13 best jon boat trailers

Product description

The Ironton Personal Watercraft and Boat Trailer Kit allows you to easily load, transport and unload your jet ski/personal watercraft. Rugged steel frame features 800-lb. GVWR, 610-lb. load capacity. Road ready and meets DOT requirements. Assembly required. Fenders: Yes, Assembly Required: Yes, Ramps Included: No, Bed Tilt: No, Lights: Yes, Side Rails Included: No, Frame Material: Steel, Wheel Size (in.): 4.80 - 12, Coupler Size (in.): 1 7/8, Load Capacity (lbs.): 610, Jack Type: No, Overall Dimensions L x W x H (in.): 126 3/4 x 52 1/2 x 16 1/4, Brakes: No, Deck Material: Steel, Rear Gate: No, Deck Size L x W (ft.): 77 1/4in. x 40 1/4in., Gross Vehicle Weight Rated (lbs.): 800

• Rolls on 12in. tires
• Roomy bed size is 77 1/4in.L x 40 1/4in.W
• Overall size is 126 3/4in.L x 52 1/2in.W
• White powder-coat finish adds durability
• Includes lights, protective fenders and 1 7/8in. coupler

User questions & answers

Question:	Can you haul 2 kayaks on this trailer
Answer:	On this Ironton Personal Watercraft and Boat Trailer Kit the angle of the bunk boards are adjustable. There are 2 bolts to fix each bunk to the bunk support. You can loosen the bolt and put the bunks flat or the desired angle, then fasten the bolt.
Question:	I have a 17 foot aluminum boat will it work
Answer:	I have converted the trailer to carry my 17 foot canoe by replacing the tongue with a longer one. The canoe hangs over the rear 3 feet which works with a canoe, but perhaps not with a boat. Also, the canoe only weighs 75 pounds.
Question:	I have a double sit kayak 13.5 ft. Does it fit
Answer:	It will fit, but it will definitely hang out over the back by 3 or 4 feet. I suppose that is no big deal, but you should be aware of that. I used mine for a 16 ft canoe, but it hung off the back by about 6 ft, even after moving the front stop bar as far forward as possible. So I bought a 10 ft piece of steel tube and used it instead of the 5 or 6 ft tongue that comes with it. That allowed me to adjust it so my 16 ft canoe did not hang 6 foot over the back. Also, notice the two carpet covered boards? They are flat and straight, so they don't fit the curvature of the hull very well . . . just contacting at arc point of the hull . . . again, no big deal, but when it sits in the hot sun all day, the weight of the canoe pushes the floor of the hull up to conform to the flat boards. I may make some modifications for that. Also note there is no front roller for the bow to rest on. I had to buy a roller and make a bracket to support the front of the canoe. I also put a rubber V stopper on the front vertical stop bar. Finally, I added two brackets to the back to hold a strap . . . painted the whole thing black with silver wheels and put two BMW logo's on the wheel bearings just for fun. Otherwise, very happy with the trailer. Good Luck!
Question:	Would this work for a 12 ft Jon boat, 130 lbs ? Thx
Answer:	We have a 10.2' and I belive it should work for a 12' no problem.

Product features

Features + Benefits

• Rolls on 12in. tires
• Roomy bed size is 77 1/4in.L x 40 1/4in.W
• Overall size is 126 3/4in.L x 52 1/2in.W
• White powder-coat finish adds durability
• Includes lights, protective fenders and 1 7/8in. coupler
• Certificate of origin will be mailed separately. Please allow time for processing

Product description

The Pelicans intruder 12 is a very stable “Jon” style fishing boat. Its maintenance free grooved and riveted deck offers great impact resistance and can contain up to 36 cubic feet of cargo. It features bench seats, 4 vertical rod holders, built-in motor mounts, Oarlock receptacles and carrying handles. Capacity 420 lb. - 190 comfortable seating for 2 persons maximum 6 HP made of RAM-X, a multi-layer polyethylene with an advanced resin providing significantly more rigidity than standard polyethylene, it is lighter, stiffer and stronger. So take your intruder 12 is built to last for many adventures. So create fishing stories worth sharing with everyone. 2-Year limited Pelicans international works hard to ensure our products are free from defect. Therefore, we will repair or replace the hull on this item should it fail within 2 years of its purchase date due to poor quality in materials or workmanship. All accessories that come pre-assembled on your product are for 1 year.

• Four vertical rod holders Perfect place to store and position fishing rods. Can be used for trolling or multi-rod fishing.
• Bench seats built-in motor mount
• Shallow draft design; flat hull for maximize stability
• Multiple storage compartments to store all your fishing gear for your trip on the water
• Carrying handles to easily carry your boat to the water - oar lock receptacle

User questions & answers

Question:	What is a motor that we can use with this boat? Can you put a link to the motor. Also what shade covers can we put on this boat
Answer:	You would require a Liquid Ball Lock Disconnect and a jumper line to attach that to your faucet shank.
Question:	can be used for beach/ocean
Answer:	Update, went to the brewery and checked, 1/2" OR 5/8", the 5/8 is a tight fit though and tough to remove for cleaning
Question:	Does this boat come pre wired for a trolling motor and/or depth finder
Answer:	Our keg coupler adapter kit have not the check valve. It only have the poppet valve. You don't need remove the poppet valve
Question:	what is the total weight capacity, passengers and equipment. Is it 420. Some guy says 850. Your ad says 190 comfortable seating, whatever that means
Answer:	The one with the line around the base is the gas post.

Product features

ExoCrate Fishing Crate Bag

The ExoCrate can also be used without a crate thanks to the panels included with each bag. Made to accommodate any standard milkcrate 13" x 13", the ExoCrate includes two fishing rod holders with drainage holes, lined storage compartment with heavy duty zipper, multiple compartments for your tools, loops to help secure the fishing bag to the kayak, reflective logos, and removable adjustable padded shoulder strap.

3 lb Folding Anchor Kit

The Pelican Folding Anchor Kit 3 LB is the perfect accessory for those who want to moor, fish or swim. This folding anchor is galvanized, features 20 feet (6 meters) of line and comes in a durable nylon bag. Please note that this anchor should not be used in strong currents.

ExoDry 20 L Medium Drybag

Bring along your gear in confidence with one of Pelican's ExoDry Dry Bags. The 20 L ExoDry provides extra room so you can bring along extra gear. This medium drybag comes with two convenient shoulder straps, allowing you to comfortably carry your bag while leaving your hands free.

Build memories that will last a lifetime!

Pelican Fishing Boats are fun for the whole family, for cottages, for rentals and camps. They are stable, comfortable, easy to use, and reliable products. For many years, Pelican has been proudly fabricating these unique watercraft known to be the best companion of fishermen!

Product description

Carpeted bunkboards provide proper center loading even in wind or side current conditions. 2'' x 4'' X 24" boards tilt to hug the hull and are covered with high grade marine carpet. Height of 21'' with adjustment out to 13" from frame on each side. Can be mounted on top of frame for extra height. Complete with mounting hardware to fit frames up to 3'' wide x 4-1/4'' high.

• precision metal stampings, fabrications and assemblies
• 2'' x 4'' x 24" boards tilt to hug the hull and are covered with high grade marine carpet; boards are untreated Southern yellow pine
• Height of 21'' with adjustment out to 13" from frame on each side
• Can be mounted on top of frame for extra height

User questions & answers

Question:	What color is the carpet black or charcoal
Answer:	Black
Question:	Is this the pair or one side of the guide
Answer:	Two guides... one for each side of the trailer... come in the oackage
Question:	Is the $72 price for one or two sides of the 2’ bunks
Answer:	both sides
Question:	What is better for boat loading? Carpeted 2' bunks or roller guides
Answer:	If you have a Pontoon style boat - carpet with 2 bunk boards on both side... and make sure they are tall enough to be seen when loading the boat out of the water. If you have a V-haul, no matter what size, rollers with bunk boards make life easier!

Product features

Guide-ON BUNKBOARD 2'

• 1-1/2" square pre-galvanized uprights, angled out at 75°
• 2'' x 4'' x 24" boards tilt to hug the hull and are covered with high grade marine carpet boards are untreated Southern yellow pine
• Height of 21'' with adjustment out to 13" from frame on each side
• Can be mounted on top of frame for extra height
• Complete with mounting hardware to fit frames up to 3'' wide x 4-1/4'' high

About Us

C. E. Smith Company, Inc. was established as a manufacturing firm producing precision metal stampings, fabrications and assemblies for a broad variety of industries. We are committed to providing precision stampings, innovative products. The entire team in our 85,000 sq. ft. manufacturing facility and our 60,000 sq. ft. distribution center is dedicated to providing the high quality products.

Stainless steel boating and fishing products includes an adjustable, completely stainless steel t-top, fiberglass electronic boxes, t-top storage bags navigation lights and antenna bracket. The line of stainless steel rod holders includes 2 way clamp models, adjustable clamp models, outrigger and flush mount models.

Product description

CE Smith 27850, front support bunk, Jon boat, boxed. This 24" carpeted bunk mounts crossways on the trailer tongue to support the flat bottom of a Jon boat. Adjustable from 5-1/2" up to 8" above tongue. Includes all mounting hardware for a 2" or 3" wide tongue. Sold, individually.

• Board is untreated Southern yellow pine covered with high quality, marine grade carpet
• Heavy-duty bracket is made of galvanized steel
• Sturdy & corrosion-free
• Made in the USA

User questions & answers

Question:	Does this only work for flat bottom boats or will it work with a v-hull as well
Answer:	The material is a soft permanent press cotton material. This material hold the color and pant crease fairly well. My husband wears his Haggar pants with dress shirts and nice shoes to work. I would not say these are "dressy" pants, but I consider them in the middle, perhaps dressy casual. I've tried my best to answer your question. Hope that helps. My husband finds these pants very comfortable and a great style fit for work.
Question:	How far forward do you mount the bracket to support a flat bottom jon boat
Answer:	Because the pants are BIG and TALL The 34L means LONG...in regular pants 34 is a standard length...
Question:	Do you get one or two
Answer:	Maybe the $80.00 pair is made of a more expensive fabric!
Question:	Is this price for each board and bracket? Or is it a pair
Answer:	Sorry, I have not tried. I don't wear pants with cuffs.

Product description

Smith's Multi-Sport Trailer ships to your door and is designed for easy assembly using common tools. Includes everything you need to carry a small boat, inflatable or PWC up to about 12' long. Its galvanized steel frame is built strong and has an ample 800lb. carrying capacity. Includes DOT approved lights, a pair of 5' adjustable carpeted bunk boards with dual supports, winch stand, winch, hook and strap, 4. 80x8" tires, and hitch coupler with safety chains. Rated for use at highway speeds. Winch stand can be mounted anywhere along the tongue to balance the load.  Proper load balancing is always critical for safe trailering!

• Unloaded Weight: 200lbs.
• Max Capacity: 800lbs.
• Gross Vehicle Capacity: 1000lbs.
• Overall Length: 140"
• Overall Width: 54"

User questions & answers

Question:	What is the top maximum speed for this trailer
Answer:	The Multi-Sport trailer is rated for highway speed, not exceed the posted limit.
Question:	What is max traveling speed
Answer:	I go a consistent 65 to 70 with two kayaks
Question:	Would it hold a fairly light 15 ft boat ?About 600 pounds
Answer:	You would have to see the manufacturing specs
Question:	I want to purchase a hobie angler 12, I am partially disabled and cannot put kayak on roof, will this work with a kayak
Answer:	The trailer can be used for a Kayak.

Product description

Instructions

1). These wheels have 2+1 adjustment positions for length base on the wheel arm end rotation position upper or lower. to remove the leg assembly from the bracket, simply push the stainless steel locking button and then the rotation button to release.

2). The wheels must face towards the boat tubes and be as far apart as possible (this will give you more stability when moving the boat around) and clear the boat tubes by about one inch so they don't rub against the tubes when being raised or lowered. the wheels must also clear the bottom of the boat by about one inch when placed in their lowered position.

3). Once you have determined the mounting positions for the brackets which should be straight up and down on the transom and about 6-8 inches up from the bottom of the bracket to the bottom of the boat, mark where to drill the 5/16” holes (drill bit not included). This is best done by separating the leg assembly from the bracket. double check everything again before drilling any holes! holes and transom must be vertical.

4. Use the supplied washers and lock nuts on the bolts on the inside of the transom to secure the brackets to the transom and then cap them with the supplied acorn nuts to protect your boat when rolled up.

www.seamaxcanada.com 1877-907-7766

• Seamax Easy Load Boat Launching Wheels Set is designed by Seamax Canada, made by hardest marine grade T6 aluminum alloy with CNC processing; Shiny looking anodized coating on all aluminum parts, product is good for saltwater using; Small parts are all made by solid stainless steel. Lab 1000Lbs tested, support MAX 500Lbs loading in all condition, good for inflatable boats, aluminum boats and fiberglass boats.
• This system is designed for boats with transom, the length of the boat should not exceed16 FT & total weight within 500 Lbs. These transom wheels should only be installed by an adult with some experience in working with tools. To install the wheel set properly, you will need to drill 4 holes (5/16”) in the transom for the mounting. Addition reinforcement may be required on some aluminum transom. And you can use marine sealant and suggested Sikaflex 291.
• Benefit from its new Push Button design & max 3 stages wheel arm, the system can be adjusted while afloat in the boat leaving or coming into, it can also bring different performance position for boat launching. The wheel arm length increment is 2.5” per stage, plus the wheel’s diameter, the range of length is 22-28 inches.
• Tire inflation: Dolly tires may not be fully inflated when shipping; please only give 15-20 PSI pressure at room temperature before using. Best to use portable type digital air pump in case tire over inflated. Tire over inflated will cause damage and the warranty is not covered. Dual wheel kit is available for this dolly for heavy loading application.
• Maintenance: Wash it after using from salt water or sandy beach. Check tire pressure before every using. Don’t store the wheels under the sun or beside the heat to maximize its life time. Take the wheel arm off from the transom bracket when store your boat. Lube the spring load dolly system is necessary. Keep the lock pin on the dolly bracket. Manufacturer 2 years Parts Limited Warranty within USA & Canada. 30 days free replacement on any defective ransom wheel sets.

User questions & answers

Question:	I have a pelican predator 103. i've noticed the transom is not as wide as the inflatable boats. i'm wondering if these would work for my boat
Answer:	My suggestion, a floor - although a good option - has two drawbacks. Make it a little harder to deploy and pack, and there is no protection if the dog scratches the side. What I use are these rubber dog boots. Your dog can use any unprotected rubber raft, protects their feet, rubber so it not slippery even on wood or tile, etc. Two notes: 1) do NOT get a perfect size, get one size larger. They need to be a little floppy because it is more comfortable for the dog and it is easier to put on and take off if you are a single person. If you are goign to use them for a bit of snow protection then you want them snug because lateral movement on the ground may make them come off. In either case it is easier to put them on using two people especially if the dog has long hair, one holding a wide hole, the other navigating the paw. Clearly worth it and far more versatile and helps non slip even on surfboards. http://www.amazon.com/Pawz-Water-Proof-Boot-Small-2-Inch/dp/B001J22876/ref=sr_1_sc_1?ie=UTF8&qid=1435465163&sr=8-1-spell&keywords=dog+fubber+boots
Question:	Can the wheels be removed for storage, and do they interfere with motor movements
Answer:	Hi; I have a 55-60 lb. dog and getting her in is no problem. What I find helpful tho is putting a tarp or cutting an air mattress the length of the boat. The added protection helps keep toenail pokes and scratches from getting to the raft itself.
Question:	Will this fit a sea eagle foldcat
Answer:	Let me tell you something, the Seahawk 2 was the best thing that has ever happened to me. They pointed and laughed and said it would never make it down the green river. I showed them. At the end of it all I sang the star spangled banner with all of the patriotism I have. Just buy it dude.
Question:	can you add the extra wheels to these like you can on the delux modle
Answer:	must be coriolis Force. try boating on equator.

Product description

PVC Post Guide-On. Adjusts Out to 13" each Side Fits Frames up to 3"W x 4-1/4"H 1-1/2" sq. 16 ga Pre-Galvanized Steel post Extends 18" Into 2" PVC tube for strength

• Mounting Hardware included; Sold in Pairs
• Adjusts out to 13" each Side
• Fits Frames up to 3" W x 4-1/4" H 1-1/2" square, 16 gauge pre-galvanized steel uprights 18" high
• For larger trailer frames check out our Large Frame U-Bolt Kit (11416): Fits trailer frames up to 3 inch wide x 5-1/4 inch tall
• 2" schedule 40 white PVC posts (2-3/8" actual OD)

User questions & answers

Question:	How wide do they adjust out to the side
Answer:	I just measured it. The bar will extend out to 17 inches.
Question:	are these strong enough to guide 18 foot bass boat in strong cross current
Answer:	I have an 18 foot deck boat. They have been quite helpful in cross winds and cross currents. I used to have to stand hip-deep in water as I pushed sideways to get us lined up on the bunks while my wife cranked the winch. Now I just pull it right in.
Question:	My trailer is wider than my boat by about 8 inches. Can the post installation be reversed so the post actually go inward instead of out
Answer:	The upright posts can be adjusted in and out to about ten inches or so. ,so shou!dn't be a problem for you.
Question:	how long is the horizontal leg that goes under the boat and connects to the trailer
Answer:	My boat is stored, so not handy right now. I have a Bennington 22' Pontoon boat and it was sufficient in length. Please note the horizontal portion of the leg is adjustable, not shown on the pic. It didn't even come close to maxing out on my boat. If putting on a Pontoon boat get the highest plastic tube avaiailable. Once the boat comes off the trailer, you can still see these when approaching, but once over the trailer they are below the sight line. Good luck.

• Made of 300 Denier PU coated Marine Grade waterproof, tear resistant, U.V resistant Polyester, reinforcement panels under Bow, windshield, Stern and other strength stress points, all weather protection, Easy clean.
• Heavy duty elastic cord sewn in around hemline for secure and snug fit. The cover is perfect for boat storage, mooring and trailering.
• Integrated buckle and adjustable strap tightening system provides easy installation and quick release.
• Extra roomy cut, double stitch at all seams for longer-lasting use, large storage bag, Tie-down straps.
• At iCOVER, we provide 12 Months Warranty for any quality-related issue.100% Satisfaction or your money back! No questions asked!

User questions & answers

Question:	Will this cover fit a Jon boat that has a steering console
Answer:	I really like the flexible waist. It doesn't expand a whole lot but it's enough to make a good difference when your weight flexes often.
Question:	My boat is 16 foot 7 inches long and 70 inches wide. Do i go with a 16 or and 18 model
Answer:	Not sure how to order rise. Mine were high, when I really preferred low. Nice looking slacks, but feels like straddling a saw horse.
Question:	Anyone try this on a 10' pond boat with 1 fold-down seat
Answer:	These have a different fabric feel to them. The cool 18s are very polyester but these have more of a wool blend feel and look to them instead of that shiny, polyester plastic look..there a bit nicer
Question:	Looking for warranty information for this boat cover? I have had it for less than a year and it has completely fallen apart
Answer:	24 to 24 1/2 inches

Product description

40" L.E.D. Post Boat Guide-OnPost Guide-Ons allow you to see the location of your trailer when it's underwater. Equipped with long lasting, waterproof and shockproof, one piece red and amber LED lamps. The LED lamps make it easy to see your trailer's position when backing down the ramp and dramatically increase your trailer's visibility over the road at night. Amber light faces front, red faces rear. For trailer frames up to 3"W x 4 1/4"H. Mounting hardware and wiring included.

• precision metal stampings, fabrications and assemblies
• Adjusts out to 13" each Side
• Fits Frames up to 3" W x 4-1/4" H
• 1-1/2" square, 16 gauge pre-galvanized steel uprights 18" high

• Enables one Person to easily move a small aluminum boat or canoe
• Rubber-coated 8-inch wide transom bar with a 9.25-inch outside support bar for securing
• Adjustable to fit transoms up to 2.75 inches thick
• Clockwide adjustment knob pulls the transom bar against the support bar for better fit
• Heavy-duty steel construction with a smooth-rolling double-wheel dolly

User questions & answers

Question:	What is the width of the clamping area
Answer:	Adjust support in front were most stable check by rocking your boat side too side on trailer Front support position on depends on jonbiat Make Length and width if you have a jon boat 42 or 48 floor width replace 2ft support with 3ft bunk I found support my G3 jon boat 14x42 perfect
Question:	Did these rust for anyone else... not made for saltwater.... is that right
Answer:	one
Question:	how does this attach to a Intex mariner
Answer:	The pair
Question:	I have a Coleman Scanoe. Any issues
Answer:	About 2 inches

Product features

Elevate Outdoor Canoe or Boat Dolly Cart

The Elevate Outdoor Canoe & Boat Dolly Cart makes moving your water vessel easier. The cart features dual plastic wheels and a steel tube construction for stability. Rest the transom of your boat on the cart, secure tight with the adjusting knobs, and you're ready for transport. The transom clamp adjusts from 0.5" to 1.5", perfect for use on smaller fishing boats and canoes.

Compact profile

Easy one-person operation

Knobs slide to adjust fit to vessel

Boat Dollies and More

Elevate Outdoor provides affordable automotive accessories for hauling, loading and transporting commercial or recreational cargo. In addition to boat dollies, Elevate Outdoor offers bike carriers and rack, cargo control bars, truck racks and truck bed extenders, and more.

Product description

Extreme Max Single-Post Horizontal Bunk Guide-Ons do more than help you get your boat on your trailer; they help prevent a multitude of loading problems. They'll help you load faster and safer, keep you from loading too deep, keep your trailer position true and are especially helpful at night. They will fit bunk or roller-style trailers up to 3" wide x 4. 25" tall*. 18" carpet-padded horizontal bunks sit on 96° angled vertical arms. These guide-ons can be adjusted horizontally up to 19" (3" trailer frame) or 21" (2" trailer frame). Vertically adjustable from 19" to 25". Extreme Max Guide-Ons are zinc-coated and intended for freshwater use only. Use in saltwater or brackish water will corrode and deteriorate the finish. 7" bolt kit available for trailer frames up to 5. 25" tall (Extreme Max 3005. 4050)8" bolt kit available for trailer frames up to 6. 25" tall (Extreme Max 3005. 4053).

• Includes a pair of carpet-padded boat trailer guide-ons perfect for 14' to 16' boats; Fits bunk or roller-style trailer frames up to 3" wide x 4. 25" tall
• 18" carpet padded bunks are vertically adjustable from 19" to 25" and sit on 96° angled vertical arms with up to 19" (3" trailer frame) or 21" (2" trailer frame) of total horizontal adjustment
• Zinc-coated for freshwater corrosion-resistance, not intended for use in saltwater or brackish water
• The size and shape of trailer frames can vary drastically, please measure your boat on the trailer before ordering to ensure a proper fit
• Hardware to fit taller trailer frames (5. 25" and 6. 25") is available, see long description

User questions & answers

Question:	Are these actually Galvanized
Answer:	I would go with the 18’, based on the width primarily
Question:	I own 14 ft EZ Loader trailer would this fit
Answer:	It should work just fine. Ours is a 12 ft and it's perfect. Has held up well.
Question:	Will it fit a trailer with 1 1/2 rails
Answer:	Don’t know answer to that
Question:	Does it come with hardware to mount to trailer
Answer:	Only for flat bottoms. A v hull would have a rubber v shaped support in the place of this one.

Product features

Extreme Max Single Post Horizontal Bunk Guide-On System

The Extreme Max Single Post Horizontal Bunk Guide-On System provides a sturdy assist while getting your boat on and off its trailer, helping you load and unload faster and safer. Attached to the trailer frame, the pair of guide-ons helps center the boat on the trailer, preventing wind and currents from derailing your loading attempts, while the uprights provide a sight line at deep launches and in murky waters. The carpeted horizontal bunks provide a soft touch for your boat, while the steel construction withstands nearly anything you can throw at it.

Single Post Horizontal Bunk Guide-On System

The Extreme Max Horizontal Bunk Guide-On System provides two 18" carpeted bunks that keep your boat lined up with your trailer. The bunks feature a pressure-treated wood construction wrapped in a durable marine-grade carpeting that helps prevent scratches and other damage to your boat's hull by providing a soft, forgiving surface when bumped against. The system is adjustable both width-wise and height-wise to offer a fit that best suits your boat.

Direct-to-Frame Mounting

The guide-ons attach directly to the frame of roller and bunk style trailers with no drilling or cutting required, making them easy to move or reposition if needed. The standard hardware kit is included, allowing mounting on trailer frames up to 3" wide x 4.25" tall. Additional hardware kits are available for larger-framed trailers if required.

See hardware kit 3005.4062 for trailer frames up to 5.5" tall.

Also Available from Extreme Max:

Extreme Max 3005.2196 2' Bunk Guide-On System

Extreme Max 3005.2199 4' Bunk Guide-On System

Along with the single post option, Extreme Max is proud to offer a similar model with a dual-stanchion design that offers versatility for trailer styles and a little extra support for loading and unloading larger boats.

Product description

Long days on the water shouldn’t be followed by an ordeal when it’s time to load your boat. Trailer guide-ons do more than help you get your boat on your trailer: they prevent a multitude of loading problems. Guide-ons keep you from loading too deep, keep your trailer position true and are especially helpful at night. They'll help you load faster and safer, especially at crowded launches. Designed for marine use with corrosion-resistant construction and hardware. Adjustable, carpet-padded bunks work on both bunk or roller-style trailer frames up to 3" wide x 4.25" tall. *7" bolts are available for trailer frames up to 5.5" tall, see Extreme Max 3005.4050.

• Includes one pair of 4’ bunk-style trailer guide-ons
• Heavy-duty, corrosion-resistant construction and hardware specifically designed for marine use
• Easy, bolt-on installation fits bunk or roller-style trailer frames up to 3" wide x 4.25" tall*
• The size and shape of trailer frames can vary drastically, please measure your boat on the trailer before ordering to ensure a proper fit (see Image #2 for guide-on dimensions and measurements)
• * 7" bolt kits are available for trailer frames up to 5.5" tall, see Extreme Max 3005.4050

User questions & answers

Question:	I was just wondering how many brackets do you get 2 your picture shows 4 I was just wondering let me know don't need the 4 foot boards just brackets
Answer:	I just use it to get to the water, and lift the dinghy in. No water - no rust.
Question:	will these bolt on to a trailer that has a 5 inch tall frame
Answer:	not familar with that boat.
Question:	Can these be used on tritoon trailers if installed to guide the inside of the outside toons
Answer:	I purchased this for a 10 ft. Aluminum Boat, I'm not not sure about a scanoe? If it has a square transom, it will work ! depends on the surface,(terrain) as for hauling. mine works great...
Question:	will this work for a 1998 hertiage bunk trailer? I have 19 foot crownline that I have difficulty loading by myself
Answer:	Maybe like i said lots of material to work with.

Product features

Extreme Max 4' Bunk Guide-On System

The Extreme Max Roller Guide-On System provides a worthy assist while getting your boat on and off its trailer, helping you load and unload faster and safer. Attached to the trailer frame, the pair of bunk guide-ons help center the boat on the trailer, preventing wind and currents from derailing your loading attempts, while also providing a sight line at deep launches and in murky waters. The carpeted bunks provide a soft touch for your boat, while its steel construction withstands nearly anything you can throw at it.

Bunk Guide-On System

The Extreme Max Bunk Guide-On System offers a pair of 4' carpeted bunks to assist your boat on and off your trailer. Width adjustments and a height adjustment from 10.5" to 16" provide a custom fit to your boat. Each bunk is encased in a durable marine-grade carpet, protecting the boat's finish and providing years of safe, comfortable use.

Direct-to-Frame Mounting

The guide-ons attach directly to the frame of roller and bunk style trailers with no drilling or cutting required, making them easy to move or reposition if needed. The standard hardware kit is included, allowing mounting on trailer frames up to 3" wide x 4.25" tall. Additional hardware kits are available for larger-framed trailers if required.

See hardware kit 3005.4050 for trailer frames up to 5.5" tall.

Also Available from Extreme Max:

Extreme Max 3005.2196 2' Bunk Guide-On System

Like the style, but the 4' bunks are just too long for your trailer? Don't worry. The Extreme Max 2' Bunk Guide-On System features the same great design features with a short pair of bunks, specially designed or shorter trailers or more protected areas where currents and winds aren't as much of a hindrance while loading.

Product description

These new CE Smith post guide-on allow you to see the location of your trailer when its under water. The 2" PVC tubes make it easy to see your trailer's position when backing down the ramp. Includes 1-1/2" square, 16 gauge pre-galvanized steel uprights, 18" high and 2" schedule 40 black PVC posts (2-3/8" actual outer diameter). stands 40" above trailer frame with black post caps.

• Mounting hardware included
• Adjusts out to 13 inch each side
• Fits frames up to 3" w x 4-1/4" H
• Sold in pairs
• Made in the USA

User questions & answers

Question:	How tall are
Answer:	Can't speak for your trailer, but I can't imagine it not fitting.
Question:	where can i buy replacement black caps for the top of the tubes? one of mine must have flown off
Answer:	Yes, the bolts that clamp the post to trailer will adapt from 0 inches to 4 1/4 inches.
Question:	Do these leave scuff marks
Answer:	Yes, it comes with Hardware. Although my trailer was too big for the hardware. So I had to go purchase longer bolts. But it does come with all the clamps.
Question:	Do they fit my bayliner 245 trailer
Answer:	This is adjustable with the knobs attached to the clamp. Plenty of adjustment for a Skiff or Pram. Dave