13 best honeywell carbon monoxide detectors

Product description

The 5800CO is a 3V battery powered wireless carbon monoxide (CO) detector intended for use with Honeywell alarm systems that support 5800 Series wireless devices. It provides early warning when its electrochemical sensing technology measures carbon monoxide levels in the air. The 5800CO is specifically designed for system operation and is fully listed to UL 2075 as a system supervised detector.* It contains a piezoelectric horn which generates the ANSI S3.41 temporal 4 pattern in an alarm condition. The detector consists of an electrochemical carbon monoxide sensor assembly coupled with a wireless transmitter. The transmitter can send alarm, trouble, end-of-life, tamper and low battery condition messages to the alarm panel. Since there are no holes to drill or wires to run, you can preserve the beauty of the home or building while protecting its occupants from harmful carbon monoxide gas. The 5800CO is an ideal carbon monoxide detector for difficult to wire locations, applications where room aesthetics are critical or where hazardous materials exist.

• Electrochemical Sensing Technology
• Local Sounder
• LED Status Indicators
• End of Life Timer
• Full Supervision

User questions & answers

Question:	My old 5800co was installed by the per mar company. do i need to have them install and program the new unit into the box or can i do it myself
Answer:	It should as dampers are simply 24 volt motors
Question:	How long will these units last
Answer:	As an HVAC Tech from 1976, I have installed quite a number of these. Here's your example: Zone 1 is calling for heat. Then zone 2 asks for the fan. Zone 1 will do it's heat cycle, turn off the heat and purge for the time set in the panel. After the purge, zone 2 damper opens and all other close unless there is a call for temperature change. On a call from any zone, it's damper opens, all others- not also calling- close and when satisfied the dampers for satisfied zones close one at a time until the last zone call finishes. Again at that time, the damper holds, purges, then all open unless a call for 'fan' is engaged, which runs the fan and opens the corresponding damper. One other thing to clarify: What happens if IE; Zone 1 is calling for heat, then zone 2 calls for cool? It heats Zone one until satisfied, or 20 minutes-whichever comes first. Then purges and allows the call for cooling. If the call for heat was interrupted and is still calling, it repeats the 20 minute or until satisfied routine and returns to heat on zone 1. (Using zone 1 and zone 2 just for the example, it can be any combination of zones and calls for heat/fan/cool)
Question:	What is the end of life date on this one
Answer:	The controller works on a first come-first served basis. If heat was requested first the system will turn on the heat until that thermostat reaches the desired temperature. It will then turn on the cooling to satisfy the thermostat requesting cooling. The automatic zone dampers that are required to work with this system are designed to provide the heated\cooled air only to the correct zone and should be set to open and close based upon the thermostat that is actually be provided conditioned air. So if thermostat 1 is requesting heat and is the first served, the dampers for thermostat 2 that are requesting cooling should be closed while the system is producing heated air.
Question:	Can you use this with a wired system to add other detectors to the system
Answer:	I think u need a separate thermostat for each zone. E.g. upstairs, main floor & basement. That's how mine is set up. Definitely recommend programmable with timer

Product description

Honeywells 5808W3 is a 3V lithium powered, photoelectronic smoke/heat detector with a built-in wireless transmitter. It is intended for use with any 5800 Series Wireless Receiver/Transceiver for residential installations (for commercial installations, the 5881ENHC or the 5883H receiver is required).



The transmitter can send alarm, tamper, maintenance (when control panels are equipped to process maintenance signals), and battery condition messages to the systems receiver. Smoothing algorithms minimize nuisance alarms by smoothing out short term spikes from dust and smoke, virtually eliminating nuisance alarms.



Since there are no holes to drill or wires to run, you can preserve the beauty of the building while protecting it. The 5808W3 is an ideal smoke detector for those difficult to wire locations, applications where room aesthetics are critical, or where hazardous materials exist.



All models also feature a restorable, builtin, fixed temperature (135F) thermal detector that is also capable of sensing a pre-freeze condition if the temperature is below 41F.

• Improved Robust RF Field Strength: The distance between the detector and receiver has been significantly increased without the need for a repeater
• Smart Check: A signal is sent to the control panel when the detector requires cleaning. This allows a regular nonemergency service call to clean the detector before it goes into alarm.
• Approved UL Listings for Residential and Commercial Applications: Both residential and commercial installation requirements are met
• Additional LED Status Indicators: Identifying between alarm or trouble conditions is a snap with green and red LED status indicators. A green LED denotes a normal condition while the red LED indicates abnormal conditions.
• Easy to install Mounting Base: The sturdy mounting base allows the detector to be more easily installed on uneven surfaces (i.e. stucco). The mounting base has larger mounting ports which accommodate drywall anchors for easy surface mounting.

User questions & answers

Question:	can this smoke detector also be hard wired
Answer:	Short answer; yes. Long answer; you'll need an additional power converter to give you 3 volts DC. Then connect the two wires to the two battery tabs and then mount. So for example, get a 120 volt to 3 volt DC wall power adapter and connect the wires. Anything with a battery can be converted into hardwired, you just need to provide the needed voltage from an external power source.
Question:	Can Honeywell products compatible with Vivant home security
Answer:	More than likely you have got a 2gig alarm panel from Vivint. If you have a 2gig alarm panel, then yes this device will work with your alarm system. That is all I can tell you as far as compatibility.
Question:	will this work with a 2gig system
Answer:	I actually hadn't tried it. According to one of Alarm Grid's videos on YouTube I believe it will work though.
Question:	how long does the batter last
Answer:	Batter usally last a couple of days or until you bake it. As for the batteries ho they should last a few years.

• 10-Year Battery & 10-Year Sensor: This smoke and carbon monoxide alarm provides 10 years of continuous power with a built-in lithium battery, saving on energy while remaining eco-friendly; saves you from constantly having to change batteries; an end-of-life signal will let you know when it's time to replace the unit for safety
• Practical LCD Display: Clearly indicates real-time carbon monoxide (CO) concentration in the surrounding air, as well as the remaining battery life and working status of the alarm; if a CO concentration of 30-999 ppm exists for a certain time period, the screen will be backlit blue, and the LED indicator will flash red 4 times every 5.8 seconds
• 2-in-1 Accurate, Reliable & Highly Sensitive Alarm: Equipped with both photoelectric smoke sensor and electrochemical CO sensor that work independently of each other; every second counts; detects both fast and slow-burning fires, and instantly notifies you when dangerous smoke or CO concentration is detected while minimizing false alarms; provides the ultimate protection from 2 deadly threats, all contained in 1 unit
• Simple to Use: Test/Silence button enables you to test the alarm weekly, and to easily silence the alarm when false alarms occur; malfunction and low battery warnings allow you to easily know the working status of the alarm; in case of an emergency, an alarm tone of over 85 dB will sound throughout your entire home, instantly alerting the entire household, even those in sleep
• Quick & Easy Installation with Guaranteed Quality: Requires no rewiring; easy to mount on any wall or ceiling with the included mounting bracket, screws and anchor plugs; certified to meet the UL 217 & UL 2034 safety standards for your peace of mind and absolute confidence in our product

Product features

When the LED indicator flashes RED, an alarm will sound, indicating one of the following four modes:

1. Smoke Alarm Mode: flashes red with 3 long beeps every 1.5 seconds.
2. CO Alarm Mode: flashes red with 4 quick beeps (every 5.8 seconds for the first 4 minutes, and every 60 seconds after 4 minutes).
3. Test Mode: flashes red with 2 sets of 3 long beeps, followed by 2 sets of 4 quick beeps.
4. Silence Mode: flashes red once every 5 seconds (no beeps).

When the LED indicator flashes YELLOW, it is important to check the working status of the alarm. There are three possible scenarios:

1. Low Battery Warning: flashes yellow with 1 beep every 60 seconds.
2. Smoke Malfunction Warning: flashes yellow 1 or 2 times with 2 beeps every 40 seconds.
3. CO Malfunction Warning: flashes yellow 3 or 4 times with 2 beeps every 40 seconds.

The LED indicator flashes GREEN to indicate the following three working modes (no beeps):

1. Standby Mode: flashes green once every 60 seconds.
2. Exiting Alarm Mode: flashes green once per second for 5 seconds.
3. Exiting Silence Mode: flashes green 3 times.

Practical LCD Display

• The display will indicate real-time carbon monoxide (CO) concentration in the surrounding air, as well as the remaining battery life and working status of the alarm.
• If a CO concentration of 30-999 ppm exists for a certain time period,the screen will be backlit blue, and the LED indicator will flash red 4 times every 5.8 seconds.

Technical Specifications

Power Supply: 10-year sealed lithium battery

Smoke Sensor Type: Photoelectric

CO Sensor Type: Electrochemical

Product Life: About 10 years

Safety Standards: UL 217 & UL 2034

Alarm Noise Level: 85 dB at 9.84 ft (3 m)

Product description

Honeywell 5800 series wireless smoke/co detector. This unit is to be installed into any Honeywell brand wireless security system that accepts 5800 series wireless sensors. This unit has a ten year life due to co detection.

• 5800COMBO Wireless Combination Photoelectric Smoke/Carbon Monoxide (CO) Detector for use with Honeywell's 5800 Series

User questions & answers

Question:	I already have standard smoke/co detectors in my house. Do I replace all my detectors with this model or does one of these integrate with others
Answer:	no
Question:	Can it fit into 5800CO base
Answer:	There are three settings, easy, medium, and hard. The game eases you in with easier stuff first. There is also a track just to practice.
Question:	Can this unit be hardwired
Answer:	It automatically comes up when you activate a 2nd controller.
Question:	If i install multiple of these on my Vista panel will they sink up and sound together like the Nest combo or does only one go off
Answer:	Yes it will, but you may not be able to access downloadable content.

Product description

ProSeries Wireless Combination Smoke/Heat/Carbon Monoxide Detector. The PROSiXCOMBO is a two-way, professionally monitored, wireless, combination smoke/heat and carbon monoxide (CO) detector. Multi-Threat Detection The Honeywell Home SIXCOMBO from Resideo is a two-way wireless smoke and carbon monoxide detector with four sensing elements that improve detection while reducing false alarms. This smart home security system device is equipped with a battery pull-tab and auto-enrollment for easy installation.

• ProSeries Wireless Combination Smoke/Heat/Carbon Monoxide Detector

Product description

Fend all Flash Flood utilizes sealed cartridges that contain one gallon of preserved and pH balanced Spherion Saline solution. The Fend all Flash Flood delivery system offers immediate, hands-free eye flushing, and is portable to meet the needs of changing work-place hazards. Removing the pull strap easily activates the system, while dual nozzles provide flushing to both eyes simultaneously. When activated, Fend all Flash Flood delivers saline solution for three minutes.

User questions & answers

Question:	Which multi gas alibration tank works with this unit
Answer:	H2s tank is what I use to check and calibrate with; however, I have not had a change in calibration results in over a year on these. We have a half of dozen in service and some other models and this I by far the best.
Question:	Does the Multi-Air Gas Detector come with the case which includes the charger, calibration gas, and attachment
Answer:	charger and hose attachment for calibration only....no gas can included.

Product description

• Single-gas detector for surveying levels of carbon monoxide (CO) in natural and industrial environments, and in other personal safety, training, research, and ambient air monitoring applications
• Electrochemical cell sensor monitors ambient carbon monoxide levels continuously for up to two years without requiring unit calibration, recharging, or battery replacement
• Audio, visual, and vibration alarms alert simultaneously when carbon monoxide gas reaches factory-set low or high levels
• LCD screen shows self-test status, high and low alarm set-points, maximum exposure, gas type, alarm level (low or high), detector life remaining, and time since last maximum exposure
• Back-mounted alligator clip allows wearing the unit on a belt, and a concussion-resistant boot helps protect against damage

User questions & answers

Question:	As for the calibration, how long does that take? Will the unit need to be shipped out to Honeywell for calibration service
Answer:	They come pre-calibrated, but you can bump test them and recalibrate them yourself following the instructions via the manual.
Question:	Does this unit come with calibration document at time of purchase
Answer:	Yes it does
Question:	It indicates a 2 year life, does this mean it goes in the trash after that
Answer:	If you chose to, the 2 year is a calibration limit, the device will continue to function until the battery dies, for the price of the unit vs a monthly calibration we just throw it away and get a new one, I do not think they can be re-calibrated and I don't know how long after the 2year countdown ends it will continue to operate but ours still worked when I disposed of them. Rules require us to maintain current calibrations on our gas meters so I throw it away and get new.
Question:	I need owners manual how do I get it
Answer:	http://www.honeywellanalytics.com/en/products/GasAlert-Extreme

Product description

'Carbon Monoxide Sensor Cartridge, Fits Brand VULCAIN'

• CARBON MONOXIDE
• SENSOR CARTRIDGE
• Sensor Module/Housing
• Sensors & Switches

Product description

Single Gas Detector, CO, 0-1000 ppm, EU, Blk This listing is for each. Technical Specification Item Single Gas Detector, Europe, Black Gas Type CO Detects Carbon Monoxide Sensor Range 0 to 1000 ppm Resolution 1 ppm Operating Temp. Range -20 Degrees to +50 Degrees C, -4 Degrees to +122 Degrees F Alarm Setting Low 30 ppm, High 200 ppm Alarm Type Audible, Vibrating, Visual Battery Type 4.2 V Lithium Battery Life 2 yr Display LCD Interchangeable Sensors Yes Height 5 1/2 in Width 2 13/16 in Depth 1 13/16 in Standards CSA: Class 1, Div.1, Gr. A, B, C, D -- IECEx: Ga Ex ia IIC T4 -- ATEX: CE EX II 1 G Ga Ex ia IIC T4 -- INMETRO Br Ex Ia IIC T11 Features Continuous LCD Shows Real-Time Gas Concentrations, Compact and Lightweight Design Makes it Comfortable to Wear, Water-Resistant, Simple Automatic Calibration Procedure, Compatabile with BW Microdock II Automatic Test and Calibration Station, Full Function Self-Test Of Sensor, Battery Status, Circut Integrity and Audible/Visual Alarms On Start Up, Bright Wide-Angled Visual Alarm Bars, Built-In Concussion-Proof Boot. Includes Detector Complete with Specified Sensor(s), Stainless Steel Alligator Clip and Concussion-Proof Housing, Rechargeable Lithium Polymer Battery, Charging Adapter, 3 ft/1m Calibration Hose with Quick Connect, 10 ft/3m Sampling Hose with Particulate Filter and Quick Connect, Reversable Screwdriver, Kit of Spare Pump Filters, Manual, Multi-Language CD Manual Hazardous Material - General

• Single Gas Detector, CO, 0-1000 ppm, EU, Blk This listing is for each

Product description

BW Technologies replacement MICROceL carbon monoxide CO sensor for GasAlertMicroClip XT and GasAlertMax XT II gas detectors. 0 to 500 ppm measuring range. 1 ppm resolution. 2 year warranty.

• Replacement MICROceL carbon monoxide CO sensor for GasalertMicroClip XT and GasAlertMax XT II gas detectors
• 0 to 500 ppm measuring range
• 1 ppm resolution
• 2 year warranty

User questions & answers

Question:	The photo is for the O2 sensor but the part number is for the CO sensor, which are you selling
Answer:	Hello, We are selling the replacement Carbon Monoxide (CO) sensor (part number: SR-M-MC). We apologize for the confusion. Thank you,

Product description

• Four-gas detector for surveying levels of H2S, oxygen (O2), carbon monoxide (CO), and combustibles in natural and industrial environments, and in other personal safety, training, research, and ambient air monitoring applications
• Electrochemical cell sensor monitors ambient H2S, oxygen , and carbon monoxide levels, and catalytic bead sensor monitors ambient combustible gases continuously
• Audio, visual, and vibration alarms alert simultaneously when ambient H2S, oxygen (O2), carbon monoxide, and combustible gases reach preset low, high, TWA, or STEL levels
• LCD screen shows up to four ambient gas concentrations, battery level, alarm condition, and the status of calibration, bump, and sensor self-tests
• Rechargeable lithium polymer battery reduces the need to replace batteries, and concussion-resistant boot helps protect against damage

User questions & answers

Question:	Please, I would like to buy this device but I want to provide a certificate of origin with the shipment
Answer:	Actually I did find 2 glitches. Tho it does affect your game-play and they both can be resolved easily. On planet Nok you meet Supergirl in the prison and she clumsily flips a switch and lets villains out of their cells. Inside that area, at the bottom of the entrance stairs, if you switch to Atom man, shrink yourself, and run through a small gap on the right side wall (facing-in from the stairs) you will fall through the map. However you just explode and re-spawn back at ground level again.Another glitch happened on the Okaara where you need to use a submersible character and open a temple where you fight a bunch of orange construct guys. You need to beat them all up for the box containing the gold brick to open. I ended up skipping the tour with Daffy Duck at the beginning of the level and attempting to do the gold bricks first. This caused a glitch where all the orange guys did not appear, therefor the gold brick would not unlock. I tried to take the tour after that, and when you reach the first area of orange bad guys, they would not all spawn and I couldn't progress. However, quitting and going back to the planet fresh, doing the tour first, then doing the temple solved the problem. You need to finish the welcome to Okaara tour first.
Question:	Calibration date if I buy the item today
Answer:	100's of characters to choose from tho, and you can swap to them at anytime during freemode.
Question:	Morning! How about the warranty? I'm buying it for Mexico
Answer:	Every lego game has the ability for multiplayers.
Question:	who can i call to ask a question about my order
Answer:	if the game is in Spanish, also in English, but only the whole song is incredible.

Product description

• Four-gas detector for surveying levels of H2S, oxygen (O2), carbon monoxide (CO), and combustibles in natural and industrial environments, and in other personal safety, training, research, and ambient air monitoring applications
• Electrochemical cell sensor measures H2S and carbon monoxide levels in ppm, capillary-pore fuel cell measures oxygen in percent by volume, and catalytic bead combustible sensor measures explosive gases in percent LEL
• Audio, visual, and vibration alarms alert simultaneously when ambient H2S, oxygen, carbon monoxide, and combustible gases reach preset low, high, TWA, or STEL levels
• LCD screen shows up to four ambient gas concentrations, battery level, alarm condition, and the status of calibration, bump, and sensor self-tests
• Integrated diaphragm pump allows for localized sampling of the atmosphere for more precise readings than those generated through diffusion

User questions & answers

Question:	I can detect with this device alcohol gases (Ethanol
Answer:	it detects da smell in the air, different smell
Question:	will this operate while charging
Answer:	Hello, While it is possible to use the unit while it is charging, it is not recommended as it may decrease the life of the battery.
Question:	Does the unit come with calibration certificate
Answer:	i have purchased a couple of these units and they all have come with a calibration certificate.
Question:	Does it come with a hose to read the gases concentration before entering a confined space
Answer:	Hello, This particular monitor configuration includes the following: Detector complete with specified sensor(s), stainless steel alligator clip and concussion-proof housing Rechargeable battery Wall outlet charging adaptor 3 ft. / 1 m calibration hose with quick connect 10 ft. / 3 m sampling hose with particulate filter and quick connect Reversible screwdriver Kit of spare pump filters (5 particulate and 5 hydrophobic) Manual Multi-language CD manual There is another option that is the confined space kit which we also sell on Amazon. You can search this by ASIN #B00ANVEQM4 or Part Number XT-XWHM-Y-NA-CS. This kit includes the following: GasAlertMax XT II Premium Confined Space Kit - includes GasAlertMax XT II detector (% LEL, O2, H2S, CO) and standard package contents, plus wall charging adaptor, IR Connectivity Kit with Fleet Manager II software, sampling probe, hydrophobic (5) and particulate (5) pump filters, 10 ft. / 3 m sampling hose, 34 L calibration gas cylinder (2.5% CH4,18% O2, 25 ppm H2S, 100 ppm CO), 0.5 LPM regulator and carrying case with foam insert. Both are currently available in stock. Let us know if there is anything else we can assist with. Safety Instruments Ltd.

Product description

Smoke detector with optical sensing chamber and microprocessor Drift Compensation algorithms

• Honeywell - 5193SD - Smoke Detector, Photo, Vplex

User questions & answers

Question:	Does this include a camera? The description is vague on what you get - thanks
Answer:	There is no camera, just a smoke detector.
Question:	Is this interchangeable with the 5192SDT model
Answer:	Yes
Question:	Is this a stand alone battery operated unit with a 2-wire dry contact for a hard wired alarm system like the Honeywell Vista 20P
Answer:	This unit utilized SLC (signal line circuit) it is not directly compatible with Vista 20P. It is however compatible with the Ademco Commercial Fire Alarm panels that have SLC ability, like the Vista 32,64, or 128 FBP
Question:	Can you monitor from iPhone
Answer:	Not with our system as built. This detector is installed as part of a complex panel controlled system.