12 best laser angle finders

• ✨Innovative Design--3 in 1. According to the customer's usage habits and scenes, we have added the laser line function to the traditional inclinometer,Realize the innovation of the integration of 3-in-1 such as Electronic Level & Angle Gauge & Laser Level. And achieved the bottom and back double-sided magnet coverage,make it more widely used.It is the top pick tool for Carpentry, Building, Automobile, Masonry etc. Also, a great gift for father’s day, birthdays, Christmas
• 🎒Re-chargeable and Portable--Small body,Large capacity. With 300 mAh lithium battery and Type-C interface, this product can be charged through devices with USB ports, scuh as PC, laptop, power bank, USB charger and etc. Working hours under full power: 2-3 hours. Besides, the function automatic shut-off after 5 minutes would save power and extend battery life. You can cancel this function manually,1 X Type-C charging cable included
• 📌Two-sided Magnet & IP54. Thanks to its magnets on the bottom and back, this digital protractor would be easily and firmly attached to the metal surface without falling off. You can attach it to miter saws, band saws, table saw blades or any other metal surfaces. No matter where you are, you can always keep the inclinometer within reach. Reaching IP54 dust and water-resistant, this tool can be used in woodshop, garage, or backyard shed and other work environment.
• 💎LCD Dispaly&Screen Adaptive Rotation .This Digital Angle Gauge is equipped with a 1.44-inch LCD display with backlight and the responsive electronic tilt sensor, providing you accurate, immediate and clear measurements. All kinds of related status also will be shown in this screen, such as remaining battery, measuring unit, laser on/off and etc. The screen can be automatically rotated by 4 * 90°, which is convenient for reading numbers under different circumstances
• 📐Absolute measurement &Relative measurement.There are 2 measuring modes to meet different measurement needs: Absolute Measurement (ABS) and Relative Measurement (REF). Just one short press, you can check the true or relative angle conveniently. Besides, featured Data Hold, Unit Conversion, Automatic/Manual Calibration functions, it is definitely a great assistant for a great work. (Pre-calibrated in factory)

User questions & answers

Question:	Does it automatically turn-off in a few minutes
Answer:	yes, units include Degrees, percent, in/ft and mm/M. it seems quite accurate.
Question:	Wont hold chrage overnight. Fully chrarged & next morning wont turn on. Anyone else have this problem
Answer:	The Reference feature allows you to set the current level position as "0"... so yes.
Question:	Do the lasers on both sides always light up at the same time? Can I just turn on one side
Answer:	Yes, works great on steps and other short slopes.
Question:	To what distance will the laser line function accurately
Answer:	Yes, the level comes with a cloth (I believe medium weight nylon) carrying case that has a small strap handle at one end.

Product features

TACKLIFE MDP03 —— 3-In-1 Angle Gauge from Future

TACKLIFE has been committed to researching more innovative tools to facilitate people's lives. We did a lot of market research and product testing, and finally developed this MDP03-Digital Electronic Level & Angle Gauge & Laser Level 3-in-1.

• INCLINATION MEASUREMENT
• LASER MARKING
• LEVEL DETECTION

SPECIFICATIONS

Screen: 1.44 inch LCD

Measuring Range: 4*90°

Display Resolution: 0.01°

Accuracy: ±0.2°

Repeatability: 0.1°

Charging Jack:Type-C

Battery: 3.7V lithium battery 300mAh

Working Hours: 2-3H

Waterproof Level:IP54

Laser Class: Class 2 (IEC/EN60825-1/2014) <1mW Power Output

ERROR Prompt

The product will automatically report an error if the position of the digital goniometer is incorrect (the diagonal is inclined more than 30 degrees)

Type-C interface

With Type-C interface, this product could be charged by most devices that support USB port, such as laptop, PC, power bank, USB charger, and etc.(1 X Type-C charging cable included)

Portable & Compact

Weighs only 106g, this product is compact and portable enough to adapt to various occasions. You could put it in the tool bag, trouser pocket, or even jacket pocket

More extensive applications

Timber Processing/ House Building / Interior Renovation/ Vehicle Repair

Whether you are a beginner or a master carpenter, TACKLIFE would assist you with almost any project.

U-TURN CALIBRATION

1.Place the product at right angle (Step 1), and ensure that the plane is an absolute horizontal plane.

2.Long press the second button to adjust the head adjustment function (Step 2)

3.Press the button to proceed to the next step (the interface is shown as Step 3)

4.Rotate the product 180° in the same position (Step 4) and press the button to complete the calibration

• ▶【Digital Angle Finder Ruler】Measure all your workshop angles, bevel angles, bevel crowns, trims, engineering drawings, square frames, miter saw blade angles. Ideal for carpenters, plumbers, bricklayers and all construction industries
• ▶【Backlit LCD Display】 Come with backlit LCD display which makes it possible to read the data clearly, even under a dim circumstance. With the HOLD design protractor could be locked at any angle for easy reading. Feature the function of automatically shuting off after five minutes without any operation to increase the batteries' life
• ▶【Many Functions' Combination】Digital Protractor equipped with horizontal and vertical bubble can be used as a level ruler to help you check and calibrate. It has windows that project two clear red laser, and the laser angle will change with the extension of the arm, works well for tiling
• ▶【Accurate Measuring Ruler】Designed with two 18-inch easy-to-read ruler with high accuracy and clear scale provide you with better length measurement and line drawing experience, the bright yellow paint appearance contrasts with the black scale for better readability of the value. This digital protractor makes a necessary for the DIY hobbyists or handymen
• ▶【Lightweight Material】Made of lightweight aluminum for carrying with little effort, it is resistant to corrode. Angle Range is 0-236°, Measuring precision: ±0.5°, Increase/Decrease Angle: 0.1°, total length: 600mm, Laser Class:Class 2, Output power:<1mW. If the product is damaged during transportation, please feel free to contact us, we will replace it for free or refund every penny, no doubt.

User questions & answers

Question:	Does this include a digital inclinometer or do you have to rely on the spirit tubes for leveling
Answer:	I did not buy it to hold levels, but it looks like you could only fit 2 levels on top of each other depending on how thick they are. The metal I am storing in the bag is 1"x3" and I can fit 2 in top of each other.
Question:	does it have a on & off button like for reset ? like if you want to 0 it in when its at 90degrees
Answer:	I fit 2 levels in each pocket.

Product features

Backlit LCD Display Design

There is a clear and easy to read LCD screen that will show data for every slight angle change at once, the illuminated screen keeps normal work even on dark light

Hold Button To Lock Angle

If you want to keep the exact measuring results for easy reading, simply press HOLD function button rather than twist the knob to lock

Auto Off

It has a battery display function and will be automatically shut off after 5 minutes of inactivity to saving energy. Comes with 4 button-cells battery standby

OLI Tool Digital Protractor Angle Finder

• LCD Display For Easy Reading
• With Two Accurate 18-Inch Rulers
• Features Horizontal and Vertical Bubble Level
• 2 Laser Line Keep Any Position To Longer Distance
• Data Holding Function to Keep the Measurement Result
• Backlight Design To Keep Its Normal Use in A Dim Environment
• Made of Lightweight Aluminum with Bright Yellow Appearance
• Automatically Shuting Off after 5 Minutes Without Any Operation
• Come with 4 Ready-To-Use Batteries for Reducing Preparation Time

Product description

Bosch GTL2 Laser Level Square Accuracy: Up to 1/2-Inch at 30 Feet; Range: 30-feet; Includes Adhesive Mounting Strips. Projects horizontal and vertical -Inch chalk lines-Inch on any surface. Alignment Guide for 90-degree Layout - Calculate and turn angles in 5-degree increments. Class II laser product, ≤1mW power output

• VERSATILE: The Bosch GTL2 Laser Level Square projects horizontal and vertical chalk lines on any surface up to 30-ft
• VISIBILTY: Bright, sharp, highly visible laser lines to help you square, align and angle at 90° for squaring kitchen tile, bathroom flooring layout, and walls
• CONVENIENT: Features an alignment guide for 90° layout and calculates and turns angles in 5° increments
• USER FRIENDLY: Simple one-button operation powers two perpendicular laser lines (90°) on and off, allowing flooring pros to start kitchen tile or bathroom tile layout quickly
• SECURE: The Bosch GTL2 features an easy-to-press push button that secures the laser tool to smooth surfaces using non-abrasive adhesive, for positing to the surface for a fixed attachment
• Laser Diode: Class IIM, = 1 mW @ 650nm
• ACCURACY: The Bosch GTL2 provides precision and accuracy up to ±1/2-in @ 30-ft while the vials ensure a level tile, so the two laser lines are at an exacting 90° angle

User questions & answers

Question:	does it self level
Answer:	10 amps is 1200 watts of power Power is equal to amps squared times the resistance in ohms
Question:	Can this span 20 feet indoors
Answer:	I son’t recommend this drill for anything. I bought it thinking it was a good deal. When I finally needed to use it, i was drilling several holes into garage 2 X 4’s to mount some shelves. It was so umder powered that after 3 or 4 holes it started smoking. I wqs unable to return it because I had it past the return date. It went into the trash because it could not be returned and was too dangerous to allow anyone else to use it.
Question:	How would I be able to stick this on the wall If I wanted to level some wall art
Answer:	It is 96-in. It folds up for shipment.
Question:	Is the sticky substance that is used to stick the level to the wall reusable? Will it stick to most any wall material
Answer:	The IRWIN 1804139 should hold (2) 78" levels.

Product features

GTL2 Laser Level and Square

The Bosch GTL2 projects horizontal and vertical laser chalk lines to help you square, align and angle at 90 degrees.

Includes: GTL2 Laser Level and Square, Adhesive Mounting Strips

Alignment Guide

Calculate and turn angles in 5° increments for 90° layout.

One-Button Operation

Powers two perpendicular laser lines (90°) on and off.

Two Bubble Vials

For leveling and aligning laser tool and wall.

Get It Right

Projects horizontal and vertical laser “chalk lines” on surfaces.

The Job Just Got Easier

With Bosch laser technology, users are able to be more productive and more profitable – with greater accuracy and precision on the job site. By offering an extensive range of line lasers, laser measures, rotary lasers, point lasers, digital levels, optical levels and measuring tool accessories, Bosch is able to provide solutions for a wide variety of applications. With Bosch measuring tools users are able to work smarter, not harder.

Product description

The Bosch GAM 270 MFL Digital Angle Finder and Inclinometer is five tools in one: a digital angle finder, an inclinometer, a miter cut calculator, a protractor and a digital level. The angle finder provides accurate angle targets, while the inclinometer offers precise measurements in degrees. The tool is also equipped with an integrated laser, allowing the user to transfer inclination measurements up to 100 ft. The tool has two easy-to-read illuminated, flip displays, one for the inclinometer and one for the angle finder. Users are able to easily reuse and transfer save measurements with the hold function. The cut calculator provides easy saw angle adjustments and a compound miter calculator. Users can find the miter angle using the tool's legs, which have an angle range of 0-270°. The compound miter calculator is used to measure joint angles that are not perpendicular. The tool has clearly labeled buttons for straightforward calculations. The angle finder has robust housing with IP 54 protection. Includes: Digital angle finder and inclinometer; Leg Extension; Hard Thermoformed Case; AA 1.5V Batteries.Simple Miter Cut Input Angle Range :0° – 220°

• VERSATILITY: The Bosch GAM 270 MFL provides five tools in one including a digital angle finder, an inclinometer, a miter calculator, a protractor and level.
• MEMORY: This angle finder provides angle memory, to provide the same angle and inclinometer measurements in different areas of the jobsite.
• DISPLAY: Easy-to-read illuminated, rotating flip display for the inclinometer and angle finder. The miter cut calculation has an input measurement from 0-270 degrees..
• DURABLE: Features robust housing with IP54 protection, making the angle finder water and dust resistant.
• COMPLETE: The Bosch GAM 270 MFL includes a 5-in-1 digital angle finder, 24 in. leg extension, hard thermoformed case, 4 AA 1.5V batteries.

User questions & answers

Question:	Is the level and plumb function digital or bubble only
Answer:	No, it is NOT for seeing without turning it around! It is a HEIGHT scale (measures from the TOP), whereas the main scale on the front (white face) is a GRADE scale (measures from the BOTTOM)
Question:	Does it have Bluetooth to send measurements ti the phone
Answer:	Two items were in the small pocket of the carrying case: 1) A replacement release button and a spirt level for plumbing the grading rod to a true vertical for proper measurement. Nice feature not noted in the Amazon ad...I almost ordered a set of spirit levels when I ordered this grading rod; I'm glad I held off until the grading rod arrived. The rod does not come with instruction or care sheet/s...it is pretty straight forward and simple to use. Word of caution: if you should extend the small inner telescoping section first, you will not be able to collapse the section back to the home position until the adjacent section is extended. Once the adjacent section is extended, it will expose a release button that is depressed for collapsing the inner section.
Question:	Any audible tone features I.e. @ Level/plumb or when a stored angle is found
Answer:	this is a fine home-owners drill. That said it is the older brush technology. If the brushes wear the springs will help get the drill operational again. the repair is not necessarily a DYI project.
Question:	this level its magnetic
Answer:	1200 watts is 10 amps

Product features

Bosch 5-in-1 Digital Angle Finder and Inclinometer GAM 270 MF

The Bosch GAM 270 MFL Digital Angle Finder and Inclinometer is five tools in one: a digital angle finder, an inclinometer, a miter cut calculator, a protractor and a digital level. The angle finder provides accurate angle targets, while the inclinometer offers precise measurements in degrees. The tool is also equipped with an integrated laser, allowing the user to transfer inclination measurements up to 100 Ft. The tool has two easy-to-read illuminated, flip displays, one for the inclinometer and one for the angle finder. Users are able to easily reuse and transfer save measurements with the hold function. The cut calculator provides easy saw angle adjustments and a compound miter calculator. Users can find the miter angle using the tool's legs, which have an angle range of 0-270°. The compound miter calculator is used to measure joint angles that are not perpendicular. The tool has clearly labeled buttons for straightforward calculations. The angle finder has robust housing with IP 54 protection.

Product description

The Bosch GAM 220 MF Digital Angle Finder is four tools in one: an angle finder, a cut calculator, a protractor and a level. The flip display is illuminated and rotating, making it easy to read. The simple miter cut calculation has an input range of 0-220°, and it includes a compound cut calculator. It has clearly labeled buttons for straightforward calculations. This angle finder provides angle memory, to provide the same angle measurement in different areas of the jobsite. The tool has robust housing with IP 54 protection. It’s a perfect tool for carpenters, remodelers and contractors. Includes: Digital Angle Finder; Leg Extension; Hard Thermoformed Case; AA 1.5-Volt Batteries

• VERSATILITY: The Bosch GAM 220 MF provides four tools in one including an angle finder, miter calculator, protractor and level.
• MEMORY: This angle finder provides angle memory, to provide the same angle measurement in different areas of the jobsite.
• DISPLAY: Easy-to-read illuminated, rotating flip display. The miter cut calculation has an input measurement from 0-220 degrees
• DURABLE: Features robust housing with IP54 protection, making the angle finder water and dust resistant.
• COMPELTE: The Bosch GAM 220 MF includes a 4-in-1 digital angle finder, 16 in. leg extension, hard thermoformed case, 4 AA 1.5V batteries.

User questions & answers

Question:	Does this angle finder work equally well in any position (like upside down...or, standing on eighter end
Answer:	"displays bevels in degrees, IN/FT, mm/M, percent slope"
Question:	what is the difference between the 220 mf and the 270 mfl
Answer:	The Calculated Industries 7434 AccuMASTER 2-in 1 Magnetic Digital Level and Angle Finder weighs .28 lbs
Question:	What is the absolute accuracy and resolution
Answer:	No real calibration. You can zero it out at any angle, to get the difference from one position to the next . or it will show you level
Question:	Es magnetico
Answer:	Because you want to first zero it ideally from your table saw's steel or cast iron insert plate, or if you don't have that, cast iron top. The magnetic base helps a great deal to prevent tilting the instrument when pressing the zeroing button. Making your measurement without first zeroing only will be accurate if: A. your table is perfectly level to within 5/100s of one degree (very unlikely unless NASA or JPL made the floor of your shop and calibrated your saw), B. your insert plate is perfectly level, C. your 7434 arrived (probably from thousands of miles away after weeks or months inside a shipping container that resulted in large temperature, humidity, and atmospheric pressure fluctuations) with a perfect calibration, AND D., your 7434 has never sustained an injury that will alter its accuracy by more than 1/1000. In other words, only a fool would use this before zeroing, and that zeroing should be done on your table every time before you measure the present angle of your blade. Therefore, the magnet is in the correct location, and a second magnet would cause problems. And the magnet is NOT weak. That's BS. In fact, it is significantly TOO strong and easiky causes jarring impacts that disables the 7434.

Product features

GAM 220 MF Digital Angle Finder

The Bosch GAM 220 MF Digital Angle Finder is four tools in one: an angle finder, a cut calculator, a protractor and a level. The flip display is illuminated and rotating, making it easy to read. The simple miter cut calculation has an input range of 0-220°, and it includes a compound cut calculator. It has clearly labeled buttons for straightforward calculations. This angle finder provides angle memory, to provide the same angle measurement in different areas of the jobsite. It’s a perfect tool for carpenters, remodelers and contractors.

Includes: GAM 220 MF Digital Angle Finder, Leg Extension, Hard Thermoformed Case, AA 1.5V Batteries

Four Tools In One

Angle finder, miter calculator, protractor and level.

Illuminated Flip Display

Provides better readability and ease of use.

Measuring Accuracy

Accurate angle measurement of +/- 0.1°, from 0° to 220°.

Robust Housing

Protects against dust and water.

The Job Just Got Easier

With Bosch laser technology, users are able to be more productive and more profitable – with greater accuracy and precision on the job site. By offering an extensive range of line lasers, laser measures, rotary lasers, point lasers, digital levels, optical levels and measuring tool accessories, Bosch is able to provide solutions for a wide variety of applications. With Bosch measuring tools, users are able to work smarter, not harder.

Product description

General Tools 823 Digital Angle Finder Rule, 10-Inch

From the Manufacturer

This angle finder combines the ruggedness of analog rulers, both standard and metric, together with the digital technology needed for complete accuracy when measuring inside, outside and reverse angles. Precise measurements prevent waste by facilitating exact miter cuts. One button activates the reverse angle function, a hold button digitally saves the measurement and the large ergonomic locking know saves the angle manually. A big LCD readout makes measurements extremely easy to read while an innovative center CHECK notch enables exact ruler placement marking. This angle finder is ideal for framing, custom furniture building, stair and patio construction. flooring, tiling and many woodworking, carpentry and contractor needs in the shop and in the field.

GENERAL TOOLS - THE PRECISE TOOL FOR DOING THE JOB EXACTLY RIGHT. Offering over 1,000 tools, we’re proud to provide tradesmen, craftsmen and DIYers around the world with a broad range of affordable, specific-purpose mechanical hand tools and precision measuring and inspection tools.

For inquiries, please contact our Customer Service Department at 212-431-6100. We strive to provide our customers with 100% satisfaction.

WORK SMARTER, MEASURE BETTER & BE MORE PRODUCTIVE WITH GENERAL TOOLS

GENERAL TOOLS - THE PRECISE TOOL FOR DOING THE JOB EXACTLY RIGHT. Offering over 1,000 tools, we’re proud to provide tradesmen, craftsmen and DIYers around the world with a broad range of affordable, specific-purpose mechanical hand tools and precision measuring and inspection tools.

For inquiries, please contact our Customer Service Department at 212-431-6100. We strive to provide our customers with 100% satisfaction.

WORK SMARTER, MEASURE BETTER & BE MORE PRODUCTIVE WITH GENERAL TOOLS

• PREVENT WASTE- This digital 10” stainless-steel ruler and angle finder combination tool makes precise, easy and fast measurements
• LOCK IT AND REVERSE IT- Digital protractor has lock and reverse angle functions. Place the angle rule where you need to measure your next cut, LOCK it in place with knurled locking nut, make a mark and use your miter saw to make your cut. The angle finder will automatically display the reverse angle
• MEASURE 360-DEGREES- Hinge mechanism on the angle rule allows a full range of 0 to 360-degrees to measure inside outside and reverse angles, accuracy +/-0.3 Degrees. Center check notches are on the ruler ends enables exact ruler placement marking. Display has a hold function to freeze movement for accuracy
• PICK YOUR ZERO POINT- Woodworking tool can be zeroed at any point in the swing plus the display can be inverted for easy reading
• LARGE LCD DISPLAY- Easy to read LCD display eliminates guessing or eyeballing the angle and length with one convenient protractor tool

User questions & answers

Question:	Does it reset to zero when turned off
Answer:	The angle finder is digital of course and It could be use as a digital inclinometer depending of how you use it horizontal or vertical. You will have to relay on the level spirit tubes it has to find level when measuring angles in any direction. Hope this answers your question.
Question:	what battery type is required
Answer:	On off button.........yes It shows 90. ......not 0.
Question:	Does it come with a case ? If so, hard or soft
Answer:	Select Amazon return
Question:	Does this allow for the portion with the digital readout to spin around continually/round robin style? Or does it stop turning at the 359.9 deg point
Answer:	No it’s in tenths of feet.

Product description

The ToolSmart Digital Angle Finder quickly determines the angle of any corner. This tool is especially useful for crown moulding and flooring applications to make sure you get perfect cuts every time.

INCLUDES - “CR2032” battery and user’s manual

SPECIFICATIONS:

Measurement Range: 0 to 225 degrees

Measurement Accuracy: ±0.3 degrees

Resolution: 0.1 degrees

LCD Screen Size: 1.6 in. diagonal

5-minute Auto Power Off

Operating temperature of 32° to 104°F (0° to 40°C)

Powered by non-rechargeable CR2032 battery (included)

GENERAL TOOLS - THE PRECISE TOOL FOR DOING THE JOB EXACTLY RIGHT. Offering over 1,000 tools, we’re proud to provide tradesmen, craftsmen and DIYers around the world with a broad range of affordable, specific-purpose mechanical hand tools and precision measuring and inspection tools.

For inquiries, please contact our Customer Service Department at 212-431-6100. We strive to provide our customers with 100% satisfaction.

WORK SMARTER, MEASURE BETTER & BE MORE PRODUCTIVE WITH GENERAL TOOLS

• The ToolSmart Digital Angle Finder accurately determines the angle of any corner, easily determine the angle of any corner up to 225 degrees
• This digital protractor tool is especially useful for crown moulding and flooring applications to make sure you get perfect cuts every time
• Easily send inside and outside angle measurements to your smartphone with one click and quickly figure out compound angles with the ToolSmart App
• Using the ToolSmart App, you can also quickly and easily determine the materials and tools you will need to complete your project
• This next generation miter finder and angle measurement tool also incorporates a 10.5 in. ruler and horizontal & vertical bubble levels

User questions & answers

Question:	Is General the Harbor Freight brand
Answer:	Thank you for your question. The GTL2 does not self level. If you have further questions please feel free to contact our Bosch Customer Service Representatives at 1-877-BOSCH-99 (1-877-267-2499)
Question:	Doesn’t pair with IPhone
Answer:	I just completed a 20x12 kitchen floor tile. It works well for the 20ft length. But bumpy surface certainly won't help the situation. So, you do need to position the laser a bit higher than the tiles so the whole length can be covered. Just keep in mind that the laser is just to help for the planning. I did used a level to make sure the tiles were lined up straight, even I have the laser guided me.
Question:	Will it display rise/run or just degrees
Answer:	It comes with a type of sticky clay or substance that allows you to stick it to the wall.
Question:	Are the edges of the ruler sharp like some of the other ones I have purchased on Amazon
Answer:	Thank you for your question. Yes, the adhesive putty is reusable. Eventually it will not stick as well so it will need to be replaced with new non-abrasive adhesive putty. It will hold securely on most smooth surfaces. If you have further questions please feel free to contact our Bosch Customer Service Representatives at 1-877-BOSCH-99 (1-877-267-2499).

Product features

Find The Angle Of Any Corner For Better Cuts

The ToolSmart Digital Angle Finder quickly determines the angle of any corner. This tool is especially useful for crown moulding and flooring applications to make sure you get perfect cuts every time.

• ▶2 IN 1 Functions Combination Digital Angle Protractor - Versatile angle measurement tool doubles as both a digital angle protractor and a ruler for measuring all your workshop angles, bevels, miters for crown, trim, drawing, squaring frames, woodworking, setting miter saw blade angles and more.
• ▶High Accuracy & Durable Material - Made of high quality stainless steel and laser etched. Thickened and widend ruler supports measurement between metric(mm) and imperial(inch), makes it can measure length (0~400 mm/0~7 inch) convenient and accurately. It is a good choice for most projects and daily use.
• ▶LCD Display & Locking Function Easy to Read - Protractor comes with a large easy-to-read LCD display(Accuracy: ± 0.3 º; Resolution: 0.05°), and has lock and reverse angle functions, hinge mechanism allows a full 360-degrees to measure inside outside and reverse angles measurement, measured value is stable and reliable.
• ▶Easy Operation and Measurement - Are you tired of tedious operation steps? Our digital angle finder tools is designed with 2 press-buttons and hinge mechanism to make it easy for everyone to use, which lets the measuring faster and save your precious time, a good choice for family DIY projects, woodworking, decoration, machining.
• ▶Power Aupply & Safely Packaging - 3V CR2032 (included), large capacity standby with automatic power-off function, can work more than 2000 hours, saving power consumption and extending service life. Comes with an exquisite plastic box packaging, easy to carry and store safely, protect the protractor from damage, and extend the service life of the protractor.

Product features

Why Recommend OLI Construction Protractors To You

• 2 IN 1 versatile angle measurement tool doubles as both a digital angle gauge and a protractor for measuring. Easy to read LCD display eliminates guessing or eyeballing the angle and length with one convenient protractor tool.
• The OLI Protractor saves time and reduces waste. Its ideal for carpenters, plumbers, and all building trades that require the measuring and transferring of angles. It is the perfect and essential companion for every user, it would be your better choice!

According to the customer's feedback, we provided instructions and solutions, thank you :-)

• Q1:About the protractor does not work normally after the battery is reinstalled.
• A1:Dear customer, it is not damaged and can continue to working, after reinstalling the battery, Err appears on the screen, you only need to press the ZERO button to use it normally. Thank you :-)
• Q2:About every time zero it, when return to the original value it's different compared with original.
• A2:Dear customer, it is not damaged and can continue to work. This is how it works: when you zero it at any angle, the protractor will be based on the current position and then recalculate the angle. For example: when you zero it at 45°, and then return it to the original position, it will be displayed 0° to 45° instead of 0°; If you do not zero and then return to the original position, it will be displayed 45° to 0°. Looking forward to your understanding, thank you :-)

Large Capacity Standby & Large LCD Display

• 3V CR2032 (included) Large capacity standby with automatic power-off function, can work more than 2000 hours, saving power consumption and extending service life. With LCD display for reading measurements easily.

High Accuracy & Durable Material Ruler

• Made of high quality stainless steel and laser etched, thickened and widend ruler ensure years of using, supports measurement between metric(mm) and imperial(inch), a good choice for most projects and daily use.

Exquisite Box Packaging & Easy to Store Safely

• Comes with an exquisite plastic box packaging, easy to carry and store safely. Avoid scratching the protractor and other tools, protect the protractor from damage, and extend the service life of the protractor.

• Aluminum Alloy
• ◆Premium Material - Our 6-sided angle measuring tool is made of 5mm aluminum alloy with metal knobs and bolts, more durable and sturdier, won't break from bending or rusting. The scale is laser engraved, super wear-resistant can be used for a long time, no need to worry about corrosion. Angle finder tool can meet all your home or professional project demand
• ◆Accurate Angle Measurement Tool - The six-sided angle tool is laser engraved marking(inches & centimeters) perfect for precise and accurate angle measurements. With the 6-part carpenter tools, you can adjust the drilling position to mark tiles exactly. Metal protractor angle finder is an ideal measuring tool and integrated hole positioning
• ◆Easy to Use & Increase Efficient - Use the 6 folding rulers to quickly measure the angle and size, lock the angle ruler in shapes, patterns, and templates to copy the imprint and draw the perfect angle. The innovative, six-sided template tool can be used as a stencil for cutting your workpiece. Saving you time and improving your work and productivity
• ◆Portable & Easy to Store - These angle measuring ruler tools are lightweight designed for handy use and be folded for easy storage. A must having tool in your box. Easily folded and carried to your next project, helps speed up the process of making those funky cuts. Instead of slowing down to make a template, you can use this gadget
• ◆Wide Applications - Our universal layout tool is suitable for creating bull eyes, arches, plumb cuts and any projects that you can think of, works great on carpentry, brick, tile, wood, woodworking, glass, flooring, tiles, stone, laminate, construction & engineering projects and much more. It's a perfect template tool for bricklayer, craftsmen, handymen, DIY-ers. This is also the best choice as a birthday gift, Christmas gift and any other festival gift, get one for your father, boyfriend

Product features

Are you looking for a multi angle measuring ruler that is easy to use? Our angle ruler will be a good choice for you.

• Portable, lightweight and foldable for easy carry, made of sturdy premium aluminum alloy, used for very long time.
• With both CM & IN by laser etched marking. Clearer and more precise to use, meeting your different needs.
• A universal layout measuring tool while working in tiles, brick pavers, lumber, laminate, wood, flooring project and more.

OurWarm Measuring Tools for Carpentry

• Included Package:

1 x 6-Sided Multi Angle Measuring Ruler

1 x User Manual

• Single Ruler Length: 6.89 inch/175mm
• Material: 5mm Aluminum Alloy
• Color: Black
• Measurement Accuracy: 1mm
• Measurement System: Centimeter & Centimeters
• Style: Molding angle finder

• Shape: Can Be Freely Deformed
• Subject Matter: Measuring & Layout Tools
• Intended Use: Marking Lumber, Angles for Paver Bricks, Spacing and Gauging

Highly Versatile

The folding ruler slides and locks into any desired angles to save you time on repetitive measurements. The chute structure in the back supports the perfect sensitivity and accuracy for sliding to any angle and sharp you desired.

Design with tile hole locator

Upgrade with drill guide locators design, corner angle finder could help mark the position and drill the hole on tile which you need.

Clear Scale and Laser Etched Marking

The scale number is etched by laser, it is clearer and more precise than the painting one, and it can last longer for the mark can’t be wiped.

Perfect Thickness

Our ruler is much thinner than other rulers with the same material. It can be put in your toolbox and not occupy extra space.

How to Use

1. Place the tool on any surface and then adjust the six straightedges to the desired shape.

2. Tighten the high-grade metal screws to fix the angle.

3. Move the definite-shaped ruler onto the tile or something else and use the locator to find the place you need to slot.

4. Put the tile onto the wall after slotting.

Shape Measurement

The angle of the ruler can be adjusted, the nut can be tightened to fix the angle, and the profile measurement can be smoothly performed to avoid the variation during measurement and ensure the accuracy of the measurement.

Portable and Versatile

This foldable angle ruler easily folded and carried to your next project, helps speed up the process of making those funky cuts. Instead of slowing down to make a template, you can use this gadget.

Wonderful Gift

This multi angle ruler will be a great New Year gift or birthday gift especially for someone who loves DIY. The ruler's accurate measurements will save you from spending tons of money on wasted material and paying a professional.

Product description

The Bosch BLAZE Outdoor GLM400CL Connected Laser Measure with Camera features a 5.0 megapixel, adjustable zoom camera to find the laser spot in bright conditions, measuring up to 400 ft. Transfer the measurement documentation to a smartphone or tablet with Bluetooth using Bosch’s Measure On app. Note: Photo files are too large to transfer. The outdoor laser measuring device provides default real time length, length, area, volume and indirect measuring functions – which are simple to take advantage of thanks to the display guide walking through each measurement process. A built in inclinometer determines the angle of pitch and confirms when the tool is level. The laser measure also features an easy to read backlit color display, reinforced screen glass, an easy to use display guide and 11 measuring functions (including default real time measuring). It allows users to see the last 50 measurements on the tool and stores over to 600 images. Class II laser product, <1mW power output

• BLAZE OUTDOOR TECHNOLOGY - outdoor laser measuring device with up to 400 Ft. measuring, camera and next-gen connected convenience through the free Bosch MeasureOn app
• MULTIPLE MEASURING FEATURES – includes 11 different measuring functions, including real time length, length, area, volume, indirect functions, and addition/subtraction capability
• CAMERA – features an adjustable zoom to locate the laser spot at far distances, even outdoors or in busy backgrounds
• ACCURACY AND LONG RANGE MEASURING - provides accuracy up to 1/16 in and measures up to 400 ft
• Class II laser product, <1mw power output
• EASY-TO-READ - backlit color display illuminates numbers in dark areas with distinct resolution, allowing work in low-light or no-light conditions

User questions & answers

Question:	Can you set the precision of the measurements? As in I want to round the dimension to the nearest 1/16" instead of down to
Answer:	just charge it for 0.5-1hour, then will be fully charged
Question:	Can a second floor wall measurement be made accurately while standing at ground level
Answer:	Yes, press button with end on walll and the distance shows on the screen.
Question:	Would this be a good choice outdoors under the shade of trees & less than
Answer:	Yes,it is USB charging, and a USB charging cable included,very convenient.
Question:	Miden en metros
Answer:	commonly full charged in 1 hour.

Product description

Technical Specifications

Material: Angle Finder Tool made of stainless steel

Folded length: 220mm/8.5inch

Length scale: 0~7inch; 0~400mm

Measuring angle: 0~360 degree

Resolution: 0.05°

Accuracy: ±0.2°

Repeatability: 0.05°

Battery: 3V CR2032 (supplied)

Features

Durable Stainless Steel Body: Comes with perfect quality stainless steel,etched measurement provides lifetime clear reading.

Convenient locking knob: The tight/loose knob works well and you can set it to the tightness that suits your use.

Zero Setting: Press zero button at any time to zero the display. Use to measure relative angles easily.

Large HD LCD Display: Large LCD display. Remove PROTECTIVE FILM on display before use.

Battery: 3V CR2032 (included), large capacity standby with automatic power-off function, can work more than 2000 hours, saving power consumption and extending service life.

Applications

Use sturdy angle finder rule to measure angles and lengths and to draw lines

Commonly used in staircase construction and repair, tiling, flooring, crown molding, miter cuts, cutting of base boards and skirting boards

Handy tool for plumbers, woodworkers, carpenters and contractors

• 【2 in 1 Digital Angle Ruler】Anytrp protractor angle finder has the function of steel ruler and angle measuring tool.Digital stainless steel ruler and protractor combination for easy measuring inside and outside angles. Ideal for use in woodworking,construction,or drawing
• 【High Accuracy & Stainless Steel Body】Accuracy of this digital protractor is ±0.2 degree.Folded length 7.5 inch/220mm,total length 400mm.This stainless steel protractor angle finder features laser-etched metric and imperial measurements on ruler edge,comes with a large LCD display for easy reading
• 【Measure 360 degrees & Hold Function】Hinge mechanism on the angle rule allows a full 360-degrees to measure inside outside and reverse angles.With hold function to store measured angle in memory and zeroing button to reset angle finder tool at any time
• 【Locking Function】For read it easily, this woodworking tool could be locked at any angle.Center check notches are on the ruler ends enables exact ruler placement marking.It also comes with a Reverse Function Button, When you measuring large angle and doing reverse measurement,the display could read up-side-down
• 【Wide Application】Doubles as both a digital angle gauge and a protractor for measuring all your workshop angles.Many uses like checking angle of blade on table saw or accuracy of miter saw, making angle cuts or measurements, trim or wall angle measuring. Great gift for woodworker, constructor DIYers etc

Product description

This highly accurate digital angle finder offers easy-to-read measurements via a large LCD display and has an 8" stainless steel blade and steel locking knob. It is ideal for measuring, storing and transferring inside and outside angles when building cabinetry, furniture and picture frames.



The General Tools 828 Digital Sliding T-Bevel Gauge & Digital Protractor in One offers pioneering technology that takes the guesswork out of angle duplication and eliminates the problems associated with manual measurement transfer.



DETAILS:

• Large LCD
• Four control buttons provide five functions: Power on/off, Reading hold, Read reverse angle, Flip display, Clear readout
• Auto power off
• Stainless steel blade
• Impact-resistant ABS handle
• Power source: "CR2032" Lithium-ion battery (included)

SPECIFICATIONS:

• Range: 0 to 360°
• Accuracy: ±0.3°
• Resolution: 0.05°
• Blade length: 8 in.

GENERAL TOOLS - THE PRECISE TOOL FOR DOING THE JOB EXACTLY RIGHT.



Offering over 1,000 tools, we’re proud to provide tradesmen, craftsmen and DIYers around the world with a broad range of affordable, specific-purpose mechanical hand tools and precision measuring and inspection tools.



For inquiries, please contact our Customer Service Department at 212-431-6100. We strive to provide our customers with 100% satisfaction guaranteed.



WORK SMARTER, MEASURE BETTER & BE MORE PRODUCTIVE WITH GENERAL TOOLS

• DURABLE - Commercial grade digital sliding T-bevel and digital protractor with impact resistant ABS handle
• HOLDS MEASUREMENTS- on digital angle finder for transfers between different surfaces or jobs
• TRANSITIONAL DISPLAY - Digital angle gauge has a reverse display button and flip display button with a locking knob for manual measurement transfer. Full LCD display with large digital angle readout.
• AUTOMATIC SHUT-OFF- feature that preserves battery life of the woodworking tool
• DUAL APPLICATION - T-bevel/digital protractor combo- is made with an ergonomic impact resistant handle with 8-inch stainless steel blade used for taking measurements

User questions & answers

Question:	Hi, can i make some reset? the read its not logical
Answer:	Yes
Question:	Can you tighten down the t-bevel to hold the angle
Answer:	Hi Jesse. I'd have to say yes. It does read down to 0.1 degrees (1/10th of a degree) I find it easy to zero out (long press on the 'On' button), and can even rev. the display, from 45 degrees, to 135 degrees. Which I often do. The battery lasts an extremely long time, though I do keep a few spares. Others have complained about the knob, moving the displayed reading while tightening it on the angle to be read. But as you may likely already know, the key here is to just simply keep the knob snug enough to stay, yet just loose enough to move to the angle you are trying to find on your block of aluminum, or whatever. I use it most often on bending polished ornamental metals, and do need to land on 1/2 degree increments from time to time. I Love this thing!
Question:	Can this be used to set accurate angles on table and miter saw blades
Answer:	theres a button opposite the battery I guess that aids in opening the battery holder. I just ooch it in enough to break the connection and make it turn off
Question:	What kinda battery goes in here? I am on a remote island and damn... i overlooked the 'yes' in the product info
Answer:	On the metric side of the ruler close to the read out display push the little tab and battery compartment should slide out on the opposite side , battery installation + side down , takes one CR 2032 battery.

Product features

Digital Sliding T-Bevel & Digital Protractor in One

The Digital Sliding T-Bevel Protractor can measure, set and transfer interior and exterior angles quickly and accurately. This tool is ideal for measuring, storing and transferring inside and outside angles when building cabinetry and furniture, creating picture frames, installing tiles and more.