13 best delta contractor table saws

Product description

For over 100 years Delta has been meeting the needs of the most exacting Craftsmen. The Delta 36-6013 Portable 10 inch contractor table saw was designed with the professional in mind. Powered by a 15 amp motor it is maximized for precision, durability, and mobility. The heavy duty one piece rail system, along with the newly designed fence system allows for precision cuts every time. The fence incorporates a special design allowing you to cut narrow pieces of stock. The saw has a large 25 inch rip capacity 3-1/2 inch depth of cut at 90 degrees and 2-1/2 inch at 45 degrees. A 2. 5 inch dust collection port easily connects to a vacuum for efficient dust extraction to your work area clean. Cut after cut, this saw is designed for the demands of the professional user and serious craftsman and Delta backs that up with its 5-year pledge to you.

• Powerful 15 Amp Contractor Grade motor easily handles treated lumber and hardwoods
• 25 Inch Rip Capacity handles large stock and 13/16 in. X 8 in. STACKED DADO CAPACITY
• Heavy Duty Fence Construction with quick position tabs
• Professional Grade 5-Year

User questions & answers

Question:	dado blade compatible
Answer:	I would say yes but it’s an educated guess
Question:	Is there a base stand available for it
Answer:	I had to enlarge the opening a bit to install the new switch. The saw case is plastic and it's easy to modify the opening with a hacksaw - the kind with a small bayonet type handle for use in tight spaces. The plastic case is very easy to cut through. Got the switch installed and everything works just like it's supposed to.
Question:	Does this saw come with an extension
Answer:	Any time you are replacing a wired item, you should be removing one wire at a time from the old item and placing it on the new one. If you didn't think to do that, it's still not the end of the world. Looking at the switch from the backside, the black wires connect to the left side terminals and the white wires go to the right side. If you're still confused, here's a link to the wiring diagram: http://keyboard-keys.info/ryobi-table-saw-wiring-diagram
Question:	Is this belt drive or direct drive
Answer:	This switch has power for the main circuit and two side circuits. In the intended design they power the light and Lazer. If your tool is set up this way then it should work.

Product features

HUGE RIP CAPACITY

The Delta 36-6013 houses a powerful 15 amp motor and boosts an enormous 25 inch rip capacity. Its 559 square inch table surface and tube steel frame provides you the stability needs for those large cuts. This is an excellent saw for the Professional Flooring Contractor.

THE PRECISION YOU DEMAND

The Delta 36-6013 features a telescoping rails system make fence adjustments fast, smooth, and accurate. The rails utilize 3 quick adjustment tabs that allow you to quickly relocate the fence while ensuring the blade and fence are always parallel guaranteeing consistent and true cuts.

Product description

For over 100 years Delta has been meeting the needs of the most exacting Craftsmen. The Delta 36-5052 10” contractor table saw was designed with the professional in mind. Powered by a 15 amp induction motor it is maximized for precision, durability, stability, and mobility. The heavy duty one piece rail system, along with the Legendary Biesemeyer style fence system allows for precision cuts every time and has a special designed allowing you to cut small pieces of stock. The saw has a large 52 inch rip capacity, 3-1/8 inch depth of cut at 90 degrees and 2-1/4 inch at 45 degrees. A 2. 5-inch dust collection port easily connects to a vacuum for efficient dust extraction to your work area clean. This is a BELT DRIVEN machine that offers low vibration and easy tensioning. A unique tubular stand with two fixed wheels and one swivel wheel makes the saw very stable and easy to move. Cut after cut, this saw is designed for the demands of the professional user and serious craftsman and Delta backs that up with its 5-year pledge to you.

• IF ANY COMPONENT IS MISSING FROM YOUR ORDER PLEASE ACCEPT THE SHIPMENT AND CONTACT AMAZON. DO NOT RETURN THE ENTIRE UNIT BECAUSE OF A MISSING PART. WE WILL EXPIDITE THE DELIVERY OF ANY MISSING COMPONENT. THANK YOU
• THIS ITEM SHIPS IN 3 BOXES. YOU SHOULD RECEIVE THE FOLLOWING COMPONENTS - 36-5 Saw Body, 36-T52 52" Rails , 36-T53, Extension Table
• Powerful 15 amp Contractor Grade motor easily handles hardwoods
• 52 Inch Rip Capacity handles large stock
• Smooth and dependable adjustable belt drive table saw
• Legendary Biesmeyer Fence Accurate to 1/64”
• 13/16 in. X 8 in. STACKED DADO CAPACITY

Product features

MEETING THE NEEDS OF FINE CRAFTSMAN

For over 100 years Delta has been meeting the needs of the most exacting Craftsmen. The Delta 36-5000 Series Contractor Table Saw is designed with the perfectionist in mind! Try this legendary brand and let us exceed your expectations. We are confident that you will lover the results that this machine will help you achieve. The Delta 5000 Series Table Saw is the perfect choice for the fine craftsman.

BUILT-TO-LAST

The Delta 5000 Series 10” contractor table saw was designed with the professional in mind. Powered by a 2.9 HP 15 amp induction motor easily powers through lumber and hardwood. The adjustable belt drive system reduces vibration and improves motor life

ACCURACY

The heavy duty rail system, along with the Legendary Biesemeyer style fence system allows for precision cuts every time and the fence has a special design allowing you to cut small pieces of stock. When precision matters you can count on Delta for accurate and repeatably consistent cuts.

BIG CAPACITY

The cast iron table combined with your choice of cast iron or steel extension wings give this saw has an enormous 52 inch rip capacity, The Delta 5000 series saws provide a 3-1/8 inch depth of cut at 90 degrees and 2-1/4 inch cutting depth at 45 degrees.

Product description

A complete fence and rail system for upgrading your current table saw to BIESEMEYER grade fence. Fence height- 2-1/2 inches. Maximum rips to right of blade- 30 inches.

• One piece square tubular rail. Max Rip to Left of Blade-13-1/2 inch. Length: Fence 37 inch, Rail 57-1/2 inch
• Mounting design attaches to Delta table saws including Contractor Saw , Hybrid Saw , and Unisaw models
• Three-point locking system with twin hairline pointers to assure fence is parallel to blade and accurate to within 1/64 of an inch (0. 4mm)
• Easy-gliding, steel tube fence body to handle Quick, precision ripping, and square cuts
• Fence securely clamps to front tube and hooks over rear rail to allow for fence attachments

User questions & answers

Question:	Can this be adapted for a 26" deep delta model ts200ls
Answer:	You would need to fabricate a 1" filler strip to bridge the back rail to the back of the table.
Question:	Would this fit on my Delta
Answer:	If your saw has a top that measures 27” deep yes. You may have to drill a few holes to match your top.
Question:	I have a 10” belt drive table saw, craftsmen, 113.298843 would i be able to hook this up? sounds like i would need to re drill some holes and such
Answer:	I installed this unit on a 113 series craftsmen saw with 27 inch cast iron table extensions. Some holes on the delta fence will line up with existing holes on the original saw the rest I drilled by hand, wasn't to hard as the cast iron is soft compared to steel. I did needed to shim .002 on the rear fence guide because the extensions were shorter then the actual table. I am very happy with the finished project. The new fence is dead accurate every time.
Question:	What is the width of cut to the right and to the left of the blade? Also, does it have English measurements on the guide bar tape
Answer:	30” to the right of the blade and the tale gives you a measurement of 16” to the left of the blade. It has measurements in inches.

Product features

Sturdy and Secure

The DELTA T3 Fence System is an one piece square tubular rail with a mounting design that attaches to Delta table saws including Contractor Saw, Hybrid Saw and other Unisaw models. This fence system comes with a three-point locking system with twin hairline pointers that assure you that the fence is parallel to blade. With various features such as easy-gliding, steel tube fence body to handle Quick, precision ripping and square cuts, the DELTA T3 Fence System is ideal for fence attachments.

Product description

The Powermatic 64B Table Saw, with left tilt arbor, offers 1-3/4 horsepower in dual voltage to meet the demands of the professional contractor. The transparent blade guard has independent leaves, and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts. An arbor lock is accessed from above the table, eliminating the need for dual blade wrenches. The T-slot miter gauge has rack-and-pinion angle setting, positive stops and extension plate for expanded workpiece support.



The Powermatic 64B has cast iron table and wings with front edge bevel, and the working area is further expanded by the melamine-surfaced wood extension table. The exclusive Accu-Fence® system is available in 30” or 50” rip cut capacity. Storage hooks on the stand keep your accessories within reach.

From the Manufacturer

The 64B table saw, with left tilt arbor, offers 1-3/4 horsepower in dual voltage to meet the demands of the professional contractor. The transparent blade guard has independent leaves, and the quick release riving knife reduces chance of kickback. A low profile riving knife is included for non-through cuts. An arbor lock is accessed from above the table, eliminating the need for dual blade wrenches. The T-slot miter gauge has rack-and-pinion angle setting, positive stops, and extension plate for expanded workpiece support. The 64B has cast iron table and wings with front edge bevel, and the working area is further expanded by the melamine-surfaced wood extension table. The exclusive Accu-Fence® system is available in 30? or 50? rip cut capacity. Storage hooks on the stand keep your accessories within reach.

• EXCLUSIVE ACCU-FENCE SYSTEM: Locks to rail without play for increased safety and precision.
• QUICK-RELEASE RIVING KNIFE: Maintains close blade proximity to reduce chance of kickback.
• CAST IRON TRUNNION: Ensures smooth blade positioning.
• MICRO-ADJUST MITER GAUGE: Offers wider crosscut support.
• BUILT-IN DUST PORT: Increases dust collection efficiency.

User questions & answers

Question:	Is the boxed saw unit in one piece? Can it be removed in pieces for transporting from the pallet to the basement
Answer:	It’s in a few pieces, but the only way you’d get it into a basement is if you have four huge men to lift it. Otherwise- no.
Question:	How many hp are available when plugged in 110v. can it work with 220v 2 phase? if so, how many hp is available this way
Answer:	The saw I have is the Powermatic PM 1000 Table Saw 1.75HP, 1 PH @ 115V. Apparently it can be be rewired for 230V, with a 7A draw. I don't know the resulting HP. Tried to look it up just now, but couldn't satisfy myself that I was getting the right answer due to unknown variables about the motor. I run mine at 115V.
Question:	Is it a left tilting blade
Answer:	yes, the top of the blade goes left
Question:	Can I plug this into any standard outlet
Answer:	Yes, you can plug it into any standard 120v outlet.

Product description

For a cleaner home, ship and cleaner air; the Miles craft Dust Cutter cuts dust by over 90%

• Nylon
• Quick and easy installation
• Never needs removing to empty
• Fits many different table saws (having base dimensions up to 20" wide and 17" deep)
• Optional and easy vacuum connection
• Comes in 3 modes: collector, funnel and vacuum

User questions & answers

Question:	Will it fit a skil 3410-02 10-inch table saw with folding stand
Answer:	Go to a camping source like Campers World and search for black or grey water flush out valves for the holding tanks. Should find a solution there for somewhat low cost.
Question:	How tall is it? As in from the bottom where the opening is to the top where it attaches to the stand/saw
Answer:	I didn't hook them up to 4inch. I ran 2 3/4 flex and pvc. Btw...it clogs up with saw dust. I drilled a hole on side opposite the slide with a forsner bit to blow it out. I cover the hole with duct tape.
Question:	How does it attach to the table saw base? Velcro
Answer:	No, They are 3 11/16 id and 3 13/16 + 1/32 od. There is nothing 4" here.
Question:	Does it include the adapter to use with 2 1/2” dust collection
Answer:	I used 4" schedule 40 PVC and it fit snugly on the 4" blast gate. I also drilled and screwed two sheet metal screws per blast gate (along with silicon sealer)

Product features

Milescraft 1500 DustCutter

The Milescraft DustCutter will keep the air in your shop and home cleaner! Table saw dust collector cuts by over 90%. For a cleaner home, shop and cleaner air. Use your saw indoors or out. The DustCutter fits most table saws having base dimensions up to 20 in. W and 17 in. D and will connect to vacuum hoses of 1-1/4 in. and 2-1/2 in.

Collector Mode

After using the saw, empty dust into a receptacle by unzipping the bottom of the DustCutter. Bag capacity is 3 cubic feet.

Funnel Mode

Continuously empty dust by unzipping the bottom of the DustCutter, allowing dust to funnel into a receptacle

Vacuum Mode

Attach a 1-1/4″ or 2-1/2″ vacuum hose to the DustCutter and suck it out of the bag and air while operating the table saw

Product description

For over 100 years Delta has been meeting the needs of the most exacting Craftsmen. The Delta 36-6023 Portable 10 inch contractor table saw was designed with the professional in mind. Powered by a 15 amp motor it is maximized for precision, durability, and mobility. The heavy duty one piece rail system, along with the newly designed fence system allows for precision cuts every time. The fence incorporates a special design allowing you to cut narrow pieces of stock. The saw has a large 25 inch rip capacity 3-1/2 inch depth of cut at 90 degrees and 2-1/2 inch at 45 degrees. A 2. 5 inch dust collection port easily connects to a vacuum for efficient dust extraction to your work area clean. Cut after cut, this saw is designed for the demands of the professional user and serious craftsman and Delta backs that up with its 5-year pledge to you.

• Powerful 15 Amp Contractor Grade motor easily handles treated lumber and hardwoods
• 32. 5 Inch Rip Capacity handles large stock and 13/16 in. X 8 in. STACKED DADO CAPACITY
• Durable rack and pinion fence rails make fence adjustments fast, smooth, and accurate
• Professional Grade 5-Year Warranty

User questions & answers

Question:	does this have metal gears? And is it a wormgear
Answer:	For moving the fence and putting the blade on an angle yes it does but some of the levers are really hard dense plastic
Question:	Where’s it made
Answer:	Taiwan
Question:	how high this table saw is with the stand
Answer:	The table is about 36" off the floor when it is on the stand.
Question:	Can you separate the stand from the saw
Answer:	It comes in the box separate. If you don't want to use the stand ... you could set it in/on a table.

Product features

THE ULTIMATE IN PORTABLE TABLE SAWS

HUGE RIP CAPACITY

The Delta 36-6023 houses a powerful 15 amp motor and boosts an enormous 32.5 inch rip capacity. Its 559 square inch table surface, tube steel frame and Delta patented one step folding stand provides you the stability needs for those large cuts.

THE PRECISION YOU DEMAND

The Delta 36-6023 features a rack and pinion fence rails make fence adjustments fast, smooth, and accurate. The rails utilize 3 quick adjustment tabs that allow you to quickly relocate the fence while ensuring the blade and fence are always parallel guaranteeing consistent and true cuts.

Product description

For over 100 years Delta has been meeting the needs of the most exacting Craftsmen. The Delta 36-5100 10” contractor table saw was designed with the professional in mind. Powered by a 15 amp induction motor this saw is maximized for precision, durability, stability, and mobility. The heavy duty one piece rail system, along with the Legendary Biesemeyer style fence system allows for precision cuts every time. The fence incorporates a special design allowing you to cut narrow pieces of stock. The saw has a large 30 inch rip capacity 3-1/8 inch depth of cut at 90 degrees and 2-1/4 inch at 45 degrees. A 2. 5 inch dust collection port easily connects to a vacuum for efficient dust extraction to your work area clean. This is a BELT DRIVEN machine that offers low vibration and easy tensioning. A unique tubular stand with two fixed wheels and one swivel wheel makes the saw very stable and easy to move. Cut after cut, this saw is designed for the demands of the professional user and serious craftsman and Delta backs that up with its 5-year pledge to you.

• IF ANY COMPONENT IS MISSING FROM YOUR ORDER PLEASE ACCEPT THE SHIPMENT AND CONTACT AMAZON. DO NOT RETURN THE ENTIRE UNIT BECAUSE OF A MISSING PART. WE WILL EXPIDITE THE DELIVERY OF ANY MISSING COMPONENT. THANK YOU
• THIS ITEM SHIPS IN 2 BOXES. YOU SHOULD RECEIVE THE FOLLOWING COMPONENTS - 36-5100 Tables Saw Body 36-T31 30" Rails
• Powerful 15 Amp Contractor Grade motor easily handles hardwoods
• 30 Inch Rip Capacity handles large stock and 13/16 in. X 8 in. STACKED DADO CAPACITY
• Legendary Biesmeyer Fence Accurate to 1/64”
• Smooth and dependable adjustable belt drive table saw
• 13/16 in. X 8 in. STACKED DADO CAPACITY

User questions & answers

Question:	How long does shipping take
Answer:	Feb 1, 2021: I ordered mine on Jan 20, 2021. It is scheduled for delivery on Feb 8th even though it is sitting 50 miles from me now(it's Feb 1, today) . I don't understand that but I can be patient......really, REALLY, REALLY I CAN......who hoo, bah bah yippie wa hoo @*^!(%*#!!....... i can, i will, sighhhhh. Edit Feb 8, 2021: Saw arrived today as planed!! NO RAILS.... (!^E!@#&!! Just spent an hour on the phone with Conner in "Heavy shipping department. He was able to order them through Amazon to be here Feb 10, 2021. We will see. Have fingers crossed. Oh, I am in Nashville, Tn.
Question:	This order should be two packages (one for main unit, one for rail system) but only one box arrived. Anyone else have same problem
Answer:	Mine arrived in one very heavy box (300lbs) plus one tube containing the side rails. Both arrived at the same time.
Question:	Where is this product made
Answer:	Can't answer again 100%. But I did not see anything that indicated it was made outside the US. The instructional papers did not have those awkward wordings you get from non English speaking countries.
Question:	Does this come with a combination or rip blade blade
Answer:	it comes with a combination blade

Product features

MEETING THE NEEDS OF FINE CRAFTSMAN

For over 100 years Delta has been meeting the needs of the most exacting Craftsmen. The Delta 36-5000 Series Contractor Table Saw is designed with the perfectionist in mind! Try this legendary brand and let us exceed your expectations. We are confident that you will lover the results that this machine will help you achieve. The Delta 5000 Series Table Saw is the perfect choice for the fine craftsman.

BUILT-TO-LAST

The Delta 5000 Series 10” contractor table saw was designed with the professional in mind. Powered by a 15 amp induction motor easily powers through lumber and hardwood. The adjustable belt drive system reduces vibration and improves motor life

PRECISION

The heavy duty rail system, along with the Legendary Biesemeyer style fence system allows for precision cuts every time and the fence has a special design allowing you to cut small pieces of stock. When precision matters you can count on Delta for accurate and repeatably consistent cuts.

BIG CAPACITY

The cast iron table combined with your choice of cast iron or steel extension wings give this saw has an enormous 30 inch rip capacity, The Delta 5000 series saws provide a 3-1/8 inch depth of cut at 90 degrees and 2-1/4 inch cutting depth at 45 degrees.

Product description

For over 100 years Delta has been meeting the needs of the most exacting Craftsmen. The Delta 36-5000 10” contractor table saw was designed with the professional in mind. Powered by a 15 amp induction motor it is maximized for precision, durability, stability, and mobility. The heavy duty one piece rail system, along with the Legendary Biesemeyer style fence system allows for precision cuts every time. The fence incorporates a special design allowing you to cut narrow pieces of stock. The saw has a large 30 inch rip capacity 3-1/8 inch depth of cut at 90 degrees and 2-1/4 inch at 45 degrees. A 2. 5 inch dust collection port easily connects to a vacuum for efficient dust extraction to your work area clean. This is a BELT DRIVEN machine that offers low vibration and easy tensioning. A unique tubular stand with two fixed wheels and one swivel wheel makes the saw very stable and easy to move. Cut after cut, this saw is designed for the demands of the professional user and serious craftsman and Delta backs that up with its 5-year pledge to you.

• IF ANY COMPONENT IS MISSING FROM YOUR ORDER PLEASE ACCEPT THE SHIPMENT AND CONTACT AMAZON. DO NOT RETURN THE ENTIRE UNIT BECAUSE OF A MISSING PART. WE WILL EXPIDITE THE DELIVERY OF ANY MISSING COMPONENT. THANK YOU
• THIS ITEM SHIPS IN 2 BOXES. YOU SHOULD RECEIVE THE FOLLOWING COMPONENTS - 36-5000 Tables Saw Body 36-T31 30" Rails
• Powerful 15 amp Contractor Grade motor easily handles hardwoods
• 30 Inch Rip Capacity handles large stock and 13/16 in. X 8 in. STACKED DADO CAPACITY
• Legendary Biesmeyer Fence Accurate to 1/64”
• Smooth and dependable adjustable belt drive table saw
• 13/16 in. X 8 in. STACKED DADO CAPACITY

User questions & answers

Question:	What’s the difference between this and the 36 - 5100 T2 , I purchased tha one and it cost $150 more
Answer:	the only difference is cast iron wing vs steel wings.
Question:	Do you have parts for delta table saw model 36-979 part number sw
Answer:	My saw was missing parts so I returned the saw.
Question:	What are the difference between the 36-5000t2 and 36-725t2 table saw
Answer:	Never received the saw after lengthy wait and many phone calls.

Product features

MEETING THE NEEDS OF FINE CRAFTSMAN

For over 100 years Delta has been meeting the needs of the most exacting Craftsmen. The Delta 36-5000 Series Contractor Table Saw is designed with the perfectionist in mind! Try this legendary brand and let us exceed your expectations. We are confident that you will lover the results that this machine will help you achieve. The Delta 5000 Series Table Saw is the perfect choice for the fine craftsman.

BUILT-TO-LAST

The Delta 5000 Series 10” contractor table saw was designed with the professional in mind. Powered by a 15 amp induction motor easily powers through lumber and hardwood. The adjustable belt drive system reduces vibration and improves motor life

PRECISION

The heavy duty rail system, along with the Legendary Biesemeyer style fence system allows for precision cuts every time and the fence has a special design allowing you to cut small pieces of stock. When precision matters you can count on Delta for accurate and repeatably consistent cuts.

BIG CAPACITY

The cast iron table combined with your choice of cast iron or steel extension wings give this saw has an enormous 30 inch rip capacity, The Delta 5000 series saws provide a 3-1/8 inch depth of cut at 90 degrees and 2-1/4 inch cutting depth at 45 degrees.

Product description

The Delta 36-L336 10-inch 3HP left-tilt Unisaw with its 36-Inch BIESEMEYER fence system has a powerful 5 horsepower, 220 volt, 60 Hz American Marathon motor designed to handle the most demanding production environments. The saw comes standard with Delta’s legendary Biesmeyer fence system and is backed by Delta’s 5 YEAR professional . Dual front cranks make adjusting blade height and bevel easy, accurate, and repeatable. The forward located bevel dial allows fine tuning of the blade bevel to an accuracy you can trust to be within 1/4 degree. A single-cast TRUNNION system results in incredible vibration control providing continuous smooth operation. The riving knife enables tool-less adjustment for through- and non-through cuts including grooves for shelves and picture frames as well as dadoes, rabbets, and cheek cuts for furniture. Other features include a push button Arbor lock making the blade changing process with the use of only one wrench. Improved table-top geometry provides more surface area to stabilize the product and offers outstanding smoothness. A large cast iron cabinet base provides added stability. Storage under the table board is convenient and expandable and the Bi-level dust extraction improves dust collection. This saw is ideal for woodworking, cabinet making, and boat building.

From the Manufacturer

Delta’s 36-L336 left tilt cabinet saw is ideal for woodworking, cabinet making, and boat building. It features up-front dual-crank controls with locking cams, speedometer style scales and a 36 inch Biesemeyer fence. The 3 HP 230V motor cuts hardwoods and engineered products like MDF and melamine. The riving knife enables tool-less adjustment for through- and non-through cuts including grooves for shelves and picture frames as well as dadoes, rabbets, and cheek cuts for furniture. The single-cast trunion provides increased vibration control. Largest throat plate in category eases blade changes. Storage under the table board is convenient and expandable. Bi-level dust extraction improves dust collection.

• THIS ITEM SHIPS IN 4 BOXES. YOU SHOULD RECEIVE THE FOLLOWING COMPONENTS - 36-L300 3hp Saw Body (Crated) 78-138 Fence Rails (Boxed) 78-919 Fence & Legs (Boxed) 78-864 Extension Table (Boxed)
• IF ANY COMPONENT IS MISSING FROM YOUR ORDER PLEASE ACCEPT THE SHIPMENT AND CONTACT AMAZON. DO NOT RETURN THE ENTIRE UNIT BECAUSE OF A MISSING PART. WE WILL EXPIDITE THE DELIVERY OF ANY MISSING COMPONENT. THANK YOU
• Powerful 3 horsepower, 220 volt, 60 Hz American Marathon motor designed to handle the most demanding production environments.
• Unrivaled vibration control, for smooth operatIon and accuracy
• Bevel dial tunes blade bevel providing accuracy to within 1/4°
• Legendary Biesemeyer fence system allows for precision cuts every time and has a special designed allowing you to cut small pieces of stock
• A single-cast TRUNNION system results in incredible vibration control providing continuous smooth operation

User questions & answers

Question:	How does this saw compare to a Powermatic in regards to price vs. quality
Answer:	That would be hard for me to say since I previously owned a Powermatic 66 and it looks like the PM 2000 has replaced that model of which I am not familiar with. I liked my Powermatic 66 very much . It was better than the the older Delta Unisaws IMO. Having said that I liked my new Unisaw so much that I sold my Powermatic 66. I've had this newer Unisaw since 2012 but it has seen only light use since it was more of a back up saw for my MiniMax panel saw. I just sold that, so I will now be using my Unisaw exclusively. I don't think you'll find the same upgraded features on the Powermatic 2000 as those found on the Unisaw and if not then I believe the extra cost is worth it !
Question:	Is there an optional toe-kick "OFF" button available or space available at the bottom to add one
Answer:	I agree, there are foot switches available and plenty of space to put one on the floor...but no real toe space under the saw. I think a floor switch would get in the way of your feet when using the saw, or any cabinet saw. The large thigh-activated off switch performs a very good safety action. A contractor's saw on a base with open legs could give you a spot to put a foot switch, but why have a cabinet saw unless you want the cabinet and all of its benefits?
Question:	where is it made? USA
Answer:	NO , at the begining they were made in usa , but like everything else its now made over seas in taiwan , powermatic , sawstop all followed production overseas ... shame :(
Question:	I see that the Saw comes in 3 boxes ... what is the approximate weight of these boxes? I would need to getthe back to a walk-in basement. Thx
Answer:	The main box or crate (containing the saw, extension tables and some other small parts) is 500 lbs. The other 3 boxes (the rails, the wooden extension table and the box containing the fence and ext. table legs) are approx. 50-60 lbs. each.

Product description

The Delta 438010170206S Rocker Switch has terminals. This authentic replacement part is compatible with Delta Drum Sanders, Table Saws, Jointers, Saws, Lathes and other tools, including model numbers: 36-670 Type-1, 22-580 Type-1, 28-231 Type-1, 28-254 Type-1, 28-255 Type-1, 28-269 Type-1, 28-270 Type-1, 28-293 Type-1, 28-299 Type-1, 31-250 Type-1, 31-250 Type-2, 31-250 Type-3, 31-252 Type-1, 31-255X Type-1, 31-255X Type-2, 31-300 Type-1, 33-830 Type-2, 33-830 Type-1, 33-990 Type-1, 34-444 Type-4, 34-445 Type-4, 34-474 Type-1, 36-426 Type-1, 36-430 Type-1, 36-431 Type-1, 36-440 Type-1, 36-441 Type-1, 36-441B Type-1, 36-444 Type-1, 36-445 Type-1, 36-450 Type-1, 36-451X Type-1, 36-454 Type-1, 36-455 Type-1, 36-465 Type-2, 36-465 Type-1, 36-470 Type-1, 36-474 Type-1, 36-475 Type-1, 36-477 Type-1, 36-490 Type-1, 36-505X Type-1, 36-507X Type-1, 36-550 Type-2, 36-550 Type-1, 36-560 Type-1, 36-630 Type-1, 36-635 Type-1, 36-640 Type-1, 36-649 Type-1, 36-650 Type-2, 36-650 Type-1, 36-675 Type-1, 36-678 Type-1, 36-679 Type-1, 36-680 Type-1, 36-680XL Type-1, 36-681 Type-1, 36-681XL Type-1, 36-682 Type-1, 36-682XL Type-1, 36-977 Type-1, 36-978 Type-1, 36-980 Type-1, 36-981 Type-1, 36-982 Type-1, 37-195 Type-2, 37-195 Type-1, 37-196 Type-1, 37-380 Type-1, 37-380 Type-2, 37-866 Type-1, 37-866X Type-1, 37-877 Type-2, 37-877 Type-1, 46-745 Type-1, 46-746 Type-1, 46-756 Type-1, 36-480 Type-1, 36-485 Type-1, TS220LS Type-1, 36-977, 36-978, 36-979, 36-980, 36-981, 36-982, 46-755X, 37-275X, 46-765X Type-1, 52-858 Type-1, 52-866 Type-1, RS830 Type-1. This part weighs 0.05-pounds. After nearly 90-years of expertise in the woodworking business, Delta Power Equipment Corporation has become one of the most revered brands in woodworking tools today.

• Authentic Delta replacement rocker switch
• Has terminals
• Fits several models of Drum Sanders, Table Saws, Jointers, Saws, Lathes and other tools
• Standard duty replacement part
• Built strong for longer life

User questions & answers

Question:	I have a Delta 34-474 table saw. Does this switch work with 240v power
Answer:	The Delta 34-474 was intended for use in the United States and Canada. It does not work with 240v power.
Question:	Are there instructions for replacing the switch? Is it difficult to do
Answer:	If you can raplace a wall outlet or switch a switch then you can perform this simple wiring task. Just pay attention to the wire colors and locations. Wire in the same way the old came out.

• MEASURE YOUR FACTORY INSERT AND COMPARE SIZE BEFORE YOU ORDER. Zero Clearance inserts are table saw specific. Since every table saw brand and manufacturer is different, we recommend that you measure the exact length, width and thickness of your table saw insert or opening and compare it to the size we list. Also be aware of the shape of your current insert of whether its round, square ends or if there are any indents or protruding notches. Insert colors may vary from images shown.
• If you own a table saw, then you probably have had smaller pieces of wood get caught between the saw blade and the factory supplied throat plate opening. This can cause that piece of wood to jam up against the blade and go flying across the room or worse yet, right back at you. Zero clearances help minimize this situation from happening since there is no gap between the blade and the zero clearance opening. The opening is more like a custom slot cut to the exact width of your table saw blade.
• Another great reason to use a zero clearance insert is to help reduce that pesky and irritating tear out you always tend to get on your cuts. Without a zero clearance, the wood has no support by the blade to prevent the wood from tearing out. This is especially true when cutting plywood. Zero clearance inserts help prevent tear out by essentially enveloping the blade on all sides which doesn’t allow the wood to tear out since there is not gap between the blade and insert.
• Zero Clearance inserts can be used in conjunction with most any table saw blade including thin kerf, standard kerf and carbide tipped blades. You can also use zero clearance inserts with dado blade sets. The reason you would use zero clearance inserts with dado blades is to reduce the amount of tear out the dado blade set produces. We recommend that you use separate zero clearance inserts for dado blades since the gap for dados will be much wider than standard width table saw blades.
• This zero clearance insert is made from a high density phenolic material that was chosen for its ability to stand up to everyday workshop use. The insert features two Snug Fit sand-able side tabs that allow you to remove a little material at a time for a perfect fit if necessary. The insert also features a top and a side Snug Fit Screw for a tight fit to you saw with no movement!

User questions & answers

Question:	Will this fit a Craftsman 103.2000, 9" table saw
Answer:	No it won’t
Question:	Will this fit a grizzly 1022Z table saw
Answer:	I purchased several for my G1022. I just had to slightly modify the fit with a hand file and sander.
Question:	Will this fit an older Rockwell/Delta model
Answer:	This is made to fit the Delta Uni-saw and Delta's contractor saws (New & Old) along with the other table saws listed in the description. I have a old Delta Uni-saw with a Ser.# that dates back to 1942 that I had refurbished I had no problem fitting it to my saw lots of adjustments UP and Down Side to Side to get a tight fit no major gaps it may not be an original part, but it very close. Hope that helps
Question:	will phenolic material hold up if edge is reduced to 1/8 inch thick? My older Delta tabel saw throat plate rests on a 1/8" lip
Answer:	I have the same 1/8th inch lip on my Delta 36-600 that would need the same solution. Does someone know what zero clearance blank I could use that will either fit the saw or allow for an edge rabbet transition around the perimeter?

Product features

Eliminate The Gap From Factory Inserts

Many of us who own table saws know all too well what happens when a small, thin piece of wood gets stuck or wedged between the blade and the opening on a factory supplied throat plate insert. The end result can be a visit to the hospital or even worse. Zero clearance inserts help minimize the chances of this happening by eliminating the gap that would normally surround your table saw blade. By doing this, the zero clearance won't allow for a small but dangerous piece of wood to get wedged in the factory plate and possibly kick-back at you.

High Quality Construction and Materials

This zero clearance insert is made from high quality phenolic material. We chose this material because of its superior rigidity, flatness, durability, low friction and its ability to last a very long time even after repeated daily use. Another reason we chose phenolic is that it can also be shaped to exacting specifications without breaking down like other materials used to make zero clearances can. This is one of the densest, longest lasting and durable zero clearances available today!

Sandable Tabs

Some table saw manufactures list there specs as a certain size. The actual tolerances however can be slightly different from what the manufacture states due to the manufacturing process from saw to saw. The snug fit tab on the side of this insert can be sanded down so that the zero clearance fits just right for your saw and creates the perfect fit! This allows for a custom fit with out having to sand down the entire edge.

Side Screw

We have also added a snug fit side adjustable screw. This screw is to be adjusted in or out to eliminate any side to side play in the insert.By adjusting the side screw you will ensure a tight fit so that the insert does not move creating a true custom fit to your saw. This is important so that the insert stay as close to the cutting edge of the saw eliminating any possible tear out especially when cutting plywood.

End Screw

Much like the snug fit side adjustable screw, the snug fit end screw is to be adjusted if you have any play in the insert from the front to the back. This adjustment will allow you to custom the insert to your saw for that perfect fit eliminating any sort of movement in the insert.Once all your adjustments are set the pre-drilled finger hole makes removing the insert quick and simple.

Measure Before You Order

• Length = 13-3/8”
• Width = 3-3/4”
• Thickness = 1/2”
• Laminated Phenolic
• Side Snug Fit Screw
• End Snug Fit Screw
• Sandable Snug Fit Tabs

Product description

• Your purchase includes one Dewalt table saw, 10" 24-tooth carbide blade, rolling stand, push stick, miter gauge, rip fence, 2x blade wrenches, blade guard assembly manual
• Other Specs: Max rip to left of blade – 22” | Max rip to right of blade – 32-1/2” | Max width of Dado – 13/16” | Arbor size – 5/8” | Amps – 15 | Depth of cut at 45° – 2-1/4” | Depth of cut at 90° – 3-1/8” | No Load Speed: 4800 RPM
• Rolling stand designed for easy set up and breakdown with excellent stability
• Rack & Pinion Telescoping Fence System Make fence adjustments fast, smooth and accurate
• Features a 15.0A high torque motor with the power to cut pressure treated lumber and hardwoods

User questions & answers

Question:	Can i mount the axtra 8-outlet power strip on the table saw
Answer:	Can't see why not. Look online for Garmin-compatible charts, whether from Garmin or not. (My hiking map, with contours and more trails than the USGS maps, was a free download! Look around.) The eTrex models are waterproof, which is a plus. Think seriously about the display size, though. The whole unit fits in the palm of your hand, and its display is only a couple inches high. (See the specs. I might be off a little.) We hikers and hunters can stop and consult the unit, then start walking again. Your boat might travel quite a distance while you peer at that tiny screen, even with the engine stopped. Just a thought.Garmin obviously had boaters in mind when they programmed this, regardless of its size. It even has a "Man Overboard" function that instantly records its current location, then displays the distance and direction back to there while you turn the boat around. It shows tides, too, at whatever tide stations are close to you. Bottom line: it will do everything you need (I think) and do it all day and on into the next morning on a pair of AA cells, but your eyes will ask you why you didn't buy something with a bigger screen.
Question:	What are the dimensions of the unit on the stand when closed up. WxHxD? Need to know if it will fit in the storage cubby I have in the garage
Answer:	The maps that come preloaded are: Worldwide DEM Basemap (NR), Digital Globe demo (Jnx) and USGS Quads - Grand Canyon National Park (Jnx). Unfortunately, you will have to get the topo maps separately.
Question:	Does this saw accept dado blade set
Answer:	yes on the compass (electronic) but turn on the WAAS depending on if you set the compass for a true north or magnetic north WAAS gets rid of the errors jumping from satellite to satellite
Question:	How good would this saw be for a beginning woodworker on a limited budget
Answer:	The Oregon and all the Garmin "state" models all have a touch screen, don't they? The eTrex series doesn't. For controls it has the Power/battery check button and "back button on the right, and on the left, the zoom-in and -out buttons, plus the Menu button. On the front, at top-right, is the main control, a little thumbstick. Use it for scrolling and selecting menu items and for moving the map beyond your location.You'll want to spend some time reading the manual; this thing has a LOT of functionality. Most important shortcut: no matter how deep you go in the menus, double-tapping the Menu button takes you back to the main screen, with Map highlighted.

Product features

10" Jobsite Table Saw 32 - 1/2" (82.5cm) Rip Capacity, and a Rolling Stand

The DWE7491RS 10" Jobsite Table Saw 32 - 1/2" Rip Capacity, and a Rolling Stand has a 15 Amp motor and 32-1/2" rip capacity to allow cutting of large and hardwood materials. Features tool-free guarding component adjustments and fast, accurate fence adjustments. Rolling stand designed for easy set up and breakdown with excellent stability.

• Material support, can be used for narrow rip cuts
• Onboard storage system provides easy access to the Blade Guard Assembly, fence, riving knife, miter gauge, wrenches, push stick, and cord wrap when not in use
• Telescoping fence rails retract to create a small, portable package
• 15 amp Motor quickly rips through hardwoods with ease

Features

• Rack & Pinion Telescoping Fence System Make fence adjustments fast, smooth and accurate
• 32-1/2" rip capacity easily cuts a variety of larger shelving and trim materials
• Rolling stand designed for easy set up and breakdown with excellent stability
• Flip over ripping fence allows for narrow rip cuts
• 2-1/2" Dust Collection Port easily connects to a vacuum for efficient dust extraction
• 21-7/8" X 26 - 3/8" table provides superior material support

Product description

Introducing the 14 Table Saw Dust Collector Hood by POWERTEC. This well crafted dust collector table saw accessory works with an assortment of workshop woodworking applications, enhancing the efficiency of catching sawdust, dirt and debris. The dust hood features a 14 inch opening for optimal extraction and productivity. For convenience, this hood is a nominal 4 OD and was designed to fit the standard 4 inch ID dust collector hose. With the appropriate adapter, it is able to connect seamlessly to your Shop Vac, and can be utilized in a variety of positions, including beneath, behind or any convenient location on your machine. This also makes it suitable for a wide range of table saws, planers, drill press, sanding machines, and more. In addition, it possesses universal compatibility that accommodates many popular brands, including Delta, Ryobi, Craftsman and others. 3 Common Applications Solutions • Delta Contractor • Craftsman Table Saw • Ryobi Table Saw Premium Build The POWERTEC Table Saw Dust Hood was made with high quality ABS plastic. Whether attached to your table saw, planer or sanding equipment - this lightweight material ensures an impact resistant, anti-scratch and durable component built for everyday use. POWERTEC is a leading manufacturer of high quality woodworking tools and accessories, machines, and an assortment of OEM replacement parts. We are committed to exceeding expectations, while bringing the latest innovations, technology, and product development to the industry.

• INCLUDES: 14” Table Saw Dust Collector Hood
• FUNCTION: Makes a great seal for dust collection hose applications, ensuring optimum air quality while increasing workshop cleanliness by efficiently collecting dust, dirt and debris
• VERSATILE: Firmly attaches and secures to most table saws in a variety of positions (underneath or behind) and is ideal for a plethora of popular brand models, including Delta, Craftsman and others
• PREMIUM BUILD: Made with lightweight ABS plastic, featuring a high quality construction designed for strength and long-term durability to support your dust collection system
• DIMENSIONS: Outer size 14-1/16” x 14-1/16” with nominal 4” OD port (actual size tapers from 3-7/8” to 4”) and accepts standard 4” ID dust collector hose or 4” ID fittings

User questions & answers

Question:	More photos would be useful. Maybe a side view to show profile. And installed on a saw. Anyone
Answer:	I can get one but don’t have one right now
Question:	I have an older 10" craftsman table saw which i want to use this for dust collection in conjunction with a dust deputy. what adapters would i need
Answer:	I am in the same boat...I have the Craftsman 10" Table Saw Model # 218073. It comes with a bag, but I really want to eliminate sawdust so I am getting the Dust Deputy. What do you recommend I will need to attach this hood?
Question:	What’s the i.d. and o.d. of the dust port
Answer:	o.d. 3 3/4" i.d. 3 1/2" The 4" hoses fit it well.
Question:	Will this work with a Ryobi table saw
Answer:	You need to measure the opening below your saw where the sawdust drops to the ground. The dust fitting measures exactly 14 1/16" X 14 1/16". I attached mine with 1/2" self tapping sheet metal screws and it works great with my dust collector!!