o31, recommended age: 10+ years"
• Skill level: All

User questions & answers

Question:	Does the magnalock track work well directly on carpet
Answer:	The Lionel Thomas and Lion Chief comes with a wall power pack which is smaller but just as efficient as the traditional heavy transformer. This set is also equipped with blue tooth, allowing you to run your train set with your smart phone instead of the remote control if you so choose.
Question:	Does the set come with the cars in the picture
Answer:	The remote control requires 3 AAA batterie.
Question:	Does this set come with all seven pieces shown in the photo or just the boiler and tender
Answer:	Yes! It is very kid friendly. It is a beautiful train!
Question:	Can someone please put up some pictures of this train set. Thank you
Answer:	My husband only uses FasTrack and it ran with no issues on that. I comes with its own tracks.