13 best grizzly drills

Product description

If you want to set up a drilling station in a tiny room, or add a small, dedicated drill press to a crowded shop, this is the machine for you. Compact and light weight with an 8" swing and 5 spindle speeds this drill press will help you get the job done, whether you're a weekend hobbyist working out of your apartment or a full-fledged craftsperson running a production shop. Made in an ISO 9001 factory

User questions & answers

Question:	What is the Quill travel
Answer:	You mean how far down I can go? If so, 2"
Question:	Can I use a masonry bit to drill holes into bricks using this Drill Press
Answer:	Minimum rpm on the G0925 is 740 rpms. Boring up to 1/2” diameter in soft brick max rpm is 700. Masonry bits 1/2” and smaller cut more efficiently at approximately 500 to 700 rpm. Lower speeds equate to cleaner holes and extended bit life.
Question:	Country of origin
Answer:	This machine is manufactured in China.
Question:	what is the overall height ? looking for one to put on a flip table
Answer:	Fully assembled, I measured 23.5 Height * 15 depth * 9 width

• Motor: 1.5HP, 220V, 3-phase, 1720 RPM, 5.5A with variable frequency drive for operating on single-phase power
• Swing: 20-3/4"
• Max distance spindle-to-table: 17-1/2"
• Max distance spindle-to-base: 42"
• Table size: 23"L x 7-1/2"W x 1-3/4"H

• Motor: 600W (3/4 HP), DC, 110V, 5A
• Spindle taper: R-8
• T-slots: 3 @ 1-1/4" centers, 7/16" wide
• Head travel: 7-1/16"
• Head tilt: 45 degrees L/R

User questions & answers

Question:	Does this have plastic gears
Answer:	The drive pinion is metal and the other gears are synthetic. The replacement gears offered by littlemachineshop fit some other Grizzly machines but not this G0781.
Question:	Is this machine really only 2000 rpm, or is it actually 20k
Answer:	The range of vertical spindle speeds are 50 – 1000 RPM and 100 - 2000 RPM.
Question:	Is yours noisy? My drill press is much quieter than the 0781 mill
Answer:	No at all. Noise level is low
Question:	Does this mill accept standard collets or is it drill chuck only
Answer:	The G0781 3/4HP Mill/Drill has an R-8 spindle and uses a 7/16-20 draw bar. This machine will accept standard collets.

Product features

3/4 Horsepower Benchtop 4" x 18" Variable Speed Mill / Drill

Introducing the newest member of the Grizzly Mill/Drill lineup. This powerhouse comes equipped with a 600W high-torque DC motor, variable-speed controls, a high/low quick-change gearbox, digital readout display, and fine downfeed control, making quick work of whatever job is thrown at it.

Cast-Iron Table with Three 7/16" T-Slots

Digital RPM Display and Variable Speed

Fine Downfeed

Column Tilts 45 Degrees Left and Right

Specifications:

• Motor: 600W (3/4 HP), DC, 110V, 5A
• Spindle taper: R-8
• T-slots: 3 @ 1-1/4" centers, 7/16" wide
• Head travel: 7-1/16"
• Head tilt: 45 degrees L/R
• Max. distance spindle to table: 11-1/2"
• Swing: 12-3/4"
• Table travel (longitudinal): 11-13/16"
• Table travel (cross): 5-1/8" & Table size: 4-1/4" x 18"
• Range of speeds: Variable, 50 - 1000 RPM low, 120-2000 RPM high

• Main motor: 2 HP, 220V, 3-phase, 6.4A
• Coolant pump: 60W, 220V, 3-phase, 0.2A
• Max spindle-to-column distance: 13-1/2"
• Max spindle-to-table distance: 30-3/4"
• Spindle travel: 7"

• Motor: 1/2 HP, single-phase, 120V, 5A
• Footprint: 18" x 11"
• Overall height: 64-1/2"
• Spindle travel: 3-1/4"
• Spindle taper: JT-33

• This 5-speed bench-top radial drill press features variable swing up to 34-Inch and pivoting heads for drilling at just about any angle
• Truly versatile! Specifications: • Motor: 1/2 HP single-phase 110V • Overall height: 31-1/2-Inch
• 160-Inch • Drill chuck: 1/64-Inch-5/8-Inch • Swing: 34-Inch maximum

User questions & answers

Question:	what sort of clearance do i need behind the machine if i were to bolt it to a benchtop
Answer:	No less than 23inches behind from the back of the base to the wall... and, only to add, this unit MUST be bolted down as it becomes very unstable as motor is moved from (drill) centered position.
Question:	Does this drill press have a spindle lock
Answer:	If you mean can the spindle be locked to adjust for depth of cut yes. If this answer does not meet your question then I suggest you contact Grizzly. They can answer any question you may have on this machine. Hope this helps
Question:	What is the largest distance between holes one could drill without moving the material
Answer:	The measurement is simply the distance from the center of the spindle to edge of the column, then doubled. So if you measure 7.5 inches, you have a 15 inch drill press. This is referred to as the swing of the drill press which is the largest diameter piece this drill can handle. Swing on this machine I believe is 34". So if you clamp your project to the drill press table and drill your first hole you have 17" from the post to your spindle to deal with. Hope this helps. If you have any more techie questions call Grizzly they are very helpful in the tech support department.
Question:	Can I drill through a 6x6 fir block
Answer:	We would recommend you purchase a larger unit for that application. Attempting to drill through a 6"X6" piece of wood would require a larger capacity motor to get you the best results.

Product description

This great little machine sports some of the same features found on much larger mill/drills: Dovetail column, variable speed 3/4 HP motor, R8 spindle with digital read out, tapered gibs with double locks, and large 5-1/2" X 19-11/16" Table. This is an excellent value and great for just starting out or even as a dedicated, single-purpose machine in the shop! Purchase the optional D4780 stand for the ultimate mill/drill package.

• Motor: 3/4 HP, 110V, 8A, single-phase
• Spindle taper: R8
• Spindle travel: 2"
• T-slots: 3 @ 2-1/2" Centers, 7/16" Wide
• Head travel: 11"

User questions & answers

Question:	What is the height of this machine from bottom of base to the highest point ? paraplegic trying to build custom stand for this - thanks in advance for
Answer:	Verticle (Z axis) is on the right as the operator stands facing the machine. FYI the Z axis can be a bit heavy when there is a lot of repetitive up and down motion required. I rigged a gas spring that stands parallel to the column and counter balances the weight of the head. Used a 100# 30" oal with 12.8 stroke. Now cranking up and down is almost effortless.
Question:	Is there any way to tram the head on the machine
Answer:	The SHOP FOX Deluxe Milling Machine does not come with a power feed. The power feed, along with many other optional equipment can be seen at the manufacturer's(Woodstock International) website.
Question:	Is it "a large 7 1/16" x 26 5/8 table" or a "large 5-1/2" x 19-11/16" table?" both are mentioned in product description on this page
Answer:	The Model M1111 is designed for an 110V power supply. It requires a minimum of a 15 amp circuit.
Question:	What size chuck does this machine have
Answer:	Steel is not a problem. Its a question of how aggressive the cuts are and the sharpness of the tooling. Its no Bridgeport but adequate for all material and the tapping mode is something I have found extremely useful.

Product features

Shop Fox M1116 Variable-Speed Mill/Drill with Digital Readout

The M1116 Variable-Speed Mill/Drill is an important part of every hobbyist's or machinist's arsenal. Highlighting a dovetail column, variable-speed 3/4 HP motor, R8 spindle with a digital read out, tapered gibs with double locks, and a large 7 1/16" x 26 5/8" table, makes this awesome machine a must have for every shop.

3 Axis Digital Read-Out Display

The M1116 shows off a 3-Axis Digital Read Out display as well as a Digital Read out display on the spindle, allowing you to make sure you have the correct measurments and placement minimizing errors and wasted material.

Variable-Speed

Weather you need high speed or lower speed spindle operations this machine can handle it. Boasting a 50-2250 RPM spindle speed for the extreme precision your project needs.

Optional Stand for M1116 Mill/Drill

• Floor-to-table height: 37-1/2"
• Stand footprint: 15-3/4" x 16-1/2"

• Motor: 1 1/2 HP, single-phase, 120V/240V, prewired 120V
• Overall height: 70"
• Swing: 17"
• Spindle travel: 4-3/4"
• Number of speeds: 12 (210, 310, 400, 440, 630, 670, 1260, 1430, 1650, 2050, 2350, 3300 RPM)

• Motor: 3/4 H.P. single-phase 110V; Number of speeds: 12; Range of speeds: 140 260 320 380 480 540 980 1160 1510 1650 2180 3050 RPM Spindle
• Number of speeds: 12
• Range of speeds: 140 260 320 380 480 540 980 1160 1510 1650 2180 3050 RPM
• Spindle travel: 3-1/4-Inch
• Swing: 14-Inch

User questions & answers

Question:	Can this be moved with a hand truck
Answer:	Yes, but be very careful because it is top heavy. A tall appliance type hand truck would be best for more support and control.
Question:	How much voltage does this use
Answer:	STANDARD 110 VOLT
Question:	Where can I get a spare safety key
Answer:	Try your local hardware or home improvement store that sales tools.

• Motor: 1-1/2 HP, 120V/240V, single-phase, prewired 120V
• Swing: 20"
• Drill chuck: 3/64"–5/8"
• Drilling capacity: 1-1/4" steel
• Spindle taper: MT #4

• Motor: 1 HP, 110V/220V, single-phase, prewired 110V, 10A/5A
• Swing: 45"
• Drill chuck: 1/64"–5/8"
• Drilling capacity: 1-1/4" Steel
• Spindle taper: MT #3

User questions & answers

Question:	why can't you drill a 21/2 diameter hole with this machine
Answer:	You can, you just need the correct bit or hole saw
Question:	For metal grinding (burnishing with pads) will this allow me to essentially burnish a 90" square metal sheet
Answer:	No But maybe a 48” square.
Question:	Can the head be locked in to any degree up to
Answer:	Yes, I think it can go beyond that also

Product description

All the features and dependability of an expensive industrial grade drill press—with a price tag that's astoundingly low. Includes built-in light • Collar size: 2.595" • Precision-ground cast iron table • Table swing: 360-Degree • Table tilts: 90-Degree left and right • Overall height: 38" • Approximate shipping weight: 154-Pound.

• All the features and dependability of an expensive industrial grade drill press—with a price tag that's astoundingly low
• Includes built-in light
• Specifications: • Motor: 3/4 HP 110V single-phase • Swing: 14-Inch • Drill chuck: 1/64-Inch–5/8-Inch

User questions & answers

Question:	When the table is all the way down, what is the distance between the chuck & the table
Answer:	No idea about the warranty. Right out of the box, it didn’t work. Sent it back and got a different brand.
Question:	Where is this drill press made
Answer:	The voltage is 110V/50Hz.
Question:	I know this is a dumb question but I'm new to carpentry and I want to cut circular holes with forstner bits will this drill do the job
Answer:	The length of cord is about 1.5 meters.
Question:	does this drill press have a draw bar
Answer:	Yes, pls plug in.

Product features

3/4 Horsepower 12 Speed Benchtop Drill Press

All the features and dependability of an expensive industrial grade drill press at a great value. Includes built-in light (bulb not included).

Table Tilts 90 Degrees Left and Right

104-3050 Speed Range

Threaded Depth Gauge

Crank Handle Operated Rack and Pinion Vertical Table Movement

Specifications:

• Motor: 3/4 HP, 120V, single-phase, 7.5A
• Swing: 14"
• Drill chuck: 3/64"–5/8"
• Drilling capacity: 3/4" steel
• Spindle taper: MT #2
• Spindle travel: 3-1/4"
• Number of speeds: 12 (140, 260, 320, 380, 480, 540, 980, 1160, 1510, 1650, 2180, 3050 RPM)
• Quill flange/collar dia: 2.595"
• Table swing: 360°
• Table tilts: 90° left & right

• Drill square sided mortises with this Bench top Mortising Machine
• Rigid cast iron construction and a rack and pinion head control mechanism slides on a dovetailed column with adjustable ways to ensure precision mort
• A pneumatic return strut eases the step and repeat cycle of multiple drilling

User questions & answers

Question:	How do you adjust the fence? Is it easy and accurate? Thoughts on getting the work piece into position
Answer:	Very thin and flexible but they stay in place very well.
Question:	does this machine come with chisels
Answer:	Yes, the silver dangley pair and the plain silver tunnels are both screw fit types.
Question:	what is the chusk size? 3/8 or
Answer:	No only the size you order them in.

Product features

1/2 HP Benchtop Mortising Machine

Rigid cast-iron construction and rack-and-pinion head control on a dovetail column help ensure this Benchtop Mortising Machine will produce precision mortises every time. A pneumatic return strut eases the step-and-repeat cycle when making multiple mortises. A riser block is also included to increase the maximum stock thickness to 6". The 1/2 HP motor powers through any type of wood and the easy-access drill chuck makes it simple to change chisels. Includes 4 mortising chisels!

Includes 1-3/4" Riser Block

Dovetail Column with Adjustable Ways

Multi-Positional Handle

Adjustable Depth Stop

Specifications:

• Motor: 1/2 HP, 110V, single-phase, 6A
• Spindle speed: 1725 RPM
• Spindle taper: JT #2
• Spindle travel: 3-1/4"
• Chuck size: 3/8"
• Collar size: 5/8"
• Maximum stock width: 8-1/2"
• Maximum stock thickness with extension block: 6"
• Maximum mortising depth: 3"
• Maximum chisel travel: 4-5/8"