12 best cue lathe

• This is a upgrade version for pool stick tips not included the glue.
• It can shape the tip into all radians as you like a featue expected by professional players.
• The device can be used on repairing cue diameter from 9.3mm to 13.2mm.
• Don't worry how to use it,each one with a instructions in English.
• It comes with an extra blade.

User questions & answers

Question:	Those who bought one: The Amazon pictures show rusting around the screws (can't believe someone would use a rusty sample), is yours holding up
Answer:	That isn't rust in the picture. It's leftover material from a brown tip that has just been trimmed. You can see it all over the blade just above the screws.
Question:	Can this be used for trimming mushrooming or cutting down an oversize tip from 14mm to 13mm the circumference
Answer:	yes. I trimmed my 14mm tip to 12.75mm with no problem. it is pretty easy with this tool. just make sure you protect the ferrule from getting scratched or cut.
Question:	Can you do kamui clear tips with this tool
Answer:	not sure. I don't do kamui tips, but the tool is designed to do all tips.
Question:	Does tool help with sanding the top of the ferrule flat before tip installation properly and holding tip in place while cement dries? Thanks
Answer:	Yes,It does.You can put it into the diameter control loop,left a little gap for cue to be able to roate.

Product features

All in 1 Pool Cue Tip Shaper

If you don't know anything about tips and using this tool,please read carefully as below:

you need to prepare a new tip and a bottle of glue before using it,you can use a cheap cue tip or old cue to practice to ensure success when you are the first time to do this ,Once you understand how to use it and how to change a tip this truly is a one-stop tool.

1,Tape off your ferrule with masking tape, this will help you avoid extra glue.

2,Be careful cutting the tip off ,Use blade on side of the tool or you can use another razor blade for extra control but don’t get to close to the ferrule.If the tip doesn't cleanly removed,please use the cue repairing kit blade to remove the residual.

3,Use the circle hole (diameter control loop) to shave off the remaining tip and glue on the ferrule.

4,Sand the new tip side that will be glued,ensure the tip surface to be flat.

5,Glue the tip on and be careful to make it even.Hold it down and wait for it to dry (it dries very fast but give it 15-20mins to be safe).

6,Start by trimming the top of the tip on an angle, it will make the final shaping way easier.

7,Carefully trim the sides to be flush with the ferrule. (you can use the main blade of the conical holes to remove extra diameter of the tip,just change the angle of the cue,parallel the taper hole and cue,clockwise rotate) Remove the tape to ensure flushness, then put back on to avoid unwanted debris.

8,Use the curved sand board to shape it to a nickel or dime. This will take a while but be patient.

9,Use the 2 kind of radians alignment to choose the radian what you need,If there is a gap that means the tip radians is not uniform,need further burnish.

10,Use the needle to scuff and poke the top and add some chalk to enjoy your game.

Upgrade Accessiores

Removeable upgrade sets,Used for shape tip to more round better and used for polishing tip edge.

Function A

Professional players,like the top more round the better,you can set it,adjust the position of the slider,directly rotating grinding.

Function B

This groove with a nice sandpaper on the inside,you can use it for polishing tip edge,make it more smooth.

Product description

Turn and support your long slender spindles while eliminating bowing and vibration. The Stead-Fast Steady Rest adapts to any split bed or double rail midi lathe for ultimate control of delicate spindles. Easy installation. Mounts in the channel of any split bed or double rail lathe. When mounted, it sits 12. 75" high from top of lathe bed. Includes all necessary hardware and wrench. non-marking wheels apply multi-point ball bearing spindle support. Adjustable wheel placement allows for spindle support for workpieces down to 1/2" diameter. Great for lots of woodturning projects like baseball bats, table and chair legs, and other long spindles.

• Fully adjustable wheels easily adapt to any position or spindle diameter down to 1/2".
• 3-point ball bearing spindle support.
• Non marring soft wheels.
• Mounts in the channel of any split bed or double rail lathe.
• Compatible with Jet, Delta, and Turncrafter Pro Midi lathes with extension beds.

User questions & answers

Question:	Horizontal thickness. Yes, normally goes on the top of the bed. My bed is round, so it would have to go under the bed with 0.5" clearance
Answer:	Yes, it's a one piece unit
Question:	Will this fit my Rikon mini lathe
Answer:	No, it has a #1 tapered shank. Good only for drill press or lathe.
Question:	Will this work on a Delta
Answer:	Yes, the drill chuck has JT 6 mount (Jacobs Taper 6) on the back and the shank is MT2 to JT6.
Question:	What is maximum? I'll guess and say 6 inches
Answer:	If it is MT2 the dia of the spindle hole of the drill press shall be 0.70".

Product description

This is the video for how to use it: https://www.youtube.com/watch?v=Q03KevOqizM

Description:

This is a mini Buddha bead machine, compact and portable size, powerful woodworking lathe and beautiful appearance.

It also fits other DIY usage such as model,hobby DIY.

Specifications:

Material: Aluminum Alloy + Acrylic

Color: Silver

Plug Type: US Plug

Voltage: AC 100-240V 50/60Hz

Rated Voltage: 12-24V DC

Rated Power: 100W

Rated Speed: 1500-7000RPM

Power: 7 Level of Adjustable Speed

Processing Length: 140mm / 5.51in

Processing Diameter: 55mm / 2.16in

Chuck Clamping Range: 0.6-6.5mm / 0.02-0.25in

Swing Diameter: max 50mm / 2.0in

Grip Length: max 140mm / 5.51in

Matching Saw Blade Diameter: max 50mm / 2.0in

Machine Weight: 1436g / 3.17 lb

Package Included:

1x Mini Lathe Beads Machine

1x Speed Control Power Supply (12-24V)

6x Wood Carving Blade

1x Screw Thread Fixed Needle

3x Hex Shank Fixed Needle

1x Collet Wrench

1x Hexagon Wrench

3x Beads Round Device(12,18,22mm)

1x 50mm Cutting Piece

1x 50mm Diamond Cutting Piece

1x Polishing Plate

5x Polishing Piece

1x Polishing File Tool

1x Mini Caliper

NOTE:

1. If the user does not have lathe base experience, when using, uses should follow: low speed, slowly, cautiously and use other security operations.

2. The speed can be adjusted in 1500-7000RPM, speed of cutting wood should not exceed 4000, grinding can use higher speed.

3. Drill chuck axis, the axis of the wood, the tailstock center axis of the drill should be in a straight line, or need to adjust the nut.

4. If not a cylinder, the speed should be reduced.

5. Tailstock bearing without lock tight.

6. When using a knife, locking the bottom of screw, location should be away from timber 1-1.5cm.

• Specially designed for the home DIY enthusiasts and hobbies,small and portable size with strong power.
• Transparent organic dustproof glass cover with super convective cooling hole, the welding line is covered with a full heat shrinkable tube.
• With 7 levels of power adapter enable you to adjust the rotating speed easily to meet different cutting speed.
• High quality aluminum alloy base and pure steel structure drill chuck.
• Super large torque ball bearing motor, maximum rotating speed up to 7000RPM providing ultra strong cutting power with low noise, you can use it at home.

User questions & answers

Question:	Is this lathe just for producing beads? Or can it be used for other small projects
Answer:	Hello friend, Yes,of course it can be used for other small projects.As long as the the sizes of the tools match your project,this is a DIY tool set.
Question:	Can i make pens and rigs on it
Answer:	NO you can not make pens or rigs, there is not enough power to do anything on it.
Question:	is the plastic cover removable
Answer:	Hello friend, If you don't want the plastic cover,you can disassembly it with the screws.
Question:	I just bought this. How do i get it to fit my 5/8 mandrel. I bought this to make duck calls. But cant figure out what i need to make it fit.what do i
Answer:	Swap out chuck.

Product description

1/3 Horsepower bench top lathe with variable speed motor

• Motor: 1/3 HP, 2 Amp, 110V, Single-phase, 60 Hz
• 12-inch distance between centers
• 8-inch swing over bed
• Cast iron construction and infinitely variable speed control
• Includes two tool rests

User questions & answers

Question:	I have a chuck that is 1"-8tpi female thread (nova 48111), it doesn't fit on this lathe. what adapter should i buy
Answer:	Buy a 3/4" 16 TPI to 1" 8 TPI adapter. If you further questions go to http://www.woodturningz.com/downloads/w1704_ds.pdf for the specs on this machine.
Question:	is there an adapter for the face plate for mounting live center chucks? I bought one but won't line up with holes
Answer:	I'm not sure if they make the adapter to mount on the face plat. I have a 2" diameter three jaw,self centering scroll type chuck that i bought from Amazon that ihave used that works great,but i think that the holes in the face plate is for mounting a backing block to the piece of wood stock to turn a bowl. It says in the manual that you glue the block to the wood your turning and use the holes to screw the block on to face plate. Hope this helped.
Question:	What size wood stock can it hold? How about something like 12'' long by 8" wide piece of wood
Answer:	The length it will hold will be dependant upon what chucks you have in the head and tail stock. The bulkier the chucks, the shorter the length it will handle. I'd say it will hold 12" lengths unless your chucks are sizable. I wouldn't try more than 4" width stock unless it was short. Although the lathe may hold the stock, it would be too much for the motor. The intended purpose of this lathe is to make small things like ink pens, Christmas ornaments, small toys like tops or yo-yo's and tool handles etc. If you want to mount 12" X 8" stock you should be looking at full sized lathes.
Question:	is there anyway to secure to a bench
Answer:	Yes. It has has three holes in the base that you can bolt it down with. I bolted mine down on a metal stand. It holds it down real solid. Mine is the Shop Fox W1704 also. It is well built. I really like mine. Hope this helps!

Product features

Shop Fox W1704 Benchtop Wood Lathe

Tackle pen turning or other small cutting or shaping projects using the Shop Fox W1704 bench-top lathe from Woodstock International. Made of cast iron, and designed to fit neatly on a workbench, this lathe features a 1/3-horsepower, variable-speed motor and delivers spindle speeds between 700 and 3,200 revolutions per minute (RPM). It also features a safety paddle switch, an MT No. 1 spur center, an MT No. 1 live center, 4-1/4-inch and 7-inch tool rests, a 5-3/4-inch faceplate, and a 3/4-by-16-inch TPI RH spindle.

Includes Two Tool Rests

The W1704 includes both a 4-1/2 and 7-inch tool rest for various turning applications and with a 13-inch distance between centers and an 8-inch swing over the bed this lathe is ideal for a variety of turning projects.

Variable Speed

The infinitely variable speed from 700-3200 RPM comes in handy when turning hard or soft species of wood.

5-3/4-inch Faceplate Included

This benchtop lathe includes a 5-3/4-inch faceplate which threads onto the headstock spindle for non-spindle turning (usually used for making bowls or other items that cannot be supported from the tailstock).

Product description

This is the video for how to use it: https://www.youtube.com/watch?v=Q03KevOqizM

Description:

This is a mini Buddha bead machine, compact and portable size, powerful woodworking lathe and beautiful appearance.

It also fits other DIY usage such as model,hobby DIY.

Specifications:

Material: Aluminum Alloy + Acrylic

Color: Silver

Plug Type: US Plug

Voltage: AC 100-240V 50/60Hz

Rated Voltage: 12-24V DC

Rated Power: 100W

Rated Speed: 1500-7000RPM

Power: 7 Level of Adjustable Speed

Processing Length: 140mm / 5.51in

Processing Diameter: 55mm / 2.16in

Chuck Clamping Range: 0.6-6.5mm / 0.02-0.25in

Swing Diameter: max 50mm / 2.0in

Grip Length: max 140mm / 5.51in

Matching Saw Blade Diameter: max 50mm / 2.0in

Machine Weight: 1436g / 3.17 lb

Package Included:

1x Mini Lathe Beads Machine

1x Speed Control Power Supply (12-24V)

6x Wood Carving Blade

1x Screw Thread Fixed Needle

3x Hex Shank Fixed Needle

1x Collet Wrench

1x Hexagon Wrench

NOTE:

1. If the user does not have lathe base experience, when using, uses should follow: low speed, slowly, cautiously and use other security operations.

2. The speed can be adjusted in 1500-7000RPM, speed of cutting wood should not exceed 4000, grinding can use higher speed.

3. Drill chuck axis, the axis of the wood, the tailstock center axis of the drill should be in a straight line, or need to adjust the nut.

4. If not a cylinder, the speed should be reduced.

5. Tailstock bearing without lock tight.

6. When using a knife, locking the bottom of screw, location should be away from timber 1-1.5cm.

• Specially designed for the home DIY enthusiasts and hobbies,small and portable size with strong power.
• Transparent organic dustproof glass cover with super convective cooling hole, the welding line is covered with a full heat shrinkable tube.
• With 7 levels of power adapter enable you to adjust the rotating speed easily to meet different cutting speed.
• High quality aluminum alloy base and pure steel structure drill chuck.
• Super large torque ball bearing motor, maximum rotating speed up to 7000RPM providing ultra strong cutting power with low noise, you can use it at home.

User questions & answers

Question:	Can you use a 3 jaw with this? I want to make resin eggs and cant sand the other side of the egg
Answer:	Dont see why not!!!
Question:	what is the longest piece of wodd I can put in this
Answer:	Hello friend, The longest piece of wood we suggest is about 13cm.

Product description

Remember when you could turn your own pens? Fill your house with as many pens as you can with the WEN 8-inch by 12-inch variable speed mini wood Lathe. Adjust the variable speed anywhere from 750 to 3200 rotations per minute. The WEN 8-inch by 12-inch variable speed Benchtop wood Lathe features an MT1 spindle and Tailstock taper to tightly grip workpieces, two tool rests (4-1/2 inch and 7 inch) to provide needed support for chisels and tools during operation, and a 3.2-Amp motor to keep things turning. The easy-to-use Lever clamping system makes adjustments to both the tool rest and the Tailstock simple and precise. The WEN wood Lathe also includes a flat wrench, a headstock spur center, A Tailstock cup center, A knockout rod and a 2.3-Inch faceplate for non-spindle work pieces. And, because its a WEN product, your Lathe comes backed by a two-year warranty, a nationwide network of skilled service technicians and a friendly customer help line. Remember when you could turn pens, chess pieces and more? Remember WEN.

• Perfect for pens, bowls, cups, chess pieces, and other small workpieces
• Fits workpieces up to 12 inches long and 8 inches wide
• 3.2-Amp motor provides over 50% more power than most 8-inch wood lathes
• Adjust the soft start variable speed motor anywhere from 750 to 3200 RPM
• Features a 2.3-Inch face plate, an MT1 spindle and tailstock taper, and two interchangeable tool rests

User questions & answers

Question:	Anybody know the thread size for the three tapped mounting holes on the underside of the lathe
Answer:	From their website: Benchtop mounting bolts: 0.30 Inch x 20 TPI (M8 x 1.25 pitch)
Question:	can you use a dedicated pen drilling chuck on this on this model 3420 or will it burn up the motor. I want to drill my blanks with it to
Answer:	I use a drilling chuck for all my pen blanks. As suggested, drill slowly, and frequently pull out the drill to remove shavings, as the blank may overheat and split.
Question:	How long did it take for you to get it? Says it ships in 2 months, with Prime
Answer:	When bought this lathe, they sent me 2. That being said, I got it when they said I would get it.
Question:	I'm interested in buy this lathe, does it run with 220 v or 150v, here were I'm living we run only 220. Waiting for answer, regards
Answer:	110

Product features

WEN 3421 3.2-Amp 8" by 12" Variable Speed Mini Benchtop Wood Lathe

You will now easily be able to fit work pieces up to 12 inches long and 8 inches wide with the WEN 3421 3.2-Amp 8" by 12" Variable Speed Mini Benchtop Wood Lathe. The minimal design is ideal for pens, bowls, cups, chess pieces, and other small work pieces. You will be able to take on larger projects around your home with this tool.

Straightforward, Sturdy and Easy to Operate

With a stunning build quality, the WEN 3421 3.2-Amp 8" by 12" Variable Speed Mini Benchtop Wood Lathe provides sturdy frame for various work pieces. Made from cast iron, features a 2.3 inch face plate, an MT1 spindle and tailstock taper and two interchangeable tool rests for added versatility.

Product description

Parameter:

1.Input voltage:12VDC

2.Input current:2A

3.Power:24W

4.Motor speed:20000rev/min

5.Processing materials length: 135mm.

6.Processing materials maximum diameter: 45mm.

7.The transformer has over-current, over voltage, over temperature protection.



Package Included:

1 x Set Miniature Metal Multifunction Machine

• Application:Wood, plastic, soft metals (aluminum, copper, etc.). Softwood, hardwood
• You can use the three-jaw chuck or collet (1 ~ 6mm) clamping the workpiece, center gongs high 25mm, center distance of 135mm.
• Motor speed:20000rev/min
• The transformer has over-current, over voltage, over temperature protection.
• 1 YEAR WARRANTY: If you have any issues with this product, please feel free to contact us

User questions & answers

Question:	Where do we purchase replacement cutting bits, blades, etc or does this thing use same as full size tools
Answer:	Don’t waste your money. The picture they use is meant to deceive people into thinking it is the whole thing. They will only send you the drill head NOT the lathe.
Question:	Does the chuck have a pass through hole 10mm or larger for longer rods to be used in the lathe? I need to be able to size down 230mm length rods
Answer:	Hello,Thank you for you interest. It's 110-120Volt. If you have any other questions, feel free to send us a message.Thank you.
Question:	What size cutters does this use
Answer:	I've been able to hold .005 with not really trying if I got serious I could hold .001 get good endmills though
Question:	Does this unit run on 12v or is it 120v
Answer:	No it is just the head. The lathe is not included and would be required to mount the head.

Product description

Application:

Youth Activity Center, School General Technical Room, Science and Technology Activity Room Equipment, Science and Technology Museum Student Science and Technology Creation.

Main parts of the machine:

The main components of the main shaft box, intermediate block, connecting block, tailstock, large slider, small slider, hand wheel, support and so on are made of metal. The quality of the product is improved, more durable and more precise.

Parameter:

●Input voltage: AC100V~240V 50/60HZ

●Output voltage : DC12V 2A

●Motor rated power: 24W

● Motor speed: High speed motor 20000r/min ± 15%

● Low speed motor: 10000r/min ± 15%

● Spindle speed: high speed motor 3000r/min±15%

● Low speed motor: 1600r/min ± 15%

● Spindle jump: <0.1mm

● Large slider stroke: 45mm

●Small slider stroke: 35mm

●Center height: 25mm

●Center distance: 110mm

●Maximum processing diameter: 13mm positive claw, 45mm reverse claw

●Three-jaw chuck clamping diameter: 13mm claw, 45mm reverse claw

●Handle scale: 0.1mm/division

●Packing size: 230mm*200mm*315mm

●Weight: 2.2KG

●Connection method: M12 * 1 screw hole

●Minimum clamping size: 1.5mm * 1.5mm

●Maximum clamping size: 18mm * 18mm

●Processing ability: It can process soft metals such as copper and aluminum.



Package include：

1x A set of min lathe

• This is a mini desktop lathe which can used for turning, drilling, boring, threading and other processing.
• Made of advanced aluminum alloy, durable and non-deformable for usage.
• Processing Materials: Wood, Plastic, Aluminum, Copper and other Soft Metal
• Three-jaw chuck clamping diameter: 13mm claw, 45mm reverse claw
• Processing ability: It can process soft metals such as copper and aluminum.

User questions & answers

Question:	Is this a true CNC lathe with stepper motors installed
Answer:	It only has a stepper motor in the head. Its a manual lathe.
Question:	Can this cut copper for jewelry like rings
Answer:	Dear friend, Sure. It can cut Wood and Soft Metals. It is teaching equipment.
Question:	can the bed be extended
Answer:	Yes, Long base block available on AliExpress CHINESE!!!! web site. Search mini late parts.
Question:	Do you have a quick change tool post holder for this mini lathe
Answer:	I'd just make something

Product description

10" x 18" Lathe #70-105 was designed specifically at the request of pen turners who wanted a sturdy, dedicated machine for their craft. This scaled-down, basic mini lathe is constructed of cast iron so vibration is not a factor, unlike other lathes made of aluminum. 5 Speed ranges cover the bases for boring barrel holes, roughing out pen billets, turning to shape and finishing. Lathe includes a live center, tool rest, knock-out bar and wrenches.

• Rikon mini lathe: This Rikon mini lathe features a ½ motor that provides ample power for all turning needs. With a 10” swing and 18” between centers, this mini lathe also has a self ejecting tail stock and has easy access to speed change.
• Sturdy and Dedicated: Designed specifically at the request of pen turners who wanted a sturdy, dedicated machine for their craft. This scaled-down, basic mini lathe is made from cast iron, so vibration is not a factor, unlike other lathes made of aluminum.
• 5 speed ranger: This mini lathe has a 5 speed range that covers the bases for boring barrel holes, roughing out pen billets, turning to shape and finishing.
• Includes: This lathe includes a live center, tool rest, knock-out bar, and wrenches.

User questions & answers

Question:	Does the headstock have a morse taper and also the tailstock
Answer:	Yes they are both #2 taper
Question:	Does this lathe have a 1 inch 8tpi
Answer:	yes
Question:	Does Rikon or another manufacturer make a steady rest for this lathe
Answer:	Carter products and Ron Brown's Best (Peacetree), make steady rests suitable for. 10 inch lathes. Carter Products is about $375 and Ron Brown's Best is about $160. I believe either can be adapted to Rikon 105, 10" lathe.
Question:	can a veriabule speed drive add to this lathe
Answer:	You can buy a conversion kit from Penn State. It comes with a new motor and electronics. Note that the lowest speed is 650 vs 500 RPM which is faster that recommended if you use Cole Jaws.

Product description

1/2 HP 40" 375W Power Turning Wood Lathe 1000mm WoodShop with 6pc Wood Chisel Set



Feature:

New Industrial 40" Wood Lathe.

This wood lathe features 110V 350 watt single phase motor, with 40" of cutting feed.

It has 4 quick change speeds for roughing, cutting, fine cutting, and finishing.

The bed is made out of heavy steel tubing, and the rest of the tool is made with heavy cast iron.



Specifications:

Construction - Headstock, tailstock, foot, tool rest base and tool rest of heavy cast iron. Bed is of heavy steel tubing.

Headstock . The outboard end of the drive spindle can also be used for large turning and is threaded ¾.16 left hand. The pulley system and motor are mounted to the headstock.

Tailstock - Slides along the full length of bed and clamps positively at any distance from drive spindle. The ram has a hand wheel advance of 2 3/8 inches with positive lock and is fitted with a Morse taper

120 Volt 60 Hz 350 Watt 1/2HP 3 to 4 Amps

Maximum Length Of Cutting Feed - 40 inch (1000 mm)

Sewing Over Bed - 14"

Height Of Cutting Tool - 7" (178 mm)

Motor Power - Single Phase 350 Watts

Spindle speed - 4 speeds

Turning Capacity - 356mm (14 inches) max diameter over bed. 1000mm (40 inches) max between centers

Pulley system - 4 speed V belt

Spindle speeds - 1100, 1600, 2300, 3400 rpm

COLOR MAY VARY BLUE OR RED

***LIMITED TIME FREE OFFER 6pc Wood Lathe Chisel Set



Note:

Returns: 30 day returns. Buyer pays for return shipping

• New Industrial 40" Wood Lathe. This wood lathe features a 110V 350 watt single phase motor, with 40" of cutting feed. It has 4 quick change speeds for roughing, cutting, fine cutting, and finishing.
• The bed is made out of heavy steel tubing, and the rest of the tool is made with heavy cast iron.
• Construction - Headstock, tailstock, foot, tool rest base and tool rest of heavy cast iron. Bed is of heavy steel tubing.
• Headstock . The outboard end of the drive spindle can also be used for large turning and is threaded ¾.16 left hand. The pulley system and motor are mounted to the headstock.
• Tailstock - Slides along the full length of bed and clamps positively at any distance from drive spindle. The ram has a hand wheel advance of 2 3/8 inches with positive lock and is fitted with a Morse taper

User questions & answers

Question:	Is this lathe big enough to make baseball bats
Answer:	Yes
Question:	What is the total length of the unit
Answer:	Total lenght is 58 inches.
Question:	Are there assembly instructions that I can find online? I did not see any in the box
Answer:	Look at pics on the ad
Question:	How can I get a replacement tail stock for this product
Answer:	So sorry we do not carry any parts for this item. However we can always order them from our supplier in China

Product description

Features

- High-precision, stability, low noise.

- Designed for the home DIY enthusiasts, small and portable, strong power.

- Large torque ball bearing motor.

- Suitable for all small square or cylindrical timbers such as Pterocarpus santalinus, dalbergia odorifera, Thuja sutchuenensis, etc.

Specifications

Power:200W

Maximum processing length:140mm

Maximum processing width:50mm

Material: aluminum alloy

Maximum processing thickness 50 mm

Product size:310*60*65mm

Work way:manual

Voltage:DC12-24V

Adapter:

Input:110V-24V AC~50/60Hz 1.3A Max

Output:12/15/16/18/19V 4.5A Max 20/24V 5A Max

Adapter size:113*53*35mm

Package Included:

1x adapter

1x machine

1x 50mm Diamond Cutting Blade

1x 50mm HSS Cutting Piece

1x polishing wheel

5x sandpaper

1x caliper

1x grinding rod

3x drill

1x cable

6x carving blade

1x diamond blade connecting joint

1x high speed steel blade connecting joint

1x drill chuck wrench

1x Allen wrench

1x beads fixed needle 1.5/2.0/ 2.5MM

1x thread fixed needle

• Specially designed for the home DIY enthusiasts and hobbies,small and portable size with strong power.
• Super large torque ball bearing motor, maximum rotating speed up to 8000RPM providing ultra strong cutting power with low noise, you can use it at home.
• Transparent organic dustproof glass cover with super convective cooling hole, the welding line is covered with a full heat shrinkable tube.
• With 7 levels of power adapter enable you to adjust the rotating speed easily to meet different cutting speed.
• High quality aluminum alloy base and pure steel structure drill chuck.

User questions & answers

Question:	Can this be used in making wood turned pens
Answer:	It comes with the pieces to be able to perform all the functions that it displays, yes, however the size is on such a small scale that you are putting way more effort into trying to use this than you are getting out of it. This wasn't good for anything that I purchased it for, and isn't adaptable to larger scale pieces. Doesn't have a lot of power at all to perform any of the 'tasks' it boasts to accommodate.
Question:	can the chuck take 1/4 inch metal rod
Answer:	Don't buy from this company. The lathe they sent was very poorly made and we had an awful time returning it. Amazon had to get involved.
Question:	Is the chuck removable and if so, what is the diameter of the drive shaft
Answer:	It came with 1 tool
Question:	How is this machine cnc? is there a data port or card slot
Answer:	No, it doesn't. Actually I returned it unopened after buying it for this very reason. They were very understanding and refunded the full amount. As the description says it works well with "Plastic and Wood" but not metal.

Product description

POOL CUE REPAIR LATHE CUE TIP SHAFT WRAP REFINISH TOOL with HOW TO MANUAL THESE LATHES ARE DESIGNED TO DO BASIC CUE REPAIRS & MAINTENANCE. IF YOU WISH TO DO BASIC REPAIRS SUCK AS CUE TIP REPLACEMENT, REFINISHING, SANDING, RE TAPERING, FERRULE REPLACEMENT, RE WRAPPING AND OTHER BASIC TASKS THEN THIS IS AN EXCELLENT, INEXPENSIVE EFFICIENT TOOL THAT WILL MAKE THE TASKS EASIER TO ACCOMPLISH AND DO AN EXCELLENT JOB. Designed for the novice or serious payer that needs to have a highly portable professional quality lathe for cue repair and maintaining your cue. IT WAS SO EASY TO USE AND SETUP This lathe sets up in seconds or can be kept fully assembled Lightweight yet very professional NEEDING A TOOL TO DO CUE TIP REPLACEMENT AT TOURNAMENTS AND LEAGUE NIGHTS WITHOUT SPENDING A SMALL FORTUNE WE DESIGNED THIS SIMPLE TO SET UP & EASY TO USE

• POOL CUE REPAIR LATHE CUE TIP SHAFT WRAP REFINISH TOOL with HOW TO MANUAL
• THESE LATHES ARE DESIGNED TO DO BASIC CUE REPAIRS & MAINTENANCE
• REFINISHING, SANDING, RE TAPERING, FERRULE REPLACEMENT, RE WRAPPING AND OTHER BASIC TASKS
• This Lathe is Worth its weight in gold if you like to work on your own pool cues.
• Now you can Master CUE and SHAFT