6 best table saw accessories

• This 5 piece safety kit is designed to be your essential safety protection to help from getting to close to the cutters or blades on a router table, shaper, band saw, table saw and jointer. From the narrow v-style push stick, to the beefy long push block, this kit has all the bases covered in regards to many different woodworking applications.
• Each device in this kit is intentionally made in the SAFETY ORANGE color for high visibility when in use. This provides the user the ability to see exactly there hands are at during the cutting or milling process. Being SAFETY ORANGE also allows for you to easily find the device when its not in its normal location.
• The general idea behind these safety devices is to help you guide and control your stock when feeding through a table saw, band saw, jointer or a router table. The push blocks are generally used on jointers and some router applications, while the push sticks are primarily used on table saw projects. All five devices help prevent kickback and protect your fingers and hands during your cutting process
• Soft, receptive, rubber foam pads line the bases of the two small push blocks and the large push block. The rubber soles make pushing and controlling your stock much easier and safer then when doing it by hand. The soles are also washable with with warm water. Must let the rubber soles dry for 24 hours prior to using them again.
• The 5 piece safety kit includes 2 each small push blocks (1 angled handle and 1 offset handle small push block), 1 each long or large push block, 1 each standard width push stick and 1 narrow width safety-v push stick.

Product features

Keep your fingers out of harms way...

This 5 piece safety kit is designed to be your essential safety protection to help from getting to close to the cutters or blades on a router table, shaper, band saw, table saw and jointer. From the narrow v-style push stick, to the beefy long push block, this kit has all the bases covered in regards to many different woodworking applications.

Orange for Safety

Each device in this kit is intentionally made in the SAFETY ORANGE color for high visibility when in use. This provides the user the ability to see exactly there hands are at during the cutting or milling process. Being SAFETY ORANGE also allows for you to easily find the device when its not in its normal location.

Why pay more?

• The general idea behind these safety devices is to help you guide and control your stock when feeding through a table saw, band saw, jointer or a router table. The push blocks are generally used on jointers and some router applications, while the push sticks are primarily used on table saw projects. All five devices help prevent kickback and protect your fingers and hands during your cutting process
• Soft, receptive, rubber foam pads line the bases of the two small push blocks and the large push block. The rubber soles make pushing and controlling your stock much easier and safer then when doing it by hand. The soles are also washable with with warm water. Must let the rubber soles dry for 24 hours prior to using them again.
• The 5 piece safety kit includes 2 each small push blocks (1 angled handle and 1 offset handle small push block), 1 each long or large push block, 1 each standard width push stick and 1 narrow width safety-v push stick.

Keeping Your Distance Is Key

This 5 piece safety kit is designed to be your essential safety protection to help from getting to close to the cutters or blades on a router table, shaper, band saw, table saw and jointer. From the narrow v-style push stick, to the beefy long push block, this kit has all the bases covered in regards to many different woodworking applications. Each device in this kit is intentionally made in the SAFETY ORANGE color for high visibility when in use. This provides the user the ability to see exactly where there hands are at during the cutting or milling process. Being SAFETY ORANGE also allows for you to easily find the device when its not in its normal location. The general idea behind these safety devices is to help you guide and control your stock when feeding through a table saw, band saw, jointer or a router table. The push blocks are generally used on jointers and some router applications, while the push sticks are primarily used on table saw projects. All five devices help prevent kickback and protect your fingers and hands during your cutting process. Soft, receptive, rubber foam pads line the bases of the two small push blocks and the large push block. The rubber soles make pushing and controlling your stock much easier and safer then when doing it by hand. The soles are also washable with with warm water. Must let the rubber soles dry for 24 hours prior to using them again. The 5 piece safety kit includes 2 each small push blocks (1 angled handle and 1 offset handle small push block), 1 each long or large push block, 1 each standard width push stick and 1 narrow width safety-v push stick.

Durable and Built to Last!

Each device in this set is made from a super durable polymer plastic to stand up to everyday use. They are almost indestructible! Each of the blocks with foam pads are designed to grip the material. If they become built up with dust and debris, clean them with warm soapy water and let them dry for at least 24 hours before using them again.

• Adjustable height from 27-in to 43-in
• Highly visible edge guides keep work in place
• Eccentric foot keeps stand stabilized on uneven surfaces
• Portable, Light-Weight design folds for convenient storage
• Load capacity: 250 pound

User questions & answers

Question:	How wide is roller only
Answer:	11 1/2 in
Question:	Is the roller removable
Answer:	Yes, the roller can be removed.
Question:	Where is this manufactured
Answer:	China by Hangzhou Great Manufacturing Company
Question:	Are the bearings steel or plastic
Answer:	Dear, the bearings are steel.

Product features

WORKPRO Folding Roller Stand Height Adjustable, Pedestal with Ball Bearing Roller

• Folding Roller Stand Height Adjustable, Pedestal with Ball Bearing Roller, Works with Table Saws, Miter Saws, Planers and Jointers for Log, Timber, Firewood and Metal Material
• Load capacity: 250 pound

Portable, light-weight design folds for convenient storage

• Edge guides
• Adjustable height
• Knob
• Steel frame and legs
• Eccentric foot

• The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
• The .200” thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
• The head is mounted to a solid steel miter bar that measure 18” in length and is .353” thick by .730” wide. Standard miter slots (not Craftsman or Sears brands) are 3/4” x 3/8” with a 1/8” “T” slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8” in diameter and is just shy of 1/8” to fit into to the “T” slot to prevent accidental lifting when feeding your stock through.
• Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
• Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.

Product features

Fulton Precision Miter Gauge with Aluminum Miter Fence and Flip Stop

We've all done the research or at the very least heard about miter gauges with fence systems that are very accurate, easy to adjust and make cross cutting angles on your table saw super easy. While that all sounds great, all those great features usually costs a lot. That is until now! The Fulton Precision Miter Gauge with Aluminum Miter Fence and Flip Stop comes packed with all those great features and more. The best part is that it is reasonably priced so that most any woodworker can afford it!

Be Precise with Ease

If you have ever used a factory supplied miter gauge, then you know how limiting it can be. The Fulton Miter Gauge with Aluminum Fence and Stop makes the angle cutting process a breeze. Once the gauge is set and the fence is properly adjusted, cross cutting angles on your table saw just became a whole lot easier than just using a miter gauge by itself. When this aluminum fence is used with the Fulton Miter Gauge, you'll be able to repetitively cut angle stock all day long with precise results!

MAXIMUM Workpiece Support

When designing the fence for this system we kept having the same issue happen over and over again. The standard 90 degree end on most miter gauge fences made the fence to saw blade gap too large and the wood kept binding in that gap. Our solution was to simply cut the fence ends at a 45 degree angle so that the fence can get as close as possible to the blade with minimal stock over hang. This helps prevent binding and produces a much cleaner cut.

Convenient Aluminum Flip Stop

Included with the fence and miter gauge is a convenient flip stop for making repetitive cuts. Simply slide the flip stop to the exact position you need it to be, lock it in place and you're ready to go! When the stop is not needed you can either remove from the fence or simply lift the stop upwards and out of the way until it is needed.

Accurate and Easy to Adjust

The Fulton Miter Gauge is loaded with great features. One of the more prominent features are the positive stops that are set to the most common angles used by woodworkers. Simply loosen the handle by rotating it counter clockwise, pull the spring loaded pin lock up and and adjust the miter gauge to the desired angle. Once you find your positive stop angle, release the lock pin so it locks the angle in place and re-secure the handle by rotating int clockwise until it is snug. If you want to use an angle that is not one of the positive stops, the pin lock can be pulled upward and rotated so that it won't engage any of the positive stop holes. This allows you to adjust the miter gauge to any angle you need.

Left Side, Right Side or Even Upside Down...

For the most part, we tend to cut on one side of our table saw the majority of the time. It usually depends on the saw or just simply preference. This is why we included two different sticky back (PSA pressure sensitive adhesive) tapes so you can choose which direction you need. We also know that some of use like to do things a little differently. If you are looking down at your miter fence from above then it may make sense for some of us to place the tape on to the aluminum fence upside down in relation to the miter gauge. This allows for you to be able to clearly read the measurements on the tape.

Standard Size Miter Bar 3/4" x 3/8"

The steel miter bar is mounted to the miter gauge and is the industry standard of 3/4" x 3/8". This means it will fit into most table slot miter slots. The miter bar also features spring loaded plungers that can be adjusted (with a hex key wrench) for just the right fit so you have a smooth push through every time.

Product description

If you’ve ever injured your hand operating power or table saw equipment while maneuvering stock materials – then you know the importance of hand safety, and keeping them away from blades and cutters. Whether you’re a novice or experienced DIY type of person, taking the necessary steps towards preventing accidents is part of being a professional. Introducing the Deluxe L- Shaped Push Sticks by POWERTEC. These well crafted l-shaped style of push sticks (or sometimes referred to as V-type push sticks) are the perfect addition to any woodworking tool set. Not only do they help keep your hands out of harms way, but they reduce the risk of kickback, and often result in smoother cuts, producing a more professional looking finish. Unlike the traditional straight push stick version, these give you the ability to get a bit closer to the blade, taking more of a “hands-on” approach, and in most cases simply using one stick to push the entire workpiece down. This deluxe version allows you to comfortably grip the handle without having to shift or adjust your grip during application (which can be extremely unsafe). These woodworking tool accessories ensure optimal versatility, and can be used with a variety of machines, including: Table sawsRouter TablesJointersShapers

• INCLUDES: Deluxe L-Shaped Push Sticks
• FUNCTION: Provides hand safety while guiding wood for sawing and cutting – allowing you to push the entire workpiece down with a single push stick
• APPLICATIONS: The L Push Sticks (sometimes referred to as V Push Sticks) are commonly used in combination with jointers, tablesaws, router tables and shapers
• CRAFTSMANSHIP: These well crafted woodworking hand safety tools were constructed for long-term durability, and designed with extended heels, additional padding and extra ribs for added structure(Patent pending)
• DELUXE GRIP: This premium pusher tool features a safe, ergonomic handle that’s easy to work with and feels natural in the hand

User questions & answers

Question:	How wide is the Powertec push stick
Answer:	The handle portion is 1” wide and the lower push stick portion is 9/16” wide.
Question:	How good is the quality
Answer:	For the price, I was surprised at the quality of them. They were thick enough for a firm grip and the rubber on the bottom gave it good control.
Question:	How good is the quality
Answer:	They are decently made.
Question:	Is it made in China
Answer:	I no longer have the packaging, but nowhere on the parts do they say they were made in China.

Product description

The dust bag attaches to the dust port and is used to collect sawdust.

1. To attach the dust bag simply squeeze the spring clamp and slide clamp over tabs on dust port and release spring clamp.

2. The dust bag requires emptying when full of sawdust. Empty it frequently and after completion of sawing . Squeeze spring clamp and carefully remove dust bag from dust port .Empty dust bag in proper trash bin by unzipping the bag.

• Dust Collector Bag with Wire Support Frame;
• Helps keep work area cleaner; Collects up to 75% of dust and particles;
• Replaces Bosch part TS1004; Easy to attach and detach to your tablesaw;
• Dimensions: L 31" x W 13.7" head side x W 9.8" end side, D of ring 2.5" up to 2 7/8";
• Can be used with other table saws that have 2-1/2 inch dust ports on the exterior of the saw.

User questions & answers

Question:	how wide is the opening hole
Answer:	No. Make sure your hole saw shank is long enough to pass through the hole of the dust bowl and into the drill chuck. Leave some room so the bowl isn't bound between the two.
Question:	Will this work with a planer
Answer:	I also use plant watering sheilds . This bowl works really well it is made of a soft rubber so if you dont store it properly it will loose its perfect shape it was summer in phx az threw it in back of my truck went to use next day and it was deformed permanently I will order another one but will take better care of it
Question:	Compatible with Chicago Electric
Answer:	I have it hooked up to an old 2703 portable Makita. It only clogs up when it gets full. The air from the blade keeps the bag inflated.
Question:	Is there a lot of clogging up with this dust bag collector
Answer:	Not actually sure it's flexible. It's on my DeWalt plane-notorious for blasting shavings 10+ ft. The bag works perfectly after I made one small tweak. There is an opening in the throat of the attachment point. A big paper clasp closed it. I can't believe how much stuff goes in the bag and how little dust escapes. You'll love it.

Product description

Features:

Fast and accurate measurements as well as zero settings to any position

It is convenient to read with LCD Display

There are Powerful Built-in Magnets on the Base Which Secures the Attachment to Any Iron Surface

Small and light, it is really easy to be carried and used.

HIDDEN MAGNETIC BOTTOM and super-LOW POWER CONSUMPTION

Specifications:

* 62MM  2.44Inch Length

* PC/ABS housing materials

* Resolution: 0.01°

* Horizontal level measuring range: 0 to 360° (4*90°)

* Accuracy: ±0.1° at 0° and 90°, ±0.2° at the rest angles

* Measures angle in ° (degrees)

* Automatic shut-off after 5 minutes

* VA White color digits Screen Display

* Self-checking accuracy

* Auto-reverse reading display

* Set Zero function at any angle

* Self-calibration

* V-groove design on the measurement base, for better measurement of the pipe

* Low battery indicate

* Operated by 2pcs AAA LR03 batteries(included)

* Build-in magnets at the base of measurement

* IP42 dust & water-resistant

* Working temperature: 0~40℃

* Size: 62*30*55MM, Net weight: 65g.

Package Included:

1 x Digital Level Box

2x AAA  batteries

1 x Carry Bag

1 x User Manual

• 【Digital Angle Gauge】The Digital Angle Finder with 0 to 360° (4*90°) measuring range, is designed for measurement in calculated Industries, also working as a true digital level for tight Spots.
• 【High Accuracy】This digital angle finder with V-groove design on the measurement base, for better measurement on pipe, set Zero function at any angle. Accuracy: ±0.1° at 0° and 90°, ±0.2° at the rest angles, 0.01-degree resolution
• 【Built-in Magnets】The level box with a powerful built-in magnet on the base secures the attachment to saw tables, fences, blades, and other metallic surfaces.
• 【Auto Power Off】Digital Protractor is operated by 2pcs AAA LR03 batteries(included) and can automatically Turn Off after 5 minutes of no operation.
• 【LCD Display】the digital angle gauge's values can be clearly and easily Read on the LCD Display. Low battery indicates. Small and light, it's convenient to carry and use.