8 best lowes sump pumps

Product description

The Wayne CDU980E submersible sump pump can move up to 5490 gallons per hour (gph). The top suction design filters debris and minimizes clogging. It is a rugged, stainless steel and cast iron submersible sump pump. This pump is designed for 11-Inch diameter and larger sump pits. Intended for indoor use only.

From the Manufacturer

The Wayne CDU980E submersible sump pump can move up to 4600 gallons per hour (gph). The top suction design filters debris and minimizes clogging. It is a rugged, stainless steel and cast iron submersible sump pump. This pump is designed for 11-Inch diameter and larger sump pits.Intended for indoor use only.

• Assembled in the US with foreign and domestic parts
• Top suction pump design minimizes air locks and clogging from debris in bottom of sump pit.Assembled in us, with foreign and domestic components
• Stainless steel motor housing and rugged, cast iron pump base
• Vertical float switch, tested to 1 million cycles!4600 GPH at 10 ft. of discharge lift
• 1-1/2 In. NPT Discharge for compliance with building codes

User questions & answers

Question:	Can this pump be hooked up to a battery backup
Answer:	It pulls too much current for most battery backups, a generator will run it fine.
Question:	how long is the power cord
Answer:	Just received my Wayne CDU980E. I, too, was concerned with this question. Power cord measures about 90-inches (7.5-feet) from where it connects to the top of the sump motor (which is about 11-inches above the bottom of the pump). I can't find this marked on Wayne's literature for the CDU980E.
Question:	When the pump is switched on by the floater, how long does it run
Answer:	If there is merely water in the sump pit, you don't need this powerful a pump. This 3/4 HP pump is for handling major water flowing into the pit. When that happens in our cellar, the pump runs until it out-runs the flow of incoming water.-- sometimes for minutes sometimes for hours. We have 4 sump installations in 4 buildings. When the water table (level of the ground water in the outside ground) is high, three of these systems pump a lot of the time and pretty constantly. We have 2 pumps in each pit so if one fails we do not get flooded. Each Pump (if more than one in the system) needs to have a check valve/ back-flow preventer so it will force the other pumps to actually pump the water up and out and not allow an operating pump to to just pump back out through the other , (not then pumping) pump. The should also be placed at different levels so they don't necessariy go on at the same time, thus reserving one as a kind of back up. Of course, if there is really a lot of incoming water -- which we had when we first bought our house, it takes both pumps to handle the in flow and avoid flooding. NOw that we use the large diameter PVC piping, it works so much better that a single pump pof this size would probably be fine. It is best to pipe the pumps with real PVC pipe and in 1 1/2" or 2" size. This will increase the flow rate by around twice as much flow as the skinny (1 1/4") highresistance black curly-sided plastic pipe they often come with. Good luck and stay dry.
Question:	when you say 'top suction' does this mean the pu,p must be totally submerged
Answer:	The pump draws water from the "LOWER" part of the pump a few inches off the floor. It does not have to be completely submerged to draw water. When the bulb float rises enough to turn on the float switch it sucks water. It turns on before the water reaches the top of the pump. I use this one and I know. Hope this helps someone.

Product description

Before you click to continue, you should know this isn’t just a gift card. It’s carte blanche for someone to pursue the dreams they have for their home. A wallet-sized dose of inspiration that grants them permission to improve and enhance. Just thought you should know. Now click away.

• Use at any Lowe's location or redeem online at Lowes.com.
• Redemption: Instore and Online
• It's the perfect gift for any occasion.
• No returns and no refunds on gift cards.

User questions & answers

Question:	Do you have more price options for gift cards? I wanted to gift
Answer:	visa
Question:	What kind of packaging is this sent
Answer:	Large yellow envelope with bubble wrap. 3x's bigger than the gift card itself
Question:	if i go to lowes can i buy another gift card like visa with my lowes gift card
Answer:	NO, NO , NO! It says so right on the back of the card.
Question:	Can a friend use this card at Lowes to pay on his Lowes credit account
Answer:	No, you can only pay for purchases with gift card.

Product description

Quietly and quickly drain your pool or pond in a matter of hours with the EZ Travel Submersible Drain Pump. This pump is perfect for emptying water tanks, ponds, pools, hot tubs, low lying flooded areas, and more. The impact-resistant plastic body is rust-resistant and built to last. This drain kit includes an exploded parts diagram and instructions. Unlike other drain pumps on the market; this model is rated at horse power and can drain a hot tub in minutes. The pump requires little work to operate and is completely submersible. An overheat prevention mechanism automatically shuts the pump off when the water line becomes too low. Sit back and let this EZ Travel Submersible Drain Pump do the work to drain your pool or pond in just a few hours!

• UP TO 2,000 GPH - This new automatic submersible drain pump from EZ Travel Collection is capable of pumping up to 2,000 gallons of dirty water an hour. Complete with a drain hose, hose clamp, and automatic float switch shutoff feature, this pump takes the hard work out of pool maintenance.
• 400 WATT MOTOR - Rated at horsepower, this transfer pump drains a hot tub in minutes. The pump requires little work to operate and is completely submersible. The removable and adjustable spigot makes pump maintenance simple.
• COMPLETELY SUBMERSIBLE - Easy to operate, this automatic sump pump is completely submersible. The overheat prevention mechanism automatically shuts it off when the water line becomes too low to feed the pump.
• PORTABLE AND RELIABLE - This EZ Travel Collection submersible drain pump combines portability, reliability, and power. With strong impact-resistant casting, our new streamlined design includes a durable and convenient carry handle.
• DIMENSIONS - Pump: 12.5" x 6" x 6" (L x W x H). Drain Hose Length: 25' Drain Hose Diameter: 1-1/2"

User questions & answers

Question:	Safe to use with Salt water pool
Answer:	Yes, safe for use with salt water pools. Thank you!
Question:	i want to pump water out of may crawl space will it work
Answer:	This pump is designed to be submerged into deep water. It works great for draining hot tubs, pools, ponds, but just as long as the water is at least 1-2 feet to start. The pump will leave about 2-3 inches of water at the bottom of said hot tub or pond. So as long as your crawl space has deep water (like 1-2 feet) then yes, otherwise if the water level is low to begin with; I would try a pump like this: https://www.amazon.com/dp/B07PH2Z2Y3?ref=myi_title_dp
Question:	Have a stream in back of home. Looking for emergency pump to send excess water down driveway slope if we ever got excess rain. Would this work
Answer:	As long as the pump is under water; it will work just fine. This means you would have to place this pump in a place where your stream is at least 2 feet deep before plugging it in and running the hose over to your driveway.
Question:	Does it come with everything you need to start using it
Answer:	Yes, you just set it upright in the bottom of your spa and unroll the hose then plug it in and it starts pumping water out automatically. Nothing else needed to buy. Works great and drains my 350 gallon spa in about 20 minutes.

Product description

Superior Pump builds pumps that are truly Built to Last and are 100 percent factory tested. Superior Pump pedestal pumps use quality components including solid copper motor windings, electronically controlled split capacitors, heavy duty drive shafts, stainless steel impellers and 10 foot power cords. Superior Pump model 92333, 1/3 HP thermoplastic pedestal sump pump, will move water up to 3000 gallons per hour. This pump features a corrosion resistant steel drive shaft, stainless steel impeller, and metal switch arm for strength and durability. This pump is UL/CUL listed and CSA certified and backed by a 1 year warranty.

From the Manufacturer

At Superior Pump we build high quality pumps. With a combined 150 years of pump industry experience every product is built using cutting edge innovative technology and high quality components. Our products are BUILT TO LAST and are supported by an industry standard warranty and excellent customer service. Come see what makes our products different.

• 1/3 HP Sump pump moves up to 3,000 gallons per hour; pump will lift water up to 20' of vertical height
• Tough thermoplastic construction; 10' cord length
• Durable non corrosive steel drive shaft and stainless steel impeller; metal switch arm for strength and durability
• 1-1/4 inch NPT discharge for high capacity pumping
• Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested

User questions & answers

Question:	Are you able to rotate the motor on the shaft to line up the discharge pipe and the float rod to fit the existing holes in your basin cover
Answer:	Yes I have to do that to fit in the sump hole which is a standard plastic 5 gallon bucket recessed in floor.
Question:	Description says cast iron but looks like plastic
Answer:	look close they sale both be sure you order the right one
Question:	How many volts
Answer:	a Normal house outlet of 110 to 120 Volts will work to run your pump . But if your elect go out your pump will not work.
Question:	Is anything else needed to operate? The manual diagram shows a check value. Also, can this be place directly on the basin bottom or is a riser needed
Answer:	Hi there, We do recommend a check valve within a foot or so from the base and attaching it directly to the pump is even better. Thanks.

Product features

Superior Pump 92333 1/3 HP Thermoplastic Pedestal Sump Pump with Automatic Float Switch

Superior Pump builds pumps that are truly Built to Last and are 100 percent factory tested. Superior Pump pedestal pumps use quality components including solid copper motor windings, electronically controlled split capacitors, heavy duty drive shafts, stainless steel impellers and 10 foot power cords. Superior Pump model 92333, 1/3 HP thermoplastic pedestal sump pump, will move water up to 3000 gallons per hour. This pump features a corrosion resistant steel drive shaft, stainless steel impeller, and metal switch arm for strength and durability. This pump is UL/CUL listed (E238091, by UL, 2019) and CSA certified (230584, by CSA, 2019)

Automatic Switch

• Float switch automatically turns on and off pump depending on the water level in the sump basin/pit.
• Metal switch arm for improved peformance
• Thermoplastic rod guide and float ball
• Adjustable switch on height

Construction, Intake and Discharge

• Thermoplastic construction is corrosion resistant and offers years of performance and reliability.
• Top intake filters out debris.
• 1-1/4" NPT discharge for use with 1-1/4" discharge pipe.

Impeller and Drive Shaft

• Stainless steel twin blade impeller for high capacity pumping.
• Non-corrosive steel drive shaft.
• Removable base plate for easy service.

Motor and Performance

Motor

• 1/3 HP Superior Pump continuous duty, thermally protected - split capacitor motor

Performance

• 3000 Gallons per hour at 0'
• 2280 Gallons per hour at 10'
• 900 Gallons per hour at 20'

Product description

1/2 HP, Cast Iron, Submersible Sump Pump, With Vertical Switch, Designed For 11" Diameter Or Larger Sump Basin. Pumps Up To 4200 GPH at 0', Durable Cast Iron Volute, Reliable, Reinforced Poly Carbonate Impeller, Corrosion Resistant Stainless Steel Fasteners, Top Suction Design Filters Debris & Minimizes Clogging, Oil Filled, Thermally Protected Motor Prevents Overheating, Designed For Easy Installation Without Any Plumbing Changes, Epoxy Coated Steel, High Performance 1/2 HP, Motor, 1-1/2" NPT Discharge & Durable Cast Iron Base, Easy Carry Handle For Portability, Float Guard Protects Switch From Hang Ups. This product is assembled in the USA. Easy installation and easy handling.

The Wayne 1/2 HP cast iron submersible sump pump is designed for work in sump pits 11 inches or larger. Its ceramic mechanical seal keeps this pump going in even the most demanding environments, and the 1 1/2-inch discharges creates maximum flow and ensures easy installation. It works 9 inches on level or 4 inches off level. A two-pole switch prevents basement flooding in the event that one pole sticks, and disconnecting 115-volt conductors prevent damage from lightning. The automatic overload mechanism prevents damage to motor windings, permanently lubricated ball bearings need no oiling, and the waterproof three-prong grounding wire with an 8-foot extension reaches distant outlets. Wayne backs its pump with a three-year limited warranty.

From the Manufacturer

Is that noisy sump pump keeping basement dwellers up all night? Equipped with cast iron housing for long life and quiet operation, the Wayne CDU800 sump pump keeps the basement dry and the sleepers asleep. This compact, submersible pump is designed for sump pits 11 inches and up, either 9 inches on level or 4 inches off. Its ceramic mechanical seal assures long life in the most demanding applications. And, its 1- 1/2-inch discharge allows easy installation and ensures maximum flow. A two-pole switch keeps the basement from flooding should one pole stick. And, for added reliability, disconnecting 115-volt conductors prevent lightening damage. The device operates vertically to save space, which makes more room in the basement for boxes, skis, bikes and tools. More great features: an automatic overload mechanism prevents damage to motor windings; permanently lubricated ball bearings require no oiling; a waterproof 3-prong grounding wire with an 8-foot extension reaches distant outlets. A liquid lubricated, ceramic seal prevents water from entering motor housing for years of dependable use and quiet, cool operation. Wayne includes a 3-year warranty.Intended for indoor use only.

Intended for Indoor Use Only.

• 1/2 HP submersible sump pump made of durable cast iron
• Assembled in the USA with foreign and domestic parts
• Ceramic mechanical seal for work in demanding environments
• 1-1/2-inch discharges for maximum flow. Abrasion Resistant Glass Reinforced Polycarbonate Impeller for Reliability
• 3-year limited warranty.High performance; max. flow rate is 5100 Gallons Per Hour

User questions & answers

Question:	is it made in USA
Answer:	Yes it's made in the USA and a very good pump
Question:	Does pump have a cord
Answer:	The CDU800 has a 8 foot water resistant power cord. Thank you.
Question:	Is the wayne 1-1/2 in. check valve with pvc clamps essential for this sump pump
Answer:	It's been a while since I installed, but I'm pretty certain there is a built in check valve of some kind where the discharge pipe fits in. However, I added the additional check valve because 1) the build in one didn't seem very heavy duty, and 2) I had to cut the old discharge pipe to install this anyway, so it was just as easy to clamp on the check valve as a standard rubber connector. When we had our house re-plumbed the professionals put it all back together again with a check valve. I used generic, they used a Zoeller "Quiet" check valve... So while I don't know if it's essential, a check valve of some kind would be worth the few bucks...
Question:	can it run on a 230 volt single phase circut
Answer:	It is designed to operate on a 120Volt single Phase circuit. This is how the internal windings are configured. One would need to rewire the internal configuration in order to work on a 230 volt circuit.If connected as it is shipped would burn out the motor.

Product description

Superior Pump builds pumps that are truly Built to Last and are 100 percent factory tested. Superior Pump uses quality components including solid copper motor windings, heavy duty stainless steel jacketed shaft seals, double o-ring seals on motor plate, and electronically controlled split capacitors. Superior Pump model 92330, 1/3 HP thermoplastic submersible sump pump with vertical float switch, will move water up to 2400 gallons per hour. Equipped with suction screen to filter out large debris and handles up to 1/8-inch solids with ease. This pump is UL/CUL listed and CSA certified and backed by a 1 year warranty.

From the Manufacturer

Superior Pump is a family owned and operated Pump Company specializing in residential / light commercial duty pumps. Headquartered in Minneapolis, Minnesota, Superior Pump was founded in 1999 after spending years in the pump industry dating back to the 70's, and with a plumbing background starting in St Paul Minnesota dating all the way back to 1885. Superior Pump adheres to our strong core family values, selling the absolute highest quality product possible. Known for building durable pumps, Superior Pump concentrates on quality throughout the engineering, manufacturing and testing processes. Quality products, strong warranties, excellent USA based customer service - Superior Pumps Built to Last!

• 1/3 HP Sump pump moves up to 2,400 gallons per hour; pump will lift water up to 25' of vertical height
• Tough thermoplastic construction; 10-foot cord length
• Tethered float switch to automatically turn the pump on/off. Pumps Down To 1/2 inch From Surface When Used As Utility
• 1-1/4 inch or 1-1/2 inch NPT discharge for high capacity pumping
• Superior Pumps are Built to Last, engineered with quality components and are 100% factory tested

User questions & answers

Question:	Does it matter if the float switch is on top of the pump or beside the pump for the pump to work properly
Answer:	Either way works. My float died after a few months. I had to transfer one off an old pump.
Question:	how high will it pump water
Answer:	My pump sits about 2 feet below the concrete in the basement, horizontal for 3 feet and up 9 ft. It is pretty powerful and should eject water pretty high, however you should install a backflow close to the pump so what doesn't get ejected doesn't fall back to the pump, and pump tries to eject in an endless cycle.
Question:	What is the hottest temp water is this pump rated for
Answer:	Hi there,The pump is tater for water temps up to 120 degrees.Thanks
Question:	Can I remove the float switch as I need to use this in a bucket with holes drilled to prevent leaves to drain a pool
Answer:	Just to be clear, I have read more than once in the responses about cutting the tethered float or removing it to use another switch or use the pump as just a utility pump without a switch. There are 2 separate plugs, one to the pump and one to the switch. The switch is not hard wired to the pump and can be removed or not used by not plugging it in. Piggyback refers to plugging the pump and switch together (they are made to plug together then plug into your receptacle) to use in a sump pit to keep water cycled out so as not to burn out the pump. If you want another switch there are many choices like a vertical float switch for limited space in the sump pit, plugs and piggybacks the same way it just positions the switch in a more narrow configuration for a smaller space.

Product features

Superior Pump 92330 1/3 HP Thermoplastic Sump Pump with Tethered Float Switch

Superior Pump builds pumps that are truly Built to Last. Superior Pump uses quality components including solid copper motor windings, heavy duty stainless steel jacketed shaft seals, double o-ring seals on motor plate, and electronically controlled split capacitors. Superior Pump model 92330, 1/3 HP thermoplastic submersible sump pump with tethered float switch, will move water up to 2400 gallons per hour. Equipped with suction screen to filter out large debris and handles up to 1/8 inch solids with ease. This pump is UL/CUL listed (E238091, by UL, 2019) and CSA certified (230584, by CSA, 2019)

Automatic Switch

• Tethered float switch automatically turns on and off pump depending on the water level in the sump basin/pit.
• Piggy-back power plugs allows the pump to be used as either an automatic or manual pump.

Construction and Discharge

• Thermoplastic construction is corrosion resistant and offers years of performance and reliability.
• 1-1/4" or 1-1/2" NPT discharge for use with 1-1/4" or 1-1/2" discharge pipe.

Intake Screen

• Intake screen filters out debris from entering the impeller. This helps reduce the clogging and prolongs the life of the pump.
• Easily to clean and is removable.

Motor and Performance

Motor:

• 1/3 HP Superior Pump continuous duty, thermally protected - split capacitor motor

Performance

• 2400 Gallons per hour at 0'
• 1200 Gallons per hour at 10'
• 540 Gallons per hour at 20'

Product description

Features:



- 1 HP 750W submersible dirty clean water pump, with float switch and 25ft power cord, to help move dirty water away, for household or utility use

- Powerful Pump - Powered by a 1 HP oil-cooled electric motor for draining 3434 gallon per hour quickly

- Safe Use - Built-in automatic power shut off mechanism by auto float switch for preventing the coil from getting burned when pump fails to pump water

- Durability - Engineered Resin Construction for long serving time under water

- Wide Application - Great for household or utility use, such as swimming pools, cellars, garden pond or flooded road



Specifications:



- Overall Dimension(LxWxH): 6 9/16" x 6 1/4" x 14 3/8" (16.7 x 15.8 x 36.5 cm)

- Power Supply: 115V/60Hz/750W (1HP)

- Cable length: 24 11/12 ft (760 cm)

- Q.Max: 3434 gph (13000L/H)

- H.Max: 26 1/4 ft (800 cm)

- Max Submersible Depth: 23 ft (700 cm)

- Diameter of Hose: 1", G1", 1 1/4", G1 1/2" (From Up to Down)

- Max Drainage Temperature: 35ºC

- Max Particle Size: 1 3/8" (3.5 cm)

- Material: PP Plastic, Copper Wire



Package Contents:



- 1x Water Pump

- 1x Manual

• UL CERTIFICATION: 1 HP 750W submersible dirty clean water pump with float switch and 25ft power cord, a safe standard for Swimming Pool Pumps, Fountain Pump, Filters etc. Buy our Sump Pump with Confidence to help move dirty water away, for household or utility use
• SAFE USE: Built-in automatic power shut off mechanism by auto float switch for preventing the coil from getting burned when pump fails to pump water
• DURABLE & STURDY: Heavy duty engineered Resin Construction for long serving time under water, can prolong this submersible pumps life expectancy
• 1 HP WATER PUMP: Powered by a durable oil-cooled electric motor,runs, H.Max: 26 1/4ft, draining 3434 gallon per hour quickly
• WIDE APPLICATION: Ideal for handling such tasks as draining water from a basement or a shallow flooded area, draining or refilling your swimming pool, pond or simply a bath tub, great for household or utility use, such as swimming pools, cellars, garden pond or flooded road

User questions & answers

Question:	How long is the electric cord and what size hose pipe can you use
Answer:	Dear customer, the electric cord length is 25ft, it can fit these hose pipes: 1",G1",1-1/4",G1-1/2"(From Up to Down).
Question:	How many gallons of water does this pump move per hour
Answer:	Not sure but it removes about a foot per hour in my standard built in pool
Question:	What size tubing should I buy to use with this
Answer:	The diameter of pipe can be 1", G1", 1-1/4", G1-1/2" (From Up to Down). You can select one size based on your preference.
Question:	Anyone have a copy of the manual? I can't find it online. Trying to finally close the pool and it won't start for some reason
Answer:	I can't figure out how to copy pictures into this section. And the instructions aren't that good - the english used has incorrect grammar so take that into consideration as well. So I'll type what I think you may need to know. Before using the pump again, first "soak" it so that any possible dirt residues do not block the appliance. Submerge pump at an angle into the liquid so that no air pocket forms on the underside of the appliance. Suction would be prevented by this. Once the pump is submerged, it can be righted again. It also says that we should be using a rope to lower it into the water and not using the main cable..... Minor faults are often sufficient to cause a malfunction.... Pump does not run ----check cables, plug, socket and fuse. Motor defective? contact service partner. Automatic power-off low water level float - manual vertical float motor normal power, start the pump without water, will damage the water pump, manual vertical float when use must be care (I typed this as manual listed it, bad/incorrect grammar, makes no sense) Cleaning the suction area - clean all accessible insides of the casing. Remove fibers which have wound around the rotor shaft by opening the pressure connection. Remove stubborn contamination with a brush and detergent. It also says to if you unable to correct a fault yourself, please contact our technical support directly. BUT there is no number listed anywhere in the 8 page manual. Sorry! This is all the manual says. Not a good manual...

Product features

Yescom 1 HP Submersible Water Pump

Our submersible pool pump features powerful, high efficiency, sturdy construction, lower maintenance costs and works quietly. Ideal for handling such tasks as draining water from a basement or a shallow flooded area, draining or refilling your swimming pool, pond or simply a bath tub.

At Yescom, we strive to provide our customers with great products.

Durable Material

• Sturdy and Solid construction
• UL Safety

Great Powerful Sump Pump

• Power Supply: 115V/60Hz/750W (1HP)
• Heavy duty motor runs underwater about 23ft，empties and fills your pond with ease

Quiet pond pump

• Very silent and quiet, you can't hear the motor run if you’re 10 or 15 feet away

Product description

Quietly and quickly drain your pool or pond in a matter of hours with the EZ Travel Submersible Drain Pump. This pump is perfect for emptying water tanks, ponds, pools, hot tubs, low lying flooded areas, and more. The impact-resistant plastic body is rust-resistant and built to last. This drain kit includes an exploded parts diagram and instructions. Unlike other drain pumps on the market; this model is rated at horse power and can drain a hot tub in minutes. The pump requires little work to operate and is completely submersible. An overheat prevention mechanism automatically shuts the pump off when the water line becomes too low. Sit back and let this EZ Travel Submersible Drain Pump do the work to drain your pool or pond in just a few hours! Spigot Diameter: 1" to 1.25" Dimensions: 9" x 7" x 15" operation and maintenance manual included. Extra Long 25 Foot Waterproof Electrical Cord. 25’ Long 1.5” Diameter Hose Included. Overall Weight: 12.5 Pounds.

• UP TO 3,700 GPH - Submersible and easy to use, this drain pump can go up to 16 feet under water. The automatic shutoff switch eliminates the need to monitor pump progress. Complete with a drain hose, hose clamp, and automatic float switch shutoff feature, this pump takes the hard work out of pool maintenance.
• 400 WATT MOTOR - This transfer pump drains a hot tub in minutes. It’s folding bottom feet allow for maximum low level drainage. This powerful and compact drainage device will help you empty your swimming pool, pond, or hot tub at the end of the season.
• IMPACT-RESISTANT CASTING - Built to last year after year, EZ pumps are made of durable ABS rust-proof plastic housing molds. This EZ Travel Collection submersible drain pump combines portability, reliability, and power.
• COMPLETE DRAINAGE KIT - This pool drain pump comes with a 20 foot waterproof cord that can be used with just about any standard outdoor water house. Plus, the removable and adjustable spigot fits a variety of hoses and makes pump maintenance simple.
• DIMENSIONS – Pump: 9" x 7" x 15". Drain Hose Length: 20’ Drain Hose Diameter: 1.5” Weight: 12.5 Pounds.

User questions & answers

Question:	Can anyone explain how to use the folding bottom feet? I’ll be draining a spa. Do you fold the feet to drain the last few inches
Answer:	Yes fold the feet. It will not drain all water out. It leaves half inch to inch in spa. You will need to scoop the remaining water out.
Question:	Does anyone know about how long this pump would take to drain a 320 gallon hot tub
Answer:	The product title says 3,700 gallons per Hour. I drained a 15,000 gallon pool in about 22 hours. I was very happy with it's performance it was as fast as the ones I used to rent.
Question:	Can I use my existing 2" backwash hose with this pump to drain the swimming pool
Answer:	The answer is likely yes. The nozzle on the pump is tapered so it allows different sized hoses to be clamped on.
Question:	will this drain a pond that has a lot of silt and muck (does it have a filter
Answer:	It has no filter but does a decent job of draining with a lot of debris.

Product features

Hot Tub and Swimming Pool Drain Pump with Hose Pond/Flood Pump

Submersible drain pump is capable of pumping up to 1,800 gallons of dirty water an hour. It can drain a hot tub in minutes!

Folding Bottom Feet

The newly designed folding bottom feet allow you to extract that last bit of low lying water. An overheat prevention mechanism that automatically shuts it off when the water line becomes too low.

Versatile

Great for draining water tanks, ponds, pools, hot tubs, basements, etc.

Portable and Powerful

Dimensions: 9" x 7" x 15"

Extra Long 25 Foot Waterproof Electrical Cord.

25’ Long 1.5” Diameter Hose Included

Overall Weight: 12.5 Pounds.

1.5 Horse Power