12 best electric heating systems

Product description

Turn those chilly tile floors into warm and cozy with HeatTech electric radiant floor heating system and enjoy the benefits of quiet operation, affordable cost and unmatched comfort levels of radiant heated floors. Electric floor heating offers a healthier alternative to traditional heating systems such as forced air and baseboard/radiators, both of which dry the air and require purchase, installation and maintenance of expensive parts and equipment.



What’s included:

HeatTech™ Electric Radiant Floor Heating Mat (HTMAT);

OJ Microline UDG-4999 Thermostat with Class A GFCI (for wet/dry locations - incl. bathrooms, kitchens, etc.), 7-day programmable;

OJ Floor Sensor with 15ft lead wire;

Installation Manual.



Applications:

Tile (Porcelain/Ceramic/Glass), Stone (Granite/Slate/Marble/Pebble) floors;

Bathrooms, Kitchens, Mudrooms, etc.;

Supplementary or Whole-house heating;

Residential homes and apartment buildings;

New construction and retrofits.



HeatTech™ System Benefits:

HeatTech floor heating mats are UL listed for USA (meet and exceed highest electrical safety standards);

HeatTech mats feature a sticky/adhesive backing for easy adhering to variety of surfaces, making installation much faster and easier;

Our heating cable is only 1/8" thick and will not raise the floors significantly;

Cable spaced at 3" apart for optimal performance and outputs as much as 41 BTU’s per sqft, making the system suitable for whole-house heating applications;

A single 10ft long cold lead means no extra wiring or drilling;

Does not dry air like steam radiators and forced air heating;

Zero Electromagnetic Field;

Quiet operation.

• Electric floor heating mat specs: 20 sqft (20" wide x 12.2ft long), 120V, 2.0A, 240W; 3" cable spacing, 12 Watts/sqft output (41 BTU/sqft)
• Thermostat UDG-4999: GFCI (Class A) protected for wet/dry locations, 7-day programmable, 120/208/240V + 15ft floor sensor
• ADHESIVE backing - Mat lays flat and stays flat, no stapling needed.
• UL listed for USA and Canada. 120V mats can be combined to heat up to 150 sqft of space using a single thermostat. Mats must be wired to the thermostat in parallel.
• Heating cable only 1/8" thick. Zero EMF. Single 10ft Cold Lead. 25-year warranty.

User questions & answers

Question:	Can this be separated into strips of 4 foot
Answer:	the instructions state that the heat wire can’t be shortened
Question:	Can i put this product under laminate flooring and not just tile
Answer:	You can purchase a heater to go under a floating laminate floor. It has a felt backing. This particular one is designed for Tile.

Product description

ENJOY THE BEAUTY AND PRACTICALITY OF A HARD FLOOR WITHOUT COMPROMISING ON COMFORT

The luxury of a heated tile floor in the cold months is a pleasure that must be experienced to be truly appreciated

LuxHeat mats can be cut, turned, flipped, or have wires removed to accommodate any room shape or size

Controlled by OJ Microline's Intuitive Programmable thermostat to become one of the most versatile, easy to install heating systems

BEST SUITED FOR:

★ Residential homes, Office apartments and Senior living facilities

★ Under tile, stone, marble, laminate and engineered wood floors

★ Can be installed as primary or secondary heat source

HEATING MAT FEATURES:

✔ Zero EMF (Electromagnetic Field)

✔ Double insulated, single cold lead

✔ UL listed for USA, suitable for wet locations

✔ Twin conductors, Alu foil sheath and ground wire

✔ 12watts/sqft @ 3" spacing provides optimal heat distribution

✔ Self-Adhesive mesh on one side and double sided tape on the other, ensures mat stays flat even when flipped

THERMOSTAT FEATURES:

✔ 120 Volt

✔ c UL us Listed

✔ GFCI Class A 5mA

✔ Dual sensing(Air & Floor)

✔ Load: 15A-1800w@120v, 3600w@240v

✔ Large backlit display with Intuitive menu

✔ Other Modes: Child lock, Manual override & more

✔ Compatible with most radiant Floor Heating Systems

✔ 7-Day Program, pre-set program can be customized to suit one’s lifestyle

Cable Monitor: Includes batteries

BENEFITS:

✔ Versatile, Fast & Easy to install, Easy to Use

✔ Recommended by Health Professionals for Allergy sufferers

✔ No unattractive heaters, storage hassles, maintenance, or smell

✔ Safe for Children, Elderly and Pets - No hot, exposed or moving parts

✔ Accurate and Intelligent control ensures your Personal Comfort and Affordability

 

• LUXURY AND COMFORT - Enjoy the warmth of LuxHeat's easy to install Electric Floor Heating System. The LuxHeat Heated Floor Mat is best suited for installation under Tile, Stone, Laminate and Engineered Wood flooring. Heater Kit Includes - Self-Adhesive Heating Mat, OJ Microline UDG-4999 Programmable Thermostat with Floor Sensor and Built-in GFCI (Ground Fault Protection), plus Cable Monitor/Alarm.
• EASY TO INSTALL - The 3" Pre-spaced Electric Floor Heating Mat can be cut & turned, flipped or rotated - providing coverage where neded. With Self-adhesive mesh on one side and double sided tape on the other, the mat adheres to the sub-floor and lays flat even when flipped. The single point power connection makes for easy wiring, and the less than 1/8" heating cable ensures minimal effect on finished floor level.
• QUALITY & EXPERIENCE - With a combined experience of over 50 years, the LuxHeat Tech team offers a wide range of high quality, UL Certified products . Includes 10-Year Manufacturers warranty - providing Peace of Mind and an assurance of performance for many years to come. LuxHeat's radiant floor heat Cables and mats are UL approved and Safe for Wet Locations.
• PROGRAMMABLE THERMOSTAT - The OJ Microline UDG promotes sleek modern design and intuitive control, making it easy to install and easy to use. The 120 Volt, 15 amp thermostat includes an integrated Class A GFCI (ground fault protection), External floor sensor, and offers Dual (air & floor) sensing capabilities. Features 7-day Program Schedule, providing maximum comfort, while reducing operating costs, power logging, child lock and more. cULus approved for USA and Canada. 3-year Factory Warranty.
• TECHNICAL DETAILS for Heated Mat - Size: 30 Sqft (20" x 18.30'), 12w/Sqft @ 3" wire spacing's (120v) 360w. Twin conductor heating wires, and drain wire with Aluminium sheath , ensures ultra low EMF. Cable Monitor/Alarm includes 2xAAA batteries.

User questions & answers

Question:	Can this be installed in a shower? Waterproof
Answer:	Hello, yes the LuxHeat system is rated for wet areas, however as with all heating for wet areas, the splice (joint between element/burgandy wire and cold lead/black wire), must be outside the shower. In the case of the mat, you can simply remove the tape holding the first 2-3 feet of wire and place the splice outside the shower by about 2 feet.
Question:	What is the actual length of the mesh? I'm finding 2 different answers
Answer:	Hello, the 20sqft mat is 12.2ft long by 20inches wide.
Question:	Does this need to be installed the mesh in a bed of mortar first or can I apply my mortar as I tile and do it all in one step
Answer:	Hello, you can apply your mortar as you tile, however if you choose this method to install you must make special effort to see that all wires are well covered with mortar. If a heating wire is not covered with mortar there will be no heatsink and the wire will run to hot. As long as the wires are well covered it'll be fine.

Product description

HeatTech Electric Radiant Floor Heating Cable is perfect for:

Tile, Stone, Granite and Marble floors

Bathrooms, Kitchens, Showers, Saunas and others

Both new construction and retrofits

Residential homes and apartment buildings

Whole house heating

What's included:

Electric radiant heating cable on a spool

Cable guides – 25ft roll is required for every 200ft of cable

Detailed installation manual

Honeywell/Aube TH115-AF-120S thermostat with floor sensor



Features:

HeatTech floor heating cable is UL listed for USA (complies with electrical safety standards).

Heating cable is only ~1/8" thick and will not raise the finished floor significantly.

Zero Electromagnetic Field.

Made using the highest quality materials in the industry.

Comes with a single armored 10ft long cold lead wire for easy connection to the thermostat – no extra wiring or drilling.



Benefits:

Helps to create incomparable levels of comfort

Fast & easy to install

Energy-efficient

Compatible with all brands of domestic floor sensing thermostats, including Honeywell/Aube and many others;



Sizing & Installation:



Sizing is easy – simply select a HeatTech cable with area coverage which corresponds to the size of the heated area.

120V system allows for installation of up to 600ft of heating cable (150 sq. ft. at 3” spacing) on a single thermostat.

System allows to connect up to 3 separate cable runs to a single thermostat to match the size of the heated area.

Installing cable at 3” spacing is recommended for optimal heat output.

• Area Coverage: 15 sqft @ 2" spacing; 20 sqft @ 3" spacing (recommended), 25 sqft @ 4" spacing.
• Heating Cable Length: 80ft + cold lead (10ft)
• Voltage: 120V; Output: 240W (3W/ft.); Amperage: 2 Amps
• Heating cable is only ~1/8" thick and will not raise the floors significantly.
• UL listed for USA and comes with a 25-year Manufacturer Warranty

User questions & answers

Question:	is this the right product for tile over concrete slab floor
Answer:	Yes it is
Question:	I screwed up and didn't embed the thermostat thermometer wire into the floor. Is there anything I can do to control the temp w/o tearing up floor
Answer:	The thermostat can run on the ambient setting.
Question:	can you link this to another system? i have a 3x5 matt called perfectly warm tile floor heat i was planning on installing
Answer:	Avoid mixing different brands of heating mats/cable, as it will automatically void the warranty for both.
Question:	Can this wire also be installed under the tile in the shower
Answer:	Don't see why not, as long as it's properly encased in cement. We pour a layer of flour leveling cement over our installs.

Product description

ENJOY THE BEAUTY AND PRACTICALITY OF A HARD FLOOR, WITHOUT COMPROMISING ON COMFORT

LuxHeat's wide range of 120v and 240v loose-lay Cables & Strapping, offer the ultimate in design flexibility, allowing for custom configurations and easy installations

KIT INCLUDES:

✔ Heating Cable

✔ Cable guides/Strapping-Devi by Danfoss

✔ Cable Monitor-with Batteries

BEST SUITED FOR:

★ Residential, Office apartments and Senior living facilities

★ Installs under tile, stone, marble, laminate and engineered wood floors

HEATING CABLE FEATURES:

✔ 10 Year manufacturer’s warranty

✔ UL listed for USA, classified as safe for Wet Locations

✔ 12watts/sqft @ 3" spacing provides optimal heat distribution

✔ Ultra low EMF - Dual conductor Tech, Alu foil sheath and ground wire

✔ Heater wire is less than1/8” thick, ensures minimal effect on finished floor height

✔ Ultra low EMF (Electromagnetic Field) Dual conductor Tech, Alu foil sheath and ground wire

✔ ETFE insulated and covered by tough outer jacket, providing protection against abrasion and corrosion

THERMOSTAT FEATURES:

✔ c UL us Listed

✔ GFCI Class A 5mA

✔ Dual sensing(Air & Floor)

✔ Dual voltage(120v & 240v)

✔ Load: 15A-1800w@120v, 3600w@240v

✔ Modes: Child lock, Manual override & more

✔ 3.5” Colour screen with easy interactive Touch control

✔ 7-Day Program, can be customized to suit one’s lifestyle

BENEFITS:

✔ Recommended by health professionals for allergy sufferers

✔ Safe for children, elderly and pets - No hot, exposed or moving parts

✔ Accurate and intelligent control ensures personal comfort and affordability

✔ Out of sight, no unattractive plug-in heaters, no storage hassles, no maintenance and no smell

WATT DENSITY:

★ 14.00w/sqft @ 2.6"

★ 12.00w/sqft @ 3"

★ 9.00w/sqft @ 4"

• LUXURY AND COMFORT - Enjoy the warmth of LuxHeat's easy to install Electric Floor Heating System. The LuxHeat floor heating cable is best suited for installation under Tile, Stone, Laminate and Engineered Wood flooring. Heated floor kits Include - Heating Cable, OJ Microline Programmable Touch Screen Thermostat with Dual Sensing and Built-in GFCI (ground fault protection) # UDG4-4999, Cable Guides/Strapping, and Cable Monitor/Alarm to provide peace of mind when installing heater wire.
• VERSATILE - LuxHeat's range of loose lay/ free-form underfloor Heating Cables and Cable Guides offers unlimited design flexibility. Customized configurations ensure warm floors for any shape or size room. Dual conductor/Single point power connection makes for easy wiring. Heating wire at less than 1/8" diameter ensures minimal effect on finished floor level.
• QUALITY & EXPERIENCE - With a combined experience of over 50 years, the LuxHeat tech team offers a wide range of high quality, UL Certified products . Heaters carry a 10-Year Manufacturers warranty, providing Peace of Mind and an assurance of performance for many years to come. LuxHeat radiant floor heat Cables and mats are UL approved and Safe for Wet Locations.
• PROGRAMMABLE THERMOSTAT - The 120v OJ Microline Touch Screen offers modern design and intuitive control, making it great looking, easy to install and easy to operate. Features include Dual sensing (air & floor), power logging, child lock, self-learning, 5-year program back-up. The 7-day Program Schedule provides maximum comfort, while reducing operating costs. Includes a Built-in 'Class A' GFCI (ground fault protection). cULus approved for USA and Canada. 3-year Factory Warranty.
• TECHNICAL DETAILS - Cable Length: 400ft. 1200watts (120v), 10.0 Amp. Coverage: 100 Sqft @ 3" spacing - 12w/Sqft. Dual wire technology, and drain wire with Aluminium sheath, ensures ultra low EMF. Single armoured cold lead. LuxHeat - Providing the right under tile floor heating system for you.

User questions & answers

Question:	Will this work installed underneath the floor in a crawl space
Answer:	Hello, this type of floor heating system is best used above the sub-floor, covered by a self-leveling compound or thin-set.

• 300 Sqft Cable with Digital Programmable Thermostat, Electric Floor Heat Warming System
• Includes Plastic Cable Guides and Installation Monitor
• 240V, 15.0 Amps, 3600W, consists of 2 spools, 12 Watts/Sqft, UL Listed for USA and Canada
• Honeywell/Aube Digital Programmable Thermostat # TH115-AF-240, Includes floor sensor
• Made in the USA using the highest quality materials, Single Cold Lead, 25 year Warranty

User questions & answers

Question:	Could this be used in a concrete slab? (Considering it as a primary heating source
Answer:	The heating system can be installed on top of a concrete slab. We recommend using some type of insulation, such as CeraZorb Thermal Break Underlayment which we sell through our website, on top of the concrete slab to help reduce heat loss through the concrete. Our heating system is used to warm the floor and will warm the room. With 3" spacing the system supplies 12 watts/ square foot.
Question:	Any recommended method to run the cord up stairs (only 2 stairs)? Also, will this work with 20amps or does it need 30amps because it's 240V
Answer:	The wire has a minimum bend radius of 1 inch, therefore you can't put the wire at a 90 degree angle up the stairs. The wire must always be embedded in a cement based mortar. The 300 sq. ft. 240V cable system is 15 amps. Please follow local codes, but a 20 Amp breaker should be sufficient.
Question:	Can this be used under solid oak hardwood flooring
Answer:	The floor heating system should not be used under a wood floor that will be nailed or screwed down. Regardless of the type of flooring, the floor warming system needs to be embedded in a cement based mortar. Please check with flooring manufacturer to verify flooring can be installed over an electric floor warming system.
Question:	How many linear feet is there to make up the 300 sq ft
Answer:	The 300 sq. ft. 240V cable system consists of two spools totaling 1200 LINEAR FT. The two spools are connected in Parallel at the thermostat.

Product features

Floor Heating Cable

The Electric Floor Heating Cable consists of a spool of heating cable.  Simply run the cable 3" apart across the area to heat using the cable guides to secure to the floor running the cold lead up the wall to the electrical box.  These heating systems are ideal for odd shaped areas or to heat around objects.  The RED HEATING ELEMENT CAN NOT BE CUT, so be sure to accurately measure the space you are heating.

Programmable Thermostat with Sensor

Honeywell / Aube model # TH115-AF-240S

The programmable floor sensing thermostat and floor sensor is designed to work with electric floor heating systems. It gives you the ability to accurately control the floor temperature for maximum comfort and energy savings. The thermostat features high-tech precision with straight forward, user friendly interface and contemporary design with backlit display. This floor sensing thermostat is digital, programmable, and includes the floor sensor. The thermostat is factory pre-programmed with a 7 day schedule that can be adjusted. This thermostat is 240 volt, rated for 16 amps, easily switching between F and C temperature scales.

THERMOSTAT FEATURES

• AF mode-controls ambient temperature with floor temperature limitation
• F mode controls the floor temperature using an external temperature sensor
• Two temperature sensors-one in floor, one in thermostat for accuracy and security

Installation Monitor

The Installation Monitor can help give you peace of mind while installing the floor warming system.  Connect the system leads to the monitor prior to installation.  The monitor will "scream" a warning in the event the heating element is cut or damaged allowing you to make any necessary repairs before the heating system is embedded in mortar.  If the alarm sounds, stop work and consult the operation manual.  We still recommend checking the ohms of the floor heating system with a multimeter before, during, and after installation.

• Red light and alarm indicates lead wires have come loose from the terminals or damage has occurred to the heating system
• A white light indicates the monitor is operating
• Can monitor up to 3 systems at one time when they are temporarily connected in series

CABLE GUIDES

Designed for fast installation of the the heating cable, simply loop the floor heating cable around the guide as you lay the cable system across the subfloor.

Secure the cable guides according to the planned layout using screws, nails, adhesive or glue approved for use with the given subfloor.  The heating element should be spaced 3" apart across the area to be heated.  Cable guides should be run perpendicular to heating cables.  The heating cables should have a minimum distance of 2" from walls and objects. Spacing between cable guides should not exceed 36" in distance.  Secure the heating element to cable guides by wrapping the wire around the stud.  Maintain moderate tension of cable throughout installation.  Do not twist heating element and keep the minimum bending radius of the cable to 1".

Cable guides are 12" long and can be cut to length. Includes enough cable guides for cable heating system.

MADE IN USA

Warming Systems is proudly Made in the USA. Our manufacturing facility and offices are located in Spring Grove, IL (just outside of Chicago). Our systems are made from the highest quality products and offers the best heating technology on the market.

• 50 Square Feet Heating Mat. 20 inches wide x 30.5 feet long. Includes GFCI Thermostat, 240V
• Premier Heating Cable Designed for Longevity, 15 ft Single Cold Lead, 12 Watts/Sqft Heating
• Listed for Wet Locations. Thin profile ~1/8" thick. Mesh can be cut to desired configuration.
• ETL Listed for US & Canada - Limited Lifetime Warranty by 20 Year Trusted USA Manufacturer
• Voltage: 240V - Amps: 2.5 - Watts: 600

User questions & answers

Question:	when applying on a wooden subfloor, does a membrane have to laid first? if so, what kind
Answer:	A membrane is not required, but if desired there are no restrictions to what kind to use. As long as the Mat is fully embedded in Thinset and/or mortar, it will work great.
Question:	do i need to purchase anything else besides what comes in this package? is this the complete heating kit
Answer:	This comes with the heating mat, thermostat, floor sensor and installation manual.
Question:	How many electric heating mats can I put together
Answer:	The thermostats can handle 15 amps each. You could connect more mats to a larger circuit with a relay or contactor also but for usage with the thermostat that comes with these using 240V and 15 Amps max it would be 240V * 15A = 3600 watts total. These mats produce 12 watts per sqft so 3600 watts/12 watts per sqft = 300 square feet on 240V. It would be half (150 sqft) of that if you use our 120V mats.
Question:	What's the best underlay for this (over concrete flooring)? tyvm
Answer:	for concrete sub floors you don't really need an underlayment since these system are already going to be embedded. You can use an uncoupling membrane over it if you really want an underlayment.

Product features

Programmable Thermostat

Heatwave standard thermostat (M429) specifications:

• Up to 4 event programming
• Simple user interface
• Pre-programmed for quick set up
• Multi voltage: 120/208/240 V
• Output Relay 15A
• Can be set to automatic, manual, or comfort mode
• Includes 2 sensors: a built-in air sensor and floor sensor thermistor with 10 feet of NTC (12K) sensor cable
• Temperature control range: 41ºF to 104ºF
• Class A GFCI (5 mA trip level)

An Efficient System

The Heatwave system comes with a 10-foot long floor sensor standard for optimal use of your Heatwave System. Extra compatible sensors are available on our store page.

Fully Embedded System

Heatwave can be embedded in various types of cement-like material, allowing for several floor covering options. Embedding Heatwave allows for optimal heat dispersion and gives the end-user a nice, consistently warmed floor.

Be sure to get the right size!

Heatwave comes in various sizes to accommodate differing size spaces. It is important to accurately measure the space you intend heat. Avoid placing the heating cable under vanities, within 6-inches of the toilet gasket and under other permanent fixtures in the space. It is acceptable to place Heatwave in a shower, provided that is still fully embedded in a thinset/or Mortar.

Be aware the heating cable cannot be cut or shortened in anyway.

Need a larger System?

The 240 volt systems are perfect for larger areas, or for lowering the amp load. 240 volt systems require one circuit capable of 15 amps (max).

Product description

A gentle electric radiant heat system designed specifically for dry installation under floating wood and laminate floors. A low profile, line voltage system, it features gradual warmth from low wattage resistance heating of ultra-thin, flexible radiant heat film.



Installed easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12 watts per square foot to gently raise the temperature of the floor, conforming to the warranty requirements of many floating floors. The system, which sports an impressive 99% efficiency, includes temperature limiting properties so the film does not overheat.



APPROVED FLOOR COVERING MATERIALS

• All Floating Floors

• Floating Tiles

• Laminate Flooring

• Engineered Wood

• Luxury Vinyl Flooring (4mm or thicker)

• Cork and Bamboo

* Refer to Floor Covering Manufacturer's specifications for compatibility of their product over any radiant heat before installation.



Its available in four convenient rollout mat sizes that will accommodate most any layout. Each mat has wires pre-attached for ease of installation.



• Uses an highly-efficient conductive ink technology

• Consumes up to 50% less power than traditional wired systems

• Easy to install: roll out, cut length to fit if needed and run pre-attached wires to a wall thermostat

• No mortar and no mess

• Conforms to many floating floor manufacturers requirements

• Disperses an evenly consistent heat throughout the entire floor

• ✔ EASY INSTALLATION - 3 Simple Step Process (1. Install Underlayment, 2. Roll Out Electric Radiant Heat Film & 3. Install final floor covering)
• ✔ MINIMAL THICKNESS PROFILE - Ultra-thin (less than .016") heated panels keeps same floor heights through room transitions
• ✔ PROVIDES UNIFORM HEAT - Your floor is heated uniformly with no gaps and the radiant heat is dispersed evenly through the room
• ✔ QUIETS YOUR FLOOR - Used in combination with QuietWalk underlayment, you achieve a superior sound rating: IIC 71 & STC 67
• ✔ SAFETY CERTIFIED - ETL in compliance with UL Standards for radiant flooring in the USA and Canada
• ✔ COST LESS TO OPERATE - Even heat distribution allows the QuietWarmth systems to cycle quicker resulting in less energy consumption
• ✔ MAINTENANCE FREE - Crafted to not completely shut down if the system should ever become compromised or damaged
• ✔ MAT SIZE: 1.5 ft x 10 ft - 240V

User questions & answers

Question:	Do I need to buy a thermostat to control it? Or can it be connected to a switch? Just on and off
Answer:	You need a thermostat to install it properly - SAFELY. The mats are standard 110 / 120 volt hot & neutral. You could wire it to a switch and the mats will not care. The Tstat's most important role is turning the mats OFF, not on. Without a stat the mats are just going to keep making heat until you turn them off, maybe after the house burns down, maybe not. No switch, timer, photocell...whatever you employ to control the mats is going to take the place of a thermostat for a proper and safe installation. Anything else would be reckless.
Question:	What underlayment is recommended for this heating film
Answer:	I laid it right on the tile. Works great.
Question:	Can these be cut and wired in a series to one thermostat
Answer:	yes
Question:	Planning 1 mat 1.5x5 = 90 watts. Can I use this w/o thermostat? Just on a gfci protected circuit w/ off/on switch
Answer:	Yes. I did this and it works just fine. I could not find an inexpensive thermostat that would operate properly on such a low load / resistance so I just hard wired with a cut off switch. No problems so far and installed about 6 months?

Product features

QuietWarmth Radiant Heat Film for Floating Wood and Laminate Floors

Installs easily over a subfloor or over an acoustic/insulating underlayment as part of the overall floor assembly, it uses just 12 watts per square foot to gently raise the temperature of the floor. The system, which sports an impressive efficiency, includes temperature limiting properties so the film does not overheat. Its available in four convenient rollout mat sizes that will accommodate most any layout.

• Use with most floating laminate, engineered wood and floating tile floors
• Uses an highly-efficient conductive ink technology
• Disperses an evenly consistent heat throughout the entire floor
• Will not add extra height to the floor, only 0.016 in. thick
• Easy to install: roll out, cut length to fit if needed and run pre-attached wires to a wall thermostat
• No mortar and no mess
• Conforms to many floating floor manufacturers requirements

Provides uniform heat and cost less to operate

Your floor is heated uniformly with no gaps and the radiant heat is dispersed evenly throughout the room. Even heat distribution allows the QuietWarmth systems to cycle quicker resulting in less energy consumption. Also the heat will never exceed 85 degree F, allowing your feet to have the perfect temperature.

• 120V mats work with QuietWarmth 120V systems. 240V will work with 240V.

There is no easier radiant floor heating system to install.

Simple 4 step process!

1. Install underlayment.
2. Roll out electric radiant heat film
3. Hook up electric wiring
4. Install final floor covering

Floor Covering Materials

• All Floating Floors
• Floating Tiles
• Laminate Flooring
• Engineered Wood Flooring
• Luxury Vinyl Flooring (4mm or thicker)
• Cork and Bamboo

Note: Refer to Floor Covering Manufacturer's specifications for compatibility of their product over any radiant heat before installation

• HEATIT warm mat was used underneath of many popular flooring material such as ceramic tiles, natural stones, wood, and so on. One piece 90 sq. ft. mat consists of a heating cable secured with double-sided tape onto a fiber-glass mesh.
• UL LISTED for USA and Canada. Fluoropolymer (One of the most heavy duty plastic material) as the insulation. Can be used for wet application, but not for installation in pool and spa areas, nor outdoor use. 30 years limited warranty for the heating mesh. The limited warranty is valid based on correct installation methods and completion of all test requirements.
• Mat size: 20" width, 54.9’length; Voltage: 120V, Amps: 9.0A, Watts: 1080W. Output: 12 Watts/Sqft. The yellow heating element cannot be cut. The mesh material can be cut to make turns and angles to heat just about any shaped area. A more detailed installation process is outlined in the instructions.
• Ultra-thin & durable heating element (Only 1/8" thick), Pre- spaced wire attached to a tough fiberglass mesh backing, Cable cannot be cut, but the matting can be, to allow you to turn a corner or reverse direction.
• Fully self-adhesive underlay for ease of laying along with complete and comprehensive installation instructions for your convenience. used in conjunction with the thermostat controller. Easy install to your shower room, kitchen room, wet room, living room, greenhouse and so on. Recommended cooperate with HEATIT GFCI Thermostat to work.

User questions & answers

Question:	Does this product support under carpet (above padding) application
Answer:	Yes, you can use carpet above the floor.
Question:	Would this work to keep a water storage tank possibly from freezing, if wrapped? I know its a little off question, but thanks in advance
Answer:	We recommend you choose HEATIT JHSF or JHSF1.
Question:	Can i put this under an area rug
Answer:	It can not put under the rug directly. First, install insulation material, then pave heating mats, after that pave concrete, and install flooring. And above the flooring, you can put a rug.
Question:	Can I shorten the black, white, and ground wires of the supply line. (Not the heating cable
Answer:	Yes, you can cut the cold lead.

Product features

HEATIT WARMMAT Electric Radiant Floor Heating Mat

Ideal for renovations, the heating mats provide warmth throughout the whole room, giving a whole new meaning to heating and comfort.

Floor Heating Mat

Programmable Thermostat with sensor(Not included, Sold individually)

Installation Monitor (Not included, Sold individually)

Mat Turns and Fill-in Techniques

• This table contains some of the common turns and techniques used to layout around corners, angles, and built-ins.
• Carefully cut the red mesh to make turns. Never cut, nick, or otherwise damage the heating wire.

Mat Turns and Fill-in Techniques

• This table contains some of the common turns and techniques used to layout around corners, angles, and built-ins.
• Carefully cut the red mesh to make turns. Never cut, nick, or otherwise damage the heating wire.

Mat Turns and Fill-in Techniques

• This table contains some of the common turns and techniques used to layout around corners, angles, and built-ins.
• Carefully cut the red mesh to make turns. Never cut, nick, or otherwise damage the heating wire.

Mat Turns and Fill-in Techniques

• This table contains some of the common turns and techniques used to layout around corners, angles, and built-ins.
• Carefully cut the red mesh to make turns. Never cut, nick, or otherwise damage the heating wire.

• Listed and Safe for Wet Locations. Thin heating element profile ~1/8" thick. Highest Quality Heating Cable Designed for Longevity by USA Manufacturer with 20 years industry experience.
• Includes Required GFCI Programmable Touchscreen Thermostat with Floor Sensor for maximum efficiency.
• Complete Kit with testing/monitoring devices, mounting/installation hardware, and trowel.
• ETL Listed for US & Canada - Limited Lifetime Warranty on Heating Element - 3 Year Limited Warranty on thermostat.
• 20 Square Feet - 120 Volts - Amps:2 - Watts: 240 - 15 ft Cold Lead - 12 Watts/Sqft - 20 Inches Wide x 12.2 Feet Long.

User questions & answers

Question:	Is the thermostat wifi capable? If not, can i use any thermostat with the flooring system
Answer:	The thermostat that comes with this kit is not WIFI capable, however, we do offer a WIFI model as an upgrade option. Please contact us for more information 1-888-239-1232.
Question:	can this be wired with a GFCI already present protecting the circuit
Answer:	Yes, that's not a problem.
Question:	Does this work with 220v
Answer:	Hello, this one is designed for 120V, but we do have 240V Heatwave Kits on Amazon also.
Question:	Since there are two mats, how are they interconnected? There's a big difference between connected in the thermostat box or inline
Answer:	Both mats need to be wired directly to the thermostat to function properly.

Product features

Touchscreen Programmable Thermostat

The M429-TS is a sleek, touchscreen floor-warming, programmable thermostat that includes the safety of built-in GFCI protection with the accuracy of a standard floor sensor and several programming modes, schedules and events.

Monitoring Your Installation

The Heatwave Premium Kit comes with a floor alarm that once installed, monitors the heating element for damage. Floor alarm (sometimes known as a "screamer") is a battery-operated device that monitors for breaks in continuity along the entire floor heating cable and if the circuit is broken, the device "screams," allowing for damage to be assessed and proper remedies to be taken.

Trowel

Using a metal trowel can be risky if the heating element accidentally gets knicked or cut. Ideally, using a plastic trowel is the best bet, however they can be hard to find. We've included this plastic trowel to take away the concerns about knicks/damage, while making the solution easy and convenient.

Easy-to-use Digital Multimeter

With this easy-to-use digital multimeter, checking the pre, during, and post condition of the heating element is easy and fast. No more wondering which meter will work or give the appropriate readings. Follow the instructions in the Heatwave Manual to check resistance, ground, and the sensor easily and efficiently.

Single-Gang Electrical Box

No more wondering about what size box to use for the thermostat. We include a single-gang, old-work style electrical box with every Heatwave Premium Kit.

Extra Mounting Hardware

Sometimes when installing the Heatwave system, it would be nice to have clips to be able to accommodate special installations outside of the mat configuration or when using the free-roll cable. These clip kits with nails allow the installer to make custom runs of cable to go around obstacles, or go into hard to reach places.

Be sure to get the right size!

Heatwave comes in various sizes to accommodate differing size spaces. It is important to accurately measure the space you intend heat. Avoid placing the heating cable under vanities, within 6-inches of the toilet gasket and under other permanent fixtures in the space. It is acceptable to place Heatwave in a shower, provided that is still fully embedded in a thinset/or Mortar.

Be aware the heating cable cannot be cut or shortened in anyway.

• 10 Square Foot Under Tile Heating Mat, Mat is 20” Wide x 6’ Long, 120 Volts
• Mat has double sided tape (Adhesive Backing) to stick to floor. Lays FLAT for easy installation.
• 120V, 1 Amp, 120W, 12 Watts/Sqft, UL Listed for USA and Canada, Cable is 1/8” thick
• Honeywell/Aube Digital Programmable Thermostat # TH115-AF-120, Includes floor sensor
• Made in the USA using the highest quality materials, Single Cold Lead, 25 Year Warranty

User questions & answers

Question:	I need 24" x 60".. Can I route the last one feet wire along the side to increase the width to 24" and keep the length to
Answer:	You can loosen the heating element from the mesh and put along side the mat keeping it at 3" spacing.
Question:	I am planning to install wooden floor (hardwood or laminate) in my bathroom. Can I use this system to heat wooden floors or is is for tiles only
Answer:	The floor heating system can be installed under laminate or engineered wood floors, but not a traditional wood floor in which you are nailing down the floor because of the risk of putting a nail through the wire. Regardless of the flooring type, the floor heating system must be completely embedded in a polymer modified cement based mortar.
Question:	I have a concrete slab that I would like to add electric floor heating and tile over it. How do I avoid moisture build up with this product
Answer:	You need to seal your concrete floor! Theres a great product on amazon here that gets down into concrete and seals up everything--it even pushes dirt and moisture out as its sealing! and you just spray it on. Its advertised to block radon, but its all the same different of sealing concrete (will make moisture barrier, block radon, etc.) I think its just called "Radonseal" and its in a big bucket; you'll also need a 1 gallon sprayer, they run about ten bucks. I would seal it before installing this product, as you'll get a lot more out of it. You'll still want to cover it with something so it can distribute its heat (like put in thinset or something like that) it doesn't have to be fancy tile. I did mine in thinset and threw a rug over it to make a warm place for my pets while i'm at work.
Question:	Can this be used when installing a drop-in tub to keep bath water warm
Answer:	No, but Kohler has a tub that has a built in heating element on the portion where you lean up against. I don't know how well it would heat the water, but I bet it would be nice.

Product features

Floor Heating Mat

The Electric Floor Heating Mat consists of a mat with the cable heating elements pre-spaced 3" within the mat. Simply unroll the floor heating mat with the cold lead running up the wall to the electrical box. These heating systems are ideal for rectangular or square areas with right angles. You can manipulate the mat to fit the desired heating area by using the turning techniques shown below. The white fiberglass mesh may be cut to flip and turn the mat. The RED HEATING ELEMENT CAN NOT BE CUT, so be sure to accurately measure the space you are heating.

Programmable Thermostat with Sensor

Honeywell / Aube model # TH115-AF-120S

The programmable floor sensing thermostat with floor sensor is designed to work with electric floor heating systems. It gives you the ability to accurately control the floor temperature for maximum comfort and energy savings. The thermostat features high-tech precision with straight forward, user friendly interface and contemporary design with backlit display. This floor sensing thermostat is digital, programmable, and includes the floor sensor. The thermostat is factory pre-programmed with a 7 day schedule that can be adjusted. This thermostat is 120 volts, rated for 16 amps, easily switching between F and C temperature scales.

THERMOSTAT FEATURES

• AF mode-controls ambient temperature with floor temperature limitation
• A mode controls the ambient air temperature
• F mode controls the floor temperature using an external temperature sensor
• Two temperature sensors-one in floor, one in thermostat for accuracy and security

Installation Monitor

The Installation Monitor can help give you peace of mind while installing the floor warming system. Connect the system leads to the monitor prior to installation. The monitor will "scream" a warning in the event the heating element is cut or damaged allowing you to make any necessary repairs before the heating system is embedded in mortar. If the alarm sounds, stop work and consult the operation manual. We still recommend checking the ohms of the floor heating system with a multimeter before, during, and after installation.

• Red light and alarm indicates lead wires have come loose from the terminals or damage has occurred to the heating system
• A white light indicates the monitor is operating
• Can monitor up to 3 systems at one time when they are temporarily connected in series

ADHESIVE BACKED MAT

This heating mat has double sided tape to offer an adhesive backing that make installation a breeze. Simply fit the mat to your floor, then peal of the tape and adhere to the floor. This greatly reduces the installation time and gets you on your way to enjoying your heated floors.

MADE IN USA

Warming Systems is proudly Made in the USA. Our manufacturing facility and offices are located in Spring Grove, IL (just outside of Chicago). Our systems are made from the highest quality products and offers the best heating technology on the market.

Mat Turns and Fill-in Techniques

• This table contains some of the common turns and techniques used to layout around corners, angles, and built-ins.
• Carefully cut the white mesh to make turns. Never cut, nick, or otherwise damage the heating wire.

Mat Turns and Fill-in Techniques

• This table contains some of the common turns and techniques used to layout around corners, angles, and built-ins.
• Carefully cut the white mesh to make turns. Never cut, nick, or otherwise damage the heating wire.

Mat Turns and Fill-in Techniques

• This table contains some of the common turns and techniques used to layout around corners, angles, and built-ins.
• Carefully cut the white mesh to make turns. Never cut, nick, or otherwise damage the heating wire.

Mat Turns and Fill-in Techniques

• This table contains some of the common turns and techniques used to layout around corners, angles, and built-ins.
• Carefully cut the white mesh to make turns. Never cut, nick, or otherwise damage the heating wire.

Product description

This thermostat automatically energizes the heating cable at temperatures lower than 3°C/38°F, reducing the risk of frozen pipes while saving energy and eliminating the need to unplug cables each spring. It can also be used to control other electrical devices that need to be activated when the temperature approaches the freezing point. The EH38 thermostat is rated at 15 amps with resistive load at 125 Vac, and is UL Listed to US and Canadian Safety Standards.

• Automatically energizes the heating cable at temperatures lower than 3°C/38°F
• Reduces the risk of frozen pipes while saving energy
• May be used to control other electrical devices that need to be activated when the temperature approaches the freezing point
• 15 AMP rating

User questions & answers

Question:	Can I use this with a little space heater in a greenhouse (6'X4') to keep it from freezing at night when I'm starting plants in the winter
Answer:	I don't know why it wouldn't work. I am using it connected to a heating pad on my propane tank regulator to keep it from freezing up. Had it on for 2 months and is working fine. It was 1 degree last night and the heaters and stove worked just fine.
Question:	Is this item a two prong or
Answer:	It is 3 prong so it provides a ground for whatever is plugged into it. It will also take a 2 prong plug, but should be plugged into a grounded outlet, or you can use an adapter.
Question:	I plugged the thermostat into electrical box and the light did not glow. Does the light only come on when the thermostat is activated by temperature
Answer:	I found that when using the plug in thermostat that it does not come on, or turn off at the temperatures stated in the instructions. I comes on at a lower temperature than 38 degrees. When it is on, the light in the thermostat lights up. I think the instructions that come with the unit could be a little clearer. There is no way to adjust the temperature range. I use the thermostat in my RV trailer during the winter to turn on a heat lamp to keep a critical area above freezing. Hope this helps
Question:	Is the power indicater light suppose to come on when unit is plugged in or only when temperature goes below
Answer:	Robert,According to tech support, the indicator light will only come on when power is being supplied to the cable by the thermostat at 38 degrees or less.So in simple terms only when it goes below 38.Hope this helped.Have a great day!Chris B