14 best dimmer switch for leds

• 3-Way Single Pole Compatible Slide control dimmer.If UP is off(DOWN is on) after wiring, try switching around the two red wires to reverse the on/off direction
• Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	Where is it made? USA
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	I doubt it, but contact mfg., they are very responsive.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	Check the display is ON or OFF on the top left connor, it should show ON then the device can work.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	What I think was being asked is if this meter can tell you the PEAK load during the time it was connected. For example, let's say it was connected to a refrigerator for 10 hours. Let's say that during that 10 hours the load in Watts was 150Watts. But, when the compressor kicks in, it surges to 2000Watts for 3 seconds. Will this device allow you to see that 2000Watt PEAK later? Does it store that PEAK load into memory so you can view it?

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Product description

The Leviton toggle slide universal dimmer provides smooth, slide-action, full-range dimming for dimmable LEDs, dimmable CFLs, incandescent and halogen bulbs. For a traditional home, the classic style offers the ideal way to upgrade the functionality without compromising the character of the decor.

• Classic design with toggle switch and integrated linear full-range slide control for easy, precise operation
• Designed specifically for dimmable LED and CFL bulbs; Also compatible with incandescent and halogen bulbs
• Single pole or 3 way capable when used with a 3 way switch. No removal of fins required for multi-gang installations
• Built-in starting technology for CFL bulbs; Allows users to modify the dimming range to optimize low light level performance when required (optional)
• Wider dimming range for LED and CFL bulbs than traditional incandescent dimmers

User questions & answers

Question:	Will this dimmer stand 12 AR111 12Watts each
Answer:	Dimmer will control 300 watt dimmable LEDs if the AR111s you have are dimmable 120V 12Watt lights then switch should be OK as 12 lights would be ~144 Watts
Question:	We were trying to connect this switch, the light is on but the dimmer is not working, its a single pole, what am I missing
Answer:	You need to be using "dimmable" bulbs, either incandescent or LED, but not fluorescent. If you are using dimmable incandescent or LED bulbs, I believe there is a slider control (switch) somewhere on this switch to choose either incandescent or LED. That needs to match your bulb type.
Question:	I installed the switch as well as dimmable led bulbs. they work on the dim setting but they blink from half all the way to full power, any ideas
Answer:	I've had similar issues and took it up with Leviton on their website. They initially just asked me to send it back to them, but I stopped short stating that I didn't particularly want to "finance" that. So they did send me a replacement unit and a prepaid shipping label. The replacement one is "better", but sometimes it still goes into flicker or as I call it "spazz" mode. They have asked me for the exact bulbs I'm using (Ecosmart Classic Glass Bulbs from Home Depot) but nothing further from them. I use those same bulbs in (2) other fixtures with Lutron LED dimmers (Model# TGCL-153PH-WH and Model# CTCL-153PR-WH) and they both have worked flawlessly for about a year. Never a single flicker. Bob
Question:	Where is the locator light
Answer:	Mine has a green LED at the top of the toggle switch. It is almost impossible to see in the light, but when the room is dark, it is visible without being disturbing. It comes defaulted to OFF. There are two micro switches on the front of the switch, which are hidden once that switch plate is put on. The top switch has an A and B position. A (the default) is for LED and incandescent lights. B is for CFC bulbs. A second switch, lower down, is for the locator light. Set the switch to ON if you want to use the light. Set these switches before you put on the switch plate because the plate covers these switches.

Product features

Leviton TSL06-1LW Toggle Slide Universal Dimmer

Leviton’s TSL06 Toggle Slide universal dimmer is engineered to provide homeowners optimal control of 300-watt Dimmable LED and CFL bulbs, and 600-watt Incandescent and Halogen bulbs. This new dimmer offers the energy-saving benefits of dimming without sacrificing performance or the time-honored design valued in traditional homes. The Toggle Slide universal dimmer addresses performance issues–such as flickering, reduced dimming range, and low level start up–often experienced when incandescent-only dimmers are paired with dimmable LED or CFL bulbs.

Great Dimming, Traditional Style

The Toggle Slide universal dimmer features an on/off preset function which preserves the selected dimmer setting, smooth start-up, gentle-touch control, and fluid slide movement for precise dimming. The device’s traditional aesthetics offer the ideal way to upgrade functionality from standard switches without compromising the character of your traditional decor. Its slim, compact housing fits easily into a standard wall box and is suitable for multi-gang installations. The Toggle Slide universal dimmer is compatible with Leviton’s complete line of signature Decora wiring devices and wall plates.

Advanced Features

The Leviton Toggle Slide universal dimmer features a microprocessor control which offers the flexibility to fine-tune LED and CFL bulbs for best performance. A “kick-start” setting is available to ensure start-up of CFL bulbs. The dimmer also features a soft green LED locator light built into the switch, making it easy to find in a dark room.

About Leviton Dimmers

Leviton is a leading manufacturer of dimmers designed for both the energy-saving benefits of dimming and the ambiance that can be created in any room of the home by controlling lighting levels. To ensure superior performance, Leviton works with bulb manufacturers to develop dimmers that are tested and proven effective to function in harmony with the latest bulb innovations. Leviton dimmers come in a wide range of models including digital, wireless, preset, slide, rotary, toggle, and touch and provide precise dependable control.

• 3-Way Single Pole Compatible Slide control dimmer.Green indicator turns off when the load is on, turns on when the load if off.
• 600W max Incandescent; 150W max dimmable LED/CFL,120VAC, 60Hz*Fully compatible with Cloudy Bay LED light fixtures,600W max Incandescent,150W max Dimmable LED/CFL,120VAC,60Hz *Not compatible with smart lighting fixtures
• Works with LED,Halogen,Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Decorative Wall Plate and Mounting Screws Included, easy to install.
• UL Listed,1 Year Warranty. Please contact us if there is any issue with dimming issue.

User questions & answers

Question:	With the switch on the dimmer works just fine. with the toggle switch off my led bulbs still glow slightly
Answer:	If you want to turn the light OFF, you must use the switch. The toggle will still give the lights some voltage even in the so called off position.
Question:	With the switch on the dimmer works just fine. with the toggle switch off my led bulbs still glow slightly
Answer:	Good

Product features

Dimmer Switch with Green Indicator

• Voltage: 120V AC
• Single Pole/3 Way installation.(please refer to brief wiring instruction below).
• Fine tune adjustment dial to eliminte LED/CFL flickering.
• No screws needed to fasten wall plate. Looks perfectly blend into the wall.
• Can be used with literally all kinds of your household lighting.
• Dimmer has been tested to be fully compatible with any light fixtures of Cloudy Bay Lighting family, including Cloudy Bay flush mount ceiling lights.
• NOT COMPATIBLE WITH SMART LIGHTS, SUCH AS GE C, PHILIPS HUE WHICH IS CONTROL BY WIFI, BLUE TEETH, ZIGBEE etc.

Compatible with CFL/LED/Incandescent

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Tip: Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

Fine tune with adjustment dial

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a. Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights.

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Product description

Lutron LED+ dimmers provide the best dimming performance for LED bulbswhile setting the right light level to improve mood and ambiance for any activity. Designed specifically for dimmable lads and CFL, as well as for use with traditional incandescent and halogen bulbs, they greatly improve the dimming performance when compared to standard dimmers. Featuring advanced circuitry designed to alleviate common challenges, like flicker and pop on, LED+ dimmers are compatible with 800+ bulbs- for more specific details on compatible bulbs, view "technical specification" below. The Diva dimmer matches existing decor a style switches and fits in a standard decor a style wall plate (CW-1-WH). It features a large paddle switch that turns the lights on/off and returns them to your favorite preset setting, along with a discreet slider that brightens or dims the lights to suit any activity.

Create the perfect amount of light while utilizing the latest energy-saving technology with the Lutron Diva C•L Dimmer. Designed for use with 150-watt dimmable CFL or LED lights, the Lutron Diva C•L dimmer features a large paddle switch that automatically returns to your favorite pre-selected light level, a discreet slider to adjust light levels, and a sleek, modern wallplate.

Diva C•L Dimmer At a Glance: Dimmer works with most dimmable CFL/LED bulbs, as well as incandescent and halogen bulbs Slider for precise light control and paddle switch for easy on/off HED technology improves the performance of dimmable CFLs and LEDs over standard dimmers Adjustment dial to set bottom of dimming range for your bulb type Single-pole and three-way applications One-year limited warranty; UL-listed for a broad range of dimmable CFL/LED bulbs

Adjustment dial fine tunes dimming range for your specific bulb.

The C•L Dimmer works with a combination of CFL, LED, halogen, and incandescent bulbs and can be used on the same circuit.

Precise Light Adjustment with Slider

Whether you're reading, watching TV, entertaining, or enjoying a romantic dinner, the Lutron Diva C•L Dimmer lets you choose the right level of light for your activity. It's easy to make subtle adjustments using the discreet slider next to the large paddle switch. When you use the paddle switch to turn lights off and on, it defaults to your preferred lighting level.

Works with Dimmable CFLs and LEDs for Increased Energy Savings

The Lutron dimmer works with dimmable CFLs and LEDs up to 150 watts, a great energy-efficient alternative that can last up to 10 times longer than incandescent bulbs. Plus, by using less electricity, theses bulbs help protect the environment by reducing the amount of carbon dioxide released into the air.

HED Technology for Enhanced Performance

Thanks to Lutron's HED technology, this dimmer actually improves the performance of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, ensuring lights stay on when they are dimmed to a low level, and making sure lights operate properly at all levels. Lights will stay on even during voltage fluctuations, which can happen when a device like an air conditioner or a hair dryer is operated nearby. For safety, the dimmer is UL listed for a broad range of dimmable CFL and LED bulbs.

Compatible with Other Lightbulbs and Mixed Loads

For added functionality, the dimmer also provides full-range dimming for halogen and incandescent bulbs. There is an adjustment dial to set the low end of dimming range for your bulb type for most efficient operation.

The dimmer also works with a mixed load of light sources, so a combination of CFL, LED, halogen, and incandescent bulbs can be used on the same circuit. It can be used for single-pole and three-way applications.

Fast and Easy Installation

Installation is easy--just replace your existing light switch with the Lutron Diva C•L Dimmer and install in less that 15 minutes. A modern wallplate--with no visible screws--blends into the surrounding wall for a subtle finishing touch.

The Lutron Diva C•L Dimmer is backed by a one-year limited warranty.

What's in the Box

Dimmer and screwless wallplate.

Set the perfect mood lighting for any room with the Diva C•L Dimmer.

From the Manufacturer

Control the next generation of lighting with Lutron's dimmable C.L dimmers! Screw-in dimmable compact fluorescent lamps (CFLs) and screw-in dimmable light emitting diode lamps (LEDs) are a great energy-saving alternative to incandescent or halogen light sources; however, dimming them may be difficult. Lutron's new dimmers with HED Technology provides a solution to alleviate your dimmable CFL and LED dimming challenges, while setting the right light level to improve mood and ambiance. The Diva dimmable CFL/LED dimmer with HED Technology features advanced dimming circuitry that is designed for compatibility with most high efficacy light bulbs. With the same features as Lutron's Diva dimmer, the large paddle switch turns the light on/off and returns to your favorite setting. The discreet slider adjusts the light level to suit any activity. These dimmers improve the dimming performance of dimmable CFLs and LEDs compared to standard dimmers. Lutron dimmers with HED Technology also provide full-range dimming for halogen and incandescent bulbs, ensuring today's dimmer is compatible with tomorrow's light sources. The dimmer can even dim a mixed load of light sources (i.e. LED and halogen or CFL and LED bulbs on the same circuit).

• Provides the best dimming performance for LED bulbs(for list of approved LEDs, see 'Technical Specification' below)
• For use with up to 150-Watts of dimmable LEDs or up to 600-Watts of Incandescent or Halogen bulbs
• Features a large rocker paddle to turn lights on/off or to preset level and a discreet slider to brighten/dim lights to suit any activity
• Can be used in single-pole or 3-way applications
• Installs in as little as 15 minutes. Operating temperatures 32 °F to 104 °F (0 °C to 40 °C)
• Includes Diva LED+ (formerly C.L) Dimmer Switch and coordinating wallplate

Product features

Lutron LED+ Dimmers provide over 250 lighting levels, so you can set the right light for any activity

• Large paddle switch to turn lights ON/OFF
• Sleek slider on the side to manually dim or brighten lights
• Technology that allows for smooth dimming of the broadest range of LEDs
• Patented technology to optimize the dim range of your bulb and prevent interference with other dimmers in the home
• Tried and true aesthetic to match designer/decorator style switches and accessories

Cutting Edge Technology

Our easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Blend In or Stand Out

Available in 25 colors so you can choose a finishing touch to your room that seamlessly blends in or a color that is meant to pop

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

Product description

Lutron Ariadni dimmers are a simple and inexpensive way to add ambiance to any room in your home, while saving energy and extending bulbs life. This dimmer is designed to replace or match your traditional toggle style switches. The discreet slider next to the toggle switch adjusts the brightness of the bulbs to a desired level, while the toggle switch turns the light off and on to your favorite preset level. Designed with a shallow 1 inch deep back cover for easy installation, Ariadni and Toggler dimmers work with your existing traditional opening wall plates. Coordinating Facade screw less wall plates and accessories sold separately.

• Provides the best dimming performance for LED bulbs(compatible with 800+ bulbs- for more specific details view "technical specification" below)
• Also works with ALL incandescent and halogen bulbs
• Works with up to 150 Watts of dimmable LED/CFL bulbs or 600 Watts of Incandescent/Halogen bulbs
• Can be used in Single-Pole or 3-Way applications
• Toggle switch turns lights on/off and returns light to preset level, slider dims and brightens
• Includes Lutron Toggler LED+ (formerly C.L) Dimmer Switch; coordinating wallplate sold separately

User questions & answers

Question:	Is this considered triac based (forward phase control or leading edge) or 0-10v switch
Answer:	The AYCL-153P is a triac based dimmer rated for 150W of compatible LED/CFL or 600W of incandescent/halogen lighting. For compatible LEDs with this dimmer, or another Lutron dimmer, please visit www.lutron.com/ledfinder or www.lutron.com/ledtool.
Question:	do I need two of these switches in a 3-way application or can I use one dimmer with a normal 3-way on the other end
Answer:	Lutron does not recommend two AYCL-153P-WH dimmers in 3-way application. The second location would need to be a standard 3-way mechanical switch.
Question:	Can you fit three of these switches side by side in a standard 3 gang box
Answer:	The switch generates heat so it has tabs on both sides to prevent you from mounting them side by side without being aware that you have to "derate" them if you want to install them side be side. In other words, you can put 600 watts of incandescent bulbs on one dimmer if you mount it alone but only 500 watts of incandescent on a dimmer with one side tab removed (you remove only the tab(s) that overlap) and only 400 watts load with both tabs removed (as you would do mounting 3 switches in a standard 3 gang box). They also include a chart for derating when you mix CFL/LED bulbs with incandescent.
Question:	Anyone know the difference between the "Ariadni" switch (AYCL-153P) and the "Toggler" switch (TGCL-153P
Answer:	I was wondering this exact same question, so I called Lutron and learned that they're the exact same switch. The model numbers differ because they're marketed/sold differently (e.g. Home Depot vs. other stores). So, if you find one cheaper than another, as I've done here on Amazon, buy the less expensive one!
Question:	Where is it made? USA
Answer:	HI，Customer， It is Made in China, UL listed
Question:	Are there a 2, 3 snd 4 gang wall plates for these
Answer:	Yes, these are standard size switches. Home Depot or Lowes should have multi-gang plates.
Question:	installed but not turning on when the slide is in between and also hear some sound when you keep your ears on switch in dim mode . anyone else faced
Answer:	No sounds from mine. Make sure your bulbs a dimmable type? Just a guess.
Question:	can this dimmer be used on 12 volt LED lamps
Answer:	I doubt it, but contact mfg., they are very responsive.

Product features

SINGLE POLE/3-WAY CIRCUIT INSTALLATION

• Single Pole: Connect the green dimmer ground wire to ground wire in the wall-box, Connect the black dimmer wire to the hot input wire removed from the switch,Connect either of the 2 red dimmer wires to the light fixture wire removed from the switch,Use wire nut to cap the remaining red wire on dimmer
• 3-Way: Connect the green dimmer ground wire to the ground wire in the wall-box, Connect the black dimmer wire to the TAG wire removed from the switch, Connect the red dimmer wires to the remaining wires removed from the switch

Manual Control

At the low end of the dimming level when the light starts to flicker, fine tune the dimming performance by turning the adjustment dial counter-clockwise so that the light output is stable. Set your slider to where there's no hum or flickering on light fixtures.

Screw-free wall plate

Install the dimmer and mounting frame with the tabs facing down. Put on the screw-free wall plate after tuning the adjustment dial.

Compatible with CFL/LED

Cloudy Bay dimmer improves the compatibility of dimmable CFLs and LEDs compared to standard dimmers by eliminating flicker, making sure lights operate properly at all levels.

Trouble shooting

1: Light flash in the whole dimming range

a. Check the lighting/lamp is dimmable or not

b. The lighting fixture is not compatible with our dimmer

c. Most dimmable LEDs and CFLs will not acheive as low level as incandescent or halogen sources.

d. Control a group of lighting fixtures/lamps with one dimmer may cause flicker due to variation of dimming circuit and dimming range. Please use dimmer to

control lights/lamps in the same type or same model.

2. Light flash in low dimming range

a.Slightly turn the adjustment dial counter- clockwise to achieve full compatibility with the lights

3. Get dimmer list from light bulb/lighting fixture's supplier to avoid compatible issue with our dimmer, a broad dimmer list means less dimming issue, such as flicker,buzz, or flash issue, also, better buy FCC compliance lighting product for stable performance.

Cutting Edge Technology

Our patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Fast and Easy Installation

All you need to replace your existing switch or dimmer is about 15 minutes, 3 simple steps and 1 screwdriver

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

Product description

Bring technology and style to your home with the Lutron Maestro C×L Dimmer, the first digital dimmer that is compatible with all of today's bulbs types dimmable CFL and LED, halogen, and incandescent. This digital dimmer gradually turns lights on and off, allowing your eyes to adjust to the new light level. LED's display the light level and glow softly in the dark, acting as a locator light so you can easily find the control in the dark. Use the rocker to adjust the light level for any activity or set the preset level to ensure lights always turn on to your desired light level. Advanced features include delayed fade to off, which allows time to exit a room or to get into bed before the lights turn off. Installing the Maestro C·L is simple and quick, and is perfect for any room in the home. It also coordinates with the entire Maestro family of controls including dimmers, switches, occupancy sensors, and more. Coordinating Claro wall plate is not included.

• Tested on 1,000s of bulbs and dozens of brands for flicker-free dimming. For list of recommended bulbs view "Technical Specification" below
• Provides over 250 lighting levels so you can create the perfect light for any activity
• Works with up to 150 Watts of dimmable LED/CFL bulbsor 600 Watts of Incandescent/Halogen bulbs For list of recommended bulbs, view "Technical Specification" below
• Lutron patented technology to optimize the dim range of your bulbs and prevent interference with other dimmers in the home
• Can be used in single-pole or 3-Way/multi-location dimming applications (up to 10 locations, Maestro companion dimmer MA-RR-XX required)

User questions & answers

Question:	Is anyone using this with an LED and if so, for how long and how is it working? Thanks
Answer:	I'm using this with two 12.5W Soraa High-CRI "Vivid" series LED PAR30 4000K bulbs (total controlled load: 25W) and it is the finest dimmer switch I've ever used. With the "Advanced mode" custom programming (Technical document: www.lutron.com/TechnicalDocumentLibrary/048459.pdf) to adjust the "low trim" (dimmest point) I can get these bulbs to be on and stable at only
Question:	Can this handle dimming LED lights all the way down so they are actually dim, like the incandescents? Yes, I have an LED light bulb that is dimmable
Answer:	I have the Wafer 6 in. White Integrated LED Recessed Kit that Home Depot sells. They say they can go down to 10%.. I had another switch in previously that the lights wouldn't dim down as far and would turn off randomly when dimmed down all the way. If you use the adjustment feature in this switch it seems like they go down to that no problem. I've been running them for a day and no flickering or turning off. If anything changes I'll leave an updated comment or update this answer. Two factors you'll need to look at: 1) what is the LED bulb rated to go down to 2) Is this dimmer compatible? If your LED bulb says it can do it try many different dimmers until one works :)
Question:	The max brightness seems lower than when I had a non-digital dimmer. How do I adjust? I see instructions for the lower dim range but not the max
Answer:	Please see Lutron's Application Note #459. All of these settings are NOT listed in the manual that came with your switch. www.lutron.com/TechnicalDocumentLibrary/048459.pdf You want to adjust IL7, the high-end trim.IL1: Preset Light Level (last setting or set permanently)IL2: Fade ON Time (0.75 to 15.0 seconds)IL3: Fade OFF Time (0.75 to 15.0 seconds)IL4: Delayed Fade to OFF (time to leave the room - 10 to 70 seconds)IL5: Enable/Disable Indicator Lights (LED dots off or on)IL6: Low-End Trim (minimum brightness)IL7: High-End Trim (maximum brightness)
Question:	how much power do led indicator lights draw
Answer:	Approximately 0.02 Watts (2 cents per year at $0.10/kWh) if they did the job right of designing it (switching converter,) and 0.25 Watts (20 cents per year at $0.10/kWh) if they took the lazy way out (simple resistor.)

Product features

Cutting Edge Technology

Our patented easy-to-set adjuster via button press programming allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control Up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs and is the only dimmer UL listed to control mixed loads (different types of bulbs on the same circuit).

Blend in or Stand Out

Available in 25 colors so you can choose a finishing touch to your room that seamlessly blends in or a color that is meant to pop.

Works Well with LEDs

Tested on 1,000s of bulbs and dozens of brands to ensure flawless dimming. Check out the Lutron website for our list of recommended bulbs.

Product description

Save energy and money with the GE-branded Single Pole Toggle Dimmer Ideal for replacing a standard switch this toggle dimmer provides smooth dimming performance through a single pole installation Adjusting light levels with the dimmer's full range of light controls can significantly reduce your home's energy costs! The dimmer allows you to adjust the lighting in any room to fit any situation - turn the lights up when you have company or dim them for a movie The bright white finish complements existing decor no matter your style Compatible with single toggle traditional style wallplates this switch features a sturdy housing with removable tabs for multigang installations This dimmer works with incandescent dimmable LED and dimmable CFL bulbs Use indoors only with one-switch permanently installed lighting fixtures — wallplate not included This product is UL listed and backed by a one-year no-hassle replacement policy Update your current lighting with a GE-branded Single Pole Toggle Dimmer

From the Manufacturer

Adjusts light levels to reduce energy costs

• Control – Use the ON/OFF toggle switch to dim lights with single-switch applications for smooth full-range light control
• Multifunction – Use with dimmable LED and CFL bulbs as well as incandescent bulbs
• Colors – In order to best complement your home this GE Dimmer is available in bright white to match your existing fixtures
• Save – Reduce your energy costs with dimmable lights that minimize wasted electricity
• Power – Use up to 150W in dimmable LED and CFL bulbs or 600W with incandescent bulbs

User questions & answers

Question:	Is the diming controlled with a separate slide, or does the lever control both on/dim/off
Answer:	This model has a maximum incandescent rating of 600 watts. We do not have a higher wattage version of the touch sensing dimmer.
Question:	Is there a PDF for the instructions sheet
Answer:	Thanks for reaching out! We have a list of known compatible bulbs that have been tested with these switches you can find that information at https://www.gelighting.com/compatibility. We also sell our own dimmable LED bulbs that work with these switches, you will just have to set the bulb type in the switch settings. Please reach out to our support team if you need further assistance. -C by GE Support
Question:	Does the lever "click" into a full off position
Answer:	If your intent is to use these switches as a 3-way (2 switches controlling 1 set of lights) then yes, our switches can do that. However, both switches will need to be C by GE switches. Please contact our support staff for more information regarding the switches, thank you!

• Support single pole or 3-way applications, decor wall plate included. Only one dimmer switch can be installed per 3 way circuit
• LED Dimmer Light Switch: Provides the best dimming performance for LED bulbs. Simple and elegant horizontal slider dims and brightens with ease for full range light control
• Adjuster Dial: Ensures compatibility with almost all dimmable LED, CFL, incandescent and halogen bulbs, up to 150 watts of dimmable LED/CFL lamps or 600 watts of incandescent bulbs
• Smart Rocker: On/Off rocker switch remembers the last dimmed light setting and turns on to that exact light level
• 3 year warranty. UL listed. NOTE: The dimming range of dimmable LEDs may vary from manufacturer to manufacturer. This dimmer has an adjustable dimming range. Please rotate the side adjustment wheel to eliminate flicker issues

User questions & answers

Question:	are these ul listed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. Yes, they are UL listed. You can also reach us via [email protected] or 800-358-6160 BESTTEN Customer Care
Question:	I am replacing incandescent dimmer switches these led switches are 2.12 inches wide. my existing switches are 1.75 inches wide. can they be trimmed
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN Dimmer Switch. The side tabs can be removed which will reduce the width to 1.75in. Any other question, please contact us via [email protected] or call 800-358-6160. BESTTEN Customer Care
Question:	Do they come in light almond
Answer:	Don't think so.
Question:	Can we use these dimmers with leds that requires 0-10v dimming control (driver) 120-277v
Answer:	Dear Customer, Thanks for your enquiry on BESTTEN dimmer light switch. Yes, it can install in a 120v circuit and control a 0-10v dimmable LED lights. BESTTEN Customer Care [email protected]

Product features

BESTTEN Modern Dimmer Switch

BESTTEN dimmer switch provides smooth, sliding and full-range dimming performance for dimmable LED, CFL, halogen and incandescent bulbs. The slider can dim and brighten your lights precisely and conveniently, creating a romantic mood or a casual atmosphere for family activities.

• Single pole or 3-way
• No neutral required
• Large ON/OFF rocker paddle switch
• Precise full-range dimming control
• Wide range of compatibility with sensitivity dial
• Wallplate included

Specifications

Voltage.....................................................................................................120V, 60Hz

Dimmable LED/CFL................................................................................Max. 150W

Incandescent/Halogen.............................................................................Max. 600W

Switch Type.............................................................................................Single Pole/3-Way

Wiring Type..............................................................................................Wire Pigtails

Operation Temperature...........................................................................32°F (0°C) --- 104°F (40°C)

Remind:

One circuit can ONLY install one dimmer switch.

Troubleshooting

Symptom:

- Bulbs turn off while being dimmed.

- Bulbs turn on at high light level but do not turn on at a low light level, or take too long to turn on at low end.

- Bulbs flicker or flash when dimmed do a low light level.

- Bulbs or dimmers are buzzing.

Solution:

1. Verify all bulbs are marked dimmable.

2. Remove wallplate and locate sensitivity dial.

3. Turn up (counter-clockwise) sensitivity dial slowly until symptom is no longer present.

Product description

Lutron LED+ dimmers provide the best dimming performance for LED bulbs while setting the right light level to improve mood and ambiance for any activity. Designed specifically for dimmable leds and CFL, as well as for use with traditional incandescent and halogen bulbs, they greatly improve the dimming performance when compared to standard dimmers. Featuring advanced circuitry designed to alleviate common challenges, like flicker and pop on, LED+ dimmers are compatible with 800+ bulbs - for more specific details on compatible bulbs, view "technical specification" below. The Toggler dimmer matches existing toggle switches and fits in a standard wall plate (fg-1-wh). it features a toggle switch that turns the lights on/off and returns them to your favorite preset setting, along with a discreet slider that brightens or dims the lights to suit any activity. This Toggler multi-pack included Toggler LED+ dimmers, wall plates sold separately.

• Tested on 1, 000s of bulbs and dozens of brands for flicker-free dimming. For list of recommended bulbs view "Technical Specification"
• Provides over 250 lighting levels so you can create the perfect light for any activity
• Works with up to 150 Watts of dimmable LED/CFL bulbs or 600 Watts of Incandescent/Halogen bulbs
• Lutron patented technology to optimize the dim range of your bulb and prevent interference with other dimmers in the home
• Can be used in single-pole or 3-Way applications, where lights are controlled from one or two locations
• Includes Lutron Toggler LED+ (formerly C.L) Dimmer Switches; coordinating wallplates sold separately

User questions & answers

Question:	Can this dimmer be used for xenon lights? If not, what type do I need
Answer:	Hello, Yes these are brand new and in original packaging
Question:	i have two black wires, 2 red wires and a ground going into the one I am replacing, this only has 3 hookups, any way around this
Answer:	The unit that we have Current version on the switch that we are selling. Version (YA.15.12.2007) Reset to factory default setting These switches can be upgrade and or down graded by logging into Aruba's web site. There may be a charge, but I am not sure about that.
Question:	Anyone know the difference between the "Ariadni" switch (AYCL-153P) and the "Toggler" switch (TGCL-153P
Answer:	Yes, have problem on the keyboard, yes.
Question:	Can this be used (minus plate) to replace 1 switch in a 3 or 4 switch box? Will the actual switch plus dimmer lever be too wide for the plate hole
Answer:	It's a volume control wheel.

Product features

Cutting Edge Technology

Our patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Fast and Easy Installation

All you need to replace your existing switch or dimmer is about 15 minutes, 3 simple steps and 1 screwdriver

Works Well with LEDs

Tested on 1,000’s of bulbs and dozens of brands to ensure flawless dimming. Check out our website for our list of recommended bulbs

Product description

Control the next generation of lighting with Lutron's dimmable LED+ dimmers! Screw-in dimmable compact fluorescent lamps (CFLs) and screw-in dimmable light emitting diode lamps (LEDs) are a great energy-saving alternative to incandescent or halogen light sources; however, dimming them may be difficult. Lutron's new line of LED+ dimmers provides a solution to alleviate your dimmable CFL and LED dimming challenges, while allowing you to adjust the light level to improve mood and ambiance. with the same features as the original slide dimmer by Lutron, this Skylark dimmable CFL/LED dimmer features an easy to use slide control that adjusts the light to suit any activity, and a convenient switch that returns light to your favorite level. These dimmers still provide full-range dimming for halogen and incandescent bulbs, ensuring today's dimmer is compatible with tomorrow's light sources. The dimmer can even dim a mixed load of light sources (i.e. LED and halogen or CFL and LED bulbson the same circuit). Claro wallplate is not included.

• Tested on 1,000s of bulbs and dozens of brands for flicker-free dimming. For list of recommended bulbs view Technical Specification
• Provides over 250 lighting levels so you can create the perfect light for any activity
• Works with up to 150 Watts of dimmable LED/CFL bulbsor 600 Watts of Incandescent/Halogen bulbs
• Lutron patented technology to optimize the dim range of your bulbs and prevent interference with other dimmers in the home
• Can be used in single-pole or 3-Way applications, where lights are controlled from one or two locations
• Rocker switch turns lights on/off to favorite light level. Discreet slider dims and brightens the lights
• Includes Skylark LED+ (formerly C.L) Dimmer Switch; coordinating wallplate sold separately

User questions & answers

Question:	How do I wire this with no ground
Answer:	Note 4 of the installation instructions states: When no "grounding means" exist in wallbox, the 2011 NEC allows a control to be installed as a replacement if 1) a nonmetallic ,noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a GFCI. When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.
Question:	So I have two can light led’s wired to a 2 toggle switch plate, can I remove the light receptacle and replace with this to dim the lights
Answer:	As long as the LEDs you are using are compatible with this dimmer, then yes it will work properly for your application. For more information on compatible LED lamps, Lutron would reccomed checking out their LED tool at Lutron.com/ledfinder.
Question:	Can i use 2 of these to dim from either location on a 3way (currently an old skylark and an on/off switch)? or do i need a maestro setup
Answer:	On 3-way circuits, only one ELECTRO-MECHANICAL switch can be a dimmer regardless of lamp type, other switch must be standard single-pole 3-way on/off. You CAN use DIGITAL ELECTRONIC CONTROL SYSTEM (ie: MAESTRO) for all switches on circuit. Skylark SCL-153P dimmer is "electronic" but it is not a CONTROL SYSTEM that encompasses the whole circuit.
Question:	Can this dim incandescent and LED bulbs on the same circuit
Answer:	Yes- the issue is that the bulbs are very different and as a result will not dim uniformly so when dimmed one may be brighter

Product features

Cutting Edge Technology

Our patented easy-to-set adjustment lever allows you to change the low end of dimming and set the optimum dim range for your bulbs.

Control up to 17 Bulbs

Each Lutron LED+ Dimmer can control up to 17 bulbs, and is the only dimmer UL listed to control mixed loads (different types of bulbs, such as LEDs and halogens, on the same circuit)

Fast and Easy Installation

All you need to replace your existing switch or dimmer is about 15 minutes, 3 simple steps and 1 screwdriver

Works Well with LEDs

Tested on 1,000s of bulbs and dozens of brands to ensure flawless dimming. Check out the Lutron website for our list of recommended bulbs.

Product description

Wi-Fi Enabled Smart Dimmer Switch with brightness control. Note1: Requires neutral wiring. If no neutral wire is present, the installation cannot be completed. Note2: Works in single pole wiring only. Note3: Requires a secured 2.4 GHz wireless home connection. Please consult a professional electrician if you are unfamiliar with basic electrical wiring.

• Control from anywhere: Turn electronics on or off from anywhere with your smartphone using the case app (Compatible w/ Android & iOS)
• Voice Control - Works with Amazon Alexa, Google Assistant and Microsoft Cortana supported devices for a hands-free experience
• Gentle off - Tailor your lighting to fade on with a click of the switch or a double-click to gently fade off the lights while your child drifts off to sleep
• Scheduling - Use Schedules to set your smart switch to automatically turn on and off while you're home or away
• Note: Requires a neutral wire / Works in a single-pole setup only / Secured 2.4 GHz WiFi network connection

Product features

Start Dimming

The Kasa Smart app guides you through each step of the wiring process and helps you connect to your home Wi-Fi. You can control the brightness of lights, set schedules, or include with other devices in Kasa lighting scenes to set the perfect ambiance. The Kasa Smart app gives you the ability to monitor and control your smart dimmer from anywhere.

What is a neutral wire?

A neutral wire allows Kasa switch to be powered while simultaneously allowing the lighting circuit connected to your lights to be power off.

Control Your Dimmer from Anywhere

With the Smart Wi-Fi Dimmer, you can control the ambiance of any space with the push of a button. Plus, easily control it from anywhere using the Kasa app or your favorite voice assistant device.

Gentle Off

Use 'Gentle Off' to fade off the lights in your child's bedroom as they drift off to sleep or allow yourself time to exit a room without bumping into something in the dark.

Brightness Control

Control the brightness of lights in any room and set the ambiance for any activity. Designed to dim today's energy efficient LEDs as well as traditional incandescent bulbs.

Scheduling

Use 'Schedules' to set your smart dimmer switch to automatically turn on and off while you're home or away. With IFTTT or Nest, you can set your device to turn on and off depending on your location.

Set Scenes

Group your smart dimmer switch with other Kasa devices to create 'Scenes'. Have it be a part of a scene for when you wake up, go to bed, or one to make it look like you're home even if you aren't.

Control with Your Voice

Set lighting levels using voice control with an Amazon Alexa, Google Assistant or Microsoft Cortana supported device.

Your Home. One App.

The Kasa app works with all TP-Link smart home devices, allowing easy control of your home from your Android or iOS smartphone.

No Hub Required

The Smart Dimmer connects to your secured 2.4 GHz Wi-Fi network. No need for a separate smart home hub.

• Dimmer Switch: TOPELE in wall dimmer switch is work with LED dimmable lighting,dimmer adjustment allows you to optimize the range from low to high brightnss, works well and have a small hidden switch to adjust the brightness level of the bulbs
• 3 Way and Single Pole: Good dimmer for LED lights, can be used in single-pole or 3-way applications, it is really aesthetically clean lines and smooth dimming operation of dimmers.
• Slide Control Dimmer: with the on/off rocker switch and discreet slider, it is smooth and easy to adjust the brightness, works great as a dimmer of LED kitchen light, dining room light fixture
• Work Great with Varying Dimmable lights: Compatible with 600W incandescent, 150W LED, 120VAC, 60Hz, full range dimming for incandescent, dimmable LED and CFL, extra knob under the cover that set the brightness you prefer
• UL cUL listed, 1 year warranty, please feel free to contact us if you have any dimming issues

User questions & answers

Question:	is the green color in the slide adjuster fluorescent in the dark
Answer:	This lamp has a regular plug that is 2 pronged. It should fit into any standard outlet.

Product features

TOPELE 3-Way Single Pole Dimmer Switch

TOPELE dimmer switch is the great dimmer to adjust brightness, the smooth discreet slider is very tiny, that you can brighten and dim the lights you want. On the one side of the switch, there is the extra adjustment dial, you can adjust the dimming levels, create the comfortable home experience for you

Range of bright to dim

0-100% dimming range, and fast reach 50% brightness,the brightness can be adjusted depend on your different requirement, dim the light when sleeping, watching movies, and brighten it when working, reading. Set dimmer to the level you need

Smooth Switch to control

The paddle sits flush with surface when the switch is off, looks better in most time of a day. The smooth slider allows you to optimize the range from low to high brightness

Ease of installation

Installation is easy-- Black wire replaced by new dimmer black wire, Green wire replaced by new dimmer black wire, and the red wire without tap replaced by red wire, if 3 way switch, use both red wires on new dimmer to replace previous dimmer’s two red wires

Troubleshooting with Side Adjuster Wheel

• Bulbs do not work while being dimmed.
• Bulbs flash or flicker in low dimming level

Solution:

1. Make sure that all bulbs are dimmable
2. Remove wallplate and find out the adjustment knob
3. Tune up the adjustment dial until without flash or flick
4. Install the wallplate

Product description

Leviton Decora SureSlide dimmers provide smooth, slide-action, full-range dimming for incandescent and dimmable LED and CFL lamps. Featuring a pre-set On/Off switch, this device allows the user to set the desired brightness level to operate automatically with the On/Off function. The dimmer is designed specifically for dimmable light-emitting diodes (LED) and dimmable compact fluorescent (CFL) lamps; It is also compatible for use with incandescent lamps. Note: Flickering means that the bulb being used is not compatible with our device. In the technical specifications section, the application guide is a list of bulbs that Leviton has confirmed will work with our device. Kindly refer this guide for better use.

• Future proof to control a variety of dimmable CFL and LED lamps
• Integrated linear full range slide control for easy, precise operation
• Backwards compatible with incandescent lamps
• CFL mode for dimmable CFLs; This feature provides a higher starting voltage that is required for many compact fluorescent lamps
• LED/Incandescent mode provides optimized dimming for LED lamps and for incandescent operation
• See LED bulb compatibility in the technical specifications below (comparison chart PDF)
• Wallplate sold separately

User questions & answers

Question:	I plan on using this with a track lighting kit that uses dimmable leds. do i need anything (transformer?) between this switch and the track fixture
Answer:	It would depend on the rack light system you use. If it uses 120v lamps then no. if it is a lower voltage lamp system it would have its own transformer as part of its installation and this dimmer is probably not what you need. You would then want a dimmer designed for low voltage applications. As far as I know though there is no hard and fast rule on this today as all the dimmers and transformers are electronic and may or may not be compatible with other electronic devices including the led drivers fjord the particular lamps in the track system you select. You should consult with the dealer you ate purchasing from and the installing electrician. If you ate doing it yourself you'll need do your research through the manufacturers of the equipment for comparability like the electrician would.
Question:	What size bulb can be used with this dimmer? There seem to be all kinds of size bulbs available
Answer:	That's right in the description: 150 watts LED / CFL, 600 watts incandescent. Just add the power requirements of all the bulbs controlled by the dimmer. For example, I'm using it to control 4 60 watt incandescent bulbs, total 240 watts. For LEDs / CFLs, use the actual power required, not the "equivalency". So a 23-watt CFL that says it's as bright as a 100 watt incandescent still only counts as 23 watts.
Question:	difference in led and incandescent lighting dimmers
Answer:	Some incandescent dimmers modify the output of the power in such a way that it either won't work at all or can damage the LED dimmer. LED dimmers I believe use finer PCM (Pulse Code Modulation) which will work with all dimming bulbs - incandescent, CFL, and LED bulbs. Using LED bulbs with a non-LED dimmer is a bad thing as is using LEDs that are not designed to be dimmed at all. The payback for the additional expense of the LED dimmer is pretty quick if it removes a large enough incandescent light bulb.
Question:	Led dimmable bulb is flickering with this switch, is it bad
Answer:	Problem: Flickering or FlashingPossible Cause #1: Incorrect VoltageLED downlights have a specified input voltage. Incorrect voltage to the driver can cause the LED to flicker or toflash on and off. * Check the input voltage of the driver (Ex: 120V) then check the voltage being delivered to the fixture (Ex: 277V). There may be a mismatch. If possible, replace the driver on the downlight for one with the correct input voltage to match the line voltage or, if that is not an option, install an applicable voltage transformer to the line voltage to achieve the required input voltage for the original fixture.Possible Cause #2: Incompatible DimmerIf the LED downlight was not designed for a particular dimming load or if the driver is not compatible with thedimming control then issues may occur. * Try bypassing the dimming circuit. If the LED functions normally then an incompatible dimmer or dimming load may be the issue or the driver is not a dimming driver. Consult factory to determine whether the driver is dimmable and, if so, what kind of dimmer is compatible with the driver. Please check this web link for a list of factory qualified compatible dimmers: http://www.liton.com/webcatalog/brochures/wp_dimmingfacts.pdfPossible Cause #3: Occupancy Sensor/Control Rated WattageThese controls sometimes have a minimum rated wattage in order to function correctly. For example, theremaybe a minimum of 20W required for the control unit but the LED might only consume 10W. * Add additional fixtures to the circuit to get to the required wattage for the dimming control or replace the dimming control unit with one that has a lower wattage requirement.remedyremedyremedycontinue...TROUBLESHOOTINGLED DOWNLIGHTSA DIVISION OF EEMA LIGHTING GROUP * 5461 WEST JEFFERSON BLVD., LOS ANGELES, CALIFORNIA * PH: 323.904.0200 (1 800 515 4880)FAX: 323.904.0201 (1 800 972 4880)Problem: Flickering or Flashing cont..Possible Cause #4: Dimmer OverloadA common problem with LED dimming is the inadvertent overloading of the LED driver. LED drivers are rated fora maximum load (measured in volts, amps and/or watts) that must not be exceeded.The number of lamps that can be installed on a single-phase control dimmer may seem to be an easy calculation.For example, suppose you want to know how many 15W LED fixtures can be installed on a 600W dimmer. Youmight divide the 600W by 15W and determine that you could control 40 fixtures. Unfortunately, that result mightbe wrong. In fact, you may only be able to use 6 LED fixtures on a dimmer rated for 600W.Even though the LED fixture may draw only 15W continuously, there may be a start-up in-rush current or arepetitive half cycle surge that makes the dimmer think that the current is much higher. That 15W LED fixturemay appear to the dimmer as a 100W incandescent load. If that happens and you are using more than 6 LEDfixtures, you will overload the dimmer.The average start-up or half-cycle stress that has been observed is the equivalent of a 100W incandescent lamp,even for LED loads of less than 20W! * For 10W & 15W Liton -DLV products, consult the charts in the LED Dimming Facts Guide to reference tested maximums by dimmer. * Remove the dimmer from the line to see if the problem is solved. * Change dimmer to one with a higher maximum load. * Split the circuit into multiple loads.Possible Cause #5: Dimmer UnderloadSome dimmers may not perform well if too little load is put on them. A minimum number of fixtures may berequired to operate correctly due to the 25W - 40W minimum load that most incandescent dimmers require tooperate correctly under all conditions. When using incandescent bulbs, the minimum load requirement waseasily met. However, with LED four or more loads may be required for a dimmer to reach the required minimumload. * For 10W & 15W Liton - DLV products, consult the charts in the LED Dimming Facts Guide to reference tested minimum by dimmer. * Remove the dimmer from the line to see if the problem is solved. * Change dimmer to one with a lower minimum load.

Product features

Multiple Locations

Perfect in large areas or hallways/staircases that have two switches that control the same light(s).

Leviton Dimmers Put You In Control

Set the mood by adjusting the light level for any activity. Whether you are entertaining, reading, keeping the little ones safe from bedtime “monsters” or watching the latest flick, you're in control.

Superior Performance

Take advantage of the full dimming range of your bulb by adjusting the minimum light level on the dimmer.

Compatibility is Key

To achieve the best dimming performance, ensure that the bulbs are compatible. Download the “comparison chart” in the technical specification section below to see the best pairings for this dimmer.

Product description

This is a single pole/3-way 120-volt LED-compatible dimmer switch. It is a decorative slide dimmer light switch with an independent On/Off switch and 600-watt capacity. This dimmer switch features a trim dial beneath the cover plate, which allows for sensitivity adjustment during installation to achieve compatibility with LED lamps. Easily turn your lights on and off using the rocker switch and automatically return to your previously selected light level of brightness.

• 3-Way and Single Pole Compatible - Horizontal Slide control dimmer
• 600W max Incandescent; 150W max Dimmable LED/CFL,120VAC, 60Hz
• Works with LED, Halogen, Incandescent bulbs - Trim Dial below Cover Plate allows Sensitivity Adjustment upon installation to achieve compatibility with LED Lamps
• Wall Plate and Mounting Screws Included
• UL Approved, 1 Year Warranty

User questions & answers

Question:	What are the sizes of the wire gauge? 10 awg or 12awg
Answer:	Yes this will fit your vehicle.
Question:	where is the light almond ones
Answer:	Yes this will fit your vehicle.
Question:	Is this dimmer elv
Answer:	Yes this will fit your vehicle.
Question:	Can you use if on a ceiling fan individually
Answer:	No you need 9006 for your vehicle.