12 best led dimmer switchs

• 3-Way Single Pole Compatible Slide control dimmer.If UP is off(DOWN is on) after wiring, try switching around the two red wires to reverse the on/off direction
• Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	Where is it made? USA
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	I doubt it, but contact mfg., they are very responsive.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	Check the display is ON or OFF on the top left connor, it should show ON then the device can work.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	What I think was being asked is if this meter can tell you the PEAK load during the time it was connected. For example, let's say it was connected to a refrigerator for 10 hours. Let's say that during that 10 hours the load in Watts was 150Watts. But, when the compressor kicks in, it surges to 2000Watts for 3 seconds. Will this device allow you to see that 2000Watt PEAK later? Does it store that PEAK load into memory so you can view it?

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Product description

The Leviton toggle slide universal dimmer provides smooth, slide-action, full-range dimming for dimmable LEDs, dimmable CFLs, incandescent and halogen bulbs. For a traditional home, the classic style offers the ideal way to upgrade the functionality without compromising the character of the decor.

• Classic design with toggle switch and integrated linear full-range slide control for easy, precise operation
• Designed specifically for dimmable LED and CFL bulbs; Also compatible with incandescent and halogen bulbs
• Single pole or 3 way capable when used with a 3 way switch. No removal of fins required for multi-gang installations
• Built-in starting technology for CFL bulbs; Allows users to modify the dimming range to optimize low light level performance when required (optional)
• Wider dimming range for LED and CFL bulbs than traditional incandescent dimmers

User questions & answers

Question:	Will this dimmer stand 12 AR111 12Watts each
Answer:	Dimmer will control 300 watt dimmable LEDs if the AR111s you have are dimmable 120V 12Watt lights then switch should be OK as 12 lights would be ~144 Watts
Question:	We were trying to connect this switch, the light is on but the dimmer is not working, its a single pole, what am I missing
Answer:	You need to be using "dimmable" bulbs, either incandescent or LED, but not fluorescent. If you are using dimmable incandescent or LED bulbs, I believe there is a slider control (switch) somewhere on this switch to choose either incandescent or LED. That needs to match your bulb type.
Question:	I installed the switch as well as dimmable led bulbs. they work on the dim setting but they blink from half all the way to full power, any ideas
Answer:	I've had similar issues and took it up with Leviton on their website. They initially just asked me to send it back to them, but I stopped short stating that I didn't particularly want to "finance" that. So they did send me a replacement unit and a prepaid shipping label. The replacement one is "better", but sometimes it still goes into flicker or as I call it "spazz" mode. They have asked me for the exact bulbs I'm using (Ecosmart Classic Glass Bulbs from Home Depot) but nothing further from them. I use those same bulbs in (2) other fixtures with Lutron LED dimmers (Model# TGCL-153PH-WH and Model# CTCL-153PR-WH) and they both have worked flawlessly for about a year. Never a single flicker. Bob
Question:	Where is the locator light
Answer:	Mine has a green LED at the top of the toggle switch. It is almost impossible to see in the light, but when the room is dark, it is visible without being disturbing. It comes defaulted to OFF. There are two micro switches on the front of the switch, which are hidden once that switch plate is put on. The top switch has an A and B position. A (the default) is for LED and incandescent lights. B is for CFC bulbs. A second switch, lower down, is for the locator light. Set the switch to ON if you want to use the light. Set these switches before you put on the switch plate because the plate covers these switches.

Product features

Leviton TSL06-1LW Toggle Slide Universal Dimmer

Leviton’s TSL06 Toggle Slide universal dimmer is engineered to provide homeowners optimal control of 300-watt Dimmable LED and CFL bulbs, and 600-watt Incandescent and Halogen bulbs. This new dimmer offers the energy-saving benefits of dimming without sacrificing performance or the time-honored design valued in traditional homes. The Toggle Slide universal dimmer addresses performance issues–such as flickering, reduced dimming range, and low level start up–often experienced when incandescent-only dimmers are paired with dimmable LED or CFL bulbs.

Great Dimming, Traditional Style

The Toggle Slide universal dimmer features an on/off preset function which preserves the selected dimmer setting, smooth start-up, gentle-touch control, and fluid slide movement for precise dimming. The device’s traditional aesthetics offer the ideal way to upgrade functionality from standard switches without compromising the character of your traditional decor. Its slim, compact housing fits easily into a standard wall box and is suitable for multi-gang installations. The Toggle Slide universal dimmer is compatible with Leviton’s complete line of signature Decora wiring devices and wall plates.

Advanced Features

The Leviton Toggle Slide universal dimmer features a microprocessor control which offers the flexibility to fine-tune LED and CFL bulbs for best performance. A “kick-start” setting is available to ensure start-up of CFL bulbs. The dimmer also features a soft green LED locator light built into the switch, making it easy to find in a dark room.

About Leviton Dimmers

Leviton is a leading manufacturer of dimmers designed for both the energy-saving benefits of dimming and the ambiance that can be created in any room of the home by controlling lighting levels. To ensure superior performance, Leviton works with bulb manufacturers to develop dimmers that are tested and proven effective to function in harmony with the latest bulb innovations. Leviton dimmers come in a wide range of models including digital, wireless, preset, slide, rotary, toggle, and touch and provide precise dependable control.

Product description

Lutron Ariadni dimmers are a simple and inexpensive way to add ambiance to any room in your home, while saving energy and extending bulbs life. This dimmer is designed to replace or match your traditional toggle style switches. The discreet slider next to the toggle switch adjusts the brightness of the bulbs to a desired level, while the toggle switch turns the light off and on to your favorite preset level. Designed with a shallow 1 inch deep back cover for easy installation, Ariadni and Toggler dimmers work with your existing traditional opening wall plates. Coordinating Facade screw less wall plates and accessories sold separately.

• Provides the best dimming performance for LED bulbs(compatible with 800+ bulbs- for more specific details view "technical specification" below)
• Also works with ALL incandescent and halogen bulbs
• Works with up to 150 Watts of dimmable LED/CFL bulbs or 600 Watts of Incandescent/Halogen bulbs
• Can be used in Single-Pole or 3-Way applications
• Toggle switch turns lights on/off and returns light to preset level, slider dims and brightens
• Includes Lutron Toggler LED+ (formerly C.L) Dimmer Switch; coordinating wallplate sold separately

User questions & answers

Question:	Is this considered triac based (forward phase control or leading edge) or 0-10v switch
Answer:	The AYCL-153P is a triac based dimmer rated for 150W of compatible LED/CFL or 600W of incandescent/halogen lighting. For compatible LEDs with this dimmer, or another Lutron dimmer, please visit www.lutron.com/ledfinder or www.lutron.com/ledtool.
Question:	do I need two of these switches in a 3-way application or can I use one dimmer with a normal 3-way on the other end
Answer:	Lutron does not recommend two AYCL-153P-WH dimmers in 3-way application. The second location would need to be a standard 3-way mechanical switch.
Question:	Can you fit three of these switches side by side in a standard 3 gang box
Answer:	The switch generates heat so it has tabs on both sides to prevent you from mounting them side by side without being aware that you have to "derate" them if you want to install them side be side. In other words, you can put 600 watts of incandescent bulbs on one dimmer if you mount it alone but only 500 watts of incandescent on a dimmer with one side tab removed (you remove only the tab(s) that overlap) and only 400 watts load with both tabs removed (as you would do mounting 3 switches in a standard 3 gang box). They also include a chart for derating when you mix CFL/LED bulbs with incandescent.
Question:	Anyone know the difference between the "Ariadni" switch (AYCL-153P) and the "Toggler" switch (TGCL-153P
Answer:	I was wondering this exact same question, so I called Lutron and learned that they're the exact same switch. The model numbers differ because they're marketed/sold differently (e.g. Home Depot vs. other stores). So, if you find one cheaper than another, as I've done here on Amazon, buy the less expensive one!
Question:	Where is it made? USA
Answer:	HI，Customer， It is Made in China, UL listed
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	Yes, these are standard size switches. Home Depot or Lowes should have multi-gang plates.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	I doubt it, but contact mfg., they are very responsive.

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Cutting Edge Technology

Our patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Fast and Easy Installation

All you need to replace your existing switch or dimmer is about 15 minutes, 3 simple steps and 1 screwdriver

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

Product description

Lutron LED+ dimmers provide the best dimming performance for LED bulbswhile setting the right light level to improve mood and ambiance for any activity. Designed specifically for dimmable lads and CFL, as well as for use with traditional incandescent and halogen bulbs, they greatly improve the dimming performance when compared to standard dimmers. Featuring advanced circuitry designed to alleviate common challenges, like flicker and pop on, LED+ dimmers are compatible with 800+ bulbs- for more specific details on compatible bulbs, view "technical specification" below. The Diva dimmer matches existing decor a style switches and fits in a standard decor a style wall plate (CW-1-WH). It features a large paddle switch that turns the lights on/off and returns them to your favorite preset setting, along with a discreet slider that brightens or dims the lights to suit any activity.

Create the perfect amount of light while utilizing the latest energy-saving technology with the Lutron Diva C•L Dimmer. Designed for use with 150-watt dimmable CFL or LED lights, the Lutron Diva C•L dimmer features a large paddle switch that automatically returns to your favorite pre-selected light level, a discreet slider to adjust light levels, and a sleek, modern wallplate.

Diva C•L Dimmer At a Glance: Dimmer works with most dimmable CFL/LED bulbs, as well as incandescent and halogen bulbs Slider for precise light control and paddle switch for easy on/off HED technology improves the performance of dimmable CFLs and LEDs over standard dimmers Adjustment dial to set bottom of dimming range for your bulb type Single-pole and three-way applications One-year limited warranty; UL-listed for a broad range of dimmable CFL/LED bulbs

Adjustment dial fine tunes dimming range for your specific bulb.

The C•L Dimmer works with a combination of CFL, LED, halogen, and incandescent bulbs and can be used on the same circuit.

Precise Light Adjustment with Slider

Whether you're reading, watching TV, entertaining, or enjoying a romantic dinner, the Lutron Diva C•L Dimmer lets you choose the right level of light for your activity. It's easy to make subtle adjustments using the discreet slider next to the large paddle switch. When you use the paddle switch to turn lights off and on, it defaults to your preferred lighting level.

Works with Dimmable CFLs and LEDs for Increased Energy Savings

The Lutron dimmer works with dimmable CFLs and LEDs up to 150 watts, a great energy-efficient alternative that can last up to 10 times longer than incandescent bulbs. Plus, by using less electricity, theses bulbs help protect the environment by reducing the amount of carbon dioxide released into the air.

HED Technology for Enhanced Performance

Thanks to Lutron's HED technology, this dimmer actually improves the performance of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, ensuring lights stay on when they are dimmed to a low level, and making sure lights operate properly at all levels. Lights will stay on even during voltage fluctuations, which can happen when a device like an air conditioner or a hair dryer is operated nearby. For safety, the dimmer is UL listed for a broad range of dimmable CFL and LED bulbs.

Compatible with Other Lightbulbs and Mixed Loads

For added functionality, the dimmer also provides full-range dimming for halogen and incandescent bulbs. There is an adjustment dial to set the low end of dimming range for your bulb type for most efficient operation.

The dimmer also works with a mixed load of light sources, so a combination of CFL, LED, halogen, and incandescent bulbs can be used on the same circuit. It can be used for single-pole and three-way applications.

Fast and Easy Installation

Installation is easy--just replace your existing light switch with the Lutron Diva C•L Dimmer and install in less that 15 minutes. A modern wallplate--with no visible screws--blends into the surrounding wall for a subtle finishing touch.

The Lutron Diva C•L Dimmer is backed by a one-year limited warranty.

What's in the Box

Dimmer and screwless wallplate.

Set the perfect mood lighting for any room with the Diva C•L Dimmer.

From the Manufacturer

Control the next generation of lighting with Lutron's dimmable C.L dimmers! Screw-in dimmable compact fluorescent lamps (CFLs) and screw-in dimmable light emitting diode lamps (LEDs) are a great energy-saving alternative to incandescent or halogen light sources; however, dimming them may be difficult. Lutron's new dimmers with HED Technology provides a solution to alleviate your dimmable CFL and LED dimming challenges, while setting the right light level to improve mood and ambiance. The Diva dimmable CFL/LED dimmer with HED Technology features advanced dimming circuitry that is designed for compatibility with most high efficacy light bulbs. With the same features as Lutron's Diva dimmer, the large paddle switch turns the light on/off and returns to your favorite setting. The discreet slider adjusts the light level to suit any activity. These dimmers improve the dimming performance of dimmable CFLs and LEDs compared to standard dimmers. Lutron dimmers with HED Technology also provide full-range dimming for halogen and incandescent bulbs, ensuring today's dimmer is compatible with tomorrow's light sources. The dimmer can even dim a mixed load of light sources (i.e. LED and halogen or CFL and LED bulbs on the same circuit).

• Provides the best dimming performance for LED bulbs(for list of approved LEDs, see 'Technical Specification' below)
• For use with up to 150-Watts of dimmable LEDs or up to 600-Watts of Incandescent or Halogen bulbs
• Features a large rocker paddle to turn lights on/off or to preset level and a discreet slider to brighten/dim lights to suit any activity
• Can be used in single-pole or 3-way applications
• Installs in as little as 15 minutes. Operating temperatures 32 °F to 104 °F (0 °C to 40 °C)
• Includes Diva LED+ (formerly C.L) Dimmer Switch and coordinating wallplate

Product features

Lutron LED+ Dimmers provide over 250 lighting levels, so you can set the right light for any activity

• Large paddle switch to turn lights ON/OFF
• Sleek slider on the side to manually dim or brighten lights
• Technology that allows for smooth dimming of the broadest range of LEDs
• Patented technology to optimize the dim range of your bulb and prevent interference with other dimmers in the home
• Tried and true aesthetic to match designer/decorator style switches and accessories

Cutting Edge Technology

Our easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Blend In or Stand Out

Available in 25 colors so you can choose a finishing touch to your room that seamlessly blends in or a color that is meant to pop

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

Product description

Bring technology and style to your home with the Lutron Maestro C×L Dimmer, the first digital dimmer that is compatible with all of today's bulbs types dimmable CFL and LED, halogen, and incandescent. This digital dimmer gradually turns lights on and off, allowing your eyes to adjust to the new light level. LED's display the light level and glow softly in the dark, acting as a locator light so you can easily find the control in the dark. Use the rocker to adjust the light level for any activity or set the preset level to ensure lights always turn on to your desired light level. Advanced features include delayed fade to off, which allows time to exit a room or to get into bed before the lights turn off. Installing the Maestro C·L is simple and quick, and is perfect for any room in the home. It also coordinates with the entire Maestro family of controls including dimmers, switches, occupancy sensors, and more. Coordinating Claro wall plate is not included.

• Tested on 1,000s of bulbs and dozens of brands for flicker-free dimming. For list of recommended bulbs view "Technical Specification" below
• Provides over 250 lighting levels so you can create the perfect light for any activity
• Works with up to 150 Watts of dimmable LED/CFL bulbsor 600 Watts of Incandescent/Halogen bulbs For list of recommended bulbs, view "Technical Specification" below
• Lutron patented technology to optimize the dim range of your bulbs and prevent interference with other dimmers in the home
• Can be used in single-pole or 3-Way/multi-location dimming applications (up to 10 locations, Maestro companion dimmer MA-RR-XX required)

User questions & answers

Question:	Is anyone using this with an LED and if so, for how long and how is it working? Thanks
Answer:	I'm using this with two 12.5W Soraa High-CRI "Vivid" series LED PAR30 4000K bulbs (total controlled load: 25W) and it is the finest dimmer switch I've ever used. With the "Advanced mode" custom programming (Technical document: www.lutron.com/TechnicalDocumentLibrary/048459.pdf) to adjust the "low trim" (dimmest point) I can get these bulbs to be on and stable at only
Question:	Can this handle dimming LED lights all the way down so they are actually dim, like the incandescents? Yes, I have an LED light bulb that is dimmable
Answer:	I have the Wafer 6 in. White Integrated LED Recessed Kit that Home Depot sells. They say they can go down to 10%.. I had another switch in previously that the lights wouldn't dim down as far and would turn off randomly when dimmed down all the way. If you use the adjustment feature in this switch it seems like they go down to that no problem. I've been running them for a day and no flickering or turning off. If anything changes I'll leave an updated comment or update this answer. Two factors you'll need to look at: 1) what is the LED bulb rated to go down to 2) Is this dimmer compatible? If your LED bulb says it can do it try many different dimmers until one works :)
Question:	The max brightness seems lower than when I had a non-digital dimmer. How do I adjust? I see instructions for the lower dim range but not the max
Answer:	Please see Lutron's Application Note #459. All of these settings are NOT listed in the manual that came with your switch. www.lutron.com/TechnicalDocumentLibrary/048459.pdf You want to adjust IL7, the high-end trim.IL1: Preset Light Level (last setting or set permanently)IL2: Fade ON Time (0.75 to 15.0 seconds)IL3: Fade OFF Time (0.75 to 15.0 seconds)IL4: Delayed Fade to OFF (time to leave the room - 10 to 70 seconds)IL5: Enable/Disable Indicator Lights (LED dots off or on)IL6: Low-End Trim (minimum brightness)IL7: High-End Trim (maximum brightness)
Question:	how much power do led indicator lights draw
Answer:	Approximately 0.02 Watts (2 cents per year at $0.10/kWh) if they did the job right of designing it (switching converter,) and 0.25 Watts (20 cents per year at $0.10/kWh) if they took the lazy way out (simple resistor.)

Product features

Cutting Edge Technology

Our patented easy-to-set adjuster via button press programming allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control Up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs and is the only dimmer UL listed to control mixed loads (different types of bulbs on the same circuit).

Blend in or Stand Out

Available in 25 colors so you can choose a finishing touch to your room that seamlessly blends in or a color that is meant to pop.

Works Well with LEDs

Tested on 1,000s of bulbs and dozens of brands to ensure flawless dimming. Check out the Lutron website for our list of recommended bulbs.

Product description

Lutron LED+ dimmers provide the best dimming performance for LED bulbs while setting the right light level to improve mood and ambiance for any activity. Designed specifically for dimmable lads and CFL, as well as for use with traditional incandescent and halogen bulbs, they greatly improve the dimming performance when compared to standard dimmers. Featuring advanced circuitry designed to alleviate common challenges, like flicker and pop on, LED+ dimmers are compatible with 800+ bulbs - for more specific details on compatible bulbs, view "technical specification" below. The Diva dimmer matches existing decor a style switches and fits in a standard decor a style wall plate (CW-1-WH). it features a large paddle switch that turns the lights on/off and returns them to your favorite preset setting, along with a discreet slider that brightens or dims the lights to suit any activity.

• Provides the best dimming performance for dimmable LED bulbs (compatible with 800+ bulbs - for more specific details view technical specification" below)
• For use with up to 150-Watts of dimmable LEDs and up to 600-Watts of Incandescent and Halogen bulbs
• Features a large rocker paddle to turn lights on/off or to preset level and a discreet slider to brighten/dim lights to suit any activity
• Can be used in single-pole or 3-way applications
• Installs in as little as 15 minutes
• Includes Diva LED+ (formerly C.L) Dimmers; coordinating wallplates sold separately

User questions & answers

Question:	Can this item post to China directly from your warehouse
Answer:	sorry . can not sell to china.
Question:	Do these come in a version without the logo on the front
Answer:	no
Question:	Is there a compatible led edison e26 bulb
Answer:	Currently, there is no industry standard or regulation for the manufacturing of LEDs and the performance will vary with different dimming controls. With this information in mind, Lutron performs extensive testing on a variety of LEDs from many different manufacturers and posts our most up to date testing information on our LED compatibility tool. Lutron would suggest visiting www.lutron.com/ledfinder to determine compatibility with your LEDs. Please feel free to reach out to our Support Team at [email protected] or by phone at 1 (844) 588-7661 with any questions/concerns.
Question:	I installed these dimmers with LEDP3120WH - 120V Direct LED Puck Light Kit. When I turn the power back on the lights pulse/flicker constantly. Ideas
Answer:	I am posting what my husband said as he installed he dimmer. It depends on the "kit" and the light bulbs used. I noticed some LED bulbs (or those "curly" bulbs) do not work with dimmers.

Product features

Cutting Edge Technology

Out patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Blend In or Stand Out

Available in 25 colors so you can choose a finishing touch to your room that seamlessly blends in or a color that is meant to pop

Works Well with LEDs

Tested on 1,000's of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

• Support single pole or 3-way applications, decor wall plate included. Only one dimmer switch can be installed per 3 way circuit
• LED Dimmer Light Switch: Provides the best dimming performance for LED bulbs. Simple and elegant horizontal slider dims and brightens with ease for full range light control
• Adjuster Dial: Ensures compatibility with almost all dimmable LED, CFL, incandescent and halogen bulbs, up to 150 watts of dimmable LED/CFL lamps or 600 watts of incandescent bulbs
• Smart Rocker: On/Off rocker switch remembers the last dimmed light setting and turns on to that exact light level
• 3 year limited warranty. UL listed

User questions & answers

Question:	does this switch have circuitry does it operate without creating buzzing or humming sound
Answer:	Dear Customer, Thanks for your question about BESTTEN Dimmer Switch. The device will not create buzzing or humming sound. If there are any issues, please feel free to contact us via [email protected] Sincerely BESTTEN Customer
Question:	Do these match your Snow White wall plates
Answer:	Dear Customer, Thanks for your enquriy on BESTTEN dimmer switches. The products match our yellow-white wall plate best. You can refer to the below link: https://www.amazon.com/dp/B07BLXZMBX?ref=myi_title_dp You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	Does this switch stop led blinking
Answer:	Dear Customer, Thanks for your enquriy on BESTTEN Dimmer Light Switch. If your light flicker when it works with this dimner, you can follow the motheds on description or mannual to adjust the adjust wheel to avoid it. You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	I understand that there can only be 1 dim switch in a 3-way setup. Can one of these switches be wired so it is only on/off
Answer:	Your cheaper off putting a standard 3 way for the second switch.

Product features

BESTTEN Modern Dimmer Switch

BESTTEN dimmer switch provides smooth, sliding and full-range dimming performance for dimmable LED, CFL, halogen and incandescent bulbs. The slider can dim and brighten your lights precisely and conveniently, creating a romantic mood or a casual atmosphere for family activities.

• Single pole or 3-way
• No neutral required
• Large ON/OFF rocker paddle switch
• Precise full-range dimming control
• Wide range of compatibility with sensitivity dial
• Wallplate included

Specifications

Voltage.....................................................................................................120V, 60Hz

Dimmable LED/CFL................................................................................Max. 150W

Incandescent/Halogen.............................................................................Max. 600W

Switch Type.............................................................................................Single Pole/3-Way

Wiring Type..............................................................................................Wire Pigtails

Operation Temperature...........................................................................32°F (0°C) --- 104°F (40°C)

Remind:

One circuit can ONLY install one dimmer switch.

Troubleshooting

Symptom:

- Bulbs turn off while being dimmed.

- Bulbs turn on at high light level but do not turn on at a low light level, or take too long to turn on at low end.

- Bulbs flicker or flash when dimmed do a low light level.

- Bulbs or dimmers are buzzing.

Solution:

1. Verify all bulbs are marked dimmable.

2. Remove wallplate and locate sensitivity dial.

3. Turn up (counter-clockwise) sensitivity dial slowly until symptom is no longer present.

• 3-Way Single Pole Compatible Slide control dimmer.Green indicator turns off when the load is on, turns on when the load if off.
• 600W max Incandescent; 150W max dimmable LED/CFL,120VAC, 60Hz*Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz *Not compatible with smart lighting fixtures
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included, easy to install.
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	With the switch on the dimmer works just fine. with the toggle switch off my led bulbs still glow slightly
Answer:	If you want to turn the light OFF, you must use the switch. The toggle will still give the lights some voltage even in the so called off position.
Question:	With the switch on the dimmer works just fine. with the toggle switch off my led bulbs still glow slightly
Answer:	Good

Product features

Dimmer Switch with Green Indicator

• Voltage: 120V AC
• Single Pole/3 Way installation.(please refer to brief wiring instruction below).
• Fine tune adjustment dial to eliminte LED/CFL flickering.
• No screws needed to fasten wall plate. Looks perfectly blend into the wall.
• Can be used with literally all kinds of your household lighting.
• Dimmer has been tested to be fully compatible with any light fixtures of Cloudy Bay Lighting family, including Cloudy Bay flush mount ceiling lights.
• NOT COMPATIBLE WITH SMART LIGHTS, SUCH AS GE C, PHILIPS HUE WHICH IS CONTROL BY WIFI, BLUE TEETH, ZIGBEE etc.

Compatible with CFL/LED/Incandescent

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Tip: Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

Fine tune with adjustment dial

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a. Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights.

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Product description

Control the next generation of lighting with Lutron's dimmable LED+ dimmers! Screw-in dimmable compact fluorescent lamps (CFLs) and screw-in dimmable light emitting diode lamps (LEDs) are a great energy-saving alternative to incandescent or halogen light sources; however, dimming them may be difficult. Lutron's new line of LED+ dimmers provides a solution to alleviate your dimmable CFL and LED dimming challenges, while allowing you to adjust the light level to improve mood and ambiance. with the same features as the original slide dimmer by Lutron, this Skylark dimmable CFL/LED dimmer features an easy to use slide control that adjusts the light to suit any activity, and a convenient switch that returns light to your favorite level. These dimmers still provide full-range dimming for halogen and incandescent bulbs, ensuring today's dimmer is compatible with tomorrow's light sources. The dimmer can even dim a mixed load of light sources (i.e. LED and halogen or CFL and LED bulbson the same circuit). Claro wallplate is not included.

• Tested on 1,000s of bulbs and dozens of brands for flicker-free dimming. For list of recommended bulbs view Technical Specification
• Provides over 250 lighting levels so you can create the perfect light for any activity
• Works with up to 150 Watts of dimmable LED/CFL bulbsor 600 Watts of Incandescent/Halogen bulbs
• Lutron patented technology to optimize the dim range of your bulbs and prevent interference with other dimmers in the home
• Can be used in single-pole or 3-Way applications, where lights are controlled from one or two locations
• Rocker switch turns lights on/off to favorite light level. Discreet slider dims and brightens the lights
• Includes Skylark LED+ (formerly C.L) Dimmer Switch; coordinating wallplate sold separately

User questions & answers

Question:	How do I wire this with no ground
Answer:	Note 4 of the installation instructions states: When no "grounding means" exist in wallbox, the 2011 NEC allows a control to be installed as a replacement if 1) a nonmetallic ,noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a GFCI. When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.
Question:	So I have two can light led’s wired to a 2 toggle switch plate, can I remove the light receptacle and replace with this to dim the lights
Answer:	As long as the LEDs you are using are compatible with this dimmer, then yes it will work properly for your application. For more information on compatible LED lamps, Lutron would reccomed checking out their LED tool at Lutron.com/ledfinder.
Question:	Can i use 2 of these to dim from either location on a 3way (currently an old skylark and an on/off switch)? or do i need a maestro setup
Answer:	On 3-way circuits, only one ELECTRO-MECHANICAL switch can be a dimmer regardless of lamp type, other switch must be standard single-pole 3-way on/off. You CAN use DIGITAL ELECTRONIC CONTROL SYSTEM (ie: MAESTRO) for all switches on circuit. Skylark SCL-153P dimmer is "electronic" but it is not a CONTROL SYSTEM that encompasses the whole circuit.
Question:	Can this dim incandescent and LED bulbs on the same circuit
Answer:	Yes- the issue is that the bulbs are very different and as a result will not dim uniformly so when dimmed one may be brighter

Product features

Cutting Edge Technology

Our patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Fast and Easy Installation

All you need to replace your existing switch or dimmer is about 15 minutes, 3 simple steps and 1 screwdriver

Works Well with LEDs

Tested on 1,000s of bulbs and dozens of brands to ensure flawless dimming. Check out the Lutron website for our list of recommended bulbs.

Product description

Lutron LED+ dimmers provide the best dimming performance for LED bulbs while setting the right light level to improve mood and ambiance for any activity. Designed specifically for dimmable leds and CFL, as well as for use with traditional incandescent and halogen bulbs, they greatly improve the dimming performance when compared to standard dimmers. Featuring advanced circuitry designed to alleviate common challenges, like flicker and pop on, LED+ dimmers are compatible with 800+ bulbs - for more specific details on compatible bulbs, view "technical specification" below. The Toggler dimmer matches existing toggle switches and fits in a standard wall plate (fg-1-wh). it features a toggle switch that turns the lights on/off and returns them to your favorite preset setting, along with a discreet slider that brightens or dims the lights to suit any activity. This Toggler multi-pack included Toggler LED+ dimmers, wall plates sold separately.

• Tested on 1, 000s of bulbs and dozens of brands for flicker-free dimming. For list of recommended bulbs view "Technical Specification"
• Provides over 250 lighting levels so you can create the perfect light for any activity
• Works with up to 150 Watts of dimmable LED/CFL bulbs or 600 Watts of Incandescent/Halogen bulbs
• Lutron patented technology to optimize the dim range of your bulb and prevent interference with other dimmers in the home
• Can be used in single-pole or 3-Way applications, where lights are controlled from one or two locations
• Includes Lutron Toggler LED+ (formerly C.L) Dimmer Switches; coordinating wallplates sold separately

User questions & answers

Question:	Can this dimmer be used for xenon lights? If not, what type do I need
Answer:	Hello, Yes these are brand new and in original packaging
Question:	i have two black wires, 2 red wires and a ground going into the one I am replacing, this only has 3 hookups, any way around this
Answer:	The unit that we have Current version on the switch that we are selling. Version (YA.15.12.2007) Reset to factory default setting These switches can be upgrade and or down graded by logging into Aruba's web site. There may be a charge, but I am not sure about that.
Question:	Anyone know the difference between the "Ariadni" switch (AYCL-153P) and the "Toggler" switch (TGCL-153P
Answer:	Yes, have problem on the keyboard, yes.
Question:	Can this be used (minus plate) to replace 1 switch in a 3 or 4 switch box? Will the actual switch plus dimmer lever be too wide for the plate hole
Answer:	It's a volume control wheel.

Product features

Cutting Edge Technology

Our patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Fast and Easy Installation

All you need to replace your existing switch or dimmer is about 15 minutes, 3 simple steps and 1 screwdriver

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

• Support single pole or 3-way applications, decor wall plate included. Only one dimmer switch can be installed per 3 way circuit
• LED Dimmer Light Switch: Provides the best dimming performance for LED bulbs. Simple and elegant horizontal slider dims and brightens with ease for full range light control
• Adjuster Dial: Ensures compatibility with almost all dimmable LED, CFL, incandescent and halogen bulbs, up to 150 watts of dimmable LED/CFL lamps or 600 watts of incandescent bulbs
• Smart Rocker: On/Off rocker switch remembers the last dimmed light setting and turns on to that exact light level
• 3 year warranty. UL listed. NOTE: The dimming range of dimmable LEDs may vary from manufacturer to manufacturer. This dimmer has an adjustable dimming range. Please rotate the side adjustment wheel to eliminate flicker issues

User questions & answers

Question:	are these ul listed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. Yes, they are UL listed. You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	I am replacing incandescent dimmer switches these led switches are 2.12 inches wide. my existing switches are 1.75 inches wide. can they be trimmed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. The side tabs can be removed which will reduce the width to 1.75in. Any other question, please contact us via [email protected] or call 800-358-6160. BESTTEN Customer Care
Question:	Do they come in light almond
Answer:	Don't think so.
Question:	Can we use these dimmers with leds that requires 0-10v dimming control (driver) 120-277v
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN dimmer light switch. Yes, it can install in a 120v circuit and control a 0-10v dimmable LED lights. BESTTEN Customer Care [email protected]

Product features

BESTTEN Modern Dimmer Switch

BESTTEN dimmer switch provides smooth, sliding and full-range dimming performance for dimmable LED, CFL, halogen and incandescent bulbs. The slider can dim and brighten your lights precisely and conveniently, creating a romantic mood or a casual atmosphere for family activities.

• Single pole or 3-way
• No neutral required
• Large ON/OFF rocker paddle switch
• Precise full-range dimming control
• Wide range of compatibility with sensitivity dial
• Wallplate included

Specifications

Voltage.....................................................................................................120V, 60Hz

Dimmable LED/CFL................................................................................Max. 150W

Incandescent/Halogen.............................................................................Max. 600W

Switch Type.............................................................................................Single Pole/3-Way

Wiring Type..............................................................................................Wire Pigtails

Operation Temperature...........................................................................32°F (0°C) --- 104°F (40°C)

Remind:

One circuit can ONLY install one dimmer switch.

Troubleshooting

Symptom:

- Bulbs turn off while being dimmed.

- Bulbs turn on at high light level but do not turn on at a low light level, or take too long to turn on at low end.

- Bulbs flicker or flash when dimmed do a low light level.

- Bulbs or dimmers are buzzing.

Solution:

1. Verify all bulbs are marked dimmable.

2. Remove wallplate and locate sensitivity dial.

3. Turn up (counter-clockwise) sensitivity dial slowly until symptom is no longer present.

Product description

Decora Slide Dimmer. 600W-120VAC incandescent, and 300W-120VAC dimmable LED and CFL, 60Hz. Single pole or 3-way control when used with 3-way switch. Comes with white faceplate installed, optional ivory and light almond faceplates included. Wallplate sold separately. Can be used to comply with 2016 California Title 24, Part 6, Indoor Lighting Switching Devices and Controls. No fins for multi-gang installation.

• INNOVATIVE - Designed to dim LED bulbs; For the best bulb pairings, refer to the "comparison chart" in the technical specification section below
• FLEXIBLE; Can be used in a single pole or 3 way installation (with a 3 way switch, sold separately); No neutral wire required for installation
• CONVENIENT; Separate ON/OFF rocker switch allows you to set and keep preferred dimming level; Built-in radio/TV interference filter
• ADVANCED; Adjustment switch to modify the minimum light level in order to maximize the dimming range if flickering occurs at lower dimming levels
• STYLISH; Complements with leviton decora plus screwless and Decora standard designer wallplates, sold separately

User questions & answers

Question:	How long is the warranty period
Answer:	it says 5 yr in description specifications , which is it please
Question:	I want to use this for a 3 way switch. Can the other 3 way switch be a standard Leviton switch (what's already there
Answer:	Yes it should work
Question:	Has anyone had an issue with your led's remaining slightly on when this switch is in the off position
Answer:	When the locator light is in the ON position, a very small amount of current is passed through the LED bulb. Very sensitive LED bulbs may appear to glow from this current. To fix, turn the locator light to the OFF position.
Question:	I have dimmable leds, but. They don't dim very low, and at high end they flicker, any help
Answer:	Unfortunately, not all "dimmable" LED lights are "made equal" NOR are all "dimmers" made equal. I continue to have a very similar problem with this dimmer and my dimmable LEDs as well. I have a little background in electronics and have concluded that in my case, there is simply a problem with the Leviton dimmer design. One thing I did while testing my problem, might help diagnose the problem your are having. Note that the spec on the dimmer is "300-Watt LED". Check that the total "load" on the dimmer is

Product features

Multiple Locations

Perfect in large areas or hallways/staircases that have two switches that control

the same light(s).

Leviton Dimmers Put You In Control

Set the mood by adjusting the light level for any activity. Whether you are

entertaining, reading, keeping the little ones safe from bedtime “monsters” or watching the latest flick, you're in control.

Superior Performance

Take advantage of the full dimming range of your bulb by adjusting the minimum

light level on the dimmer.

Compatibility is Key

To achieve the best dimming performance, ensure that the bulbs are compatible.

Download the “comparison chart” in the technical specification section below to see the best pairings for this dimmer.