13 best utg rifle scopes

• 1 Inch Tube with Emerald Coating for Maximum Light Transmission, Premium Zero Lockable & Resettable Turrets with 1/4 MOA Per Click Adjustment
• Range Estimating Mil-dot Reticle for Optimal Aiming and Shooting Performance, Adjustable Objective from 3 Yards to Infinity
• Red/Green Dual Illumination for Versatile Applications, Large Field of View and Most Accommodating Eye Relief for Optimum Critical CQB Mission
• Complete with 2" Sunshade, High Quality Flip-open Lens Caps and Quick-detachable Rings
• Built on True Strength Platform, Completely Sealed and Nitrogen Filled, Shockproof, Fog proof and Rainproof

User questions & answers

Question:	what is the overall length of this scope can some answer for me please
Answer:	With the sun shade, it's 10.25" long.. I always use the sun shade, due to lighting conditions where I shoot..
Question:	What is the effective range of this scope? For
Answer:	Im really picky, and while this scope offered EVERYTHING I needed, they dont go into detail of exact reticle sizes... the reticle to me is WAY too large. At 50 yards the 'cross' area is like .5" wide at 9x. AT 50! so at 600 thats half the width of a face. TiborasaurusRex (youtube) goes over the effective range of the .223"/5.56mm regardless of scope.
Question:	Do I need a risor mount for this scope on my AR- 15 M&P model
Answer:	I put a 1" Monstrum riser rail on my S&W M&P 15 Sport 2. The biggest problem was to get the proper eye relief for the scope, I had to mount the scope all the way to the rear of the top rail. That works but it makes pulling the charge handle a pretty tight maneuver.
Question:	There have been complaints of a misaligned reticle, has anyone experienced or heard of this
Answer:	Mine is slightly off, perhaps 2-3 degrees. some have complained about that will cause elevation or windage adjustments to change too. Yes, that is correct to a point. Let's stay that worse case scenario, the turrets and reticle were canted 45 degrees off from each other. That would mean any elevation or windage would equally effect both. But for every 1 degree, that would only result in 1/45 of a change in the other. that equates to .02" for every inch of elevation/windage. So if the scope has 1/2" per click adjustment at 100 yards, One click of windage/elevation would result in (unwanted) .01" in elevation/windage movement with a reticle that was canted 1 degree off. Even at 5 degrees, that is still only .05" (1.2mm) at 100 yards. The point is if that small of an offset really matters to anyone, they should not be buying a $90 scope in the first place.

Product features

UTG CQB Bug Buster Outdoor Sunshade Scope

Here is a UTG red dot, one of the most efficient UTG's products. This red dot can switch from red to green when the light comes on. It can be fix on a Picatinny 21 mm rail. This scope is most usually used for Airsoft assault rifles.

Product description

The UTG 3-12X44 30mm compact scope. Features: - 30mm tube with best in class multi Emerald coated lenses to achieve maximum light transmission for best clarity - built on true strength platform, completely sealed and Nitrogen filled, shockproof, fogproof and rainproof - innovative EZ-TAP illumination Enhancing (IE) system with Red/green dual-color mode and 36 color multi-color mode to accommodate all weather/light conditions (U.S. Pat. 8, 437, 079; EU patent pending) - 1-Click high-tech illumination memory feature gets you right back to the color/brightness setting last used - most innovative, low profile illumination control with 2 soft and ergonomic control buttons designed for most natural, smooth and Quick-reaching hand/finger operations - special circuit and housing design for uninterrupted illumination even under heavy recoil - premium zero locking and zero resetting target turrets with most consistent and precise 1/4 MOA per click windage/elevation adjustment - side wheel adjustable turret (SWAT) for Parallax adjustment - from 10 yards to Infinity; side wheel ready for optional big wheel to achieve finer Parallax adjustment - TactEdge angled integral sunshade complete with flip-open lens caps and high quality max strength quick detach Picatinny/Weaver rings. Specifications: - magnification: 3 - 12x - tube diameter: 30mm - objective diameter: 44mm - field of view at 100 yards: 32' - 10' - eye relief: 3.4" - 3" - exit Pupil: 13.0mm - 3.9mm - click value At100 yards: 1/4" length: 264mm - weight: 23.2 oz - Parallax setting: 10 yds - Infinity - batteries: CR2032 3V

• 30-millimeter SWAT 3-12X44 IE tactical range estimating scope with mil-dot, full 36-color EZ Tap reticle
• 30-Millimeter tube built on True Strength Platform: sealed and nitrogen filled, shockproof, fog-proof, and rain-proof
• Best in class multi emerald coated lenses; integrated angled front sunshade complete with flip-open lens caps
• Special circuit and housing design for uninterrupted illumination even under heavy recoil
• Premium zero locking and zero resetting target turrets with most consistent and precise adjustment; lifetime warratny

User questions & answers

Question:	How much does this scope weigh and does it come with rings??? THanks
Answer:	Its pretty strong i used it on the underside of my truck, once you put it on something it does not come off
Question:	How long is the scope. The specs say 8.5" but one of the reviews says it is 11.1" long. Can someone please clarify
Answer:	Yes
Question:	is it a good scope for a rock river AR
Answer:	Good Question, I don't have a clue. As far as the adhesive I can only tell you that when a piece of scrap hit the floor, it stuck. It didn't come up easily, or until you hit it with adhesive remover.
Question:	Does this scope require a battery to get a cross hair? I don't want to rely on a dead battery in the field
Answer:	This can not be used on the exhaust system. It can be used on the fire wall or underside of the vehicle to shield the floor board etc. from exhaust pipe heat. But it must have a one inch or so air gap. For exhaust componants use a wrap product like lava rock.

Product features

UTG EZ-TAP Outdoor MS Rings Scope

This UTG Red dot is a 36 colors Mil-dot. Really precise it helps you to hit the things you want. It's a personal scope because of the different colors you can change as you want it to. Built on a strength platform, it won't move even if it takes shocks.

The 30mm Tube with best in class multi emerald coated lenses to achieve maximum light transmission for best clarity.

A custom scope

The color of the scope is custom-built with his 36 different colors. You can change it at any time just by hitting 1 button. The precision is still the same, but it helps when the light go darker or lighter.

Product description

UTG New Gen 1-Inch 4-16X50 True Hunter IE Scope w/TS Platform, Front AO, EZ-TAP Illumination Enhancing 36 Color Mil-Dot Reticle, F/B Emerald Coating, Zero Reset/Locking Target W/E Knobs, Incl Flip-open Covers, 3" Sniper Sunshade & Max Strength RG2W1204 Rings.

• Best Features Designed for Varmint/Predator Hunting, Completely Sealed and Nitrogen Filled, Shockproof, Fog proof and Rainproof, 1-Inch Tube
• EZ-TAP Illumination Enhancing (IE) System with Dual-Color Mode and 36-Color Multi-Color Mode to Accommodate All Weather/Light Conditions
• Premium Zero Locking and Zero Resetting Target Turrets with Most Consistent and Precise 1/4 MOA per Click Windage/Elevation Adjustment
• Emerald Coated Lenses for Maximum Light Transmission, Mil-dot Range Estimating Reticle for Most Optimal Aiming and Shooting Performance
• Parallax Adjustable from 5 Yds o Infinity, Complete with Picatinny/Weaver Rings, 3" Sunshade and Flip-open Lens Caps

User questions & answers

Question:	Is this scope designed for a high powered air rifle
Answer:	These rings screw together like any other scope rings , you put what ever rings you need , dove tail , weaver or picatenny
Question:	I have an mp sport 2 ar15. will this be ok? i am shooting 150 to 300 yards, maybe further(skill providing
Answer:	The battery size is CR1632. Its smaller than 2032
Question:	Does it fit to savage 93 .17hmr
Answer:	No.they must be mounted to the rifle,then the scope is mounted to the mounts
Question:	Finger adjustable torrets
Answer:	This scope is made over seas.

Product features

UTG 4-16X50 1" Hunter Scope, AO, 36-color Mil-dot, w/ Rings

•Best features designed for varmint/predator hunting

• Built on true strength platform, completely sealed and nitrogen filled, shockproof, fogproof and rainproof

• Innovative EZ-TAP Illumination Enhancing (IE) System with Red/Green dual-color mode and 36 color multi-color mode to accommodate all weather/light conditions (US PAT. 8437079; EU PAT. EP2520894)

• 1-click high-tech illumination memory feature gets you right back to the color/brightness setting last used

• Premium zero locking and zero resetting target turrets with most consistent and precise 1/4 moa per click windage/elevation adjustment

• Emerald coated lenses to achieve maximum light transmission for best clarity

• Mil-dot range estimating reticle for most optimal aiming and shooting performance

• Parallax adjustable from 5 Yds close range to infinity

• Complete with rg2w1204 high quality max strength QD twist lock picatinny/weaver rings, 3" sniper sunshade and flip-open lens caps

Product description

UTG New Gen 3-9X32 TS Platform Compact CQB IE Scope w/Front AO, Zero Lockable/Resettable W/E, EZ-TAP Illumination Enhancing 36 Color Mil-dot Reticle, Emerald Coating, Long Eye Relief, Complete w/RQ2W1154 Lever Lock QD Rings, 2" Sunshade& Flip-open Covers.

• Built on True Strength Platform, Completely Sealed and Nitrogen Filled, Shockproof, Fogproof and Rainproof
• 1 Inch Tube with Emerald Coated Lens for Crystal Clear View with Maximum Light Transmission
• Innovative EZ-TAP Illumination Enhancing (IE) System with Red/Green in Dual-Color Mode and 36 Colors in Multi-Color Mode
• Premium Zero Lockable and Zero Resettable Target Turrets with Consistent and Precise 1/4 MOA Per Click Adjustment
• Range Estimating Mil-dot Reticle for Optimal Aiming and Shooting Performance

User questions & answers

Question:	I hve two air rifles that use dove tail. Is there a way to convert with different rings perhaps so I can mount this scope.? Thank you
Answer:	With lens covers on the scope is 16 3/8 inches long.
Question:	What's the battery size? My instructions or anything does not have anything information on what battery to use
Answer:	I have used this on 50 and 100 yard paper targets at shooting range. I wear corrective glasses. The vertical cross hair is fuzzy with glasses, looks normal with out glasses. I have this same scope in a 9 power and 12 power. 9 power is just flawless, 12 power has same fuzzy issue but not so bad that I can not keep my glasses on. If I did it again I would not go above the 12 power. By the way, I use the 12 power on a bolt action 22 mag rifle, Marline. At 100 yards, from a bench rest, 1-1/2 groups all day long, and that is on a windy day. I do use a riser with it. You can find them on amazon starting around $15-20, depending on your mount and the rise you want. Shooting at the 300 yard range I would suggest a 5/8 to 7/8 inch riser. Your neck will thank you. Happy shooting. Please comment if this post was helpful to you.
Question:	Do the mounts come mounted the scope already
Answer:	It comes with Weaver/Picatinny style mounts, but an inexpensive adapter can be purchased for the 11 mm dovetails allowing you to use the supplied mounts. Another option is to purchase 11 mm mounts to fit the scope.
Question:	Where was it made
Answer:	I own 9 different UTG scopes. I have had one problem with one that I mounted on a Savage axis II. The light for the reticle stopped working. Holds zero even after several hundred rounds. This 30-06 kicks a lot harder than my 12 gauge even with slugs. It is the hardest kicking 06 I’ve ever shot. I never took it off to return it as I don’t use the light. I have them mounted on my 308, several .243s, 300 blackout, and of course 5.56 with no problems.

Product features

UTG 3-9X32 1" BugBuster Scope, AO, 36-color Mil-dot, Rings

Detail Information:

• Built on True Strength Platform, Completely Sealed and Nitrogen Filled, Shockproof, Fogproof and Rainproof
• 1 Inch Tube with Emerald Coated Lens for Crystal Clear View with Maximum Light Transmission
• Innovative EZ-TAP Illumination Enhancing (IE) System with Red/Green Dual-Color Mode and 36 Color Multi-Color Mode to Accommodate All Weather/Light Conditions (U.S. Pat. 8,437,079; EU Patent Pending)
• 1-Click High-tech Illumination Memory Feature Gets You Right Back to the Color/Brightness Setting Last Used
• Premium Zero Lockable and Zero Resettable Target Turrets with Consistent and Precise 1/4 MOA Per Click Adjustment
• Range Estimating Mil-dot Reticle for Optimal Aiming and Shooting Performance
• Adjustable Objective from 3 Yards to Infinity to Achieve Parallax-free View
• Large Field of View (Wide Angle) and Most Accommodating Eye Relief for Optimum Critical CQB Mission
• Complete with 2" Sunshade, High Quality Flip-open Lens Caps and Lever Lock Quick-detachable Rings

About Us

We set un-compromised high standards for all of our business operations. Our goal is to provide a total solution for any line of products we offer. We pay close attention to industry trends with a focus on making the products available for hunting, shooting and outdoor enthusiasts like you.

In 2009, we made an important decision to start our Made-In-the-USA Manufacturing Operation. We will continue to follow our vision for U.S. made products, to be innovation-driven.

Product description

UTG TF2 3-9X40 1" TS Scope w/Tool Free 2-Step W/E Adj.& Zero Lockable Target Turret plus Zero Resettable Adj. by Allen Key, Mil-Dot Wire Reticle, Sapphire Lens Coating, Completed w/Mid Pro Picatinny Rings & Flip-open Lens Cover, Parallax Adj@100 yards.

• Built on True Strength Platform, Completely Sealed and Nitrogen Filled, Shockproof, Fogproof and Rainproof
• User-friendly TF2 Tool Free 2-Step Target Turrets for Zeroing and Zero Locking Operations; Pull Up to Dial and Push Down to Lock
• Mil-dot Range Estimating Reticle for Most Optimal Aiming and Shooting Performance; One Piece Tube Construction with Angled Integral Sunshade
• Parallax Pre-adjusted at 100 Yards
• Complete with Picatinny/Weaver Rings and Flip-open Lens Caps

User questions & answers

Question:	How heavy is this scope, packaging says ~2lbs? I am wanting a scope that is lightweight as I hunt in the mountains and need to keep my setup light
Answer:	Yes. They are excellent for break barrel airguns and are designed to handle the double recoil. These can be used all the way up to a 30.06 high powered rifle as well. AR's, 308
Question:	What does is the distance adjust for each click
Answer:	Should be fine. I have mine on a 22-250, did 625 yds last week.
Question:	Will this work well on air rifles? specifically the Gamo Silent Stalker Whisper IGT
Answer:	I don't know anything about the weapon you cited. However, since no scope rings are provided, as long as you purchase the proper rings or mount to fit the body of the scope's body and the mounting rail for your weapon the scope should work. Be sure to select tall rings or a tall one-piece mount though. Otherwise due to the large (50mm) objective lens you could end up with insufficient clearance between the scope and the barrel.. I'll also mention that it a large scope and somewhat heavy. Otherwise I've been pleased with mine so far.
Question:	The Rings that come with this, are they 11MM or 20MM
Answer:	Yep... Instructions included... Once zeroed to your likings (whatever yards you choose) then you can loose the allen screw for the turret to move free and align the marked dot to the number "0", once you tighten the screw then whatever adjustment can be done with your bare fingers by a lossening a fixation ring... This thing is bad ass for the price...

Product description

UTG scope mount for Remington 700 long action rifle, steel specifications: material: steel pieces: 1 rail type: Picatinny/Weaver no. Of rails: 1

• Solid high quality Integral steel base with matte black finish
• Precision made to fit MNT-RM700 700 long action rifles
• 6 Picatinny slots on top for convenient scope mounting
• Half cut in Mid section for shell rejection
• Locking screws included

User questions & answers

Question:	Will this fit a Rem 721 30-06. I have only two attach points (one fwd, one aft
Answer:	Can this scope mount to a piccatinny rail?
Question:	Will this work with the Picitinn Quick release mount
Answer:	Comes with the rings but don't waste your money, the scope broke the reticle after second shot on a ruger 22. Buy a better scope, this one is junk
Question:	Will this fit on my savage 111 trophy hunter
Answer:	Black
Question:	I have a Rem 700 sps 300 ultra mag. using a bussis with piatinny rail on it will they work together
Answer:	It would be a great scope for that, works well on my .22 rimfire, so an air rifle would be no problem. You will almost certainly need different scope rings.

Product description

UTG 2. 4" Sunshade for 40MM Objective UTG Scopes Features: - UTG 2. 4" Sunshade for 40MM Ob. UTG Scopes Specifications: - Compatibility: UTG scopes w/ 40mm objective lens - Length: 40mm - Height: 68mm - Material: Aluminum - Finish: Black

• Compatibility: UTG scopes w/ 40mm objective lens
• Length: 40mm
• Height: 68mm

User questions & answers

Question:	will this fit the Nikon Prostaff 40 millimeter 3x9x
Answer:	I'm positive it will fit a 30-06. Two holes on each end.
Question:	will it fit Nikon prostaff ? 4-12x
Answer:	The bolt holes did not line up on my rifle. Had to buy a different kind.
Question:	Will it fit a simmons prohunter 4-12x40 ao
Answer:	It's for a Remington 700 Long Action... Not sure if the Savage uses the same. I suggest you contact a competent gunsmith to mount your rail and scope.
Question:	would this work on my nikon m
Answer:	Hello Linda, The Remington 700 SPS comes factory barreled without sights unless special ordered. If I understand correctly you are using a form of Back Up Sight System that would be currently mounted to the Receiver where a Scope mount of this type would normally be mounted. If this is so then the answer would be "No". The 300 Ultra Mag is a "Short Action" Cartridge and the Mount you have inquired of is for a "Long Action". A Short Action version of this Mount is offered on Amazon. This Mount you are inquiring about is great for "Scope Only" with a variety of Scope Rings available from Amazon as well. When choosing your Scope Rings make sure they are of the correct Tube Diameter, i.e., 1 inch or 30mm. If a Picatinny mount Back Up Sight were to be mounted to this mount you would have to take into account the much Higher Elevation of the sight after being mounted that would severely change the adjustability of your Rear Sight to Front Sight Ratio. Depending on your existing sight system it may make sight adjustment more problematic. My personal opinion would be to go either with Scope only, or, stay with your existing sight system if you're proficient and comfortable with your existing sights. If your existing Sights are Barrel Mounted from the Factory or installed to the barrel by a gunsmith, then the Short Action version of this mount will work for Receiver Mounting providing the Rings are tall enough to allow your scope to clear the top of the sights as not to obstruct your Scope View. I hope I was helpful in some way as I did my best in covering your question as written. Best to you... and always "Safe Shooting".Most Sincerely, Michael

Product description

- Provides Amazing, True and Consistent Extended Eye Relief for Shooters to Effectively Use on Anything Where the Optics Cannot be Mounted Directly Above the Action

- Innovative EZ-TAP Illumination Enhancing (IE) System with RGB in Dual-Color Mode and 36 Colors in Multi-Color Mode to Accommodate All Weather/Light Conditions

- 1-Click High-tech Illumination Memory Feature Gets You Right Back to the Color/Brightness Setting Last Used

- Premium Zero Locking and Zero Resetting Target Turrets with Most Consistent and Precise MOA per Click Windage/Elevation Adjustment

- Emerald Coated Lenses to Achieve Maximum Light Transmission for Best Clarity

- Practical TactEdge Angled Integral Sunshade

- Complete with Twist Lock Medium Profile Picatinny/Weaver Rings and High Quality Flip-open Lens Caps

• Eye Relief: 11" - 9.5"
• 30mm 1 Piece Tube for Maximum Light Transmission
• Built on True Strength Platform, Completely Sealed and Nitrogen Filled, Shockproof, Fogproof and Rainproof
• 6 Mil-dot Tactical Range Estimating(TRE) Etched Glass Reticle for the Ultimate Performance
• Side Wheel Adjustable Turret(SWAT) for Parallax Adjustment from "True 10 Yards" Up, and Ready to Accept Optional Big Wheel to Achieve Finer Parallax Adjustment

User questions & answers

Question:	Is this rated for .308win
Answer:	I have an M&P 15 and while I could get both the utg magnifier and utg 4.2 on the rail while keeping my rear sight the eye relief is so small that my nose was touching the charge handle... So I removed the rear MBUS sight and moved the magnifier all the way to the last slot of the rail and fixed it there. Now, while I still have to crowd up to the lens because of the crappy eye relief but at least my stock isn't all the way collapsed and I'm generally more comfortable.
Question:	Does this scope come with flip open lens caps
Answer:	Used with my holosun with acss reticle. Easy work at 270 yards, will stretch it further soon. Clarity and eye box sux, but for the money one helluva deal.
Question:	wil this work o socom
Answer:	42 mm center height for most common dot sight configuration.
Question:	Will this hold up to the recoil of my 44 super Blackhawk
Answer:	Yes* *the magnifier is a good 1/8"-1/4" taller than the EoTech. You'll need to crank down the elevation setting all the way to get the EoTech reticle centered. At that point, the internal prism (I'm guessing it's a prism) is at a weird angle and your eyebox isn't very good on the magnifier. I need to really mash my cheek down onto the rifle stock to actually clearly see the reticle through the magnifier, otherwise it kind of disappears.

Product description

UTG scope mount for Remington 700 short action rifle, steel specifications: material: steel pieces: 1 rail type: Picatinny/Weaver no. Of rails: 1

• Robust steel construction
• Solid Integral base with 6 Picatinny slots on top
• Half cut in Mid section for shell rejection
• Locking screws included
• Fits Remington MNT-RM700S 700 short action rifle

User questions & answers

Question:	Other post says will fit bergara b-14 hmr, is the quality made or go with burris optics
Answer:	Sorry, I couldn't say I bought this sunshade for a UTG 3-9x40AO True Hunter Rifle Scope...
Question:	Will this fit a Remington model
Answer:	If the forward end is 40mm and not sloped it should fit. That's the best I can do.
Question:	Can this fit on the R700 200 year anniversary? It's in 30.06 and the barrel is
Answer:	No only utg I got one and found out the hard way
Question:	What size Allen is this? I purchased a rifle that has this mount, and none of my allens fit this, wanting to get this junk mount off of my rifle
Answer:	No, it has a inset thread design which will only fit UTG.

Product description

UTG 4X32 1" Crossbow Scope, Pro 5-Step RGB Reticle, QD Rings Features: - Built on Robust True Strength Platform with Smart Spherical Structure(SSS) to Achieve Most Precise and Accurate - Wind age/Elevation Adjustment and Toughest Recoil Resistance - Unique Pro 5-Step Red/Green Illuminated Reticle Designed for Crossbows and Other Applications Requiring Variable Velocity Compensation, Includes 5 Horizontal Lines Calibrated for 300fps Crossbows for Quick Aiming at 10, 20, 30, 40 and 50-yard Distances - Side Wheel Red/Green Dual Illumination Control for Versatile Uses in Different Light Conditions - Superior Quality Precision Broadband Lens Coating Offers the Brightest Image and a Generous Field of View - Premium Zero Lockable and Resettable Target Turrets for Wind age and Elevation Adjustment - Complete with Flip-open Lens Caps and Low Profile Quick Detach Ring Mounts with Patented Lever Lock Feature - Built in Tact Edge Angled Integral Sunshade - Parallax Pre-adjusted at 50 Yards - Fixed Power: Magnification of the scope is fixed Includes: - Pica tinny or Dovetail Mount Specifications: - Magnification: 4X - Tube Diameter: 1" - Objective Diameter: 32mm - Field of View @ 100 yards: 27. 2' - Eye Relief: 3. 8" - Exit Pupil: 8mm - Click Value @100 yards: 1/4" - Length: 208mm - Weight: 12. 3 oz. - Parallax Setting: 50Yds - Batteries: CR1620 3V

• Built on Robust True Strength Platform with Smart Spherical Structure(SSS) to Achieve Most Precise and Accurate - Wind age/Elevation Adjustment and Toughest Recoil Resistance
• Superior Quality Precision Broadband Lens Coating Offers the Brightest Image and a Generous Field of View
• Premium Zero Lockable and Resettable Target Turrets for Wind age and Elevation Adjustment
• Sport type: Hunting

User questions & answers

Question:	Does this fit centerpoint sniper
Answer:	it fits a standard picatinny rail
Question:	Is the reticle still usable if it is switched off or if the battery goes dead
Answer:	Scope works fine with or without battery power.
Question:	what size covers does it take
Answer:	You don't need a cover. Both ends have flip-up covers protecting the lenses.
Question:	What speed is it calibrated for
Answer:	Per the user guide, it's calibrated for 300 fps... zero at 10 yes on the top line and subsequent lines are 20, 30, 40 & 50 yds. However, every crossbow & bolt combination varies... so you're supposed to verify the exact yardage of the lines for your specific crossbow. Mine, which is rated at 300 fps, was exactly on all the way out to 50 yds.

Product description

UTG 4-Point Locking Deluxe M14/M1A Scope Mount with 15-slotted Top Rail, Top Rail Locks into the Charger Guide Dovetail, Side Plate Features Locking Point, Horizontal Bottom Guide & Adjustable Side Screw to Provide a Rock Solid Foundation, One Piece Design Machined from Aircraft-grade Aluminum Alloy

This New Gen Deluxe Scope Mount is made for M14/M1A rifles and features a one-piece design machined from aircraft-grade aluminum alloy with a black matte finish. It features a 6-inch fully Picatinny-compatible top rail with 15 slots, a lockable rear end with charger guide dovetail, side plate with locking point, horizontal bottom guide, and adjustable side screw to provide a rock solid foundation. Its accepts Weaver style rings and is see-through to allow for the use of iron sights for aiming when installed. Plus, it installs easily with no gunsmith required and comes with black rubber rail guards.

Features:

• New Gen mil-spec quality deluxe sniper mount for M14/M1A rifles
• See-through design for use with original sights; may be low profile with special cutting, high profile with tunnel, or clearance so as not to block the user's vision from the rear aperture to front post
• Over 6-inch fully Picatinny-compatible top rail with 15 slots
• Rear end locks into the charger guide dovetail
• 1-piece machined from aircraft-grade aluminum alloy with black matte finish
• Side plate features locking point, horizontal bottom guide and adjustable side screw to provide a rock solid foundation
• Accepts Weaver-style rings and allows use of iron sight
• Installs easily, no gunsmithing required
• Black rubber rail guards included

Specifications:

• Material: Aluminum
• Weight: 5.7 ounces
• Pieces: 1
• Rail Type: Picatinny/Weaver
• Rails: 1
• Dimensions: 6.1 by 1.6 by 1.8 inches (L x W x H)

About UTG and Leapers, Inc.

Leapers, Inc., headquartered in Michigan, has been in the business of supplying shooting, hunting, and outdoor gear since 1991. By setting un-compromised high standards for all of their business operations, Leapers' goal is to provide total solutions by paying close attention to industry trends and customer feedback, with a focus on making the best-in-class niche products available for hunting, shooting, and outdoor enthusiasts.

In 2009, Leapers made an important decision to start our Made-In-the-USA Manufacturing Operation. With a full commitment to serving more customers in the market with 922R compliant products, Leapers has begun making unique mounting systems under the UTG PRO brand in Michigan and will continue to be innovators in the hunting, shooting, and outdoor industries.

• New Gen mil-spec quality deluxe sniper mount for M14/M1A rifles
• Over 6-inch fully Picatinny-compatible top rail with 15 slots; accepts Weaver-style rings and allows use of iron sights
• 1-piece machined from aircraft-grade aluminum alloy with black matte finish
• Side plate features locking point, horizontal bottom guide and adjustable side screw to provide a rock solid foundation
• Installs easily, no gunsmithing required; measures 6.1 by 1.6 by 1.8 inches (L x W x H)

User questions & answers

Question:	Can you recommend a scope with this product
Answer:	Actually made of one solid piece that when I tightened screws down on both sides was pretty flush and I would definitely say a good bargain for the money fit like a dream on the one I put on my Remington 700
Question:	Will this mount work with a 303 no1 mkiii with no carging bridge
Answer:	Depends on if the rifle is a long or short action. Google it!
Question:	Will this fit my springfield m1a precision arcangle match grade rifle
Answer:	I don't think this will work, it's a short action mount and a 30.06 is a long action
Question:	Will this fit a Springfield Armory M1a/How much fitting is required
Answer:	I have a UTG on a Rem Model 700 it came with the package, It is most likely a metric. Check with UTG.

Product description

UTG 30MM 10X44 Fast AccuAiming Compact IE Scope for Hunting/CQB & Snipping Warfare, TS Platform, SWAT AO, Zero Lockable/Resettable Target W/E, EZ-TAP Illumination Enhancing 36 Colors, Mil-dot Etched Glass Reticle, Emerald Lens Coating, Include MS RG2W3154.

• 30mm Tube with Best in Class Emerald Lens Coatings to Achieve Maximum Light Transmission for Best Clarity
• Built on True Strength Platform, Completely Sealed and Nitrogen Filled, Shockproof, Fogproof and Rainproof
• Innovative EZ-TAP Illumination Enhancing (IE) System with RGB in Dual-Color Mode and 36 Colors in Multi-Color Mode
• Premium Zero Lockable and Zero Resettable Target Turrets with Most Consistent and Precise 1/4 MOA per Click Adjustment at 100 Yards
• Built-in Integral Sunshade; Complete with UTG RG2W3154 Max Strength Picatinny/Weaver Rings and High Quality Flip-open Lens Caps

Product description

UTG 30MM AccuShot 4-16X44 IE Scope w/ TS Platform, SWAT AO, Zero Lockable/Resettable Target W/E, EZ-TAP Illumination Enhancing 36 Colors, Mil-dot, Multi Emerald Lens Coating, Completed w/ RG2W3154. Complete with UTG Max Strength Twist Lock Picatinny/Weaver Rings and High Quality Flip-open Lens Caps

• 30mm Tube with Best in Class Emerald Lens Coatings to Achieve Maximum Light Transmission for Best Clarity, Built on True Strength Platform, Completely Sealed and Nitrogen Filled, Shockproof, Fogproof and Rainproof
• 4X to 16X Power with Quick Power Selector Ring Perfect for Target Acquisition and Zooming In, 1-Click Technology for Quick Access to Your Favorite Color and Brightness in Reticle
• Field of View @ 100 yards: 24.4 feet - 6.8 feet. Innovative EZ-TAP Illumination Enhancing (IE) System with Red/Green in Dual-Color Mode and 36 Colors in Multi-Color Mode to Accommodate All Weather/Light Conditions
• Premium Zero Lockable and Zero Resettable Target Turrets with Most Consistent and Precise 1/4 MOA per Click Adjustment, Side Wheel Adjustable Turret (SWAT) for Parallax Adjustment - From 10 Yards to Infinity
• Mil-dot Range Estimating Reticle with Built-in Integral Sunshade for Most Optimal Aiming and Shooting Performance, Complete with UTG Max Strength Twist Lock Picatinny/Weaver Rings and High Quality Flip-open Lens Caps

User questions & answers

Question:	how long is this scope
Answer:	Well, I took it off and weighed it and it's 1.5 lbs. with rings and yes it does come with great rings with fast turn wing nut type clamps. Its a great scope. clear and great magnification. Pop open lens caps included. 36 color lighted reticle. Only complaint I can have is the reticle cross hairs are a little too fat for long range acquisition of small POI. Hope this helps.
Question:	reticle small? want to use this on a 17hmr at 300 yards
Answer:	The COMPACT model is just over 11" long "naked" and 11.5" with the free included scope caps. The regular model is several inches longer.
Question:	Does it fit a hammerli 850 cal 22 pellets, it has a picatinny (11 mm
Answer:	I think it should be no problem the scope is solid. Both of my shooting buddy's got it for their AR's one of them on a Rock River the other one on a Bravo company and we have been going the whole summer every weekend and up to now no problems at all. We shoot 50 yards and 100 yards with good tight groups. I think for the prize it's a decent scope if you are worried about the recoil I think it should be able to handle it. I will be putting it on my 12 gauge for deer hunting so the recoil can't be worst than that on your ar10. Good luck I hope this helps you
Question:	Can this scope handle the recoil of a shotgun or large caliber rifle
Answer:	The cross hairs show up as a normal scope the battery is only used if you want to illuminate the reticles. I use mine without the battery unless I'm going night hunting to help see the cross hair

Product features

Complete Solutions

UTG ACCUSHOT scopes are equipped with premium lockable and resettable turrets, manipulating the scope for fast and intuitive zero adjustment and retention takes only seconds and its 30mm main tube provides generous room for a large range of windage and elevation adjustment. Facing both environmental and lighting conditions is accomplished through UTG’s patented EZ-TAP 36-Color Illumination Enhancing System with 1-click illumination memory, providing a plethora of different reticle illumination colors and brightness intensities in addition to the industry’s usual standard of red or green. As a bonus, this scope also includes an integral angled sunshade, flip-open lens caps, and Max Strength quick detachable rings right out of the box.

A True Strength Platform Optic

Maximize your performance at various distances with the versatility of a 4-16X magnification range in tandem with an unprecedented side wheel adjustable parallax from 10 yards to infinity. With a 100% nitrogen filled and completely sealed main tube equipped with multi-coated lenses, a tailorable eyepiece diopter, and shockproof, fogproof, and rainproof performance, users can expect exceptional clarity and performance from a UTG True Strength Platform Optic.