10 best tekton impact guns

Product description

TEKTON impact external star sockets have both a high-visibility laser size marking and a permanent stamped marking that won't wear off. They're designed for use with both friction ring anvils and detent pin anvils. Their internal 6-lobe geometry is designed for a high-torque fit that resists slipping. Made of high-performing 6140 Cr-V steel.

• Size is marked both with a high-visibility laser marking and a permanent stamped marking that won't wear off
• 6-lobe geometry is designed for a high-torque fit that resists slipping
• Made of high-performing 6140 Cr-V steel with a protective manganese phosphate finish
• Overall Length: 1.5 inches
• Drive End Diameter: 0.93 inches
• Socket End Diameter: 0.66 inches
• Socket Well Depth: 0.39 inches

User questions & answers

Question:	Does it come with a case or bag
Answer:	The top of the handle is marked with the style and size of the driver. I think it would hold up pretty well to a hammer, but then you're not supposed to do that to a screwdriver.
Question:	Are the screw driver shafts hexagonal
Answer:	No, they are in a regular plastic package like other product you buy.
Question:	Are the tips magnetic or just the screw holder
Answer:	The 'Desalt' logo is stamped into the black rubber. The Rubber improves grip and allows for better bare-hand use. High quality.
Question:	Is it made in America
Answer:	No the tip is black oxide which makes it stronger. I have done the following to make any metal tool magnetic. (Found online)*********Take the magnet in one hand and take the screw driver in the other hand. Start by placing the shaft end (near the handle) of the screw driver onto the magnet and run the length of the shaft along the magnet to the tip of the screw driver. Do this slowly but not extremely slowly. Come back and repeat the same motion four or five times.Test again by touching the tip of the screw driver to the metal screw. If the metal screw responds by lifting up on the tip of the screwdriver you will have achieved a good level of magnetism. If there is a light lift but the screw doesn't pick up on the tip, try running the screwdriver shaft along the strong magnet a few more times and then test again.

Product description

Built for use with impact tools, the TEKTON 4-pc. 1/2 in. Drive Impact Flip Socket Set includes the six most common sizes for lug nuts. The six-point design offers a snug fit and sure contact with the broad, flat sides of a lug nut, not just the corners, preserving its geometry and preventing round-off. Thinner walls give sockets the clearance to slide into tight recessed wells where many other impact sockets can't go. Made of forged and hardened chrome molybdenum steel, each socket has a durable black electroplated finish. Color coding allows for quick size identification.

Set Includes:



1/2-inch drive 6-point impact flip sockets:

• 17 mm by 19 mm (red)
• 13/16 in. by 3/4 in. (blue)
• 21 mm by 7/8 in. (yellow)

3-inch by 1/2-inch drive extension bar

Storage case

From the Manufacturer

Covering 6 of the most common lugnut sizes, the TEKTON 4-Piece 1/2" Drive Impact Flip socket set features professional-grade quality.

• Includes 3-pc. 1/2 in. drive impact flip sockets: 17 mm x 19 mm, 3/4 in. x 13/16 in., 21 mm x 7/8 in.; 1-pc. 1/2 in. drive impact extension bar: 3 in.; Storage case
• Drop forged, heat treated chrome molybdenum steel
• Black oxide finished extension bar
• Black electro plated finished sockets
• Color coded sockets for quick size selection

User questions & answers

Question:	What is the usable depth of each socket ? Are they as deep as the TEKTON deep impact sockets? I need at least 1-1/2" deep, maybe
Answer:	1 1/2 inch from top to center
Question:	Can someone tell me the outside diameter of the 21mm socket? I have after market wheels with a clearance of 1.1" for the lug hole
Answer:	1.14 to 1.15 inches. The other who posted 1.225 inches measured the 7/8" side of the socket.Looks like this socket is 40-50 thou bigger than your clearance available.
Question:	I was curious. if these are the thin walled sockets ? i have noticed when i go to get my tires rotated the mechanic has to use a thin walled socket
Answer:	They are thin walled sockets. I have some very tight spaces between my lug nuts and rims on two trucks I own. Normal impact sockets won't work so I ordered this TEKTON set. They work great and fit nicely on the lug nuts.
Question:	What is the flip socket? It seems that both ends have 6 point (hex). How to use it with 1/2" (square) wrenches or the 1/2" drive extension bar
Answer:	Both ends have a hex of different sizes. Two sizes, one socket. In the middle of each flip socket is a 1/2" drive tang that you slip the extension that comes with the kit into the opposite end that you need for the lug nuts. Think of it working like any other socket except there's a an extra socket sticking out.

Product features

TEKTON 4950 1/2-Inch Drive Lug Nut Service Impact Flip Socket Set

Covering the most common lug nut sizes, the TEKTON 4950 1/2-inch Drive Impact Flip Socket Set can take on almost every lug nut service project.

Heavy-Duty Construction

Built for use with impact tools, the lug nut service flip impact sockets efficiently transfer torque from impact wrench to fastener, loosening the most stubborn lug nuts. Made from high-strength chrome molybdenum steel, these impact sockets are more resistant to drive end round out than standard impact sockets, resulting in a longer useable life.

Color-coded Sizes

Each flip socket has a black electro plated finish and color-coded for fast size selection.

Storage Case

The three flip impact sockets and extension bar fit snug in the blow-molded storage case. Keep the case stored in a tool chest or carried to your job site.

Product description

Increase your access with the TEKTON 3-pc. Impact Universal Joint Set. Engineered for use with impact drivers, these problem solvers work around obstructions and get into tight spots, delivering the torque needed to break loose stubborn fasteners. Giving you just the right angle when space is limited, they save you time and help you avoid unnecessary disassembly steps. Made from premium chrome vanadium steel, they are precisely heat treated for superior strength and protected by a corrosion-resistant black oxide finish.

Set Includes:

• Universal joints: 1/4, 3/8, 1/2 in.

From the Manufacturer

Drop Forged, Heat Treated Chrome Vanadium Steel, Corrosion-Resistant Black Phosphate Finish, Locks on to Socket and Drive Tang. Contents: 1-pc. 1/4-Inch Drive, 1-pc. 3/8-Inch Drive, 1-pc. 1/2-Inch Drive.

• Includes: impact universal joints: 1/4, 3/8, 1/2 in. drive
• Engineered for use with impact drivers
• Works around obstructions to access hard-to-reach fasteners
• Spring-loaded detent balls securely latch onto sockets, preventing them from being dropped
• Through-hole in drive ends locks onto drive tang
• Made of premium chrome vanadium steel with a protective black oxide finish

User questions & answers

Question:	Can I use a torque wrench
Answer:	Yes, it identifies the type of driver, but not the size
Question:	can you stack them to do tighter angles
Answer:	It has like a spring steel detenti around the magnet and with a little pressure it’ll pop off. Best set of screwdrivers I’ve owned for fitment on a screw
Question:	If I break one of these how do I get it warranted
Answer:	It does not say where they are made anywhere on the screwdrivers and a fairly thorough Google search didn't reveal the answer either. I'm guessing that since most made in the US products proudly mark their products as such, the lack of that marking answers the question. Research shows me that Dewalt tools not made in the US are manufactured in either Mexico, Brazil, Italy, the UK, Czech Republic, or China. I'm not happy with this myself and was disappointed when I found out while answering your question. I will add, however, that they are really great screwdrivers. Probably the best I've used in quality, comfort in the hand, and the way the tips fit into screws which is hard to describe but true. If I had a chance to redo the purchase knowing what I know now, I would probably still buy them. They are that nice in my opinion.
Question:	Where are these products made
Answer:	I am not sure where they are made. There is no marking anywhere on the drivers that indicate where they are made. I no longer have the packaging. I do really like the drivers though. Perfect handle size and rubber no-slip texture.

Product features

TEKTON Impact Universal Joint Set, Cr-V, 3-Piece | 4964

Engineered for use with impact drivers, the problem solvers in the TEKTON 3-pc. Impact Universal Joint Set work around obstructions, giving you just the right angle when space is tight.

Product description

Outfitted with one 1/4 in. NPT female end and one 1/4 in. NPT male end that swivels 360 degrees, the TEKTON 3 ft. x 3/8 in. I.D. Rubber Lead-In Air Hose connects air tools to line hoses or air hose reels. Acting in part as a sacrificial piece, it protects longer, more valuable hoses from intense wear, greatly extending their service life. Its swivel end gives the tool extra range of motion to prevent the hose from getting twisted and tangled as you move around and change positions. Solid brass end connectors never corrode and seal better against leaking than aluminum, steel, or zinc. CALIFORNIA WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, birth defects or other reproductive harm. Please wash your hands after use.

• Sacrificial hose absorbs intense wear at tool connection to protect more valuable parts of the system
• Flexible rubber stays soft and easy to work with even at -40 degrees F
• Spiral yarn reinforcement prevents wall failures at temperatures up to 190 degrees F
• Solid brass connectors never corrode and seal better than aluminum, steel, or zinc

User questions & answers

Question:	does the "swivel end" rotate so I can screw it into a fixed device on both ends
Answer:	One end swivels the others does not
Question:	Does any one know if this hose (3/8-inch. i.d.) is the type of hose i need to work with a bostitch miiifn floor nailer
Answer:	It can work with any air tool. I would recommend atleast 25 ft length. You will need the couplings for the ends also.
Question:	Is the end that does not rotate a male or female thread ? the pictures seem to show it as both
Answer:	I have the 46347 hose and the swivel end is male while the rigid end is female. The description is very confusing in that sometimes it's mentioned both ends are male, while other spots mentions one male one female.
Question:	Will the inner diameter of the swivel only serve to bottleneck larger V style fittings? I want to maintain the highflow benefit of V coupler/plugs
Answer:	The swivel does have a slightly reduced diameter. For best air flow, I would use straight fittings.

Product features

TEKTON 46347 3-Feet x 3/8-Inch I.D. 250 PSI Rubber Whip Air Hose

Outfitted with one 1/4-inch NPT female end and one 1/4-inch NPT male end that swivels 360 degrees, the TEKTON 3-Feet x 3/8-Inch I.D. 250 PSI Rubber Whip Air Hose connects air tools to a line hose or hose reel, protecting these parts from intense wear and giving the tool extra range of motion.

Protects Main Hoses

This short length of hose is designed to connect tools to line hoses and air hose reels. Acting in part as a sacrificial piece, it protects these longer, more valuable hoses from intense wear, greatly extending their service life.

360-Degree Swivel

The female end connects to the main hose, while the swivel end gives the tool extra range of motion to prevent the hose from getting twisted and tangled as you move around and change positions.

Extreme Performance

Made in the U.S.A. of premium flexible rubber, hose stays soft and easy to work with, even at 40 degrees Fahrenheit below zero, yet still takes the heat up to 190 degrees Fahrenheit without swelling or bubbling.

Product description

Work faster and avoid unnecessary disassembly steps with the TEKTON 3-pc. 1/2 in. Drive Impact Extension Set. Engineered for use with impact drivers, they reach past obstructions or into tight, narrow spaces and deliver the torque needed to break loose stubborn fasteners. A spring-loaded detent ball securely latches onto sockets, preventing them from being dropped or left sticking on fasteners. The through-hole in the drive end locks onto the tang of impact wrenches or drivers. To protect against rust and corrosion, the black oxide finish absorbs and holds oil, repelling moisture.

Set Includes:

• 1/2 in. drive extensions: 3, 6, 8 in.

From the Manufacturer

Forged and Hardened Chrome Vanadium Steel, Corrosion-Resistant Black Oxide Finish, Locks on to Drive Tang, Spring-Loaded Ball Bearing Socket Retainer. Contents: 1-pc. 1/2-Inch Dr x 3-Inch Extension Bar, 1-pc. 1/2-Inch Dr x 6-Inch Extension Bar, 1-pc. 1/2-Inch Dr x 8-Inch Extension Bar.

• Includes 3-pc. 1/2 in. drive impact extension bars: 3, 6, 8 in.
• Engineered for use with impact drivers
• Adds length to access hard-to-reach fasteners
• Spring-loaded detent balls securely latch onto sockets, preventing them from being dropped
• Through-hole in drive ends locks onto drive tang
• Made of premium chrome vanadium steel with a protective black oxide finish

User questions & answers

Question:	will these work on oil drains from riding lawn mower
Answer:	Bench acrylic only
Question:	Are they made in China? or Taiwan? or USA
Answer:	On the back of your tanning bed there should be a sticker that has the make model or year of the tanning bed. In front of the 24 there may also be a letter that will give us the year. E - 1996, F-1997, G-1998, H-1999, J-2000, K-2001, L-2002, M-2003, N-2004, P-2005, R-2006, S-2007, T-2008, V-2009, W-2010, X-2011
Question:	Do these extensions come in a case
Answer:	It's a bronze color.
Question:	With these extensions on the Tekton 1/2" drive torque wrench, will the torque wrench still be accurate
Answer:	It can leave a light stain after several uses. I always wear something I don't mind getting discolored so the clothing is exposed to the lotion repeatedly .. hope this helps ..

Product features

TEKTON 1/2-Inch Drive Impact Extension Bar Set, Cr-V, 3-Piece | 4971

Engineered for use with impact drivers, the three different lengths in the TEKTON 3-pc. 1/2 in. Drive Impact Extension Set reach past obstructions or into tight, narrow spaces, accessing hard-to-reach fasteners without unnecessary disassembly steps.

Product description

Made in the U.S.A of premium flexible rubber, the TEKTON 50 ft. x 1/2 in. I.D. Rubber Air Hose delivers superior performance in extreme conditions. It stays soft and easy to work with, even at a frigid 40 degrees F below zero. At temperatures as high as 190 degrees F, spiral yarn reinforcing prevents heat-related wall failures like swelling or bubbling. Solid brass end connectors never corrode and seal better against leaking than aluminum, steel, or zinc. Bend restrictors relieve the strain near hose ends, preventing kinks that choke off air flow and can damage the hose over time. CALIFORNIA WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, birth defects or other reproductive harm. Please wash your hands after use.

• Flexible rubber stays soft and easy to work with even at -40 degrees F
• Spiral yarn reinforcement prevents wall failures at temperatures up to 190 degrees F
• Solid brass connectors never corrode and seal better than aluminum, steel, or zinc
• Bend restrictors relieve strain and prevent kinks in the high-stress area near hose ends
• Made in the USA

User questions & answers

Question:	Which is the O.D. of this product please
Answer:	No
Question:	Would this hose work for propane
Answer:	Doesn't matter because Amazon seller rates lower than a zero. Dealer lied about shipment, never sent the product.
Question:	can anyone tell me how to test the pressure at the end of the hose? so i know how much my air tool is getting etc
Answer:	Yes, easy to install, but if you want to adjust above the plate, you will have to drill a hole for it. I used 1/4 drill bit.
Question:	Is there really Lead in this hose
Answer:	No

Product features

TEKTON 46367 50-feet x 1/2-inch I.D. 250 PSI Rubber Air Hose

Delivering superior performance in extreme conditions, the TEKTON 50-feet x 1/2-inch I.D. 250 PSI Rubber Air Hose stays soft and easy to work with in deep cold and won't swell or bubble in blistering heat.

Superior Flexibility

Made of premium flexible rubber, the hose stays soft and easy to work with, even at a frigid 40 degrees fahrenheit below zero.

Handles the Heat

At temperatures as high as 190 degrees fahrenheit, spiral yarn reinforcing prevents heat-related wall failures like swelling or bubbling.

Bend Restrictors

Relieving the strain near hose ends, bend restrictors prevent kinks that choke off air flow and damage the hose over time.

Product description

TEKTON impact sockets have both a high-visibility laser marking and a permanent stamped marking that won't wear off. They're designed for use with both friction ring anvils and detent pin anvils. Precise 6-point openings provide an exact fit for hex fasteners. Each socket size meets a minimum of 1.3 times the ANSI/ASME standard for proof torque.

• Includes 17-pc. 1/2 inch drive 6-point inch impact sockets: 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/8, 1-3/16, 1-1/4 in.; 17-pc. 1/2 inch drive deep 6-point inch impact sockets: 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/8, 1-3/16, 1-1/4 in.; 25-pc. 1/2 inch drive 6-point metric impact sockets: 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32 mm; 25-pc. 1/2 inch drive deep 6-point metric impact sockets: 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32 mm; 2-pc. 1/2 inch drive impact extensions: 3, 10 in.; 1-pc. impact universal joint: 1/2 in. drive; Storage case
• Sizes are marked both with a high-visibility laser marking and a permanent stamped marking that won't wear off
• 6-point socket openings provide an exact fit for hex fasteners
• Radiused corners prevent fastener round-off by applying force to a fastener's flat sides, rather than its corners
• Meets a minimum of 1.3 times the ANSI/ASME standard for proof torque
• High-density polyethylene case withstands common lubricants, fuels, and solvents

User questions & answers

Question:	Hi Tekton tools is this the new style of Impact Sockets yall making
Answer:	No case or bag good screwdrivers though.
Question:	Can these also be used with a braker bar
Answer:	No.
Question:	What is the total length of the standard depth sockets
Answer:	Nope. Just the screw holder.
Question:	What country of origin are these made in
Answer:	All DeWalt tools are made in America! There are some working parts like motors and stuff that I think are from around the world but they are all assembled in the USA. And I've never had a problem with any Dewalt product warranty. Whenever I have something break of Dewalt I just call Dewalt and they will replace it because most of their products have a lifetime warranty on their hand tools

Product features

Two Size Markings

The size is marked in two ways on every socket—both as a high-visibility laser marking and a permanent stamped marking.

Full-Length Socket Well

Whether in standard or deep length, the interior well extends far into the socket, which allows better fastener engagement in more situations.

Fully Stepped Shoulders

The narrowed socket diameter goes all the way down to the base of the socket on small, deep-length sizes. This allows for better reach into tight, recessed areas.

Prevents Fastener Round-Off

Radiused corners prevent fastener round-off by applying force to a fastener’s flat sides, rather than its corners.

Product description

TEKTON 3/8 inch drive 12-point sockets are an exact fit for double hex fasteners and also work with hex and square shapes. They're designed to grip the sides and not the corners of the fastener heads, which prevents round-off. The large, die-stamped markings are permanently impressed into the material and optimized for readability.

• Includes 15-pc. 3/8 in. drive 12-point sockets: 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1 in.; 19-pc. 3/8 in. drive 12-point sockets: 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24 mm; Socket rails and tray
• 12-point opening fits double hex (12-sided), hex, and square-shaped fasteners
• Socket geometry is designed to apply force to flat sides of fasteners and not the corners, preventing round-off
• Standard-length socket is relatively versatile and suitable for a wide range of applications
• Extra-large die-stamped size markings are easy to read and can’t wear off
• Polished, chrome-plated finish easily wipes clean and is highly resistant to corrosion
• Four detent grooves provide a secure connection with the drive tool

User questions & answers

Question:	what does standard lenght mean? Shallow or deep
Answer:	Not the best use for a swivel socket, you are already losing torque.
Question:	What is the length of the socket rail
Answer:	A friend of mine had to warranty a Tekton ratchet, he took a photo of the broken ratchet with his phone, sent the photo to Tekton via their website, 2 days later he had a new ratchet in his mailbox. In my opinion Tekton has one of the best warranties in the business
Question:	where are these manufactured
Answer:	Below the UPC it states: made in Taiwan

Product features

Large, Stamped Markings

Roll-stamped markings are permanently impressed into the material and are clear even in low light settings.

Prevent Fastener Round-Off

Radiused corners in the socket opening apply force to a fastener's flat sides, rather than its corners.

Secure Drive Tool Engagement

Four detent grooves in the socket drive end provide a secure connection with the retaining ball of a drive tool.

Socket Rail Storage

Patented twist-to-lock design securely holds sockets on the rail. Keyhole slot mounts to wall or workbench.

Product description

This complete set includes all 1/2 inch drive accessories offered by TEKTON: 3, 6, 10 inch extensions, pinless universal joint, 1/2 inch to 3/8 inch drive reducer, and 1/2 inch to 3/4 inch drive adapter. All tools are protected with a corrosion resistant manganese phosphate finish.

• Includes: 3-pc. 1/2 inch drive impact extensions: 3, 6, 10 in.; 1-pc. impact reducer: 1/2 in. drive (F) x 3/8 in. (M); 1-pc. impact adapter: 1/2 in. drive (F) x 3/4 in. (M); 1-pc. impact universal joint: 1/2 in. drive
• Engineered for use with impact drivers
• Adapter and reducer convert 1/2 inch drive impact drivers to 3/4 inch or 3/8 inch drive
• 3, 6 and 10 inch extensions add length to access hard-to-reach fasteners
• Universal joint works around obstructions and operates smoothly at up to a 30-degree angle
• Spring-loaded detent ball securely latches onto sockets, preventing them from being dropped
• Through-hole in drive end locks onto drive tang
• Corrosion resistant manganese phosphate finish

User questions & answers

Question:	Dose it come in a case
Answer:	The usual practice is anything less than 15 degrees of deflection may be disregarded. Over that, there is no linear correction factor or similar, so in general use of a u-joint and torque wrench is not recommended.

Product description

TEKTON 4957 Impact Adapter and Reducer Set, Cr-V, 4-Piece

Be ready for anything with the TEKTON 4-pc. Impact Adapter and Reducer Set. Engineered for use with impact drivers, these problem solvers give you more options for dealing with the unexpected. They create solutions for lost or broken sockets, fill the gaps in incomplete size ranges, and extend the capability of your existing socket system. Made from premium chrome vanadium steel, they are precisely heat treated for superior strength and protected by a corrosion-resistant black oxide finish.

TEKTON 4971 1/2-Inch Drive Impact Extension Bar Set, Cr-V, 3-Piece

Work faster and avoid unnecessary disassembly steps with the TEKTON 3-pc. 1/2 in. Drive Impact Extension Set. Engineered for use with impact drivers, they reach past obstructions or into tight, narrow spaces and deliver the torque needed to break loose stubborn fasteners. A spring-loaded detent ball securely latches onto sockets, preventing them from being dropped or left sticking on fasteners. The through-hole in the drive end locks onto the tang of impact wrenches or drivers. To protect against rust and corrosion, the black oxide finish absorbs and holds oil, repelling moisture.

Bundle Includes:

• 3/8 in. drive (F) to 1/4 in. drive (M) reducer
• 1/2 in. drive (F) to 3/8 in. drive (M) reducer
• 1/4 in. drive (F) to 3/8 in. drive (M) adapter
• 3/8 in. drive (F) to 1/2 in. drive (M) adapter
• 1/2 in. drive extensions: 3, 6, 8 inch

• Engineered for use with impact drivers
• Common size combinations of the adapter and reducers multiply the range and capability of any socket set
• Extensions add length to access hard-to-reach fasteners
• Spring-loaded detent balls securely latch onto sockets, preventing them from being dropped
• Through-hole in drive ends locks onto drive tang
• Made of premium chrome vanadium steel with a protective black oxide finish