8 best scroll saw accessories

Product description

Note: Scroll Saw NOT included. The LIFTER is an accessory for the Dewalt 788 and Delta 40-690 scroll saws. It holds the saw arm in the UP position while you change blades and/or re-position your work piece. When you raise the saw arm The LIFTER latches automatically. Then to lower the saw arm, just lift on the arm and pull back the latch with your index finger. It's quick and easy. ----- To see a video on how to install The LIFTER, please go to: https://www.youtube.com/watch?v=leP5krqqKto NOTE: ALL LIFTERS ARE SHIPPED VIA USPS Priority Mail. They usually take about 3-5 days anywhere in the US.

• NOTE: SCROLL SAW NOT INCLUDED with the LIFTER.
• Easy to install and to use - one hand operation - makes your scrolling easier and more fun.
• Made with quality components - Anodized Aluminum...Stainless Steel...Steel and a LEXAN latch (stronger & quieter)
• Designed to last the life of your Dewalt or Delta Scroll Saw
• Note: All Lifters ship via USPS Priority Mail and arrive in US locations in about 3-5 days.

User questions & answers

Question:	Has anyone installed this on the Delta 40-694? It appears it is harder to pop the pin when leaving the blade attached to the upper holder
Answer:	I've found Frye boots to be very accurate in size. Because these have the fur lining, they may seem a little more snug than other boots to begin with, but after a few uses, they fit just like my other Frye boots.
Question:	just what does the lifter do for the dewalt 788 scroll saw
Answer:	No these do not. But the toe is more rigid than the sides of the boot.
Question:	Why wouldn't someone just snug up the screw on the pivot point on the upper arm at least on the
Answer:	I don't think so. I believe they are made out of country. I got a size 9 and they were small and narrow. Had to send them back. I always wear size 9.
Question:	I take it that cutting the plastic voids the warranty on the saw, correct
Answer:	There are no boot loops. I don't know what a "boot pull" is. I use a bootjack sometimes, to pull them off. I've had no problems getting them on (getting them off isn't the easiest, but they stretch and become easier to pull on and off, over time).

Product description

Designed for use with the DW788 scroll saw, the DeWalt DW7881 scroll saw work light makes it easy to keep your work area well-lit for improved visibility, accuracy, and safety. Featuring a flexible-neck design that allows you to have complete control over positioning and a three-wire grounded plug, this light is durable and easy to mount. The work light comes with a 25-watt bulb.

From the Manufacturer

DEWALT DW7881 Scroll Saw Work Light

• Included Components: Unit, Instruction Guide

User questions & answers

Question:	Is this the newer version? Apparently there is an improvement to this item that makes it more likely to stay where it is positioned
Answer:	medium brown
Question:	What type of bulb, it said "intermediate" base?? what size is that
Answer:	Toe box on Veronica is about same size but shape is more pointy. Soles are not grippy like engineer
Question:	what are the electrical properties of the bulb
Answer:	I just received these boots within the last two weeks. I own several pair of Frye boots, shoes and sandals which have been bought at various retail stores and directly from Frye as well as Amazon. I have actually ordered 3 different Frye sandals/boots/shoes from Amazon and every time I have ordered, they have been the Frye quality I expect.
Question:	What type of bulb does the DW7881 lamp take
Answer:	On my pair of 8.5’s, they are 16.5 inches from the bottom of the boot. I hope this helps.
Question:	Hello, I'de like to buy this product. Is it possible to send it to France ( Paris ) Thanks
Answer:	15" around, but there are also 2 elastic gores, 1 on either side of the back seam.
Question:	Can this be used to mask laser cut pieces
Answer:	The calf measures 16", but l got the extended version. They were a little tight at first but after wearing for a while they fit well with skinny jeans and were quite comfortable.
Question:	Can I run this through my Inkjet printer
Answer:	i'm not sure how long of a period of time you have in mind, but i've spent a half day out in the snow with these and was dry throughout. i've used them in some rain storms too, and as long as the puddles don't go above the leather, you're left nice and dry!
Question:	Could this be used to hold layers of veneer together while cutting
Answer:	I don't know that there is a rating, but toes seem to get cold easily in most rubber boots. These are nice boots, and look great, but I wouldn't wear them in temps much below freezing for long. Also, I have many boots, but these are some of the heaviest I own. Excellent lug sole for traction in snow.

Product description

This plywood is a functional grade material composed of birch from parts of Russia. The Baltic birch is graded as a B-BB, which means that one face, B, will be a whole face, no splices, have no patches (plugs that are used to cover defects) but may contain knot pattern or mineral streaks. The other face, BB, and the inner plies will contain patches and tight and not so tight knots. Baltic birch is solidly conceded to be the best plywood for use when scroll sawing. This pack of 11-7/8" x 11-7/8" sheets includes four 1/8" thick, two 1/4" thick, two 3/8" thick, and one 1/2" thick. About Us: Founded in Boston in 1928, Woodcraft's operations were moved to Parkersburg, West Virginia in 1989. It's been over 90 years since Woodcraft first began selling high quality woodworking tools and supplies out of a one room shop in Boston's North End, and Woodcraft is still firmly committed to providing woodworkers with superior products and expert advice. We are America’s leading supplier of saws, planes, power tools, hand tools, wood stain and paint, routers, sanding, wood, kits, dust collection and more. Our award winning family of brands includes WoodRiver, Highpoint, Woodcraft and Woodcraft Magazine as well as the greatest selection of woodworking books, videos, and plans

• Contains 9 11-7/8" x 11-7/8" sheets
• Four 1/8" thick
• Two 1/4" thick
• Two 3/8" thick - One 1/2" thick
• Woodcraft is America’s leading supplier of saws, planes, power tools, hand tools, wood stain and paint, routers, sanding, wood, kits, dust collection and more. Our award winning family of brands includes WoodRiver, Highpoint, Woodcraft and Woodcraft Magazine as well as the greatest selection of woodworking books, videos, and plans.

User questions & answers

Question:	Can i get these 1/8' boards cur to 8' x 10". i want them to fit in an 8 x 10 frame
Answer:	Yes we can supply baltic birch in 8 x 10 message us for the details
Question:	How heavy is the shipping of this playwood? i need to know if i can send it to brazil and how heavy is the box. thanks
Answer:	this weighs about 8 lbs

Product description

Double parallel link arm design dramatically reduces vibration and noise, for extremely accurate cuts. Exclusive tool-free blade clamps, On-off switch, electronic variable speed, flexible dust blower and blade-tensioning lever are all located on the front upper arm. Arm design pivots from the back of the saw to the front and lifts so blade can be easily threaded through the material for inside cuts. Unique arm design keeps the blade perpendicular to the work. Oversized, cast-iron table provides excellent material support and bevels 45 degrees left and right. Specs: Motor 1.3 amp rating, 120V AC. 400-1,750 cutting strokes per minute. Table size 16" x 23-3/4". Weighs 56 lbs. Meets OSHA standards, CSA approved and U.L. Listed. Stand Not Included . Featured length of the flexible shaft is approximately 22 inches long

The dependable DEWALT 20-Inch Variable-Speed Scroll Saw is designed to help you create accurate, detailed workpieces with ease. Its user-friendly configuration with easy-to-access controls, reduced-vibration design, and variable-speed performance allow for incredible precision. For added convenience and durability, an integrated cast-iron table provides material support, and a flexible dust blower helps keep your work area pristine.

Unique Arm Design for Accurate Cuts

A scroll saw needs to perform both reliably and accurately, whether you're crafting custom jigsaw puzzles or designing unique trim pieces. This DEWALT scroll saw's double parallel-link arm design helps it deliver on both fronts by reducing vibration. The specially designed arm pivots from the back of the saw to the front, shortening the distance that the arm needs to move and allowing for smoother, quieter saw operation. With less vibration, you can produce accurate cuts with ease.

This unique arm design also works to keep the saw's blade perpendicular to whatever you're working on, reducing the chance of over cutting or under cutting.

Easy to Handle with Variable-Speed Control

Adding to the saw's intuitive, design are convenient controls engineered by DEWALT to keep your workflow smooth. The saw's on-off switch, speed control, and blade-tensioning lever are all located within easy reach on the front, upper arm. The saw's flexible dust blower is also located on this portion of the arm so it can easily be directed where you need it, keeping your work surface clear of unwanted debris.

The scroll saw's electronic variable-speed control allows you to make quick, accurate adjustments and utilize speeds ranging from 400 to 1,750 strokes per minute. The saw relies on a dependable 1.3 Amp motor for the power you need and delivers a variable stroke length between 3/4 inch and up to 2 inches deep. This application-specific performance translates to improved control and cleaner results.

Save Time with Tool-Free Blade Changes and Adjustable Table

Whether you're working with a variety of specialty materials or you're simply ready for a more aggressive cut, the DEWALT exclusive, tool-free blade clamps allow you to complete blade changes in just seconds. And the arm is easy to lift, making it easy to thread the blade through materials when making inside cuts.

Weighing 56 pounds, this scroll saw has a heavy-duty feel yet is small enough to move around the shop easily. The saw's oversized, cast-iron table provides excellent support no matter what you're working on, and the table bevels 45 degrees to the left and 45 degrees to the right for added versatility.

This 20-inch variable-speed scroll saw comes with a DEWALT warranty package that includes a three-year limited warranty, a one-year free service contract, and a 90-day money-back guarantee.

What's in the Box

DEWALT 20-Inch Variable-Speed Scroll Saw, hex wrench, and blades.

• Double parallel link arm design dramatically reduces vibration and noise for extremely accurate cuts
• Exclusive tool free blade clamps allow blade changes in seconds. Depth of Cut (inches): 2 inch
• On off switch, electronic variable speed, flexible dust blower, and blade tensioning lever all located on front upper arm
• Arm design pivots from back of the saw to front, shortening the arm movement for smoother, quieter operation
• Arm lifts so blade can be easily threaded through the material for inside cuts

User questions & answers

Question:	Does this saw come with the stand
Answer:	no stand comes with the saw check out harbor freight thats where i purchased my stand and light for about $75which work very well but i did have to use a 2x12 board to mount to the stand.
Question:	How thick of a hardwood piece can this cut with ease
Answer:	The thickest that I have cut is about an inch and a quarter hardwood, had no problem, I believe you could even thicker if you took your time and not push it real hard and use sharp blades! Hope this helps !!
Question:	Has anyone used this saw for pinewood derby cars? Is it powerful enough
Answer:	I would say no. This saw is designed for small flat wood. To cut out pinewood derby cars I would suggest a nice bandsaw.
Question:	How can I tell if my 788 is made in Canada or in Asia
Answer:	Your can contact DeWalt at 1 800 433 9258DeWalt is now a popular brand of tools for commercial contractors. In 2002, DeWalt ceased all tool manufacturing in the USA and moved manufacturing to China, Mexico, Thailand, Japan and Korea. In 2004, Black and Decker bought rival power tool manufacturer Porter-Cable and combined it with DeWalt in Jackson, Tennessee.

Product features

DEWALT DW788 1.3 Amp 20-Inch Variable-Speed Scroll Saw

The DW788 20" Variable-Speed Scroll Saw operates quietly and smoothly for accuracy. The tool-free blade clamp allows for quick and easy blade changes. Convenient placement on the liftable arm of the dust blower, power switch, and saw adjustments on the front of the upper arm provide for easy adjustment. Oversized, cast-iron table provides excellent material support and has the ability to bevel to both the left and right.

Product description

This DEWALT scroll stand is a great accessory to have when you don’t have a lot of work bench space and you’re looking for a sold surface for you DEWALT DW788 scroll saw. Ruggedly crafted with holes at the base so you can bolt the stand to the floor, this stand is built to last in even heavy duty applications. It’s built from all metal can be simply orientated to the height you need with the rear adjustable legs.

From the Manufacturer

DEWALT DW7880 Scroll Saw Stand

• Sturdy, lightweight stand
• Robust all-metal construction
• Adjustable legs allows height adjustment for optimum comfort

User questions & answers

Question:	I am buying the dewalt 788 scroll saw in looking at this stand i find i cannot sit at it. can anyone recommend a stand brand that i can sit at
Answer:	Not sure why you would use a mask on the laser cutter. This is a temporary adhesive. I have used it while cutting .75-1.0 inch thick hardwood and the blade gets very hot. I had no issues removing the product due to the heat but I also control my speed to avoid burning so this is no where near your temperatures.
Question:	Will this work with wen scroll saw 24x11x
Answer:	Probably not. It’s sticky on one side to apply it to the wood, then the paper is peeled off the other side to attach the pattern. The sticky side won’t go through your printer.
Question:	I ordered through Amazon. It didn't have any bolts in the box (which was damaged upon arrival). If you ordered through Amazon did you get bolts
Answer:	not exactly sure, as long as the wood i apply it to is good n smoothe n dust free it does good holding my patterns to the wood while im scrollsaw cutting, i would say try it with a small scrap piece first and see how it does for you.
Question:	Can anyone tell me what the assembled height (floor to table) is for the scroll saw when it is mounted on this stand
Answer:	Sorry the Lifter will not work on the Delta 40-694. It only works on the Dewalt 788 and the Delta 40-690. The Delta 40-694 has a built in mechanism for holding the saw arm in the up position. Frank - Papa's Workshop
Question:	Do these fit any scroll saw
Answer:	The Dewalt scroll saw arm will not stay in the UP (raised) position by itself. This makes it difficult to move your blade to a new position for an different interior cut in your project. The LIFTER is an accessory for the scroll saw that allows you to latch the saw arm in the UP position when you need to. Then you just unlatch the LIFTER and lower the saw arm so you can continue to make cuts in your pattern. Many folks, including myself, used to prop up the saw arm with a block of wood. Now we don't have that problem anymore. Thanks Frank Carey - Papa's Workshop
Question:	Can i order just the number 5 one
Answer:	Bill, thanks for the question. What you're suggesting does work - sorta. Here's my thoughts. When you tighten the screw enough to hold up the arm, then there is added resistance when you want to lift the arm. Also when you want to lower the arm you have to also overcome the added resistance. So it does require extra effort on your part to raise and lower the saw arm. Granted if you don't set it too tight, it doesn't take a lot of muscle to raise and lower the arm. But if you're doing a lot of fretwork you'll be raising and lowering the arm a lot. So the extra effort gets kinda old after a while. I tried that method a long time ago and found I didn't care for it. If you make it too tight then the resistance is worse and if you make it too loose then the arm won't stay up. I think I was on a forum some time ago and someone said not to use that method on the Dewalt 788. Sorry but I don't remember which forum. One of the benefits of the Lifter is that it has no added resistance to the raising and lowering of the arm. The Lifter has about 95 reviews on Amazon and about 93 on my Papa's Workshop website. Almost all of them are 5 STAR reviews. If you have any questions please let me know. Thanks - Frank
Question:	do they fit the dewalt
Answer:	Tamara, I can't answer that Yes or No. In my personal opinion I don't think it would since it doesn't affect the operation of the saw in any way. However, that is just my opinion. You might contact Dewalt Tech Support and see what they say. Here's a number that I found - 1-800-4-dewalt.
Question:	What are the tpi for each number? I find they vary according to manufacturer and would like to know if possible
Answer:	I have the "Smoke" ones and they have been fine in the rain.

Product description

Facibom's trademark rights have been registered, and if any other merchants need to sell our products, please be sure to get authorization from us. Facibom will always be committed to providing customers with a quality shopping experience. size:127mm

Material:Carbon steel

colour:black

Package Contents:

48 X Pinned Scroll Saw Blades(TPI 10/15/18/24 each 12 items)

Only the above package content, other products are not included.

Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

• Tasp 48 pcs 5 INCH (125mm) fixed roller saw blades
• perfect for scroll saw works on hard and soft wood, plywood, plastic and chipboard.

Product description

This kit converts most 16" scroll saws to accept both plain end and pin end blades! Easy to Install. Designed for use on these 16" scroll saws: Sears Models 23611 & 23612; Ryobi Model SC 160; Dremel Models 1671 & 1695; Skill Model 3330-3335; Central Machinert Models S 5909, 62519, 93012; Northern Hydraulics Model SS16; AMT Models 4601 & 4602; Reliant Models DD66 & DD67; HAFCO B-18V; Einhell TH-405E; Proxxon Micromot DSH-2; Record SS-16V; Shop Fox W1713-16; Scheppach Models SD1600, 240VS; Deco 405, 88002123; Rikon Model 10-600VS; Grizzly Go563 VS-16”; Wen 3920-3921. Contains all hardware and tools for installation.

• Kit converts most 16" scroll saws to accept both plain end and pin end blades
• Easy to Install
• Contains all hardware and tools for installation
• Country of Origin: UNITED STATES

User questions & answers

Question:	does it fit a dremel model
Answer:	The base dia. is about the same size as a dime. It`s about 1/2in. long and looks like a small flood light. It gets real hot !!It does drift a little at times. I hope this helps.
Question:	I cant afford a new saw, would this work on a porter cable 18 inch saw
Answer:	I have an older version of the light so I don't know if the bulb type changed when they redesigned the shape of the lamp head, but it is a miniature incandescent bulb.
Question:	can i use with a makita scroll saw
Answer:	It uses a 25 watt mini flood lamp that puts out plenty of light and heat. Make sure not to touch the bulb guard while the light is on or right after turning it off. It can get downright hot to the touch!
Question:	does conversion kit fit a harbor freight 16 inch scroll saw
Answer:	Foreign orders are all mailed by First Class International Air Mail when placed through our Website. Delivery can be expected in 28 business days or less of processing a Foreign order. For pattern orders you may refer directly to our shipping chart online, see below. Only International orders containing supplies must be weighed to determine the Postage & Handling charges. An order for a 20 foot roll (item SST20) with shipping charges to France would be $39.95 USD. Note: E-mail is not secure, so we do not recommend sending credit card numbers by E-mail.Thank you,Robin / Customer ServiceThe Winfield Collectionthewinfieldcollection.com(810) 735-2480 EST phone(810) 735-2481 faxInternational Shipping and Handling Charges in US funds for pattern orders:Merchandise Total S&HUp to $10.00 $8.9510.01 to 20.00 $10.95 20.01 to 30.00 $13.95 30.01 to 50.00 $16.95 50.01 to 75.00 $19.95 75.01 to 100.00 $24.95 100.01 to 150.00 $29.95 150.01 & over $39.95

Product features

Upper Blade Clamp

Upper Blade Clamp mounts on the upper saw arm – allowing a saw built for pin end blades to use plain end blades.

Lower Blade Clamp

The Chrome Bracket Assembly with Lower Blade Clamp mounts on the lower saw arm to hold plain end blades.

Fixture for blade holder

The Fixture Block makes it easier to tighten and loosen a blade in the lower blade clamp. ONLY for plain end blades.

Step by step instructions

In 2020, the team at Olson Saw Company modified the kit. Many improvements later, they rewrote the instructions!

In the past, if you had a saw like this – you were limited to just a few blades.

With a greater choice of plain end scroll saw blades – more tooth styles and narrower blades available, people with scroll saws made to use pin end blades can use these ‘more advanced’ blades if they install the Olson Scroll Saw Conversion Kit. This kit converts most 16in. scroll saws to accept plain end blades. The kit can also convert saws made for plain end blades so that they can use pin end blades – although this is less common. Recently the kit was improved, the instructions were revised and we made this video to get the word out. The kit contains all hardware and hex wrenches needed for installation.

Product description

Scroll Sander sanding belts easily smooth the edges of scroll saw projects in wood, plastic, metal and composites. These fabric-backed belts have molded polycarbonate ends for attaching to most scroll saws that take 5" blades. Scroll Sander belts rapidly remove bumps, burns and feathering and correct wandering from a cutting line. They also work great on curves, concave or convex edges and can reach into intersections. Made in USA. Plain end and various sandpaper grits are available.

Special notes: Fits most 5″ scroll saws that take Pin End blades. Modifications may be required to throat insert or table opening depending upon width of sander used. Be sure to check yor

table/throat plate opening before purchasing sanders. DeWalt & Excalibur Scroll

Saws only accept the 1/4″ sanders unless you drill the table hole larger.

Dremel 1670, 1671 & 1680: use pin end sanders. Remove nub of plastic at gate to fit into clamp, if necessary. Delta: use side mount, cut table insert to fit sander, or remove table insert.

Ryobi SC 160: use pin end sanders.

Hegner: use pin end sanders.

Does not fit RBI, Reliant, or Moto-Shop.

Plain end sanders fit most conversion kits for mounting plain end blades on pin end scroll saws.

• sandpaper
• Scroll Sander sanding belts easily smooth the edges of scroll saw projects in wood, plastic, metal and composites
• These fabric-backed belts have molded polycarbonate ends for attaching to most scroll saws that take 5" blades
• They also work great on curves, concave or convex edges and can reach into intersections
• Item Package Dimension: 2.0" L x 8.5" W x 1.0" H
• For Saws that take pin-end blades
• Made in USA

User questions & answers

Question:	Will these work on a harbor freight scroll saw that uses pinned scroll saw blades
Answer:	Link below:https://www.amazon.com/gp/aw/d/B00CKF3Z9Q/ref=mp_s_a_1_4?ie=UTF8&qid=1500560467&sr=8-4&pi=AC_SX236_SY340_QL65&keywords=6+dozen+%235+scroll+reverse+flying+dutchman&dpPl=1&dpID=51AcspMvTEL&ref=plSrch
Question:	Will these work on a harbor freight scroll saw that uses pinned scroll saw blades
Answer:	Yes. They will fit. They are approx. 5" in length and pinless.
Question:	will this work on the jet scroll saw
Answer:	I don't know. I just go by recommended blade per thickness of wood. But a do love the way they cut. You need to get a fill for them but you will love them, Good Luck
Question:	Will these work with a Dewalt pinless scroll saw
Answer:	I don't know if this is a newer version. I purchased the same work light for my scroll saw and I love it. It stays positioned perfectly. A must have.

Product features

For greater accuracy

ScrollSander

belts remove bumps, burns, and feathering, and correct wandering from a cutting line.

Subtle curves

They also work great on curves, concave or convex edges.

For challenging intricate projects

They can reach into intersections and interior cuts.

Pin end for saws that take pin end blades

For best results experiment with using them a slower speeds to find what works best for you!

ScrollSander sanding belts are made in USA!

Modifications may be needed on throat insert or table opening depending upon width of sander. Check your table/ throat plate opening before purchasing sanders.

Dremel 1670, 1671 & 1680: use pin end sanders. Remove nub of plastic at gate to fit into clamp, if needed.

Delta.: use side mount, cut table insert to fit sander, or remove table insert.

Ryobi. SC 160– pin end sanders.

Ryobi. SC 162, 162VS & 165– plain end sanders only.

Hegner– pin end sanders.

Does not fit RBI., Reliant, or Moto-Shop.