10 best portable tile saw

Product description

SKIL 3540-02 7" Wet Tile Saw complete tiling projects easily with the model 3540, 7 in. Wet Tile Saw. The stainless steel top resists corrosion and the adjustable rip fence with miter gauge ensures accurate straight and miter cuts. Skil 3540-02 7" Wet Tile Saw features: Stainless steel table top is resistant to corrosion adjustable rip fence with miter gauge for accurate straight and miter cuts 0-45 degree level for a wide range of cuts blade cooling water reservoir to keep blade cool and minimize dust and debris 7" diamond blade for fast and smooth cutting SKIL 3540-02 7" Wet Tile Saw specifications: Amperage: 4.2 Arbor Size: 5/8" Bevel angle range: 0-45 degrees Bevel Stops: 0 Degrees, 45 Degrees Blade Diameter: 7" Depth of Cut at 45 Deg. : 1" Depth of Cut at 90 Deg. : 1-3/8" Length: 14" Name: 3540 (S12) No load RPM: 3600 Voltage: 120V AC only weight (lbs. ): 18 Width: 13.25."

From the Manufacturer

Skil benchtop power tools are quality tools at a great price!

• Corrosive resistant stainless steel top supports tiles up to 12 x 12-inch
• Adjustable rip fence with miter gauge for accurate straight and miter cuts
• Blade cooling water reservoir to keep blade cool while minimizing dust and debris
• Bevel cuts tile from 0 to 45 degrees. Cut material: Stone/Masonry
• Cross cut capacity: 7.75-inch; Diagonal cut capacity: 7.25-inch

User questions & answers

Question:	this saw comes w/a diamond blade. would it be good enough to cut little glass mosaic tiles or should I order a different diamond blade
Answer:	The blade will cut through the glass tiles just fine, however, I would suggest purchasing a thinner more durable blade. I purchased a Ridgid 7" blade from Home Depot. The Ridgid blade make cleaner cuts and wastes less material because it is a thinner blade.Also, Skil just came out with a new updated model of this saw. I would suggest purchasing that saw instead because it has some much needed improvements. Here is some information on the new saw: https://www.skiltools.com/Tools/Pages/ProductDetail.aspx?model=3550-01.
Question:	What is the biggest size of tile this saw can be used for to do diagonal cuts
Answer:	am sure you can cut even 24x24 in. tile. to cut straight get 1x1x 20--24 in, wood and clamp under the table as your guide to cut straight,hope this will help. skil power tools are great and cheaper than MK
Question:	Would this be a good saw to cut rocks in half
Answer:	Depends on the size of the rock. The material is not an issue -- I use it to cut agates and quartz up to a couple inches in size. The important thing is to go slow and make sure to keep the cut wet.
Question:	Will this saw cut peanut brittle? We are currently struggling with the batch we just made and we need to find a good way to cut it
Answer:	i'M SORRY, BUT NO THIS WILL NOT CUT THE BRITTLE. this saw was designed for tile, brick and old tootsie rolls only. the reason tht is, the hamsters in the the motor are allergic to peanuts and a few other foods. seeing as how we all love fluffy hamsters, they gave them work instead of turning them away( that and hamsters have a ton of kids!!). the saw you are looking for has gophers in the drive motor( 2 x's the power for those thick piece's of brittle), that have been thoroughly screened for any deadly allergies to tree nuts and dairy, not to mention sock puppets and shoe polish as well. i do suggest that if you are going to buy the gopher powered brittle slicer 3000xlr made by Skill'dG( skilled gophers), to make sure you are getting the real thing, and not a cheap australian clone. contact the gopher union work force development office and they will give you a list of all non gopher supported and wallaby knock offs and a wallet sized card for easy recognition of their branded products. They may ask for a donation, but it's well worth the $120 to join their non members club. You get free holes in your green, and much, much more. Good luck on your quest, and may the spork be with you.

Product features

Stainless Steel Table Top

A stainless steel top will resist corrosion after multiple uses.

Adjustable Rip Fence with Miter Gauge

The adjustable rip fence with miter gauge will allow you to make accurate and straight miter cuts.

Bevel Cuts Tile

For more intricate designs or to tackle those end pieces, the 0-45 degree bevel will provide flexibility for various cut types.

Blade Cooling Water Reservoir

The constant flow of water keeps blade for overheating and helps minimize dust and debris while cutting tile.

More About This Product

• Amperage: 4.2
• Rating: 120V AC Only
• No Load RPM: 3,600
• Blade Diameter: 7 In.
• Miter Angle: 0-45 Degrees
• Bevel Positive Stop at: 0, 45 Degrees

Product description

PORTER-CABLE PCE980 7 in. Table Top Wet Tile Saw features a powerful 1.0 Horsepower motor providing smooth cutting of porcelain, ceramic and Stone tiles. Cast-metal cutting cart delivers 17 in. Cutting capacity, allowing cutting of 12 in. X 12 in. Tile on a Diagonal. Get accuracy of 1/16 in. On cuts up to 12 in. Long. The Pce980 includes Pce980 7 in. Wet tile saw, 7 in. Porcelain tile blade, Miter square, blade wrench. Includes 3 year limited warranty, 1 year free service contract, and 90 day money back guarantee.

• Onboard miter square to help line up miter cuts and repeatable rip cuts
• Roll cage for easy carrying and protection of the cutting cart
• Splash guard keeps water from spraying the tool operator
• Stainless steel fixed deck holds up to water and jobsite abuse
• Equipped with drain plug to quickly drain water over a bucket without a mess.RPM:2850 rpm

User questions & answers

Question:	how thick will this cut
Answer:	I would say 1:4, if you are cutting porcelain that thick take it slow, natural stone will cut easier. I highly recommend this saw, I use it for small jobs, it’s really great in tight spaces. In my opinion it’s the better of the smaller wet saws as I prefer a rolling table for more accurate cuts. I however use an MK on my bigger jobs and large format tile and stone and it’s a beast with no limitations but cost about 10x what this saw cost. I do a lot of baths and kitchens and I love it!
Question:	Alway problems substituting other brand blades - and can't find PC replacement blades - can anyone confirm good to excellent substitute
Answer:	I've tried several after market blades with this saw. The problem I've experienced is the original PC blade produces a slightly wider cut, allowing the tile to get past the guard support in the back. The blades I've tried produce a thinner cut that prevent the tile from passing around the guard support. I'll try the Pearl P4 7 inch to see if it works, although 50$ is a gamble I'd rather not bet on.
Question:	Can this saw cut glass tiles
Answer:	It can cut glass but without buying a blade specifically for glass tiles you might be disappointed. Every tile installer I know has several different blades always on hand for the abundance of materials thrown at him. Glass Master is a good glass blade and manual cutters often do excellent. With the stock blade you will get some chipping along the cut. Which could be polished out with extra effort. If you can handle chipping go for it.
Question:	Does this saw do miter cuts? Can you angle the blade, or the table
Answer:	Yes, this table saw does simple mitre cuts. The blade is fixed. The table is fixed (does not angle for a compound mitre cut). The product is positioned on the (right) cutting cart that feeds the tile to the blade. The saw comes with a miter square for basic angle cuts.

Product description

7 in. Portable Wet Cutting Tile Saw by USATNM

Product description

This benchtop tile saw is constructed of rigid plastic, metal components, and it comes with a chrome-plated table. Its compact size makes it the ideal tool for the contractor, repairperson and DIYer. The rubber feet help hold the saw in place while cutting tile up to 1-3/16 in. thick. It includes a 7 in. diameter blade at cuts at a maximum 3550 RPM. The Tile Wet Saw features a water reservoir system (to keep the blade wet while cutting), a safety guard over blade, a zero to 45 degree tilting table for beveled cuts, an adjustable rip fence and an angle gauge for miter cuts. This tile wet saw is easy to use and preferred by many.

• Use this tile wet saw to cut through ceramic tile, porcelain tile, marble, slate and stone up to 1-3/16 in. thick
• This handy tile cutting saw includes a water reservoir system to keep the blade cool and lubricated during use
• Features a tilting chrome-plated table that adjusts from zero to 45 degrees for making detailed bevel cuts, an adjustable rip fence and an angle gauge for miter cuts
• Uses 7 in. diameter cutting blades on 5/8 in. arbor and runs at a maximum 3, 550 RPM
• Blade guard is included for safety. Overall width measures 18. 7 in. wide x 15. 9 in. deep

User questions & answers

Question:	What is the max size tile this can handle
Answer:	It uses plain end blades. GREAT machine, can't go wrong, I LOVE mine!!!
Question:	Does this saw include a blade
Answer:	not made in canada,made in china

Product description

Delta 96-014 Folding portable tile saw stand for Delta 7 and 10 inch CRUZER wet saws

• Specifically designed to fit the 7 inch and 10 inch Delta Cruzer tile saws
• One-step set up and fold using the foot actuated pedal
• Designed for quick setup and easy transport
• Lightweight steel tube construction provides a stable work surface

User questions & answers

Question:	Will this work for a Beast Tile Saw 7in or 10in
Answer:	To your first suggestion regarding plywood under your saw, it should work as long as you have it secured with some sort of attachment to the cross bars. However, I am no expert at this so I would highly suggest contacting DeWalt to get their professional opinion.
Question:	Will this hold my mk 101 tile saw
Answer:	We have not tested the D24000 with a Rigid table saw.
Question:	The description says its made of lightweight tubing, what is the weight capacity of this stand
Answer:	It would work on a MK. But designed to be used with a dewalt wet tile saw.
Question:	Will this fit the Ridgid 4092 Tile Saw
Answer:	I do not know. It was for somebody else. Sorry

Product description

Whether you're updating or renovating, adding tile to your kitchen or bathroom is now easier than ever with the SKIL 7-inch Wet Tile Saw (3550). The saw's innovative HydroLock System keeps water splash to a minimum so tiles can be cut in the room where they're being installed. You no longer need to go back and forth to a saw set up in the garage or outside to cut the tiles, so the SKIL tile saw with HydroLock System helps you finish the project faster too The 3550 works with a 7-inch continuous rim diamond blade, which provides efficient and even cutting. It also comes equipped with a durable rust-resistant aluminum table top and a sliding side extension that can be used to support tiles up to 18 x 18-inch.

• Hydro lock water containment system keeps water contained near the blade and reduce clean-up time
• Sliding side extension provides support for tiles up to 18 x 18-inch
• Aluminum table top is a durable, rust-resistant surface
• Adjustable rip fence with miter gauge for accurate straight and miter cuts
• Bevel cuts tile at 0, 22.5 and 45 degrees, giving flexibility for different cut types

User questions & answers

Question:	will this saw, with the standard blade that comes with it, cut glass bottles
Answer:	I don't know for sure. I did cut quite a lot of glass tile. I had to a different blade for glass. it did an exceptional job. In fact i used it to install 2500 sqft of tile in my house. It still has good life left in it.
Question:	Need to slice 1/8"-1/2" glass rods coe 104 & 32. Slice cylinder= thickness of rod & length of 4mm. cut should be clean but not pristine. Will thiswork
Answer:	Thank you for your question. The Skil 3550 is not designed for cutting glass, it is designed for cutting tile. If you have further questions please feel free to contact our Skil Customer Service Representatives at 1-877-754-5999
Question:	Does this include a blade? The info @ Amazon says bare tool, yet the Skil website says yes
Answer:	Yes, the blade is included. The tile saw includes the 7 in. Diamond Blade, Side Extension, Rip Fence, Miter Gauge, Blade Guard and Blade Wrench.
Question:	Why is this model so much more expensive than the model is replaced? The 3540-02 was half this price, so what is the difference
Answer:	Thank you for your question. The Skil 3550 can cut tiles up to 18x18 inches, has an aluminum table top and also our Patent Pending HydroLock System which is an innovated upper and lower guard design that keeps water contained near the blade. The Skil 3540 cuts tile up to 12x12 inches, has a stainless steel table top and does not have the HydroLock System. If you have further questions please feel free to contact our Skil Customer Service Representatives at 1-877-SKIL-999 (1-877-754-5999).

Product features

SKIL 3550-02 7-Inch Wet Tile Saw with HydroLock Water Containment System

Whether you're updating or renovating, adding tile to your kitchen or bathroom is now easier than ever with the SKIL 7-inch Wet Tile Saw (3550). The saw's innovative HydroLock System keeps water splash to a minimum so tiles can be cut in the room where they're being installed. You no longer need to go back and forth to a saw set up in the garage or outside to cut the tiles, so the SKIL tile saw with HydroLock System helps you finish the project faster too! The 3550 works with a 7-inch continuous rim diamond blade, which provides efficient and even cutting. It also comes equipped with a durable rust-resistant aluminum table top and a sliding side extension that can be used to support tiles up to 18 x 18-inch.

Product description

The QEP Wet Tile Saw is ideal on job sites where space prohibits the use of a large wet saw. The 3/5 HP, high-torque motor and included 4 in. continuous rim diamond blade cuts through unlimited sizes of ceramic, marble, slate and stone tile up to 3/4 in. thick. This tile saw even cuts mosaic tile and backsplash tile for DIY projects. The water system not only reduces water runoff, it recycles the water back into the reservoir, minimizing refill frequencies. This dependable wet saw includes dual extension tables to support larger tiles and a hinged cutting table for miter cuts. A 4 in. blade with a 5/8 in. arbor is required. For cutting porcelain and hard tiles, we recommend using the QEP Black Widow Blade, sold separately.

• Easily cuts ceramic, marble, slate and stone tile
• Made from plastic to prevent rust and corrosion
• Portable design makes this wet tile saw easy to transport
• Hinged cutting table is adjustable for making 22.5 degree and 45 degree miter cuts
• Includes 4 in. QEP continuous rim diamond blade, rip guide, angle guide and clip-on extension table

User questions & answers

Question:	Does this machine come already assembled
Answer:	All tapcon screws require the correct size pilot hole be made first. After that depending on the size you may not even need any drill.
Question:	Will this saw cut slate roof tiles
Answer:	Xbox is the drill only . No batteries or kit.
Question:	What is the arbor size on this saw
Answer:	I don't think so, but I have not tried!
Question:	Can you cut a 21in tile
Answer:	It is better to use a hammer drill and special masonry drills for concrete. This drill would do it slowly and might wear out the masonry drill faster.

Product features

QEP 22400Q 3/5 HP Torque Master Tile Saw, 4-Inch

The Torque Master XT Portable Tile Saw is ideal on job sites where space prohibits the use of a large wet saw.

• 3/5 HP, hi-torque geared motor for maximum cutting performance
• Dual extension tables add extra 5" of cutting surface
• Cuts ceramic tile, porcelain tile (for porcelain and hard tiles, we recommend QEP's Black Widow Blade #6-4008BW), marble, slate and stone
• Fully adjustable miter guide with unique ratchet mechanism
• Cutting table is hinged to adjust for making 22.5° and 45°
• Water recirculation system saves time when replenishing water supply and keep work area drier
• Includes 4" QEP Continuous Diamond Rim Blade Black Series (6-4001Q)

• ▶ [Powerful Motor & 6 Variable Speed] - Features a  4.2Amps copper motor for fast cutting and ripping,  making cut wood, plastics, plywood board, PVC pipes, tile with ease. Speed adjustment dial with 6 positions, 3,500-6,500RPM speed range allows you choose the exact speed to deal with different tasks.
• ▶ [Portable Design with 3 Blades] - Compact size and light-weight design makes it a good addition to your toolkit. It is convenient for preservation with the included storage bag. Comes with 1 x 24T TCT for wood cutting,  1x44T HSS for soft metal cutting, 1pcs grit diamond blade for tile cutting.
• ▶ [Precise Cutting & Adjustable Cutting Depth] - Comes with guide rails, achieving straight line cutting easily. Low friction glide strips ensure the mini circular saw glides smoothly over the track. Easy-set depth gauge lever for adjustable cutting depth from 0-22mm (55/64").
• ▶ [Ergonomic & Safe Design] - Soft rubber handle and auxiliary side handle offer more control and less fatigue.Also designed with a dust port and the saw dust pipe, you can connect it to your vacuum to get a clean working environment. The blade can only be pushed out when you press the power switch, safe for use.
• ▶ [Package Contents] -1 x Mini Circular Saw, 1 x 24T TCT Blade, 1 x 44T HSS Blade, 1 x Diamond Blade, 2 x 15" Guide Rails, 1 x Hex Wrench, 1 x Scale Ruler, 1 x Dust Exhaust Pipe, 1 x User Manual and a Storage Bag for easy carrying.

Product description

This 700XT Tile Wet Saw is equipped with unique side extension table to support large format tiles Features. Easily cuts tile up to 1 25 in thick. Compact and portable with builtin handle. Make rip and diagonal cuts on any size tile. Powerful 34 Peak HP motor for cutting ceramic marble stone travertine and porcelain for porcelain and hard tiles we recommend QEPs Black Widow Blade 67008BW. Water recirculation channel. Lockdown rip guide for fast multiple cuts. Nonslip feet for stability. 225 and 45 angle guide for diagonal cutting. Extension side table. Deep water tray means no refillingSpecifications. Motor 34 HP 120V60Hz 48 Amps. Watts 550W. RPM 3600. Blade Capacity 7. Arbor 58. Depth of Cut 114 Thick Tile. Dimension 988 H x 1574 W x 2008 L. Weight 1905 lbs

• Easily cuts tile up to 1- .25 in. thick
• Compact and portable with built-in handle
• Make rip and diagonal cuts on any size tile
• Powerful 3/4 Peak HP motor for cutting ceramic, marble, stone, travertine and porcelain
• Water recirculation channel

User questions & answers

Question:	Will this cut 12x24” tile
Answer:	yes
Question:	is the dimond disc in the box is well
Answer:	This nail gun uses 18 gauge nails from ¾ in. to 2 in. length. It is the perfect tool for finishing type applications such as installing molding, trim, and shop projects.
Question:	Will this cut 24x24tile
Answer:	Comes with a tool case
Question:	will there be lots of water / sludge splash around the saw
Answer:	There is a version of the charger that will accept 220v. You need to keep looking... I had one in Thailand.

Product description

The FLEX CS 40 wet tile saw is made for use in the stone, tile and glass industries. The powerful 12-amp motor makes it possible for the saw to cut through any tough material. The wet tile cutter is also equipped with a high quality water-feed system that will eliminate the harmful dust particles which are common in dry cutting applications. Includes a side handle for more stability and the CS 40 has the ability to accept a curved cutting blade thus making curve cutting operations safer and easier.

• Blade Size - 5" x 7/8' with 20mm adapter ring
• Tilting range of 0 - 45 degrees
• Max cutting thickness at 90 degrees - 1.6"
• Blade not included
• Powerful 12 amp motor with a no load speed of 12,000 RPM

User questions & answers

Question:	where made it? how long warranty
Answer:	Yes it does. It has a buit in shut off on the connector so unsnapping it will shut the water from the hose too.
Question:	Does it come with a carry case
Answer:	Charges a DCB606 FLEX VOLT battery in 60 minutes. DCB609 will take slightly longer.
Question:	Can you adjust this a saw or guide to cut miters
Answer:	The DCS690X2 is manufactured in China.
Question:	What is the max cut width using the built in guide/fence
Answer:	Yes, it was compatible with my old Makita angle grinder