12 best combination sump pump

Product description

The all-new Wayne WSS30VN features an upgraded back up pump with epoxy coated steel and cast iron construction, no more plastic! the 1/2 hp primary pump moves up to 5100 gph at 0 inch of head and the combination 12-volt back up pump moves 2700 gph at 0 inch of head. Assembled in the USA and built to last, the WSS30VN protects your basement with hours of pumping power when the electricity goes out. Battery box dimensions: 9"H X 13"W X 7"L. Check valve required for install, not included in packaging.

• New and upgraded WAYNE WSS30V. Completely pre-assembled and drop in ready.
• Primary pump float switch tested to 1 million cycles, up to 10X more than competitors.*
• Assembled in the US with foreign and domestic parts
• Protection when you need it, back up pump continues running when the power is out. For Use In 16 inch. Diameter or Larger Sump Basins
• Primary pump moves up to 5100 GPH at 0 feet of head.
• 12V DC back up pump moves up to 2900 GPH at 0 feet of head, one of the highest performing DC pumps on the market
• Ultra-Quiet performance; 8 ft. SJTW Power Cord

User questions & answers

Question:	does this pump come with a battery
Answer:	The pump does not come with a battery.
Question:	Can anyone please recommend a battery to purchase for this unit
Answer:	Make sure you get a size 27 deep cycle marine/rv battery, but pay the extra money for an AGM type. I bought the standard one for $81 at Sam’s Club, and it worked fine at first, but it died in 2 years because I did not check and maintain the water levels. After much research I realize that I should have paid the $159 price for the AGM version (maintenance free), and all would be well. I also got into the habit of unplugging the regular pump and dumping a 5 gallon bucket of water down to trigger and exercise the backup system fully.
Question:	What size pvc pipe goes into the single fitting at the top of the unit,and what method are you using to attach it? Thanks
Answer:	I glued a three-foot section of 1-1/2" PVD pipe to the wye-fitting at the top of the pump assemble. At the top of the three-foot section I used an 1-1/2" Fernco rubber coupler with stainless steel clamps to connect it to the drain line. You're going to love this pump. It's the quietest pump I've ever heard.
Question:	Is it ok to connect to the primary pumps PVC before the check valve, eliminating the need for 2 check valves
Answer:	No, you need a check valve for each pump. This happened to my sump pump installation: Over time, the flapper (acts like the valve) in the check valve deformed a little, detached from its hinge point(s), and ended up in the FRONT part of the body. This meant that when water was being pumped out of the sump, the water forced the flapper into the check valve opening... BLOCKING the flow! The check valve ended up working backwards, basically. With the water unable to flow, after enough time, the sump pump burned itself out. If two pumps are feeding through just one check valve, the same thing could happen to both pumps. Each pump needs its own check valve. It's OK for the discharge lines to merge afterwards. BTW: If you really depend of a reliable sump pump installation, spend the extra $30-$50 bucks and get a couple of industrial-strength check valves (regardless if you have a single or double-pump system). They will be "out of sight and out of mind" parts of your installation; you need to KNOW that they'll last!

Product description

WRSC-6 Hz / Volts / Cord: 60 Hz / 115 Volts / 8' Cord Features: -Completely assembled and ready to be installed. -Intermittent Liquid Temp. up to 125 F. -Epoxy coated cast iron housing. -Polycarbonate Cover. -Polypropylene Volute. -Nylon Impeller. -Carbon/Ceramic Shaft Seal. -Upper and lower bearings. -Automatic Operation. -Diaphragm switch Activator. -Switch on - 4-7'' / Switch off - 1-3''. -HP: 1/3. -Hz: 50/60 or 60. -Tank Size: 3. 5 Gallons. -GPM at 5' of Head: 45'. -Maximum Head at 18'. -FNPT Top Vent Port: 2''. -Top Discharge Port: 1. 5''. -Side Discharge Port: 1. 5''.

From the Manufacturer

WRS Series, a convenient smaller sized tank and pump combo, is ideal for impractical gravity drainage areas such as under sinks and laundry trays. Includes: tank and pump with 8-Feet power cord. 1/3 Horsepower, 46 GPM at 5-Feet head, 115 V, 60 Hz.

• Pre-assembled for easy installation
• 3-1/2 Gallon tank size
• Includes two 1-1/2-Inch MNPT x 2-Inch slip adapters for inlet and discharge
• Includes one 2-Inch MNPT x 1-1/2-Inch slip adapter for vent
• Cylindrical polypropylene tank

User questions & answers

Question:	Is this unit quiet? IE can it be heard running when mounted in a cabinet on a rubber pad
Answer:	I have it in a cabinet on a cement floor in my basement. I can hear it run while when it pumps the laundry water. When the dryer is running at the same time it is louder than when the pump runs for the washer.
Question:	Does this pump have to Be connect to the vent pipe
Answer:	most codes require it to be connected since these pumps are almost always located in the basement . most codes will allow the vent be run through the basement wall , not located within 10 feet of a window , you can also use a automatic vent unit , sized 11/2 or 2 inch . pulls air from room pump is located in .
Question:	Can I reduce the 1 1/2" discharge down to 3/4' or 1/2" to run through a pex line? Or will that create too much back pressure for the pump
Answer:	This could restrict the discharge ¾” but that would really restrict your flow. If you call us we can go over the application to make sure that the pump would work in your application. - Franklin Electric/Wastewater/Little Giant: 1-800-701-7894
Question:	Can I reduce this down to 1" and push gray water out to my yard. There is maybe a 2' lift at that most
Answer:	You can reduce it to 1" if needed as long as the run is not longer, because the pump will have to push that much harder.

• Pre-assembled system allowing for easy installation with little or no plumbing knowledge necessary
• ⅓ HP energy efficient permanent split capacitor (PSC) primary pump saves money on your electric bills
• Primary pump capacity 3,100 GPH at a 10 ft. lift and 3,700 GPH at 0 ft. lift
• Backup system capacity 1,000 GPH at 10 ft. lift and 2,000 GPH at 0 ft. lift
• Includes the Basement Watchdog Emergency Battery Backup System with unique monitoring that sounds an alarm, illuminates a warning light and describes what to do for easy maintenance
• Dual float switches on both the primary and backup systems provide 4X the protection
• Provides days of intermittent pumping power on a single battery charge

User questions & answers

Question:	Can this pump be used solely as a backup
Answer:	Yes
Question:	How wide the pit has to be for this
Answer:	The measurements for this system are 8-3/4"L x 10 3/4"W x 17-3/4"H. Its very compact and should fit in most sump basins. For further information please contact our service team at 800-991-0466 option 3.
Question:	can a sealed AGM battery be used with the basement watchdog backup
Answer:	This DFK961 model system will work with a AGM/Maintenance free type battery. I would suggest making sure it has at least 75 Amp hours or higher. Be sure to connect the fluid sensor probe to the + (positive) post on the battery to disable the low fluid alarm. For further information I would suggest calling our service team at 800-991-0466 option 3.
Question:	Does this kit come with the battery housing? I know that you have to purchase the battery & acid separate, but wondering what else I have to buy
Answer:	No, this kit doesn't come with the battery housing (assuming you mean a 'box' to house the battery), but you don't need to buy anything else. For clarity you need this kit, and I can attest to how good and effective it is, well-constructed and very reliable, you then need the battery and the acid. Beware of a few things; the acid is not quite as life and death as it makes out, just take your time. Also the import duty is hefty for both the pump and the battery, but overall well worth the money and peace of mind. Finally don't pick the pump up by the floatation device, it is very tempting, and when you get it you'll see what I mean but you need to use the handle. Hope you enjoy.

Product features

Pre-Assembled for Easy Installation

When you buy a Basement Watchdog Combo (Model DFK961), most of the plumbing has been done for you. The primary AC sump pump and battery backup pump come pre-assembled, including check valves, elbows and pipe already measured and glued, making it fast and hassle-free for you to install the best protection in the industry.

24/7 Monitoring

The controller for your Basement Watchdog Combo (Model DFK961) sump pump system provides crucial, 24-hour-a-day monitoring of pump, power and battery conditions, ensuring your system is ready to protect. The easy-to-understand controller detects irregularities, sounds an alarm, and visually pinpoints problems and solutions on the front panel.

Automatic Protection

With the Basement Watchdog Combo (Model DFK961) on guard, you know your basement is always protected. The control box automatically monitors the system, and should the power go out, the battery backup sump pump will take over to keep your basement dry.

Two Dual Float Switches—Four Times the Protection

The Basement Watchdog Combo (Model DFK961) includes two sets of micro-reed Dual Float Switches. We introduced this technology, proven reliable in other uses for over 50 years, to the pump industry and improved it by including two floats on each pump. Simply stated: if two is good, four is better.

30+ Years Protecting Basements

The Basement Watchdog has been protecting homes for over 30 years and continues to lead the pack. We build the most dependable, user-friendly pumps in the industry using intelligent design, premium components, and quality manufacturing practices that include thoroughly testing every single unit.

Pumping Power

The Basement Watchdog Combo (Model DFK961), our most economical option, moves 3,720 GPH at 0' height (3,100 GPH at 10' height) from the primary AC sump pump, and 2,000 GPH at 0' height (1,000 GPH at 10' height) from the battery backup sump pump. Plus, both the primary and backup can run simultaneously, providing extra capacity if needed.

Automatic Charging

The Basement Watchdog Combo (Model DFK961) is equipped with an automatic charger that helps extend the life of the battery while maintaining the maximum charge on the battery without overcharging. Plus, it’s compatible with our wet cell and maintenance-free batteries.

Matching Batteries

The Basement Watchdog Combo (Model DFK961) is equipped with an automatic charger that helps extend the life of the battery while maintaining the maximum charge on the battery without overcharging. Plus, it’s compatible with our wet cell and maintenance-free batteries.

Product description

The new PHCC Pro Series, "Pair of Pumps" combination systems, couples an energy efficient primary sump pump and battery backup sump pump into one compact system. The primary pump operates off AC power. If the power is interrupted, or more water is coming into the sump than the AC pump can handle, the backup sump pump will begin pumping automatically. The units come pre-assembled for easy installation and include four float switches for ultimate protection. Two floats with the primary pump, and two floats with the backup. The combination systems also contain unique monitoring features that warns the homeowner if the power goes out, battery fluid is low, backup pump was activated, or if the battery is discharged, defective, or battery terminals need cleaning. In addition the PS-C33 pump controller can send an alarm signal to a home security system or auto dialer. 1/3 HP - PSC motor Included with system: Primary pump. Backup pump. Backup system controller/charger with fluid sensor. Primary pump controller (DFC1) with caged dual float switch. 1-1/2 rubber union. Assembly includes two check valves and hardware. Sump Foot - raised platform for both pumps. Battery box. Battery fill bottle (battery not included)

• 3000 GPH flow at 10-Feet head with 31-Feet max head. Back-up 2400 GPH
• Automatically switches to battery power when AC fails
• Backup pump will assist primary pump if excessive amounts of water are entering the sump
• Detects irregularities, sounds an alarm, and pinpoints problems and solutions on control panel or to an auto dialer
• Primary 115 Volts, 60Hz. Back-up 9.0 Amps DC current

User questions & answers

Question:	Does this require an internet connection for tests
Answer:	No internet connection is required. The PHCC 2400 controller will run the pump about once a week. The pump failure light will come on if for whatever reason the pump does not work properly. For more information please contact our service team at 800-991-0466 option 3.
Question:	Will this work in an 18" diameter sump pit
Answer:	Yes, easily. The dimensions are 10"W x 11"D x 23.7" high.
Question:	If the primary pump can not handle the amount of water coming into the pit will the secondary start up
Answer:	Yes ! This is one of the few units on the market that does operate that way. Even though the discharge is 11/2" you should pipe the discharge out in 2" to take advantage of this feature.
Question:	Can i use marine (deep cycle) 24 series battery with it? and do i set it for non-maintenance free then
Answer:	Yes you can use those batteries. You set it for maintenance free with any batteries that you don't add acid to.

Product description

The Basement Watchdog Big Combo is a pre-assembled, energy-efficient 1/2 HP primary sump pump combined with the number one selling Basement Watchdog Special CONNECT Battery Backup Sump Pump System. It’s the D.I.Y. solution for replacing your current sump pump with an efficient, cost-saving one that includes a redundant battery backup system with 24 hour a day monitoring and a Wifi capable controller. With two sump pumps in your sump pit, continuous monitoring and remote notification allowing you to receive texts, emails and in App alerts you can feel safe that your basement is protected. The system is easy to install with little or no plumbing knowledge required. The ½ HP Cast Iron primary pump provides outstanding capacity—pumping up to 4,400 GPH at 0 ft. lift. The backup sump pump is battery-operated, and pumps at 2,600 GPH at 0 ft. lift. The backup sump pump can run intermittently for days on a single battery charge from either the Basement Watchdog Maintenance-free AGM battery (BW27AGM) or the flooded lead-acid battery (30HDC140S). The WiFi capable controller monitors the pump, power, and battery conditions 24 hour a day. Plus, the controller exercises the pump weekly to make sure it stays healthy. A remote terminal provides easy connection to a security system, auto dialer or other dry contact device. The backup controller also includes a USB port that connects to the Basement Watchdog CONNECT WiFi module, allowing you to receive texts, emails and in App alerts for the ultimate peace of mind when you’re away from home. You can feel safe that The Basement Watchdog is WATCHING OUT FOR YOU!

• 1/2 HP energy efficient permanent split capacitor (PSC) primary pump can save money on your electric bills
• Primary pump capacity 3,540 GPH at a 10 Ft. lift and 4,400 GPH at 0 Ft. lift. Backup system capacity 1,850 GPH at 10 Ft. lift and 2,600 GPH at 0 Ft. lift
• Includes a WiFi capable battery backup system that provides 24 hours a day monitoring of pump, power and battery conditions, backup controller will sound an alarm, illuminates a warning light and describe what to do for easy maintenance
• Allows for connection to a Basement Watchdog CONNECT Module (BW-WiFi or BW-HZM), giving you real time alerts via text, email, or through the Basement Watchdog App
• Provides days of intermittent pumping power on a single battery charge and is compatible with both wet cell and maintenance-free AGM batteries. Connect two batteries in parallel for double the run time

User questions & answers

Question:	Is the back up pump submerged under normal operation
Answer:	Yes, both the primary and backup pumps on this system are completely submersible. For more information please contact our service team at 800-991-0466.
Question:	What is the min size basin this fits into? I have a 12 by 12 by 24 in deep basin will it fit
Answer:	The dimensions on this product are 8.75 x 11.75 x 18 inches so if your basin is 12" wide it should be able to fit. For further information I would recommend calling our service team at 800-991-0466 option 3,
Question:	can you use any 12 volt battery for back up
Answer:	You would need to use a 12v Deep cycle standby battery with this system in order to run the backup pump. The battery can be either a maintenance or maintenance free one and look for an amp hour rating of around 75 or higher. For more information feel free to contact our service team at 800-991-0466 option 3.
Question:	If i have one of the connect modules, and the power goes off to my router, what notification do i receive
Answer:	You would receive a message stating that the connection has been lost. This can be setup to send messages through email, text, and the Wi-fi app on your phone.

Product features

Pre-Assembled for Easy Installation

When you buy a Basement Watchdog Combo (Model CITE-33), most of the plumbing has been done for you. The primary AC sump pump and battery backup pump come pre-assembled, including check valves, elbows and pipe already measured and glued, making it fast and hassle-free for you to install the best protection in the industry.

24/7 Monitoring

The controller for your Basement Watchdog Combo (Model CITE-33) sump pump system provides crucial, 24-hour-a-day monitoring of pump, power and battery conditions, ensuring your system is ready to protect. The easy-to-understand controller detects irregularities, sounds an alarm, and visually pinpoints problems and solutions on the front panel.

Automatic Protection

With the Basement Watchdog Combo (Model CITE-33) on guard, you know your basement is always protected. The control box automatically monitors the system, and should the power go out, the battery backup sump pump will take over to keep your basement dry.

Two Dual Float Switches—Four Times the Protection

The Basement Watchdog Combo (Model CITE-33) includes two sets of micro-reed Dual Float Switches. We introduced this technology, proven reliable in other uses for over 50 years, to the pump industry and improved it by including two floats on each pump. Simply stated: if two is good, four is better.

30+ Years Protecting Basements

The Basement Watchdog has been protecting homes for over 30 years and continues to lead the pack. We build the most dependable, user-friendly pumps in the industry using intelligent design, premium components, and quality manufacturing practices that include thoroughly testing every single unit.

Pumping Power

The Basement Watchdog Combo (Model CITE-33), our most economical option, moves 3,720 GPH at 0' height (3,100 GPH at 10' height) from the primary AC sump pump, and 2,000 GPH at 0' height (1,000 GPH at 10' height) from the battery backup sump pump. Plus, both the primary and backup can run simultaneously, providing extra capacity if needed.

Automatic Charging

The Basement Watchdog Combo (Model CITE-33) is equipped with an automatic charger that helps extend the life of the battery while maintaining the maximum charge on the battery without overcharging. Plus, it’s compatible with our wet cell and maintenance-free batteries.

Matching Batteries

The Basement Watchdog Combo (Model CITE-33) is designed to be used in conjunction with any of our batteries: The Maintenance Free Standby Battery (Model BW-27AGM), the Big (wet cell) Standby Battery (Model 30HDC140S), or the Emergency (wet cell) Standby Battery (Model 24EP6).

Product description

Designed using Moeller's time-tested components giving you the needed performance and reliability. CONTROL BOX: Includes battery burn-out and overcharge protection. The self-contained, 10 amp battery recharger system is a solid-state, automatic controller with alarms, light indicators and warning systems. LCD SCREEN: Always displays battery voltage along with other helpful information about the system. AUXILIARY ALARM CONTACT: A set of dry contacts allows system to connect to home security alarm, auto dialers, etc. SWITCH: Reliable, low voltage vertical float switch. FITTINGS: An integrated DC pump discharge check valve, additional AC pump check valve, tee and adapter are included. TECHNOLOGY: This charger uses the latest switch mode technology available. This allows for an extremely efficient charger in a compact design. It satisfies the rigid California Battery Council standards. Charger is also crus approved. BATTERY CASE: The included battery case will accommodate maximum battery dimensions of 13" L x 71/2" W x 91/2" H (33 cm L x 19 cm W x 24 cm H) and fits all group size 27, 29 and 31 batteries. Made from non-corrodible polyethylene (NOTE: 12 volt battery NOT included). NOT a Bilge pump. Designed, Engineered and Assembled by Moeller as a sump pump.

From the Manufacturer

Designed using Zoeller's time-tested components giving you the needed performance and reliability. CONTROL BOX: Includes battery burn-out and overcharge protection. The self-contained, 10 amp battery recharger system is a solid-state, automatic controller with alarms, light indicators and warning systems. LCD SCREEN: Always displays battery voltage along with other helpful information about the system. AUXILIARY ALARM CONTACT: A set of dry contacts allows system to connect to home security alarm, auto dialers, etc. SWITCH: Reliable, low voltage vertical float switch. FITTINGS: An integrated DC pump discharge check valve, additional AC pump check valve, tee, and adapter are included. TECHNOLOGY: This charger uses the latest switch mode technology available. This allows for an extremely efficient charger in a compact design. It satisfies the rigid California Battery Council standards. Charger is also cURus approved. BATTERY CASE: The included battery case will accommodate maximum battery dimensions of 13" L x 71/2" W x 91/2" H (33 cm L x 19 cm W x 24 cm H) and fits all group size 27, 29 and 31 batteries. Made from non-corrodible polyethylene (NOTE: 12 volt battery NOT included). NOT a Bilge pump. Designed, Engineered and Assembled by Zoeller as a sump pump.

• Includes: Model 53 115-volt pump, Model 508 Aqua not, 115 Volt DC backup system with pump, check valve, float switch and piping
• Plumbed in 1-1/2" Such 40 PVC pipe
• Comes fully assembled and ready to install in your clear water sump
• Extra protection when the primary AC pump fails due to power outages
• Fully solid state automatic 10A charger/controller with alarm, light indicator and warning system

User questions & answers

Question:	Will the zoeller 508-0006 unit fit in a 12 inch diameter pit
Answer:	At it's widest point, the assembly measures 10" according to the drawings on the Zoeller site.
Question:	My sump pit is 14 1/2 inches in diameter. Will this fit
Answer:	It will not fit because the unit is a little over 15" with both pumps put on, so you will need at least a 16" crock for the float to move freely inside. We have a 14 1/2 inch crock and bought this because the answers stated that it would fit, when it, in fact, does not. The unit itself is very nicely made - no plastic pieces on it, it's made of cast iron. Just wanted people to be aware of the measurements.
Question:	With the Zoeller will the check valve bang like my current system does when it shuts off
Answer:	The one I installed doesn't slam or bang. If your standing over it when it runs you can when it shuts off but it not noisy.
Question:	Pumps
Answer:	Yes, 2 pumps- a main one and then the back up. Back up gets triggered with a higher float and runs off the battery back up. If power fails, the back up pump takes over

Product description

Most homeowners discover that their sump pump has a problem when the basement is already flooded. PumpSpy's sump pump smart outlet contacts homeowners that their sump pump has a problem before flooding can occur. The sump pump smart outlet connects to the free PumpSpy monitoring service that constantly watches your sump pump automatically, 24/7. The PumpSpy sump pump smart outlet works with any 120v sump pump. Simply connect the smart outlet to your Wi-Fi network and plug in your sump pump! PumpSpy's computers will automatically track incoming data from your sump pump and check that the pump is working properly. If any issues are detected, PumpSpy automatically sends out text messages, emails and app alerts. Download the free PumpSpy app to receive reports, alerts and check your sump pump anytime, anywhere! the PumpSpy sump pump smart outlet includes: smart outlet, screw, high water sensor, mounting bracket and installation guide. Wi-Fi network required. Protect your basement from flooding with the PumpSpy sump pump smart outlet.

• Makes your sump pump a Wi-Fi connected smart pump
• Free monitoring included, connects your sump pump to PumpSpy's 24/7 monitoring service
• PumpSpy sends text messages, emails and app alerts to your smart phone, tablet and computer if your sump pump has a problem
• Apple and android PumpSpy apps available for free download
• Includes high water sensor & alerts, no additional equipment required

User questions & answers

Question:	Can you enter multiple email accounts and mobil phone numbers
Answer:	Yes you can enter multiple phone numbers and email addresses.
Question:	Can multiple pump spies be installed on a multi pump system
Answer:	Yes. You can have as many Smart Outlets as you have sump pumps. You can give each Smart Outlet a nickname (furnace room, main pump, etc.) to tell them apart in the PumpSpy app.
Question:	what is the cost of the monitoring service
Answer:	Zero. "Free Monitoring Included"
Question:	What happenes if the main power goes out how does this send alerts
Answer:	Here is what would happen in 2 similar scenarios: If the power goes out and your WiFi network is still active (UPS backup on router OR the power is only partially out, tripped breaker), the Smart Outlet stores enough power on the board to send data for several seconds. In this scenario, you would receive an AC power failure alert. If the power is completely out, the Smart Outlet would try to send the AC power failure alert, but your internet connection would be down. In this scenario, you would receive an alert that your Smart Outlet has lost communication with the PumpSpy Monitoring Service. If your Smart Outlet doesn't "check in" for over 2 minutes, this alert will be sent. The outlet does not communicate directly with the homeowner, the Smart Outlet sends all data and communications to PumpSpy's Remote Monitoring computers, which process incoming data and send alerts as required. Hope that answers your question!

Product features

The Problem

A sump pump is typically among the least of a homeowner’s worries until it starts raining. Hard.

Then the questions begin:

• Is my sump pump working?
• How would I know if there’s a problem?
• Is my basement flooding?

For many homeowners, they find out their sump pump has a problem when it’s too late. The basement is flooded and has left behind a home in need of repair, a huge cleanup project and potentially thousands of dollars in damaged or ruined property.

The PumpSpy Solution

PumpSpy uses patented, proprietary technology to remotely monitor your sump pump 24 hours a day, 7 days a week. Simply download the PumpSpy app, connect the Smart Outlet to your Wi-Fi network and plug in your sump pump. PumpSpy's computers will automatically track incoming data from your pump and check that the pump is working properly. When any issues are detected, PumpSpy sends you detailed alerts immediately via push notifications, text message or email.

You can check your real time pump status from anywhere using the PumpSpy app, available for iOS and Android.

PumpSpy PSO1000 WiFi Sump Pump Smart Outlet

The PumpSpy WiFi Sump Pump Smart Outlet works with your existing sump pump and home Wi-Fi network.

PumpSpy 24/7 Remote Monitoring

PumpSpy’s servers constantly watch your sump pump automatically. PumpSpy detects problems and sends alerts as soon as an issue is detected!

Instant Notifications and Alerts

When a problem happens, PumpSpy sends you instant alerts via the free PumpSpy App.

Instant Alerts On Your Smart Phone

PumpSpy sends instant alerts to your phones and other devices when an issue is detected:

• Main Pump Failure
• Main Pump Running Excessively
• Blocked or Frozen Discharge Line
• Power Outage
• High Water Level
• Internet Connection Lost
• and many more!

Check On Your Pump Anytime

Check the real time status of your sump pump anytime with the PumpSpy app:

• Internet Connection Status
• WiFi Signal Strength
• AC Power Status
• Sump Pump Status
• Water Level Status

Real Time Pump Cycle Information

See detailed information on your sump pump operation:

• Pump Cycles Today
• Last Cycle Time
• Estimated Gallons Pumped
• Total Pump Cycles by Date
• All Pump Cycles by Date with Timestamps

Product description

This Red Lion Sump Pump is ideal for average-to-high volume water removal in residential spaces such as basements, laundry facilities, and crawl spaces. This system offers worry-free operation; providing you with a back-up pump, and double the flow rate when needed. Dual automatic submersible sump pumps with pre-assembled piping and check valves included. Maximum head of 25 feet. Comes with PSC motors, 10-foot power cord and 1-1/2-inch FNPT discharges, piggyback float switch and has a clog-resistant design (1/2" solids handling). Single pump gallons per hour at height: 0' - 3,350, 5' - 3,000, 10' - 2,460, 15' - 1,860 and 20' - 960. Dual pump gallons per hour at height: 0' - 6,000, 5' - 5,400, 10' - 4,425, 15' - 3,345 and 20' - 1,725. If, after 30 days, you are having a problem with your Little Giant, Franklin, or Red Lion product, call the Franklin Electric Tech Support Team at 888-956-0000 for Troubleshooting and Warranty Instructions. The Tech Support Team is available M-F from 7:00am-4:30pm CST.

• Dual automatic submersible sump pumps
• Pre-assembled piping and check valves included
• Maximum head of 25',010' power cord
• 1-1/2 inch FNPT discharges, piggyback float switches
• Clog-resistant design (1/2" semi-solids handling), PSC motors, not suitable for pond use

User questions & answers

Question:	What battery is required
Answer:	No battery. Two electric plugs.
Question:	Why do the instructions call for removing one float when installing
Answer:	Both floats are ob mine. One is just wet higher than the other.
Question:	Does each pump have its own power cord, so they can be used on separate circuits in case primary pump failure causes breaker to trip
Answer:	Yes each pump has it’s own power cord. I am going to do the same thing, where each is on its own circuit.
Question:	Does the backup go on if the primary fails or is it on all the time with the primary
Answer:	https://www.sumppumpsdirect.com/Red-Lion-RL-SC33DUP-Sump-Pump/p13845.html 2nd pump as needed.

Product description

Raybend's Primary Sump Pump Backup Power Supply is an ideal solution for homeowners worried about keeping their basements dry during a power outage. Engineered to reliably handle either one Primary Sump Pump (12.5 Amps MAX) or two Primary Sumps simultaneously (6.25 Amps MAX each) with a pure sine wave output that is designed to simulate the characteristics of typical Utility Company generated 120 VAC home power. This system automatically switches from 12 VDC to 120 VAC when AC Power goes out and automatically reverts back when AC Power is restored. Charges and maintains the battery (Not Included) with a powerful 10 Amp built in Charger to quickly recover form any extensive outage.

• Automatically switches over to Battery Power when AC power goes out. (Battery Not Included. A Deep Cycle AGM Battery is Recommended)
• Generates a Pure Sine Wave 120 VAC voltage to reliably power your primary sump pump
• Automatically recharges a Battery When AC Power is restored with a powerful 10 Amp Built-in charger
• 1500 Watt Output is enough to power two Primary Sump Pumps simultaneously (6.25 Amps Max each)
• Can be used as a power inverter for many applications requiring backup power

User questions & answers

Question:	Would this unit work with a 12v 100ah deep cycle lifepo4 3000+ life cycles rechargeable lithium battery
Answer:	Yes. That battery will work perfectly with this system.
Question:	have a question re. the charging light - it does not turn on at all even if the charging switch is on after installation. Is this a defect
Answer:	The red light should be on if the battery is charging. The green light then goes on when the battery is charged. If the red light never goes on there is something wrong.
Question:	Does the charger require an external battery management system for lead acid batteries to handle over charge
Answer:	No it doesn't. It is automatic as long as you use a marine battery, deep cycle.
Question:	How long should the inverter take to charge the battery
Answer:	When I plugged the battery into the inverter it took about 6 hours too charge then the 2 green lights displayed which means inverter is charged. The green lights stay on

Product features

One Primary Sump Pump

Efficiently powers one sump pump with a maximum draw of 12.5 Amps.

Two Primary Sump Pumps

Provides ample power for two sump pumps with maximum draws of 6.25 Amps each.

Other Backup Power Applications

Securely functions as a power inverter for applications that require backup power

Powerful 10 Amp Charger

Quickly charges your battery when AC power is available.

Two Grounded Outlets

Safely power two primary sump pumps with maximum draws of 6.25 Amps each.

Automatic Power Detection

Automatically detects when a power failure occurs and provides AC power to connected sump pumps.

Easy Installation

Easily become prepared for power outages with hassle-free installation.

Product description

BWE Features: -Includes: Controller, charger, dual micro reed float switch, pump, sensor to monitor battery fluid levels and battery box (battery sold separately). -Pump system. -Fits next to the main AC pump and automatically begins pumping during a power outage, when the main pump fails or when water flow exceeds the capacity of the main pump. -Unique monitoring system sounds an alarm when maintenance is needed or a problem arises. -Light on the display panel will indicate the cause of the alarm and the corrective action. -Pumps up to 6 hours continuously. Finish: -Yellow. Hardware Finish: -Stainless Steel. Material: -Plastic. Hardware Material: -Stainless steel. Number of Items Included: -9. Corrosion Resistant: -Yes. Frequency: -60 Hertz. Generic Specifications: -Power supply requirements: 115 Volts AC. Dimensions: Overall Height - Top to Bottom: -6. 5". Overall Width - Side to Side: -8. 5". Overall Depth - Front to Back: -4. 5". Overall Product Weight: -3. 5 lbs.

From the Manufacturer

The Basement Watchdog Emergency Battery Backup Sump Pump pumps 2,000 GPH at 0 ft. of lift or 1,000 GPH at 10 ft. of lift. This convenient pump fits next to the main AC pump and automatically begins pumping during power outages, when the main pump fails or when water flow exceeds the capacity of the main pump. Its unique monitoring system sounds an alarm when maintenance is needed or a problem arises. A display panel indicator light will identify the cause of the alarm and the proper corrective action. Battery not included. See 30HDC140S for the battery.

• Pumps 2,000 GPH at 0 ft. lift and 1,000 GPH at 10 ft. lift
• User-friendly controller monitors battery, pump and power conditions 24 hours a day
• Provides days of intermittent pumping power on a single battery charge
• Compatible with both wet cell and maintenance-free AGM batteries

User questions & answers

Question:	I got this hooked up and activated the float to test. The pump activated, but when I lowered the float it kept running. Is the controller defective
Answer:	When the float switch for the backup pump is activated, he pump will run on a timer which is usually around 25-30 seconds. I would recommend testing it again and give it at least a minute to shut off. For further information contact our service team at 800-991-0466 option 3.
Question:	Can this run semi-continuous while connected to AC power when main pump fails? Wayne controller had burning smell while charging and running
Answer:	The unit has its' own floats, so the pump will run when the water level raises the float, so it depends on where you place the backup pump float. Place it above the main unit float so if the water level continues to rise due to a failed main pump, the backup pump will kick-in.
Question:	If my main pump fails will the back up kick in
Answer:	That will only happen if you have the battery back-up unit in Working order. It is designed to kick in when the power fails or if the power has been out and the float switch on the main unit is activated and then the battery unit takes over. You need to consult the owner's manual for the exact info.
Question:	battery run time
Answer:	It really would depend on the type of battery ,marine battery deep cycle works best. and the amount of water entering your basement . From a few hours to all day

Product features

24/7 Monitoring

The controller for the Basement Watchdog Emergency (Model BWE) provides crucial, 24-hour-a-day monitoring of pump, power and battery conditions, ensuring your sump pump is ready to protect. The easy-to-understand controller detects irregularities, sounds an alarm, and visually pinpoints problems and solutions on the front panel.

Automatic Protection

With the Basement Watchdog Emergency (Model BWE) battery backup sump pump on guard, you’ll have confidence knowing your basement is protected. The control box automatically monitors the system, and should the power go out or the main sump pump fail, the battery backup sump pump will take over to keep your basement dry.

Dual Float Switches—Twice the Protection

The Basement Watchdog Emergency (Model BWE) battery backup sump pump includes a micro-reed Dual Float Switch. We introduced this technology, proven reliable in other uses for over 50 years, to the pump industry and improved it by including two floats. Simply stated: if one is good, two is better.

30+ Years Protecting Basements

The Basement Watchdog has been protecting homes for over 30 years and continues to lead the pack. We build the most dependable, user-friendly pumps in the industry using intelligent design, premium components, and quality manufacturing practices that include thoroughly testing every single unit.

Pumping Power

The Basement Watchdog Emergency (Model BWE) battery backup sump pump, our most economical backup, moves 2,000 GPH at 0' height (1,000 GPH at 10' height).

Automatic Charging

The Basement Watchdog Emergency (Model BWE) battery backup sump pump is equipped with an automatic charger that helps extend the life of the battery while maintaining the maximum charge on the battery without overcharging. Plus, it’s compatible with our maintenance-free and wet-cell batteries.

Matching Batteries

The Basement Watchdog Emergency (Model BWE) battery backup sump pump is designed to be used in conjunction with our maintenance-free AGM battery (Model BW-27AGM), or wet-cell batteries (Models 30HDC140S and 24EP6).

Product description

The Wayne CDU980E submersible sump pump can move up to 5490 gallons per hour (gph). The top suction design filters debris and minimizes clogging. It is a rugged, stainless steel and cast iron submersible sump pump. This pump is designed for 11-Inch diameter and larger sump pits. Intended for indoor use only.

From the Manufacturer

The Wayne CDU980E submersible sump pump can move up to 4600 gallons per hour (gph). The top suction design filters debris and minimizes clogging. It is a rugged, stainless steel and cast iron submersible sump pump. This pump is designed for 11-Inch diameter and larger sump pits.Intended for indoor use only.

• Assembled in the US with foreign and domestic parts
• Top suction pump design minimizes air locks and clogging from debris in bottom of sump pit.Assembled in us, with foreign and domestic components
• Stainless steel motor housing and rugged, cast iron pump base
• Vertical float switch, tested to 1 million cycles!4600 GPH at 10 ft. of discharge lift
• 1-1/2 In. NPT Discharge for compliance with building codes

User questions & answers

Question:	Can this pump be hooked up to a battery backup
Answer:	It pulls too much current for most battery backups, a generator will run it fine.
Question:	how long is the power cord
Answer:	Just received my Wayne CDU980E. I, too, was concerned with this question. Power cord measures about 90-inches (7.5-feet) from where it connects to the top of the sump motor (which is about 11-inches above the bottom of the pump). I can't find this marked on Wayne's literature for the CDU980E.
Question:	When the pump is switched on by the floater, how long does it run
Answer:	If there is merely water in the sump pit, you don't need this powerful a pump. This 3/4 HP pump is for handling major water flowing into the pit. When that happens in our cellar, the pump runs until it out-runs the flow of incoming water.-- sometimes for minutes sometimes for hours. We have 4 sump installations in 4 buildings. When the water table (level of the ground water in the outside ground) is high, three of these systems pump a lot of the time and pretty constantly. We have 2 pumps in each pit so if one fails we do not get flooded. Each Pump (if more than one in the system) needs to have a check valve/ back-flow preventer so it will force the other pumps to actually pump the water up and out and not allow an operating pump to to just pump back out through the other , (not then pumping) pump. The should also be placed at different levels so they don't necessariy go on at the same time, thus reserving one as a kind of back up. Of course, if there is really a lot of incoming water -- which we had when we first bought our house, it takes both pumps to handle the in flow and avoid flooding. NOw that we use the large diameter PVC piping, it works so much better that a single pump pof this size would probably be fine. It is best to pipe the pumps with real PVC pipe and in 1 1/2" or 2" size. This will increase the flow rate by around twice as much flow as the skinny (1 1/4") highresistance black curly-sided plastic pipe they often come with. Good luck and stay dry.
Question:	when you say 'top suction' does this mean the pu,p must be totally submerged
Answer:	The pump draws water from the "LOWER" part of the pump a few inches off the floor. It does not have to be completely submerged to draw water. When the bulb float rises enough to turn on the float switch it sucks water. It turns on before the water reaches the top of the pump. I use this one and I know. Hope this helps someone.

Product description

Ideal for average to high-volume water and effluent removal in residential spaces such as basements, laundry facilities, and crawl spaces.

From the Manufacturer

This sump pump is ideal for high-volume water removal. It features heavy-duty cast iron construction, energy efficient motor. Extremely versatile, with tethered float switch.

• Automatic submersible sump pumps
• 1-1/2'' FNPT discharge
• Piggyback float switch
• Clog-resistant design (1/2" semi-solids handling)
• Psc motor,010' cord, not suitable for pond use

User questions & answers

Question:	Can i remove the float switch completely and use a different piggyback switch
Answer:	This mini submersible pump is designed for small to medium size aquarium, tabletop fountains, water gardens and hydroponic systems. Water pump LED lights provide amazing night lighting and are waterproof. Great for decorating your indoor fountain, pool, pet fountain, garden, pond, fish tank, aquarium, hydroponic systems. decorating indoor fountains, swimming pools, pet fountains, ponds, fish tanks, aquarium pump, hydroponic, statues
Question:	Would this fit in a sump that is only 14.5" in diameter
Answer:	It is quiet, I don't recall hearing the pump.
Question:	how long is the power cord
Answer:	no..can;'t see anyway to do that..I wanted to do the same thing
Question:	What is the watts rating
Answer:	Yes

Product features

Red Lion

Backed by the heritage of a global leader in the development and manufacturing of systems and components that move water, the Red Lion brand remains at the forefront of product innovation by listening to its customers, adapting to the market, and continuing to invest in research and development. This innovative product portfolio is supported by unparalleled service to provide you with current solutions to your water pumping challenges.