13 best phase angle controllers

Product description

Description:Aluminum heat sinks provide long-lasting use, which helps to dissipate heat and protect solid state relays. Solid state relays are ideally suited for automated process control applications and are essential components for temperature controllers and other mechanical control systems. Made of durable aluminum material, installable heat sink design, small size, easy to install. Solid state relays are not included here.

• Product Name: Aluminum Heat Sink;Material: Aluminum; Color: Black
• Applies to: Single Phase Solid State Relays 10A,25A,40A
• Radiator size (approx.): 80mmx 50mmx 50mm/3.1" x2.0" x2.0" (L*W*H)
• Note:Need to be evenly coated with thermal grease between the solid state relay and the heat sink.
• Package contents: 1 x aluminum heat sink

User questions & answers

Question:	are relay mounting and heat sink mounting screws included
Answer:	I believe the screws to the heat sink are but not the mounting screws.

Product description

Cedarberg static phase converters are designed to start motors within a specific horsepower range. Smaller motors may be started one at a time, once a motor within the converter horsepower range is running, provided that the smaller motors are wired into the same circuit. Cedarberg rotary phase converters are designed to start any motor from fractional horsepower up to the Nameplate rating. If the motor on the equipment is larger than the phase converter’s Nameplate rating, a phase converter of the correct size will need to be purchased. Do not ATTEMPT to start a motor that is too large for the converter or damage could occur.

User questions & answers

Question:	How many volts
Answer:	240 volt single phase in and 240 volt 3 phase out.
Question:	The machine is a computarized plain socks knitting machine, weilite brand model wlt-6f. the plate only says it is 380v / 50 hz motor power 1.2 kw
Answer:	I did check with our lead technician today. We cannot support 380V with our phase converters. We can only support 220V as previously mentioned.
Question:	can use this equipment to conect with one Voltage regulator of 3 phases
Answer:	Good afternoon and thank you for the inquiry. This product is not a good fit for a voltage regulator. It is intended to start 3 phase motors.
Question:	I need to run a 3 phase 240v 20amp tire balancer but I only have single phase 220 can this do that? The motor is 1.5hp
Answer:	If the running amps required are 20 amp then no. You cannot use this converter. This type of converter is used to start a 3 phase motor with less than 6 running amps.

Product description

Parameters:

Operating voltage: DC 5-12V(limit 15V)

Operating current: continuous 1.5A (peak 2A)

Control power: 15W (max rated value)

Static current: 0.005A (standby state)

PWM duty ratio: 1%-100%

Highest speed: about 10000r (depends on the motor )



Attention:

1. The motor controller is designed with input reverse connection protection. Please use it for motor with applicable parameters, or the chip will be burned. There is LED indicator if motor unmatched.

2. There are three-wire brushless motors and four-wire brushless motors, if used for three-wire brushless motor, three wires directly connect to the module terminals W, V, U separately, on need to distinguish order, but required solid connection. For four-wire brushless motor, there is a COM wire, which is no need to connect to the module. If connect, the module will be damaged.

3. Motors within 7200rpm, input voltage range is DC 5-12V, recommended input voltage with range of DC 5.5-6V for the first testing, then increase the voltage according to the motor working condition. For used motor with small internal resistance, recommend operating voltage DC 5-9V. Motor more than 7200rpm with small internal resistance, recommend operating voltage DC 5-7V, input 12V will burn the module.

4. Please offer pure DC power supply, it will be better to offer current more than 1.5A, the quality of the power supply will influence the performance of the driver module. If the motor cannot start or start difficultly for the power supply, please try another power supply.

• DROK mini sensorless three-phase brushless motor speed regulator using imported chips for wide operating voltage DC 5-12V, please offer only DC power supply, and with sufficient current. It is used for three-phrase brushless motor with power no more than 15W. Not suitable for brushed motor.
• Motors within 7200rpm, input voltage range is DC 5-12V, it is recommended input voltage with range of DC 5.5-6V for the first testing, then increase the voltage according to the motor working condition. For used motor with small internal resistance, recommend operating voltage DC 5-9V. Motor more than 7200rpm with small internal resistance, recommend operating voltage DC 5-7V, input 12V will burn the module.
• There are three-wire brushless motors and four-wire brushless motors, if used for three-wire brushless motor, three wires directly connect to the module terminals W, V, U separately, on need to distinguish order, but required solid connection. For four-wire brushless motor, there is a COM wire, which is no need to connect to the module. If connect, the module will be damaged.
• The motor governor is with phase loss protection, if the motor line loss phrase and influence the rotation, there will LED indicator. Please note it can't in the state for long time, or the board will be burned.
• The BLDC controller input side is designed with reverse polarity protection, over current protection.

Product description

Package: 

1 x 4KW 220V VFD Inverter 

1 x 2M Extension cable/control panel box 

1 x English user manual will send by amazon email

Feature: 

1) PID control; advanced calculus PID closed-loop arithmetic, 

2) Easy PLC function and inverter control function

3) Control Mode: V/F, Sensorless Vector Control (SVC), Torque control; 

4) Low output ratting torque 0.5Hz-150%; 

5) Carrier adjustable by 16KHZ Tech parameters: 

6) Input Voltage: 220V(+/-15%) 

7) Output Voltage: 0-220V 

8) Input Frequency: 48-63 Hz 

9) Output Frequency: 0-400 Hz 

10) Input Phase: 1 or 3 phase 

11) Output Phase: 3 phase 

12) Current: 18A 

13) Power: 4.0Kw

• Model:HY 4KW 5HP Inverter VFD 220V;Power:4KW
• Input voltage:single phase or three phase 220V 60Hz;Output Phase:3 phase
• output frequency:0-400hz ; Output Type:Triple
• Cable:parcel include 2m extension cable/control panel box
• Output Current:18A；this VFD can not install brake resistor.

User questions & answers

Question:	I need to control startup acceleration (timed is OK) and remote run/stop-jog would be nice but not required. Will this vfd accommodate that
Answer:	Yes you can control start up. The start up ramp that is in the vfd from the factory is very long ramp, i do not remember the time but at first i thought it was not working. You will have to shorten it. The instructions were easy to follow.
Question:	If commercial power goes out, will the vfd require reprogramming or are settings saved to a prom
Answer:	If a power loss happens all programming is saved.
Question:	I need 220volts single phase and output of 220 volts 3 phase for my 5hp horse power submersible pump.. is this the right one
Answer:	yes it is. Did you read the description? 4KW 5HP Inverter VFD 220V;Power:4KW Input voltage:single phase or three phase 220V 60Hz;Output Phase:3 phase. Now if you are not into electricity. meaning electrical engineer or at least an electrician, Do not kill yourself and get someone that knows what they are doing. Three phase power is not for DIY
Question:	Does anyone have a copy of the manual for this unit. Thx
Answer:	You can download user manual from below link,thanks! https://drive.google.com/file/d/0B49xwe9ffk3fZ3VWR3NHMjB6VkU/view?usp= sharing

Product description

DC Motor Speed Controller, 24V-90V Adjustable Single Phase Motor Speed Controller for 24V, 36V, 90V DC motors



This DC Motor speed controller is made with high quality electronic circuit and integrated components which ensures a longer service life. Widely used for speed governing device drivers of packaging, printing, electronics, instrument meter, clothing machinery, medical machinery and other industries. If you have any issue about the item, please contact us by e-mail, we will try our best within 24 hours to reply



Specifications:

Input Voltage: AC 110V

Control Motor Power: 0.02W~400W

Output Voltage: DC 24V~90V

Size: 11.2 × 10 × 6cm/4.4 × 3.9 × 2.3in



Package Includes:

1 × Speed Controller

    

• ☆ 【Single Phase Controller】: This DC motor speed controller 24V is only suitable for the motor below 1800rpm. A single-phase asynchronous motor speed controller and can be used for 24V, 36V, 90V DC motors. Input Voltage: AC 110V; Control Motor Power: 0.02W~400W; Output Voltage: DC 24V~90V
• ☆ 【High Precision】: Motor speed controller 36V has small size, high precision, wide speed controlling range, low power consumption and long service life; Size: 11.2 × 10 × 6cm/4.4 × 3.9 × 2.3in
• ☆ 【Fast To Respond】: DC motor speed controller is used with single-phase asynchronous motor to realize feedback constant speed and stepless speed regulation. It feels smooth and has good durability
• ☆ 【Wide Application】: Adjustable DC motor speed controller 90V can be widely used for speed governing device drivers of packaging, printing, electronics, instrument meter, clothing machinery, medical machinery and other industries
• ☆ 【High Quality Circuit Board】: This motor speed controller 24V uses high quality electronic circuit and integrated components, sturdy, not easy to aging and abrasion resistant, to ensure maximum strength and durability for long lasting usage

User questions & answers

Question:	how do you adjust the output voltage
Answer:	The knob on the front. It's essentially a potentiometer. I orders this one for a 90v treadmill motor an it works great.
Question:	Will this work on a treadmill motor? I don't see an amp rating
Answer:	This DC motor speed controller is suitable for 24V/36V/90V treadmill motor. Amp rating is 4A.
Question:	I need a motor speed controller for this unit: bestequip 500w 36v 500rpm brushless motor 10.8a geared motor " do you sell one
Answer:	according to literature in add it says 400 Watts max so i would say no

Product description

Descriptions:

This speed controller switch is for 3-Phase brushless motor, and support motor CW CCW, stable performance, simple and most cost-effective multi-function operation.The speed of the motor can be regulated by the potentiometer, easy to use.



Specifications:

Input voltage: DC5-36v

Output current: <15A

Protective current: 15A

CW CCW: support

Speed regulating mode: potentiometer (270 degree linear)

Speed adjustment range: 0-100%

support for Motor: brushless motor

Connection type: fence type terminal

Knob specification: 100K (with switch)

Module size: 8 x 6 x 2.8cm/3.15 x 2.36 x 1.1inch

Weight: 87g



Package Included:

1 x Motor Speed Controller



Note:

1.The input voltage must be divided into positive and negative and cannot enter 220V home power

2.The input voltage shall be equal to the rated voltage of the motor (5-36v).

3. Motor line ABC,no sequence of distinction

• ★ADVANTAGE: This speed controller switch is for 3-Phase brushless motor, and support motor CW CCW Stable performance.
• ★FOR CONTROLLING THE DC MOTOR SPEED: This motor speed controller is 15A power speed controller, mainly used for controlling the dc motor speed.
• ★HIGH QUALITY: The input voltage is DC5-36v, it has an accuracy circuit design, high efficiency, and high quality.
• ★EASY TO USE:Simple and most cost-effective multi-function operation. the speed of the motor can be regulated by the potentiometer.
• ★SATISFACTION GUARANTEE: We care for every customer’s feeling.If this product does not meet or exceed your expectations,please send it back for a 100% refund no questions asked.

Product description

Specifications:

This controller uses novel bi-directional high-power SCR. It can be very convenient adjust the current up to 25A, and solve the over current problem of the heating wire resistance is too small in the case of cooling causing good.

The output voltage is adjusted anywhere between 50V-220V for use with electrical appliances. It can use to such as electric stove, water heater tune thermal, lighting dimmer, small motor speed, electric iron thermostat, and achieve dimming, thermostats, pressure regulator effect.

100% brand new and high quality.

Input supply voltage: 110V ~ 250V AC

The output voltage:50V-250V

The maximum output power: 2000W

The maximum output current :25A The voltage regulating range:50V-250V AC



Before you attempting to wire the controller, make sure all power is disconnected.

1. Cut any one of the battle line or zero line of the lamp or electrical appliances, and connect wires refer to the “wiring diagram” (NO.7 picture)

2. Turn on the power, and adjust the potentiometer.



Package Include:

1pc * 50 - 220V 25A AC Motor Speed Controller

• Input supply voltage: 110V ~ 220V AC
• The output voltage:50V-220V(Output voltage < = Input supply voltage)
• The maximum output power: 2000W; The maximum output current :25A
• Item size: 1.85*1.38*1 inches; Net weight: 1.76 ounces
• Operation environment temperature:-20'C-40'C;High efficiency,high torque,low heat generating

User questions & answers

Question:	How do i wire this for 110? there is an in-n, in-l, out-l, out-n. i connected this on the hot leg to the in-n and out-n. fan runs but no speed change
Answer:	I used mine for varying the speed of a series wound "universal" motor. A motor with brushes and commutator. It worked to vary the speed. I wired it with the two terminals closest to the heat sink to the 110 the two closest to the variable resistor to the motor.
Question:	Which of the 4 screws are power/ground and in/out? They are not labeled
Answer:	I believe you want to know which terminal is power and neutral. Ground is not connected to any terminal, ground would be connected to the frame of the enclosure. This is an AC device, not DC. If you look on the printed circuit side of the board you will see one wire trace goes directly from one terminal to another terminal and no place else, those are the two neutral terminals. Refer to the diagram for line (input) and load (output) terminals.
Question:	Will this work in a led dimming circuit, between the ac mains and a dim able led driver
Answer:	"...LED's do not work with AC current" That is not true. Yes an LED is a diode and only conducts in one direction but that doesn't mean that it won't light up if hooked to an AC source. It will act like any diode and will only conduct on one half of the AC cycle. The 2 things to be considered are: 1. What is your "dim able led driver"? Is it meant to be driven by standard AC house current? If so, you're good to go. If it's expecting DC, then it might work but will only work with one half of the AC cycle. 2. The LED may produce light that is strobing at 60 cycles since it's off half the time. Not good for lighting. Great for headaches. Bottom line get a standard light dimmer switch.
Question:	Will this work to dim some 500w halogen work lights
Answer:	I think the answer would be "yes" with some constraints. "Yes" in that my experience has been it overheats at half the 2000 watt rating, but 500 watts should be OK. You should read up on halogen bulbs because unlike tungsten filament bulbs, halogens need to be operated at a certain minimum temperature. You should be able to dim them down to about 70% duty cycle as long as you also operate them at 100% for substantial periods at other times. Otherwise, I think you may have some condensation of tungsten on the glass tube surface. But as far as the wattage is concerned, this device should be ok t 500 watts. If you exceed its capacity it will have thermal shut down until it cools off. You won't have a huge investment if you decide to try it -- either in the PWM device or the tungsten bulbs. Just make sure you don't go below 70% duty cycle and check the bulb surface from time to time for evidence of metal deposits (silvering) and run at 100% duty cycle for a time to remove it. Good luck.

Product description

Specifications:

Rated Voltage: DC 6-12.8 V (12 V suggested, no higher than 12.8 V)

Rated Current: 32 A(no higher than 40 A)

Rated Power: 5 V 0.5 A

Temperature Protection: 110℃                  

Speed Control Range: 8%-98% 

Suitable Number of Poles: 2-18

Startup Methods: Flexible slow startup/direct startup

Braking Mode: Reverse load braking/without braking

Speed Control Signal: 8 KHz / 16 KHz  fixed frequency PWM

Steering Gear Test Function: Below 55 g

Packaging list:

1 x Speed Controller

• SAFETY STARTUP -- To avoid any injury, the motor will not start up immediately if the potentiometer of speed controller is not at the lowest gear, which is necessary for high-speed high-power motor to protect user's safety.
• TEMPERATURE PROTECTION -- The speed control has aluminum heat sink, which allows it work at 30 A continuously.
• When temperature reaches 110℃, temperature detect system will send a protection signal and system will auto decrease 60% power output to protect speed control and motor.
• POWER IDENTIFICATION SYSTEM -- The speed control has power identification system, which is designed for high-speed high-power motors such as in model plane. It is not suitable for low-power brushless motors.
• THE SIGNAL LOSS PREVENTION -- Auto shut down when there is no signal detected from PWM signal generator(potentiometer ).

Product description

Enjoy the full-size controller experience in handheld mode with the HORI Split Pad Pro! Featuring full-size analog sticks, a precision D-pad, and large shoulder buttons designed for comfort and accuracy, even during marathon gaming sessions. Advanced features include assignable rear triggers, Turbo functionally, and more. Perfect for high-pace action titles and many other genres. Enhance your gaming experience with the Split Pad Pro! (Does not include Motion Controls, HD Rumble, NFC, or IR camera.) Officially Licensed by Nintendo

• Full-size Controller experience in handheld mode
• Larger grip, Buttons, triggers, analog sticks, and d-pad
• Assignable rear triggers, Turbo functionally, and more
• Translucent Black design
• Officially Licensed by Nintendo

User questions & answers

Question:	Can you take the two halfs and fit them together as one single controller? If not, I think that'd be a really cool future upgrade, so there's an idea
Answer:	Alan W. No because the pro controller doesn't also connect to the switch Personally I think these are overpriced seeing as wired controllers generally sell for $20-$30 while wireless sell for $30+ These are equivalent to wired controllers so...
Question:	Is there plan to sell a case to fit this
Answer:	ButterFox has a case that is made to fit the Switch with these controllers attached https://www.amazon.com/dp/B0899NBQVV/ref=cm_sw_r_cp_apa_i_weQvFbE7PXKMN
Question:	Can they be used detached from the switch
Answer:	If you use the grip that comes with the Switch, and plug in the USB I don't see why it wouldn't work. You would have to remove "grip" part from the bridge though. You can unscrew it. There are 3rd party power grips as well..
Question:	Do these have HD Rumble
Answer:	Sadly not. Though I wish games put more effort into the rumble. No game treats it beyond an after thought. So you don't miss out much.

Product description

DC Motor Speed Controller, 24V-90V Adjustable Single Phase Motor Speed Controller for 24V, 36V, 90V DC motors



This DC Motor speed controller is made with high quality electronic circuit and integrated components which ensures a longer service life. Widely used for speed governing device drivers of packaging, printing, electronics, instrument meter, clothing machinery, medical machinery and other industries. If you have any issue about the item, please contact us by e-mail, we will try our best within 24 hours to reply



Specifications:

Input Voltage: AC 110V

Control Motor Power: 0.02W~400W

Output Voltage: DC 24V~90V

Size: 11.2 × 10 × 6cm/4.4 × 3.9 × 2.3in



Package Includes:

1 × Speed Controller

• ☆ High Precision: Motor speed controller has small size, high precision, wide speed controlling range, low power consumption and long service life; Size: 11.2 × 10 × 6cm/4.4 × 3.9 × 2.3in
• ☆ Wide Application: Adjustable DC motor speed controller can be widely used for speed governing device drivers of packaging, printing, electronics, instrument meter, clothing machinery, medical machinery and other industries
• ☆ Single Phase Controller: This DC motor speed controller is a single-phase asynchronous motor speed controller and can be used for 24V, 36V, 90V DC motors. Input Voltage: AC 110V; Control Motor Power: 0.02W~400W; Output Voltage: DC 24V~90V
• ☆ High Quality Circuit Board: This motor speed controller uses high quality electronic circuit and integrated components, sturdy, not easy to aging and abrasion resistant, to ensure maximum strength and durability for long lasting usage
• ☆ Fast To Respond: DC motor speed controller is used with single-phase asynchronous motor to realize feedback constant speed and stepless speed regulation. It feels smooth and has good durability

Product description

The Strike Pack device is the most effective way of adding two additional paddles to any official standard PS4 controller without voiding your warranty or making any permanent changes. No longer is there a need to buy expensive custom controllers and the subsequent costly replacements. With the Strike Pack you can map any controller button to any of the two paddles, take advantage of built-in MODS and enjoy a gaming experience on a whole new level. Ease of use is the hallmark of the Strike Pack device. Simply attach the Strike Pack onto your PlayStation 4 controller and enjoy the benefits of extra paddles and built-in MODS. Do you want to go beyond basic functionality? Then download the Mod Central Windows software available through the Collective Minds website to expand the functionality of the Strike Pack and expand all the customization options that are available.

• BUTTON RE-MAPPING - Assign any button to the included paddles, at any time. PC not required. Windows (7 and higher supported) Configuration software also available.
• LAG FREE WIRED CONNECTION - Avoid Bluetooth interference with routers and wireless devices with a 10FT lag free connection for the competitive edge in Online Gaming and Tournaments
• BUILT IN CONTROLLER MODS - Literally hundreds of MOD combinations built right in. Rapid Fire, Burst Fire, Drop Shot, Quick Scope, Auto Run, even Turbo 2.0 and so many more.
• 3.5mm headset audio compatible with controller model CUH-ZCT2 and later.
• Original model CUH-ZCT1 controller NOT supported for 3.5mm headset audio – USB headset required.

User questions & answers

Question:	Will this replace a scuf controller
Answer:	Can work just like a Scuf. Tournament mode has just the paddles activated. Mod mode has the paddles and mods activated. I actually like the paddle placement of this better then my Scuf.
Question:	Will it come with a paper telling me how to activate the mods and do I need any thing to activate the mods like a separate sold wire
Answer:	A short update on this: Collective Minds have been busy making Firmware Updates for the Dominator, so once you've updated the Dominator (1.40), now you actually CAN remap EVERYTHING (except Share and Options) to the paddles, including the PS Button and the Triggers. You can also swap buttons on the fly (X=O or even X=RT) with the built in remapping in Tournament Mode. You need a Windows PC to update the Dominator. For more info, an updated Manual and How-To's visit their website http://collectiveminds.ca/shop/playstation/ps4/strikepack-fps-dominator/ and go to the Downloads Section (scroll down).
Question:	soo... this will work on a regular ps4 controller and will work like a Scuf gamming controller? talking about the paddles
Answer:	The HumanCentric PS4 Mount for PS4 Orginal (2013 - mid 2016 Model) + 2 Controller Mounts Bundle does NOT come with a PS4 or PS4 controllers.
Question:	do you need a pc to map the buttons or can you do it straight threw the ps
Answer:	No cover. It is like a frame

Product features

On the Fly Remappable Paddles

Without the use of Apps or connecting to a PC, the standout feature of the Strike Pack is the on the fly paddle remapping. This feature allows you to assign any button on your controller to either one of the two paddles. Mapping on the fly frees your thumbs and allows you to keep them on the sticks, increasing your response times and giving you a definitive advantage over other players to dominate your gaming sessions.

Ergonomic Design and Responsive Switches

The Strike Pack is precision crafted to fit the official standard PS4 controllers in an ergonomic fashion, giving access to the optimal placement of paddles and a comfortable feel. We focused our efforts on making high quality responsive switches to provide lightning quick response times while maintaining a comfortable and intuitive experience.

Included Mods

The Strike Pack comes pre-installed with many useful and unique MODS to level the playing field and take your gaming to the next level.

Some of the included MODS:

Anti-Recoil Adjustable, Quick Scope, Auto Run, Drop Shot, Rapid Fire, Optimized Rapid Fire, Rapid Fire Adjustable, Pulse Fire Adjustable, Burst Fire Adjustable, MW Jitter, Anti-Recoil, Auto Hold Breath, Turbo Melee, Double Jump, Auto Spot, ADS and Hair Triggers.

Paddle Activated MODS

Map MODS to either one, or both of your Strike Pack’s paddles for quick activation during gameplay. Think of this as a shortcut to performing complex in-game functions, one touch of a paddle and you are given enhanced abilities to eliminate enemies and take control within your games.

Customization for Your Comfort

Detachable magnetic paddles means you can add alternate paddles (available online) for different hand sizes.

Product description

Specifications:

Model: AT1-2200X

Power Source Phase: Single-phase

Rated Voltage: single-phase/3-phase AC220V

Power Supply Voltage: Low voltage

Suitable Motor Power: 2.2kW

Filter: Built-in filter

DC Power Supply Type: Voltage type

Control Method: V/F closed loop

Output Voltage Adjusting Method: PWM control

Rated Current: 12A

Protection: Over-current, over-voltage, over-heat, under-voltage, short circuit protection

Max. Output Frequency: 400Hz

Size: 18*12.5*12.5cm/7.1*4.9*4.9in

Weight: 1.3kg(approx.)

Terminal Instruction:

COM Common terminal 

VI1 External analog voltage input 0-5V/10V analog voltage input CI External current signal input 4-20mA current signal input SP1 Open collector output 1

SP2 Open collector output 2

5V/10V

5V/10V 20mA power supply output TC Relay output 250VAC 5A/30VDC 3A

TA & TB are NC, TA & TC are NO TB Relay output TA Relay output

Note: When adjusting parameter, the VFD must stop working, otherwise it will not be able to save parameter setting.

Package Includes:

1 x Variable Frequency Drive

• ➤【VFD Drive】- This VFD Drive uses unique control method to realize high moment of force, high precision and wide speed regulating range driving, with high performance.
• ➤【Feature】- Variable Frequency Drive has good anti-trip performance and ability to adapt to rough power, temperature, humidity and dust interference, greatly improved stability.
• ➤【PWM control】- By optimizing PWM control technology and electromagnetic compatibility, it satisfies users' requirement of low noise, low electromagnetic interference.
• ➤【Easy to use】- Simple to operate and wire, connect to wires by screw terminals which are more convenient.
• ➤【Design】- VFD Drive is designed with large heat sink for better heat dissipation.

User questions & answers

Question:	Would the current draw on a 3 phase 3 hp motor hooked up to a vfd be the same as the current draw from a single phase 3 hp motor
Answer:	Most likely less of a draw, ours runs 17.5 amps
Question:	Will this run smaller motors say 1 1/2 hp
Answer:	Yes. It will run any motor lower than the rated HP as long as the output voltage matches your motor
Question:	Does this have a remote start input to turn the motor on and off from a relay
Answer:	You can use a remote switch to turn on/ off.
Question:	Do you have a detailed manual
Answer:	Dear, customer Yes, this VFD Drive Inverter comes with paper manual. Thanks! Best regards

Product description

Descriptions:

This speed controller switch is for 3-Phase brushless motor, and support motor CW CCW, stable performance, simple and most cost-effective multi-function operation.The speed of the motor can be regulated by the potentiometer, easy to use.



Specifications:

Input voltage: DC5-36v

Output current: <15A

Protective current: 15A

CW CCW: support

Speed regulating mode: potentiometer (270 degree linear)

Speed adjustment range: 0-100%

support for Motor: brushless motor

Connection type: fence type terminal

Knob specification: 100K (with switch)

Module size: 8 x 6 x 2.8cm/3.15 x 2.36 x 1.1inch

Weight: 87g



Package Included:

1 x Motor Speed Controller



Note:

1.The input voltage must be divided into positive and negative and cannot enter 220V home power

2.The input voltage shall be equal to the rated voltage of the motor (5-36v).

3. Motor line ABC,no sequence of distinction

• DC brushless governor, Hard disk motor controller, Aerospace model motor drive 5-36V
• This speed controller switch is for 3-Phase brushless motor, and support motor CW CCW
• With wide voltage range, DC5-36v, and protective current is 15A. Small size and elegant appearance.
• The speed of the motor can be regulated by the potentiometer, easy to use
• Stable performance, simple and most cost-effective multi-function operation