12 best solar controller with usbs

Product description

☀️Suitable for farm solar power system, solar street light, solar patio light, solar billboards, outdoor camping solar system, ship solar system.

Specification:

*Batt voltage: DC 12V/24V Auto

*Charge /Discharge current: 20A

*Over discharge Protection: 10.7V/21.4V

*Charge recover voltage: 12.6V/25.2V

*Overcharge Floating charge: 13.7V/27.4V

*Over discharge Protection: 10.7V/21.4V

*Equalization: B01: sealed 14.4V / B02: Gel 14.2V / B03: flood 14.6V



Intelligent solar controller:

The product can automatically manage the working of solar panel and battery in solar system. For protecting the lifespan of your battery, once the voltage of the battery drop below 8V, the solar controller will turn off automatically (LCD will be unavailable at the same time).



Easy to operate and installation :

Wiring STEPS: Screw the adjustment screw counter-clockwise until the plates move down. Insert the wire into the new opening between the plate and the "top" of the Terminal hole, not under it. Screw the adjuster clockwise and the plate will move upwards thereby squishing the wire in the Terminal hole.

Installation STEPS：Connect the system in the order of 1.Battery > 2. Load > 3.PV Array in accordance with Figure, and disconnect the system in the reverse order 3. 2 .1.



Note:

<1>Please keep it in cool and well ventilated place to maintain good heat dissipation.

<2>the regulator is only suitable for lead acid batteries:OPEN, AGM, GEL, not for nickel hydride, lithium, ions, or other batteries.

<3>Make sure your battery has enough voltage for the controller to recognize the battery before first installation.

<4>The working temperature of this controller is -35°C to 60°C, during hot sunny days, the temperature outside might go up to 60-75°C. Please do keep the controller stay in cool and well-ventilated place to maintain good heat dissipation.

• ☀☀☀20A Solar Charge controller : Binen solar charger controller are UL 1741 certified,the solar charger controller compatibility with 12V 24V system. Discharge Current: 10A,build-in industrial micro controller, automatically manage the working of solar panel and battery in solar system. Dual USB output 5V/2.5A (max), to support mobile phone chargeing.
• ☀☀☀Multiple Protection Functions: Binen solar controller has short-circuit protection, open-circuit protection,reverse protection, over-load protection. Fully 3-stage PWM charge management, improve system efficiency and prolong the life span of the battery.
• ☀☀☀Battery Type: The charge regulator is only suitable for lead-acid batteries: OPEN, AGM, GEL, it is not suited for nickel hydride, lithium, Liions, or other batteries. For protecting the lifespan of your battery, once the voltage of the battery drop below 8V, the solar controller will turn off automatically.
• ☀☀☀LCD Display: Comes with a display that can clearly indicate the status and data, it can be conveniently switched modes and parameter configuration, suitable for home, industrial, commercial etc.
• ☀☀☀Easy to Install and Operate: The charge controller should connect the battery first, then the solar panel, and finally the load! The disassembly sequence is contrary to the wiring order.Dual mosfet Reverse current protection, low heat production. ( Note: The charge controller will heat up when it is running. Please be careful to install the charger controller on a flat, well-ventilated place)

Product features

20A solar charger controller

*Rated Voltage: 12V/24V

*Discharge current: 10MA

*Max. PV Voltage: 50V

*Max input power and voltage: 260W /12V; 520W/24V

*Floating charge: 13.7V/27.4V (defaul)

*Discharge Stop: 10.7V/21.4V (defaul)

*Charge recover voltage: 12.6V/25.2V (defaul)

*Load Mode: 24 hours, 1-23 hours, 0 hour

How to adjust the float voltage?

Step 1: The system default float voltage is 13.7V, but you can change it according to your needs. Press MENU to enter the parameter page and find the floating charge voltage page.

How to adjust the float voltage?

Step 2: In floating charge voltage interface long press 3-5 seconds MENU to enter setting and using UP or DOWN to set the floating voltage

Product description

usb rs232 cable for srne mppt solar charger controller SRNE ML2430 Solar charger console cable

ftdi chip

Support USB RS232 driver for windows 7/8/8.1/10driver, Mac, Android

1024 byte EEPROM, support re-write VID, PID, etc



Drivers are available which allow FTDI devices to work with the following operating systems:

Windows 8.1 Windows 8.1 x64 Windows 8

Windows 8 x64

Windows Server2012 Windows Server 2008 R2

Windows 7 Windows 7 x64

Windows Server 2008 Windows Server 2008 x64

Windows Vista Windows Vista x64

Windows Server 2003 Windows Server 2003 x64

Windows XP Windows XP x64

Windows ME Windows 98

Linux

Mac OS X Mac OS 9 Mac OS 8

Windows CE.NET (Version 4.2 and greater)

Android

Windows RT

Support for WinCE7.0

Installation Guides If you need further support about how to pick up and install drivers, please goes to

http://www.ftdichip.com/Support/Documents/InstallGuides.htm

Package:

1 x usb to 6P6C RS232 Serial Cable with FTDI chipset

• usb rs232 cable for srne mppt solar charger controller SRNE ML2430 Solar charger console cable
• Geniue FTDI Chipset , Cable Length:6ft
• 1024 byte EEPROM, support re-write VID, PID, etc
• Environment PVC, 26/28AWG wires, Pure Copper
• System Support: All windows system, Win7/8/10/xp/mac/linux/android, environment PVC jacket & pure copper wires, Central Package

Product description

The Renogy Wanderer 10A solar charge controller integrates efficient PWM charging to increase battery life and improve system performance. Designed with a simple interface for ease of use the controller uses an LCD to notify users of battery information. This advanced charge controller is designed for off-grid solar applications and can be used with a 12V/24V battery or battery bank. The compact size of the controller makes installation a breeze. The controller comes equipped with fully comprehensive self-diagnostics and electronic protection functions to prevent damage from installation mistakes or system faults.

• Optimized for a 12V/24V system; Deep Cycle Sealed (AGM), Gel, Flooded and Lithium battery option ready.
• Smart 4-Stage PWM charging (Bulk, Boost, Float, and Equalization) increases battery life and improves system performance. Intelligent protection against reverse polarity, overcharging, short-circuit, and reverse current.
• Backlit LCD screen displays system operation, diverse load control, and error codes.
• Integrated 5V 2A USB ports to charge USB devices. Compact in size makes it easy to install virtually anywhere.
• Capable of charging over-discharged lithium batteries. Integrated RS232 port allows communication with BT-1 Bluetooth module and usage of Renogy DC Home smartphone app.
• Power Source Type: Solar-Powered
• Wanderer10A|30A Installation Notes: The default starting position of the Wanderer controller terminal hatches are closed (in the UP position) that could mistakenly look like an open wire hatch. Make sure to FIRST lower each terminal hatch by screwing the terminals counterclockwise (CCW) to expose the wire terminal hatch to the open position. THEN secure each cable by rotating the screws clockwise (CW) to the closed position.
• Simple Install: Fully open the hatch (CCW), insert the appropriate wires, and completely close the hatch (CW).

User questions & answers

Question:	Is there a way to adjust the float voltage on this unit
Answer:	No, the float voltage on mine is 13.8V no matter the battery type setting. There is a manual on the Renogy website that lists float at 13.2V when set for Flooded batteries. However that is not the case on my unit, which I bought in 2016.
Question:	Can anyone explain the middle led's lighting sequence? What are the possible states of display, blinking, on, what do they mean
Answer:	The middle LED's lighting sequence is as follows: Green ON when battery level is in the right range. Green slowly flashing when battery level is full. Yellow ON when battery level is low. Red ON when loads cut off. Hope this helps.
Question:	max number of 100w panels for this controller
Answer:	This will depend on 2 things: 1 - what is the amp rating of your controller. &. 2 - what is the nominal voltage output of the panels. A 30 amp controller can handle a maximum of 3.6 100 watt panels of 12 volts (100 watts / 12 volts = 8.33 amps, 30 amp controller / 8.33 amp panel = 3.6 panels per controller). Of course, you can't have .6 panels so the safest load would be 3 panels. Yes, math is VERY IMPORTANT when being safe with electronics.
Question:	The description says "These are Positive Ground Controllers." How do you ground a system on the positive side
Answer:	Please ignore this if you're not interested in a dissertation on grounding. First, THIS is a NEGATIVE "ground" controller, so that's GOOD. Why? "Ground" is a misleading term. I've designed stuff for NASA spacecraft that had connections called "ground". Whaaat? We're going to run an extension cord to the spacecraft, so we can keep it tied to a metal pipe stuck in the dirt? Nope. "Ground" is just what electronics folks usually call a COMMON POINT the circuitry is referenced to. It doesn't necessarily have anything to do with the ground we walk on. Electrical stuff works by having two sides, positive and negative, with a voltage difference between them, the "pressure" that makes current flow. Electrical power folks tie one side to the dirt your house sits on, for safety. Your house has water pipes and stuff that's pretty well connected to the dirt. If you grab a water pipe and the 110V ground at the same time there's no voltage difference, so current doesn't flow through you and hurt you. 110V is 10x higher than a solar panel voltage so it's a lot more dangerous. Tying one side to the dirt was a very good idea. Long, long ago, and far, far away, electrical power folks chose the negative side to connect to the dirt, and most stuff made since has pretty much matched that. Then some folks decided to make "positive ground" devices, because for their designs it was easier and cheaper. Some of us think they should have been spanked. It caused all this "positive ground" and "negative ground" malarkey. On to solar power systems. Think of it like this: A controller has electronically controlled switches in it. One switch connects the solar panel to the battery to charge it and disconnects when the battery is full. Another switch connects the load to the battery when you want the load turned on. In a "negative ground" system, the terminals of the panel, battery and load called "minus" or "negative" are all tied together, and the controller switches the positive side connections. Since many loads are connected together on the minus side to ground (dirt) this is a GOOD THING. In a "positive ground" system it's the opposite. The positive side of everything is tied together, and the controller switches the negative side connections. Imagine this: If you connect the battery negative terminal and the load negative terminal both to ground (shorted together) and the controller switch is between them, what happens when the switch opens? That's right, NOTHING. The switch is shorted out by your ground connections so it can't disconnect the load. So that's what's wrong with a positive ground controller. Everyone is used to tying negative together and to ground and they do that and it screws up the controller. But a positive ground controller can be used as long as you don't connect the battery and panel to *anything* except the controller. For example, your van's battery negative is connected to the chassis of your van, and so are the negative sides of all the lights and devices in your van. JUST DON'T TIE THE SOLAR PANEL OR SOLAR BATTERY NEGATIVES TO YOUR VAN CHASSIS TOO. You CAN tie the controller's load output negative to your van chassis, as long as you don't connect any. other. point. in the solar charging system to chassis too. With a "negative ground" controller you don't have to worry about any of this malarkey. You can tie the battery, panel, load negatives all to chassis without any problems. This is why NEGATIVE GROUND CONTROLLERS ARE BETTER. Sorry for the lengthy explanation. I hope folks can follow this and it helps them understand this "ground" stuff.

Product features

Renogy Wanderer

The Renogy Wanderer 10A solar charge controller integrates efficient PWM charging to increase battery life and improve system performance. Designed with a simple interface for ease of use the controller uses an LCD to notify users of battery information. This advanced charge controller is designed for off-grid solar applications and can be used with a 12V/24V battery or battery bank. The compact size of the controller makes installation a breeze.

Specification

Layout

1. LCD Screen
2. Select Button
3. Enter Button
4. USB Ports
5. Load Terminal
6. Battery Terminal
7. PV Terminal
8. RS232 Communication Port

RS232 Communication Port

Integrated RS232 port allows communication with BT-1 Bluetooth module (Not Included) and usage of Renogy DC Home App.

Compatible Battery Types

1. Sealed
2. Gel
3. Flooded
4. Lithium

USB Port

5V 2A USB Ports

• ❶【Multi-Function Four USB 40A MPPT Solar Charge Controller】 Using innovative MPPT technology high tracking efficiency up to 97%;
• ❷【LCD Displays】This controller is 12V/24V automatically adapt,first connect the battery,then connect the solar panels,when you first use it, make sure the battery has enough voltage,so that the controller can recognize the correct battery type
• ❸【Reliable Protection】overvoltage, short circuit, overload, overcharge, over discharge protection function;Automatic focusing MPPT tracking charging, high charging efficiency,Non-stop detection during charging, bidirectional focusing tracking
• ❹【Industrial-grade Master Chip】16AD sampling accuracy, temperature Charging current, discharge current accurate real-time display, power generation at a glance.RS-485 communication bus interface and Modbus communication protocol, available to meet various communication requirements in different situations
• ❺【Please Attention】Pls note the connection ways,Connect the battery first,then connect the solar panel(You can't reverse the order).The place that don't understand pls contact us,Thanks!

Product features

About Our Mppt Solar Controller

The MPPT controller is a solar charge controller with maximum power point tracking function;

They are suitable for solar charging and load charging control of batteries or battery packs;

Suitable for wide-voltage off-grid solar systems; MPPT charging controller will be the most advanced charging technology;

Combined with efficient and professional battery maintenance, it has numerous programming options, complete protection functions and an intuitive LCD display

Fetures

• 1.12V / 24V voltage automatic switching
• 2.40A load output High power and high efficiency (maximum rated power 38-40w)
• 3.Multistage charging technology Three kinds of batteries are available: lead acid battery, ternary lithium battery, lithium iron phosphate battery
• 4.CE,ROHS certification, ISO9001 quality system requirements
• 5.Multiple protection:Over charge ,Deep discharge ,Short-circuit ,Battery Open circuit ,Overheat temperature ,Battery overpressure over current protection

Unique Design

• This Solar Panel Charge Controller with RS485 interface , it can be monitored by cellphone APP(eBox required) , PC Software and MT50 remote meter.
• It available to meet various communication requirements in different situations
• Wide range of applications: Mainly used for RV solar panels, large-scale solar panel power generation systems, solar panel environmental protection street lights, yachts and ships, etc.
• Aviation alloy heat dissipation backplane: Prevent the equipment from generating heat for a long time, and effectively cool down and protect the electrical appliances
• ABS flame-retardant and high-temperature resistant shell: It can resist heat and deformation, and also has impact resistance under low temperature conditions, not easy to scratch, and not easy to deform

LCD Screen Display

• LCD Screen (operation interface, parameter setting, and other contents are displayed)4
• USB fast charging

Package included:

• 1 pc 40A Mppt Solar charing Controller

Product description

Features:

Automatically manage the working of solar panel and battery in solar system.



Dual USB output, the maximum current of 2.5A, to support Apple mobile phone charging.



Build-in short-circuit protection, open-circuit protection, reverse protection, over-load protection.



Prolong the battery life cycle and keep the load work well.



Easy to set up and operate.



Suitable for small solar energy system.





Product Specification:

Type: Solar Charge Controller



Material: ABS



Screen: LCD display screen



Battery Voltage: 12V / 24V



Charge Current: 30A



Working Temperature: -35 to 60 degree Celsius



Self consume: 10mA



Float Charge: 13V



Discharge stop: 10.7V



Discharge reconnect: 12.6V



USB output: 5V/2.5A





Connection steps:



1.Connect the battery to the charge regulator - plus and minus.



2.Connect the photovoltaic module to the regulator - plus and minus.



3. Connect the consumer to the charge regulator - plus and minus.



NOTE: The reverse order applies when deinstalling. The wrong connection sequence will damage the controller.

• 【Build-in industrial micro controller】automatically manage the working ofsolar panel and the battery in solar system to support charging.
• 【Wide Compatibility】The solar charger controller with 30A rated discharge current is compatible with 12V or 24V system automatically, suitable for lead-acid batteries: OPEN, AGM, GEL. Dual USB 5V/3A output ports support mobile phones, tablet PCs or other devices that require 5V voltage.
• 【Multiple Protection Functions】Over-current and short-circuit protection, inverse connection protection, low voltage and overcharge protection. Fully 3-stage PWM charge management, improve system efficiency and prolong the life span of the battery.
• 【Good Heat Dissipation】Dual mosfet reverse current protection, low heat production(ALL electronic components generate heat when they are running,it is better to shelter them for better heat dissipation, avoid direct sunlight exposure or damp place).
• 【Easy to Use】The charge controller should connect the battery first, then the solar panel, and finally the load!Big LCD display, adjustable parameter, suitable for home, industrial, commercial etc.

Product description

Product Features:

*30A Solar Charge Controller: Build-in industrial micro controller, automatically manage the working of solar panel and battery in solar system. Dual USB output 5V/2.5A (max), to support Apple mobile phone charging.



*LCD Display: clearly indicate the status and data, it can be conveniently switched modes and parameter configuration, parameters adjustable， suitable for home, industrial, commercial etc. adjustable parameter.



*Multiple Protection Functions: EEEkit solar controller has short-circuit protection, open-circuit protection,reverse protection, over-load protection and fully 3-stage PWM charge management, improve system efficiency and prolong the life span of the battery.



*Easy to Install and Operate: Battery --->Solar Panel ---> Load. The disassembly sequence is contrary to the wiring order.



*with Timer Function: You can set the on/off and a certain number of hours as you like, without extra worry, it is convenient for your life.



Q&A

1.Q: How to install it?



A: The charge controller should connect the battery first, then the solar panel, and finally the load. The disassembly sequence is contrary to the wiring order.



2.Q: Without using a battery, can it be wired to an inverter and work directly from that?



A: Sorry no. A solar panel can't run a inverter with out a battery.



3. Q: What type of battery do I need?



A: Battery Type: The charge regulator is only suitable for lead-acid batteries: OPEN, AGM, GEL, it is not suited for nickel hydride, lithium, Liions, or other batteries.



Any question, please feel free to ask us.



Package Includes: 1 x Solar Charge Controller. 1 x User Manual.

• 🥇30A Solar Charge controller : First solar charger controller are UL 1741 certified,the solar charger controller compatibility with 12V 24V system. Discharge Current: 10A,build-in industrial micro controller, automatically manage the working of solar panel and battery in solar system. Dual USB output 5V/2.5A (max), to support mobile phone chargeing.
• 🥇Multiple Protection Functions: First solar controller has short-circuit protection, open-circuit protection,reverse protection, over-load protection. Fully 3-stage PWM charge management, improve system efficiency and prolong the life span of the battery. For protecting the lifespan of your battery, once the voltage of the battery drop below 8V, the solar controller will turn off automatically.
• 🥇Battery Type: The charge regulator is only suitable for lead-acid batteries: OPEN, AGM, GEL, it is not suited for nickel hydride, lithium, Liions, or other batteries. For protecting the lifespan of your battery, once the voltage of the battery drop below 8V, the solar controller will turn off automatically.
• 🥇LCD Display: Comes with a display that can clearly indicate the status and data, it can be conveniently switched modes and parameter configuration, suitable for home, industrial, commercial etc.
• 🥇Easy to Install and Operate: The charge controller should connect the battery first, then the solar panel, and finally the load! The disassembly sequence is contrary to the wiring order.Dual mosfet Reverse current protection, low heat production. ( Note: The charge controller will heat up when it is running. Please be careful to install the charger controller on a flat, well-ventilated place)

User questions & answers

Question:	Will this work with lithium ion batteries
Answer:	the lock is like a regular post box in a condo building. they sell them at home depot
Question:	Hook directly to positive on the battery
Answer:	Hello, it will depend on your preference, but three inch house numbers will fit nicely. Thanks for reaching out!

Product description

Product specification:

Rated charging current: 10A

Rated charging voltage: 12V/24V automatic

Voltage tolerance: ±0.3V

Low voltage shutdown: 10.7V/21.4V

Floating voltage: 13.7V/27.4V

Low voltage recovery: 12.6V/25.2V

Standby current: ≤30mA

Load voltage drop: ≤170mA

Charging mode: PWM Mode

USB output: 5V/4A

Working environment temperature: -10°C~50°C

Mounting hole size: 126*69mm

Product size: 134*83.5*35mm

Product weight: 185g

Product Features:

• 10A solar controller: Built-in industrial microcontroller, which can automatically manage the work of solar panels and batteries in solar systems.
• The solar charger controller with a rated discharge current of 10A is automatically compatible with 12V or 24V systems and is suitable for OPEN, AGM, and GEL lead-acid batteries. 4 USB 5V/3A output ports support mobile phones, tablets or other devices that require 5V voltage.
• LCD display: Clearly indicate status and data, can easily switch modes and parameter configuration, parameters can be adjusted, suitable for household, industrial, commercial and other adjustable parameters.
• Multiple protection functions: BYGD solar controller has short circuit protection, open circuit protection, reverse protection, overload protection and full 3-level PWM charging management, which can improve system efficiency and extend battery life.
• Easy to install and operate: The charge controller should be connected to the battery first, then to the solar panel, and finally to the load! You can change the settings with a simple one-button operation.

Packing list:

1 10A solar controller

1X English User Manual

• 【Wide Compatibility】The solar charger controller with 10A rated discharge current is compatible with 12V or 24V system automatically, suitable for lead-acid batteries: OPEN, AGM, GEL. 4 USB 5V/3A output ports support mobile phones, tablet PCs or other devices that require 5V voltage.
• 【Multiple Protection Functions】BYGD solar controller has short-circuited protection, open-circuit protection, reverse protection, over-load protection. Fully 3-stage PWM charge management, improve system efficiency and prolong the life span of the battery.
• 【Intelligent】Build-in industrial microcontroller for automatical management, memorizing various parameters set by the user and the data won't be lost when the battery runs out. The solar controller will turn off automatically once the voltage is too low.
• 【Functional LCD Display】Comes with an intuitive LCD display that can clearly indicate the status and data, it can be conveniently switched modes and parameter configuration, suitable for home, industrial, commercial, etc.
• 【Easy to Use】The charge controller should connect the battery first, then the solar panel, and finally the load! You can change the settings by the simple one-button operation.

User questions & answers

Question:	Does it really have a backlit LCD
Answer:	Yes, it is laminated with a durable, 3mm plastic lamination film. Inside is a full color, high quality paper poster. Hope this helps!

Product description

EPEVER PWM 30A solar charge controller is a common positive PWM charge controller with built in LCD display that adopts the most advanced digital technique. The multiple load control modes enable it can be widely used on solar home system, traffic signal, solar street light, solar garden lamp, etc.

Specifications:

Model:VS3048AU 30A 12/24/36/48V auto work ,Max Input solar panels 360W/720/1080W/1440W

Battery input voltage range: 9V～64V

Rated charge/discharge current:30A

Max. PV open circuit voltage: 96V

Terminals: 3AWG(25mm2)

USB output: Max. 5VDC/2.4A

Battery type: Sealed(Default) / Gel / Flooded

Boost charging voltage:Gel: 14.2V, Sealed: 14.4V, Flooded: 14.6V

Equalize charging voltage:Sealed:14.6V/ Gel: No/ Flooded:14.8V

Float charging voltage:Sealed/Gel/Flooded:13.8V

Low voltage reconnect voltage:Sealed/Gel/Flooded:12.6V

Low voltage disconnect voltage:Sealed/Gel/Flooded:11.1V



Features:

● 3-Stage intelligent PWM charging：Bulk, Boost/Equalize, Float

● Support 3 charging options: Sealed, Gel, and Flooded

● LCD display design, dynamically displaying device’s operating data and working condition

● Double USB design, the power supply charge for electronic equipment

● With humanized button settings, operation will be more comfortable and convenient

● Multiple load control modes

● Energy statistics function

● Battery temperature compensation function

● Extensive Electronic protection



Electronic protections:

● PV reverse polarity protection ● Battery over voltage protection ● Battery over discharge protection ● Battery reverse polarity protection ● Battery overheating protection ● Load overload protection ● Load short circuit protection ● Controller overheating protection



Package :

1X 30A VS3048AU solar charge controller

1X Manual

(RTS300R47K3.81A)3m Temp sensor cable *1

• EPEVER PWM solar charge controller 30 Amp, 12V/24V/36V/48V Auto Wrok ,Max PV 96V ,Max Input solar panels 360W/720/1080W/1440W , Double USB design , 3-Stage intelligent PWM charging：Bulk, Boost/Equalize, Float . Support 3 charging options: Sealed, Gel, and Flooded
• LCD display design, dynamically displaying device’s operating data and working condition . the power supply charge for electronic equipment
• With humanized button settings, operation will be more comfortable and convenient . Multiple load control modes
• Energy statistics function . Battery temperature compensation function ,Extensive Electronic protection
• (RTS300R47K3.81A) 3m Temp sensor cable *1 will be free gift for you . Please feel free to contact with us , we could supply technical support and free solar system design , 2 years warranty .

User questions & answers

Question:	Will the 60 amp controller handle 88v dc pv input using a 12 volt battery setup
Answer:	Hello, thanks for your question. Yes. we will supply different resistance.Please contact our customer to learn more details,if you need others.
Question:	I new in the solar, 3048 work from my 225w and 36v panel to connect to 12v battery
Answer:	This is really a good question, after testing by our quality inspection department, our resistance band can stretch 141 inches, which is very safe.
Question:	Will the 6048au controller handle 1350 watts with a 12 volt battery system without burning up the controller
Answer:	TITISKIN made of eco-friendly PU FOAM，There will be some smell just after opening the package, put it out few hours and it almost has no smell.
Question:	what's the max current load can load handle is it adjustable
Answer:	I suggest that it is suitable for your height. It's not about weight. And it has a place to hold it. It's comfortable. I think it's suitable for all adults.

• Automatic 12V or 24V system detection for batteries. 3 pre-set deep cycle battery options: Gel, Flooded, and Sealed Lead Acid/AGM.
• An upgraded 3-Stage PWM charging algorithm is adopted: Bulk, Boost, Float
• With temperature compensation employed, charging parameters can be automatically adjusted.
• Adapt to 1 100W Solar panel or 2 to 3 100W Solar panels in parallel.
• Integrated LCD screen and 2 key user-interface. Intergrated USB function for supplemental charging.

User questions & answers

Question:	On the 10 amp controller battery mode does SEL stand for sealed
Answer:	Yes, it includes an easy to use foot pump - which works a lot better, quicker, and less effort than the hand pump.
Question:	Can this work with an 18VDC 7 watt solar panel
Answer:	My daughter uses this ball as an office chair every day due to back issues and on the advise of her physical therapist. It is working well. She is tired at the end of the day but feels her core is strengthening and very effective. It sits tall about the same height of an office chair.
Question:	If I connect the solar and battery correctly, how does positive or negative ground have any importance
Answer:	The Summit 60 kit includes everything in the ultimate P.volve kit plus the precision foam roller and the p.3 trainer.
Question:	What is the maximum watts imput to this 30 amp charge controller at 12v? And what is the maximum volts at 12v
Answer:	There are no DVDs included in this kit. There is a 30-day free trial to P.volve streaming that is included.

Product features

HQST Controller

This controller is an intelligent and multifunctional solar charger controller. These serial products adopt customized LCD display screens, which make operations on the interface rather convenient. All of the controlling parameters can be reset to satisfy user needs.

System connection

1. Connect the battery to the charge controller

2. Connect the solar panel to the controller

Can be connected to an external devices

Features a 5V 1A USB output that can be used to charge mobile phones, tablets, speakers, etc. A wide range of load working modes facilitate the product's application to different types of load.

Battery Types

AGM, GEL, FLOODEDand ACID battery for selection.

Product description

Safety Instructions:

A) Make sure your battery has enough voltage for the controller to recognize the battery type before first installation or adjusting default parameter, too low voltage battery won’t activate the controller.

B) The solar charge controller can be charged for lead acid batteries (Sealed, Flooded, AGM, GEL),3S or 6S lithium ion and 4S or 8S lifepo4 batteries, but you need to confirm battery type as quick as possible after controller is activated.

C) The charge controller is only suitable for regulating solar panels. Never connect another charging source to the charge regulator.

D) Disconnect all sources of power to the controller before installing or adjusting, and don’t disconnect battery during charging, because it may causes a brief pike in load voltage which may damage sensitive equipment.

E) The battery cable should be as short as possible to minimize loss. Use only well-isolated tools.

F) Please keep it in cool and well-ventilated place to maintain good heat dissipation



How to connect solar system with the controller:

Step 1: Connect the battery to the solar charge controller firstly- plus and minus.

Step 2: Connect the load to the controller secondly.

Step 3: Connect the solar panel to the controller finally - plus and minus.

The reverse order applies when de-installing.



Specification:

Main Color: Blue

Rated Charging Current:40A

Rated Discharging Current:40A

Max Solar Input Voltage: ＜50V

System Voltage:11.1V/12V/12.8V/22.2V/24V/25.6V

Stand-by Lost: ＜15mA

Battery Type: 12V/24V Lead Acid, 3S/6S Lithium Ion,4S/8S LifePo4

Operating Temperature: -20 ~ +50℃

Storage Temperature: -30 ~ +70℃

Maximum Wire Size:6AWG

Size/Weight: 186x90x50mm/370g

USB Output: 2pcs x 5V/2A (max)



Package Include：

1 X 40A Solar Charge Controller with LCD screen

1 X User Manual

• Can charge 3 types of batteries: Lead acid batteries (including Flooded, Sealed, AGM, GEL), 3S/6S Lithium ion batteries and 4S/8S LiFepo4 batteries. (Default battery type is for lead acid battery, customers need to set for other battery type)
• With multi-functional LCD display, it dynamically displays all the operating data and working condition, working modes, and parameter configuration can switched conveniently by pressing 3 yellow buttons.
• Have 3 kinds of load working mode for your choice: 24hours load on mode, Dawn to Dark mode, and Timer mode based on D2D. (Default load working mode is 24 hours)
• Build-in industrial micro PWM solar controller,some voltages and working modes of loads can be adjustable.
• With dual 5V/2A max USB Output and deep heat sink, you can apply this solar charge regulator to many solar systems, such as solar street lighting, home power station, outdoor monitoring, RV, Camper,Boat or Caravan solar systems or other solar systems.

User questions & answers

Question:	Will 3-130w12v&1-50w12v solar panel work if panels are parallel w/2 12v100aH lithium batteries on this charge controller?What size fuse is needed
Answer:	No it didn’t come with that
Question:	Would this work with two 12v 12s lifepo batteries in series
Answer:	I'm not aware of any phone apps that will allow you to rip MP3 files to a USB. However there are multiple players, cassettes, vinyl and CD's that have the ability to create MP3 files from the analog media. I suggest that you search Amazon for those devices. Alternately you you can hook up a player to the Boytone and play regular media through the board. Good luck.
Question:	My life pro4 batteries are down to 50%. My panels will put out 12 amps but your controller will only allow 7.5 amps to charge batteries. Advise pleas
Answer:	No there is no sand in it
Question:	Is the 30a charge rate the maximum? would it damage a lifepo4 battery that has a max charge rate of 10a
Answer:	It is surprisingly complicated for something that should be obvious. First, the pump has two tips attached to it: one has a closed end don't use this, the second has a small opening. Attach the second tip to the pump and insert it into the ball. Also, be sure that the air hose is connected correctly to the pump so that air is going in not pulled out. It takes awhile before you can see that the ball is actually inflating. When the ball is fully inflated there are two white plastic pint short spikes with a wide disc base these is the plug for the inflate hole. It was after I inserted it that I realized that the funny looking giant white plastic paper clip looking thingy is the tool to remove the plastic valve plug if you need to. Also, there is a white measuring tape that is supposed to be used to measure the correct diameter -I can't help you here, I have no idea how it should be used, when my ball was fully inflated the tape showed that I needed another 12"! Otherwise I love the ball - I use it as a chair at my desk all day.

Product description

Function:



Always keep the battery on fill voltage condition.

Reverse Polarity Protection for Battery

Reverse Polarity Protection for Solar Panels

When the battery voltage is low, the controller will automatically cut off the load from the system. If the voltage of battery is back to normal and the load will restart working.

Thunder protection

According to the battery voltage grade, the controller can automatically set charge-off voltage, the load-off voltage, the load- restore voltage. (The parameter is default under 25℃ condition, locked by the CPU procedure, cannot adjust.)

The controller will automatically compensate the temperature of the charging voltage according to the changes of ambient temperature.



Package Includes：



1 x Solar Panels Battery Charge Controller

1 x User Manual



★★Note★★ ：

➹ About delivery:

The whole delivery usually takes about 4-7 days , but it sometimes might be delayed 1-2 days by the bad weather or other factors , really need your understanding.

➹ About color:

Pictures are only samples for reference. Due to limitations in photography and the inevitable differences in monitor settings, the colors shown in the photograph may not correspond 100% to those in the items themselves.

➹ About service:

If there is any problem about the quality or the defective items , please feel free to contact us (Autoday), we will try our best to solve your problem within 24 hours.

• ✔️ --- NOTE: The regulator is only suitable for lead acid batteries: OPEN, AGM, GEL. It is NOT suited for nickel metal hydride, lithium ions or other batteries.
• ✔️ --- MPPT solar charge controller MPPT10-60: Compared with normal solar charge controller, this MPPT controller could increase efficiency by 10%-30%.
• ✔️ --- When the battery voltage is low, the controller will automatically cut off the load from the system. If the voltage of battery is back to normal and the load will restart working.
• ✔️ --- This MPPT controller has perfect SOC function, control charge current, and supply power to the loads.Prevent the battery from over-charging , over-discharging and reverse charging to solar panels during nights.
• ✔️ --- Any problem please contact with us , we will try our best to solve your problem and make you satisfied within 24 hours.

User questions & answers

Question:	How many amps in a 100 watt solar panel
Answer:	A "12 v" 100 watt panel has various ratings: The "peak power" output will be roughly 18 volts at 5.56 amps (using a Grape polycrystalline as an example) But its short-circuit (Isc) current will be 6.13 amps. (at zero volts) (to be complete: its open-circuit voltage will be 22 volts, at zero amps) Those voltage and current number can be slightly exceeded depending upon temperature and amount of sun.
Question:	Can this handle 900 watts of solar without buring or heating up
Answer:	I only have 300 watts on it and it gets quite hot.
Question:	Should the controller unit be grounded? Using it to run 2 5amp lights
Answer:	Yes
Question:	Pwm or mppt ? The product description states that this unit is an mppt, the user manual states it is pwm
Answer:	it has all the pwm functions and it is better than pwm

Product description

Parameters:

Batt voltage: 12V/24V auto

Charge current: 40A

Discharge current: 40A

Solar open voltage: < 23V @ in 12V battery / 45V @ in 24V battery

When using a PWM charge controller, it is recommended that the PV panels be connected in parallel, preferably not in series. The series voltage easily exceeds the maximum input range.



Max input power: 450W /12V system, 900W/24V system

(The input power of the PWM controller should not exceed 75% of the controller, which can extend the life of the controller.)

Battery type: GEL,LEAD-ACID,FLOODED



Load Mode：

a. 【24H】 hours

b.【1-15H】 hours

c. 【0H】hour

【1-15H】and 【0H】both belong to the light control mode, and the load is turned off after dawn.



Float charge: 13.7V(defaul,adjustable)

Discharge stop: 10.7V(defaul,adjustable)

Discharge reconnect: 12.6V(defaul,adjustable)

USB output: 5V/3A

Self-consume: <10mA

Operating temperature: -35~+60 degree



Features:

12V/24V auto work

LCD screen display

Two USB output

Easy operation interface

PWM charging mode

short-circuit protection

Battery reverse discharge protection

Battery reverse polarity protection

open-circuit protection

Overload protection



Warm Tips:

1. Always connect the battery before connect the solar panel, disconnect in reverse order.

2. Make sure your battery has enough voltage for the controller to recognize the battery voltage

3.DO NOT connect any inverters, generator or battery charger into the charge controller. If an inverter is to be connected to the system, connect the inverter directly to the battery.



Package:



1.1X 40A Solar Charge Contorller

2.1X English User Manual

• 40A Solar Charge Controller 12V / 24V Auto work; Max input voltage: 40V; Max PV power 400W /in 12V, 900W / in 24V. With Dual 5V / 2A max.
• Solar Charge Controller 20 amps only suitable for lead acid batteries: OPEN, AGM, GEL and Seal, not for nickel hydride, lithium, Liions, or other batteries.
• Three Load work mode (Settable), 【1-15H】and 【0H】both belong to the light control mode, and the load will turned off at dawn. 【24H】Load output 24 hours (except for battery under voltage) 【1-15H】Load on after sunset and closed after setting hours (turn off load after dawn) 【0H】Dusk to dawn (the load will turned off at dawn)
• For protecting the lifespan of your battery, once the voltage of the battery drop below 9V, the solar controller will turn off automatically. Only suitable for small home solar system,
• Charge controller easy to install and operate: Please always connect the battery before connect the solar panel, only suitable for small home solar system.

User questions & answers

Question:	In the lcd display, what is the "mode" information showing? i see b1, b2, or b3 as the options for the mode. what do these values mean
Answer:	Yes this will work I own this mixer I use it for my podcasts it has 2 mic inputs it's a 6 channel mixer. I also use audacity and anchor.fm with this exact mixer. Great quality for the podcast as long as you have a rather decent microphone. I'd say purchase it try it out if it's not for you send it back. Hope this helps
Question:	What is the maximum current (or wattage) available from the load connections on the far right of the controller
Answer:	Hi, yes you can connect the unit to your laptop or computer using the USB port. You may check other details of the unit by visiting our website pyleaudio.com. Type the model number on the search box PMX44T for more details. Thank you.