14 best 2 cycle oils

Product description

Six Pack Of Echo OEM 2.6 fl oz PowerBlend® XTended Life Oil

Part # 6450001

6 2.6 oz Bottles

1 Bottle to One Gallon of Gas

• Echo 6 Pack of 1 Gallon Power Blend Oil Mix (50:1) 6450001

User questions & answers

Question:	How do I make it 25:1 ratio
Answer:	Usually the ratio is 50:1, that's a little container of two cycle oil (2.6 oz) to one gallon of gas. To make 25:1 use the 2.6 oz two cycle oil to a 1/2 gallon of gas. That's the simple way. I just got a two cycle engine that's Chinese made and this appears to be the trend so I tend to think it may be important to get the extra oil in the mix just to be safe.
Question:	Does this product contain Fuel Stabilizer
Answer:	Yes, it does contain Fuel Stabilizer. Great for off season to help jets from getting clogged and keeping fuel fresh. Highly recommended. Its what I use in all my 2 stroke motors.
Question:	Is this a synthetic oil? If not I bought it for nothing
Answer:	It states right on the bottle's label that it's a synthetic blend, which typically means it's part petroleum and part synthetic. I've been using the Echo branded 50:1 oil in my Echo weedeater (now 18 years old) and Echo leaf blower (now 20 years old), and with seasonal maintenance and proper care, both still start and run like they did when they were new.
Question:	First time user...what are the directions
Answer:	One gallon of gas to one 2.6 oz bottle of oil equals the 50 to 1 ratio.

Product description

16 oz. bottle of high quality 2-cycle engine lubricant specially formulated for higher operating temperatures of air cooled engines. Easy-mix ashless oil for up to 50:1 mix ratio.

From the Manufacturer

The genuine Briggs & Stratton 2-Cycle Easy Mix Motor Oil - 16 Oz. with fuel stabilizer that leaves no residue and prevents plug fouling and engine deposits.

• 2-cycle easy mix motor oil
• Fuel stabilizer that leaves no residue and prevents plug fouling
• Recommended for toro, lawn boy, ryan and other 2-cycle outdoor power equipment
• Oil tip and measure
• Ashless additives; 16 ounce can

User questions & answers

Question:	Is 6 oz ok for my 80cc bike I have a 1 gal tank and I need 20:1 for after breaking in and 16:1 for breaking in need a response fast I need oil
Answer:	you can make the mix what ever you want just read the mix instructions
Question:	I have never used this before. Do i need to buy anything else for my trimmer
Answer:	I assume you have a 2 cycle trimmer. Read the manual on the correct oil/gas mixture. Most American built trimmers use a 40:1 or 50:1 mixture. 40:1 is 2.6 oz. per gallon. A little less oil if 50:1. Chinese 2 cycle motors still use 25:1 or 20:1 oil mixture. Use 5.1 oz. of oil per gallon of gas for 25:1 or a little more if 20:1 mixture.
Question:	How many gallons will this treat if one whole 16 oz bottle is used
Answer:	I use 50:1. That takes 2 oz per gallon so I get 8 gallons per bottle. It is great having the squeeze section so you can precisely measure before filling gas can.
Question:	What size (oz) is the measure cup on top? Say I neeeded 3.2 oz
Answer:	It has numerous markings including 32 to 1 or 3.2 oz there is a graduated scale on the side, loosen the cap and squeeze gently until the desired amount is reached. Should you decide to go with this, I used a sharpie to highlight the markings to make then easier to read

Product description

Husqvarna Two Stroke Cycle XP+ Oil Part Number: 1XP+



Substitutes/Replacement for: 1XP+



This Part is known to be Compatible with the following vehicles:



na

• Lowers Engine Operating Temperatures
• Extends Engine Life
• Less coating on the piston and in crank case
• Includes Fuel Stabilizer
• It is a synthetic blend designed for tough, professional usage

User questions & answers

Question:	I used jones red oil in the past. it’s been a year since i have mixed gas. do i need to be concerned about compatibility
Answer:	If the gas is a year old you need to throw it out
Question:	Will this work on a 3cycle rotertiller
Answer:	Don't think there has ever been a 3 cycle motor. If you mean 2 cycle rototiller it will work fine.
Question:	Can this be used in 40:1 machines
Answer:	I run this mix at 40-1 in all 3 of my Husqvarna chainsaws two of the call for 50-1 mix. I used to run it at 32-1 as one of my saws, a 1978 husky 480 CD requires 40-1. I prefer to keep my saws around for a while and not have them seize up.
Question:	first time having to use this - may be a dumb question but I have to mix with gasoline correct
Answer:	Correct. If using this your machine is most likely a 2 stroke machine. You need to find out what ratio the manufacturer recomends for the machine you are using it in. Mix the gas and oil to the correct ratio and then add it to the machine. I recommend getting a small 1 gallon gas can specifically for your mixed solution. Gas nowadays goes bad quick, so if you are not using much, only mix around 1 gallon at a time.

Product description

STIHL 2.6-ounce high performance ultra 2-cycle engine oil is a fully synthetic 2-cycle engine oil specially suited for high performance chain saws and power tools. This oil has outstanding engine cleaning characteristics, plus ultra superior lubricating qualities in comparison to other 2-cycle engine oils. This oil is biodegradable, degrading by 80 percent in 21 days.

• Ultra lubricating qualities that are superior to other 2-cycle engine oils. This fully synthetic oil is also highly biodegradable
• Fully synthetic oil specially suited for high performance chain saws and power tools
• 2-Cycle engine oil
• Outstanding engine cleaning characteristics

User questions & answers

Question:	I realize that this works in a 50:1, but can it be used in a
Answer:	I am not in a place to "second guess" the manufacturer of your device, but I know that oil products have improved over the years. I was a hands-on mechanic with 2-stroke equipment for a lot of years and I've seen the required mix go from 20:1 to 50:1 and higher. Some of this is due to the materials used in the equipment and some of this is due to the fact that newer oils have higher film strength. I believe this Stihl product is a full synthetic oil. I don't believe that running this stuff at the 50:1 ratio will hurt anything, but I also believe that increasing the mix ratio on this stuff to 40:1 will not cause problems with your current equipment and might only show itself as an occasional fouled spark plug.
Question:	Why is the same package only $14.99 in the little hardware in town
Answer:	Yeah. I just bought mine for $1.95 each locally.
Question:	Can this product be stored in below freezing temperatures during the winter
Answer:	Absolutely! It stays in my shed all winter and I have to say that since switching my machines to this synthetic oil they have never ran better. I have been using full synthetic oil in my vehicles since around 1980. I have NEVER had any engine issues with any of my vehicles and some of them I have racked up over 200,000 miles on before I traded them away.
Question:	Why is this $5 more then in a retail store
Answer:	I just paid $1.99/ea at Ace - the expensive hardware store. And the chain oil that's $42+ here? I paid $15.99. I've been noticing a lot of stuff is cheaper at the store lately.

Product description

Pennzoil marine xlf extended life formula outboard 2-cycle synthetic blend oil was developed for engines that are "seasoned" or have been in service for a few years. The robust formulation makes marine xlf extended life formula outboard 2-cycle synthetic blend oil also very suitable for new high-displacement/horsepower carbureted or direct injection outboard motors. It contains only ash less components which helps prevent any lubricant related resignation and spark plug fouling. It's anti-gel properties help resist gel formation due to water or other contamination.

• For best performance, follow the manufacturer's recommendations in your vehicle owner’s manual.
• Xlf outboard two-cycle oil mixes easily with gasoline, and is dyed Blue to allow for easy detection. Follow engine manufacturer's recommended fuel/oil ratio for premix systems
• Maximum additive treatment, including increased detergency over the TC-W3 formulation
• Nmma TC-W3 certified
• Protect against piston-scuffing
• Keep performance-robbing carbon deposits from forming in the combustion chamber, piston tops and under crowns and piston-combustion rings

User questions & answers

Question:	Will this oil be good for a 1970-1974 ted Williams sears 7.5 outboard engine
Answer:	Yes
Question:	is this oil ok for stihl back pak blowers
Answer:	If you unit is a 2 stroke engine it will be fine.
Question:	I have a 1984 90 hp yamaha. never used anything but yamalube. will the pennzoil work for me
Answer:	Yes...to be honest they all work as long as it say marine in its the right mix you need for your boat...If you get stuck in a sticky situation you can use regular two-stroke to get you back home safe
Question:	Would this work on a Kawasaki 550sx stand up jet ski at a 40:1 ratio
Answer:	Yes, it's a good 2 stroke oil when mixed in the proper ratio. I use it in my outboard and chainsaw.

Product features

Pennzoil Marine XLF Engine Oil

Description:

Developed for marine engines that are “seasoned” or have been in service for a few years, the robust formulation makes Pennzoil Marine XLF Extended Life Formula TC-W3 Outboard 2-Cycle Synthetic Blend Oil very suitable for new high-displacement/horsepower carbureted or direct injection outboard motors. Pennzoil Marine XLF Extended Life Formula TC-W3 Outboard 2-Cycle Synthetic Blend Oil is formulated to provide excellent protection against piston-scuffing and reduced wear. Whether fishing or leisure boating, commercial or recreational, Pennzoil Marine XLF will help keep your investment running smooth and strong for years. Recommended for engines with oil injection systems or for pre-mix. Meets engine requirements for Johnson/Evinrude/OMC, Mercury Marine, Yamaha, Suzuki, Nissan, Force/US Marine, Mariner, and others.

• Keep your engine running clean
• Guard against harmful engine deposits
• Protect against piston-scuffing
• Keep performance-robbing carbon deposits from forming in the combustion chamber, piston tops, and under crowns and piston-combustion rings
• Keep exhaust ports clean

Product description

The 3.2-ounce bottle of Easy Mix ashless oil can be added to fresh gasoline and is appropriate for any mix ratio up to 50:1.

• For use in air-cooled 2-cycle engines
• Ashless oil formulation leaves no residue and prevents plug fouling and engine deposits
• Pre-diluted to mix quickly with leaded or unleaded gasoline
• 3.2-Ounce bottle
• For an mix ratio up to 50:1

User questions & answers

Question:	Can i use this in my weedwhacker
Answer:	Yes, you mix it with gas 50:1. I use it in my weedwacker as fuel.
Question:	Can i use this oil for my craftsman ws210- 2 cycle trimmer? please advise
Answer:	Yes you can.
Question:	how do you make 32:1 ratio with this product
Answer:	To make 32:1 ratio you need 4 ounces of oil to 1 gallon of gasoline. This bottle is only 3.2 ounces.
Question:	Is this synthetic blend or straight conventional
Answer:	Synthetic as recommended by the engine manufacturer.

Product description

STIHL 2.6-ounce high performance 2-cycle engine oil is a quality 2-cycle engine oil developed for all STIHL products and especially suitable for professional chain saws.

• 2.6-Ounce - 1 Gallon Mix
• High performance
• 2-Cycle engine oil
• Developed for all STIHL products
• Especially suitable for professional chain saws

User questions & answers

Question:	is it free shipping
Answer:	I have free shipping with Amazon prime
Question:	Is this item good for a stihl FS/90 weed eater
Answer:	No, this product is not recommended for the 4 mix engines. It will carbon up the exhaust system. Use the stihl ultra full synthetic in the silver bottle.
Question:	Can I use this in a 40:1 2 cycle craftsman weedeater
Answer:	STIHL 2.6-ounce high performance 2-cycle engine oil is a quality 2-cycle engine oil developed for all STIHL products and especially suitable for professional chain saws.
Question:	Is this oil 40 to 1 ratio or 50 to 1 ratio
Answer:	My sthl brand brush cutter manual says 40:1 oil, someone is saying all gas powered steel equipment uses 50 to 1

Product description

This product is an advanced technology tcw3 "low smoke" two-cycle oil formulated from a special blend of mineral oil, polybutene and a low ash additive system. Lucas 2-cycle racing oil is specially designed to prevent carbon deposits to the piston rings, skirt, crown and under crown areas and prevent exhaust port blocking. It is prediluted with a special solvent to facilitate mixing with gasoline's at all temperatures. Lucas 2-cycle racing oil is recommended for all air and liquid cooled tow-stroke engines and lower specific output air-cooled engines functioning under all operating conditions. Meets the requirement for "low smoke" oils often referred to as "smokeless" oils. Designed primarily for use with oil injection systems where no fuel/oil premixing is required. However, it is also acceptable for use in premixes of gasoline and oil up to 50:1. Key benefits- prevents carbon deposits - mixes well with gasoline's at all temperatures - meets requirements for "low smoke" oils.

• For best performance, follow the manufacturer's recommendations in your vehicle owner’s manual.

User questions & answers

Question:	Can it be used for an outboard boat engine
Answer:	Should work fine. It worked great in my oil-injected '83 Yamaha SS440 snowmobile. This is super high-quality 2-cycle oil, it burns clean and protects the engine really well. When I tore down my sled engine to do some upgrades, it still looked like new inside.
Question:	How about 1992 yamaha superjet 650 it doesn't say pc-w3 anywhere
Answer:	I love this oil and will continue to use it. I have a Honda 250R and it runs like a scared rabbit no issues no burning of oil. I use 36:1 ratio. Hope this helps
Question:	can this be used with an echo weed eater and leaf blower
Answer:	Absolutely! Just make sure that the oil to gas mixture is correct for whatever the implement manufacturer recommends (most often times it's 40 to 1 (gas to oil). I have been using this product for years and my lawn implements have never failed. Top notch product!
Question:	Does this stay suspended in high ethanol fuels like E
Answer:	I dont know i use only whit normal gas

Product description

Pennzoil Premium Outboard and Multi-Purpose 2-cycle Engine Oil for outboard motors is specially designed for 2-cycle gasoline marine applications and formulated to help protect outboard engines under the most severe operating conditions. This oil is compatible with outboard motors made by Johnson/Evinrude, Mercury Marine, Yamaha, Suzuki, Nissan, Force/US Marine, Mariner, Sears and all other manufacturers requiring NMMA TC-W3 oil.

• For best performance, follow the manufacturer's recommendations in your vehicle owner’s manual.
• Formulated to keep your marine engine running clean
• Also acts as a multipurpose gear oil
• Guard against harmful engine deposits
• Protect against piston-scuffing
• Keep performance-robbing carbon deposits from forming in the combustion chamber, piston tops and under crowns and piston-combustion rings

User questions & answers

Question:	can this oil be used in a 2 cycle chainsaw
Answer:	not sure I am using it in oil injected 4 wheeler ( 2 cycle)
Question:	Looking for a 2 cycle oil for an 1990 Mercury Mariner, can I use a synthetic blend in it without risking anything
Answer:	I ran it in older 1995 Johnson and a 1998 Merc 200. When I sold them and bought a new 4 stroke I gave what had left and it was a few gallons. My friend has vintage 2 stroke MC and 80s Johnson. We have had good luck with the Pennzoil blends. I get less smoke. I have also used it in actually a 35 Mariner again 80's and 2 stroke lawn equipment. Never had a problem. Be careful not to switch to straight synthetic, that can be tricky but you should be fine with blend. You can always check with the engine manufacturer. G
Question:	The picture shows 2 cycle outdoor oil multipurpose ! Can this be used for air cooled engines also
Answer:	Go to the Pennzoil Web site for more info. I have used it in my Echo line trimmer at 50/1 for about 8 hours of heavy weed whacking with no problems.
Question:	Can i use this for my 2 cycle echo 50:1 gas mixes and is it equivalent or better than the echo branded oil
Answer:	Yes. 50:1, 100:1 and better quality

Product description

If you want your outdoor power equipment to last longer and do more, you want Arnold oil products for your fuel and engine maintenance. Providing you with top-quality oil, filters, and accessories that are specific to your engine, Arnold oil products are the best way to get keep your engine functioning at its prime. Compatible with tons of major brands, 50+ years of proven performance has landed Arnold a reputation of cutting edge product innovations and extensive engineering expertise. Arnold oil products have everything you need to keep equipment running the way it should season after season. In addition to reliable, high-quality oil and accessories, Arnold’s easy-to-follow instructions and extra tips will ease your equipment maintenance and assure that you get the job done right. Stop mixing and start working with Arnold oil fuel and corresponding accessories.

• Gasoline engine oil
• For use with any 2-cycle engine with a ratio of 32:1, 40:1 and 50:1
• 2-Cycle 16 oz. Engine Oil
• Provides superior lubrication for 2-cycle air-cooled gasoline engines.
• Convenient Tip "n" Measure plastic bottle, with fuel stabilizer: holds 16 oz.

User questions & answers

Question:	Does the top part have a marking to make it easy to measure 2.6 oz
Answer:	Yes, it measures from 1.0 to 3.2 oz.
Question:	What is the shelf life of this oil
Answer:	I have been making a 40:1 mix from two of these bottles for about 5 years without any issues. This oil has fuel stabilizers added to keep the mixed gas/oil mix fresh for about a year.
Question:	Is this a synthetic 2 Cycle oil
Answer:	It is a synthetic blend, so it is not 100% synthetic. Works great in chainsaws, leaf blowers and string trimmers.
Question:	It says for all 32:1 ratio. my manual says i need 30:1. how should i mix it
Answer:	OK, per 1 gallon (=128 fl.oz.), you need (128/32) 4.0 oz. of oil for a 32:1 mix. So a 30:1 mix would require (128/30) 4.27 oz. of oil per gallon. Best of luck measuring that last quarter ounce! Frankly, I wouldn't worry overmuch about being that accurate ...

Product description

Quicksilver Premium Plus TC-W3 2-cycle oil provides superior lubrication for outboards, PWC’s, motorcycles, snowmobiles and small engines. This ashless dispercement oil fights rust deposits in the combustion chamber, intake and exhaust passages. This NMMA TC-W3 oil reduces exhaust smoke and combats carbon deposits that can cause spark plug fouling or sticking rings. The Quicksilver brand is the leader in delivering uncompromising engine oils, parts and accessories to the marine industry for over 65 years.  Quicksilver is the premier supplier of Mercury Marine Original Equipment replacement engine parts, oils, and accessories, but also works to serve all Original Equipment brands in the marine and powersports industries.  It has earned a loyal following by providing the highest quality products that are tested through some of the most rigorous environments and testing procedures. No aftermarket company comes close to the level of research and design as Quicksilver; buying Quicksilver is buying performance, protection and peace of mind.

• Advanced Quicksilver formulation provides superior lubrication to maintain peak performance for all 2-cycle outboards, PWC’s and small engines
• Produced to meet Mercury Marine original equipment manufacturer specifications to best protect your Mercury or Mariner outboard, other brands of outboards, PWC’s and small engines
• Prevents corrosion in combustion chamber, intake and exhaust passages
• Specially formulated for the severe conditions of high horsepower engines at high speed, the instant power demand for hole shots and long distance WOT operation
• For us in oil injection systems or can be used in premix for 2-cycle engines

User questions & answers

Question:	Does this product have a stabilizer in it
Answer:	Not to my knowledge
Question:	How's this compare to the royal purple synthetic? Anyone compare? I don't like smoke or smell, so want the cleanest burning
Answer:	I have not made any comparison but note that on my PWC there is no smoke.
Question:	Would this work for a Harley Davidson Iron
Answer:	This is a marine oil product. I don't know.
Question:	Is this oil synthetic or a synthetic blend type
Answer:	The product I ordered and received in August 2015 is a synthetic blend. "Synthetic Blend" is plastered on the front of the jug (but is not in the product that is pictured). I checked the product id# wondering if the wrong product had been shipped. The model # on the jug is 27Q01 and that is what the item description says they are selling.

Product features

Performance

All Quicksilver products are produced to match Mercury Marine's stringent original equipment manufacturer performance specifications.

Protection

We know what is best for your engine. We design products to fit all types of marine engines, no matter the brand.

Peace Of Mind

We validate product; quality and integrity are paramount. Buying Quicksilver is buying performance, protection, and peace of mind.

The Quicksilver Promise

Quicksilver products are designed and validated by a company that builds marine engines. We know what is best for your engine. We design products to fit all types of marine engines, no matter the brand. We validate product; quality and integrity are paramount. Quicksilver is performance, protection, and peace of mind.

Product description

Synthetic 2-cycle oil, 3.2 oz, 40:1 ratio. MTD 2-cycle engine oil for Troy-Bilt, MTD, Yard-Man, Bolens, Huskee, Yard Machines

• Synthetic 2-cycle oil
• 3.2oz (95ml), 40:1 ratio
• For Troy-Bilt, MTD, Yard-Man, Yard Machines, Bolens, Huskee
• 4 oz. Bottle of 2-cycle oil
• For use with all 2-cycle models
• Ideal for air-cooled 2-cycle engines requiring 32:1 ratio

User questions & answers

Question:	Does it works with poulan
Answer:	Works with any engine requiring a 40:1 gas to oil mix.................some are 30:1 so be sure yours is 40:1 ratio...........it should show somewhere on the saw!
Question:	can this oil be used in gasoline for a 2 stroke outboard engine
Answer:	I would use the engine manufactures recommended oil to help ensure there would be no warranty issues.
Question:	In what country is this 2-cycle oil made
Answer:	Well, it says Made in the USA, now whether its completly manufactured in the USA is anyone's guess, but at least part of it is to get the label
Question:	Can you use it for stihl motors
Answer:	Check on your weed trimmer or blower and see if it says use 40:1 2 cycle oil. Some call for 50:1. Must be mixed with exact 1 gal of gas.

Product description

Valvoline Outboard 2-Cycle Marine Engine Oil is a superior quality NMMA certified ashless two-cycle lubricant. Premium base stocks are blended with a modern ashless detergent additive package to provide fortification for maximum performance in outboard engines. It is pre-diluted for ease of mixing with gasoline and may also be used in direct fuel injection systems. This product is recommended for all leading outboard engines, including the latest high horsepower units direct fuel injection models. Valvoline Outboard 2-Cycle Marine Engine Oil will also provide excellent performance in twocycle engines of motorcycles, all-terrain vehicles, snowmobiles and personal watercrafts. It may be used at manufacturers recommended fuel/oil ratios from 11:1 to 100:1

• Designed to help minimize wear, combustion chamber deposits, ring sticking, piston burning, port blocking and spark plug fouling
• Formulated to enhance engine performance
• Helps prolong engine life
• Meets and/or exceeds requirements of all leading engine manufacturers where an NMMA TC-W3 certification or preceding specification is recommended

User questions & answers

Question:	I looked at the answers. Two people say they receivec a single bottle. One says it's a 3 pack. Anyone else order this
Answer:	Its a single big bottle.i used it for my scooter its a 2 stroke..i hope i cover you
Question:	Can this product be used with chainsaws
Answer:	This is a gas mix for 2-cycle engines. If your chainsaw is a 2-cycle engine and your looking for a fuel mix, that's what this is for then, yes.
Question:	Is this a synthetic blend
Answer:	No It is plain petroleum based
Question:	Anyone running it a jetski any difference (yamaha gp
Answer:	i used it for a scooter 2 stroke and it was working perfect.now for a jet ski i don't know if its a 2 stroke it will work...

Product description

Toro 2 Cycle Oil (2.6 oz)

• Low Smoke
• Fuel Stabilizer Added
• Genuine OEM Toro Parts

User questions & answers

Question:	Is this toro oil still nmma tcw iii-certified ? it does not state this on the label. also, why are there black and white bottles available? thanks
Answer:	Beats me.
Question:	Gear starter for toro
Answer:	Not sure what you are asking. This is a gas treatment for Toro 2 cycle machines. In my case a trimmer and snow blower.
Question:	Need 32_1 mix, for older Toro snow blower
Answer:	This is 50/1 but you could use more to make it 32/1. Just have to do your own match.