10 best studio subwoofers

Product description

The single best subwoofer you can get to put a little boom in your room, the Eris Sub8 is the first subwoofer to join the lauded and best-selling Eris studio monitor line. We called it Eris because it’s been designed from the ground up to be part of the family; it compliments the voicing and frequency response of the modern Eris classics The surprisingly loud 100-Watt Eris Sub8 drops down to a molar-rattling 30Hz, allowing you to both rock harder and produce better mixes, as you’ll be hearing an accurate representation of your work. Thanks to robust configuration and I/O, you’ll be able to tailor your Eris Sub8 configuration exactly to your mixing and listening needs. You can connect your existing monitors via ¼” TRS or RCA, set the input level to your liking, and even invert the polarity. Most importantly, you get a High Pass Filter and a Low Pass Crossover control that ensures your Sub8 starts working at the precise low-frequency point where your main monitors stop working. This makes sure you avoid the flubbery, smudged, low-end mess that one hears in redundant, duplicate, redundant bass reproduction that occurs without a crossover. Eris Sub 8 Compact Studio Subwoofer

From the Manufacturer

Eris Sub 8 Compact Studio Subwoofer

• 8-inch, front-firing, paper-composite low-frequency transducer with high-elastisity rubber surround
• Class AB amplifier: 100W peak (50W RMS) power
• Input gain control (-30 dB to +6 dB, continuously variable)
• Continuously variable lowpass filter (50 Hz to 130 Hz)
• Defeatable highpass filter removes frequency content below 80 Hz from the full-range signal sent from the Eris Sub8 outputs to the main speakers
• Left and right, balanced ¼-inch TRS and unbalanced RCA main inputs
• Left and right balanced ¼-inch TRS and unbalanced RCA pass-through outputs for connecting satellite speakers

User questions & answers

Question:	I am a Motivational Speaker, can I use these with a microphone when speaking to an audience of 75 people
Answer:	I know this is too late, but this was an easy install in my Jeep using the factory stereo. It was an awesome addition to the Jeep, and is certainly a whole lot louder than a 6x9. Plus, you can tuck it under the seat or in the back in the rear tray. It wastes virtually no usable real estate.
Question:	Hola, quisiera si al comprar el E3.5 (Pair) si son los dos monitores o solo uno
Answer:	Good deep base.... although if I crank up the base on the device and adjust the radio in the car I get a little thumping.
Question:	Is the the Presonus E3.5 woofer speaker cone unprotected? It appears to have no fabric covering as many speakers would have
Answer:	Yes we have installed many of these under the seat of the Wranglers at our retail stores. It comes with all the wringing you will need. Give us a call if you would like to bundle it with some new Kicker speaker as well. 800-854-5821 M-F 9a-5pm central
Question:	Does this come with all the necessary cords to connect this to a computer? Is it rca trs or xlr
Answer:	It comes with all that. No amp kit needed. Also no need for other extras... It has everything to hook up to your stock or aftermarket system.
Question:	Have a 13 Jeep Wrangler does this connect to the factory stereo without any problems. I have the sub in the back but looking for additional punch
Answer:	I'm using a sundown sae2000. Bumps hard but you could smell the coils burning when I put it too loud.
Question:	Does this unit have good deep bass or more thump
Answer:	There is an expiration date on the box and on each individual wrapper....hope this helps these are ine of the best strips I've used they are reliable and thicker then the rest which makes reading them easier and better
Question:	I have 14' jeep wrangler 2dr. Will this kit fit under the seat? and do I need to get the amp to install this
Answer:	I’ve never seen or heard of that, and I’ve taken way too many pregnancy tests in my life. I’d probably contact the manufacturer if I were you!
Question:	It shows the power cable and fuse does it really come with these wires or will I need an amp kit
Answer:	No, it's just test strips.

Product features

The best subwoofer for Eris monitors.

The Eris Sub8 is the first subwoofer to join the lauded and best-selling Eris studio monitor line. We called it Eris because it’s been designed from the ground up to be part of the family; it compliments the voicing and frequency response of the modern Eris classics. Of course, they’ll play nice with other monitors, too, but if you’ve got a pair of Eris in your home or studio already, the Eris Sub8 is the single best subwoofer you can get to put a little boom in your room.

Maximize your frequency response and accuracy.

The surprisingly loud 100-Watt Eris Sub8 drops down to a molar-rattling 30Hz—a full 50Hz below the Eris 3.5s. This allows you to both rock harder and produce better mixes, as you’ll be hearing an accurate representation of your work. For EDM and hip-hop producers in particular, a sub is a must-have. The Eris Sub8 lets you naturally extend the reach of your Eris E3.5 or E4.5 monitors in a manner appropriate to smaller rooms; exactly where these monitors excel.

Total control and connectivity.

Thanks to robust configuration and I/O, you’ll be able to tailor your Eris Sub8 configuration exactly to your mixing and listening needs. You can connect your existing monitors via ¼” TRS or RCA, set the input level to your liking, and even invert the polarity. Most importantly, you get a High Pass Filter and a Low Pass Crossover control that ensures your Eris Sub8 starts working at the precise low-frequency point where your main monitors stop working. This makes sure you avoid the flubbery, smudged, low-end mess that one hears in redundant, duplicate, redundant bass reproduction that occurs without a crossover.

Accuracy defined.

When you hear the low-frequency foundation of your mix accurately, you can make more informed decisions and create more translatable mixes. You’ll also have more fun.

All work and all play.

While we’ve designed the Sub8 to compliment our smaller-form Eris media reference monitors, we also know that gamers, partiers, and movie buffs alike all enjoy some room-rattle now and again. So rest easy knowing that the Eris Sub8s will upgrade the performance of any powered speaker configuration in a home theatre or gaming rig.

Product description

The CR8S-XBT 8” Creative Reference Multimedia Subwoofer with Bluetooth offers 200W of powerful dedicated bass reinforcement for your studio or home. The sleek design looks great in any room and is the perfect match for any CR Series monitors. Flexible rear panel inputs and outputs include 1/4" TRS and RCA plus easy Bluetooth pairing for effortless streaming. Dial your sound in just right with Input and Output level controls plus a variable crossover and polarity switch. The included CRDV Desktop Volume Control makes controlling your system a breeze. Upgrade your listening experience with Mackie CR8S-XBT 8” subwoofer with Bluetooth .

From the Manufacturer

CR Series CR8S-XBT - 8" Multimedia Subwoofer with Bluetooth®

• Professional studio-quality sound
• 1/4” TRS, RCA, and Bluetooth inputs with 1/4” TRS and RCA outputs
• Adds Bluetooth streaming to any studio monitors
• 200 watts of clean, accurate sound with an 8" woofer
• Desktop remote volume control included

User questions & answers

Question:	Aceptan corriente de 220V
Answer:	I would Like to know to. My remote was DOA I just want to replace the remote and not return the whole unit.
Question:	i connected a 2nd speaker set to the aux of the cr5 but the 2nd set wont work ,but they will if plugged to phones, but cr5 goes mute
Answer:	I have 2 Temblors (1 of which is matched up with the Eris E8 pair. This is one of the best 'balanced' systems I have, and that includes a pair of $8k French studio monitors. Seriously, I highly recommend the Presonus.
Question:	Is the cabinet made of wood or plastic
Answer:	From your interface, using a 1/4" TRS Cable, run your R and L to the sub first. The sub has 2 outputs on it that you can then run 2 more 1/4" TRS cables to your monitors. Basically the audio flows through the sub on its way to your monitors. The Temblor has a crossover built into its outputs, meaning the low freq that the sub covers, will be removed from monitors.
Question:	Hola, El precio es uno o el par
Answer:	I've not experienced auto sleep. I have mine on for hours each day as I work in my office. As far as I can tell it's operating continuously.

Product features

CR-X Series Multimedia Monitors

CR Series Creative Reference Multimedia Monitors offer studio-quality sound with cosmetics that compliment any desk whether you’re making music, creating content, or just relaxing to your favorite tunes. The sleek design of CR-X features a brushed metal panel and a distinct outline that stands out. Available in a vast range of sizes from 3” to 8” with Bluetooth option plus an 8” subwoofer with Bluetooth, CR-X has the perfect match for your needs. Upgrade your listening experience with Mackie CR-X Creative Reference Multimedia Monitors.

Home Studio

Mackie knows studio monitors, and every bit of that experience was poured into the CR-X Series. Excellent sound, affordable, and sleek looks make these perfect for small home recording studios.

Content Creators

Looking to make it big on the internet? You bring the talent, we've got the gear. What better place to start than your audio. An accurate representation of what your videos, podcasts, and more will sound like is crucial to creating great content.

Gaming

CR-X is perfect for desktop gaming when you need to give the headset a break. Crisp highs mean you'll hear every footstep, and balanced lows and mids will keep you immersed in every element and storyline.

Desktop / Bookshelf Speakers

Sometimes it's nice to just relax and hear your favorite music while you sip your favorite drink. One way to make it not so fun is when the sound isn't quite up to par. CR-X brings you closer to your music with full, faithful sound for all music styles.

Sleek Looks

Brushed metal faceplate, textured cabinet, and classic CR green will upgrade the look of any desk.

Flexible Connections

Standard models are equipped with 1/4" balanced/unbalanced and RCA, and 1/8" Aux inputs. Bluetooth models allow for easy wireless streaming. (See model details for specific input availability)

Front Panel Control

With the volume/power knob on the front panel, you can easily dial in the perfect level.

Connect Your Headphones

Need to listen even closer? CR-X monitors have a headphone output built-in and it's right there on the front panel. Plugging in headphones will also automagically mute the speaker output.

Product description

You're not monitoring without a sub are you? It's the 21st century for crying out loud! Gone are the days of wimpy, baseless tracks! Modern music needs - nay, demands - bass, and without a sub how are you to know if you have the right amount of low-end "oomph! "? Jbl LSR310S Powered sub is your affordable powered sub solution - not to mention being the perfect companion piece to your Lsr300 series monitors (but it'll work with virtually any system). The JBL LSR310S reaches all the way down to 27Hz, so there's no doubt it'll faithfully reproduce the lowest lows, making sure you always have a clear picture of the bass in your tracks. Beef up your studio playback with the 200-watt, powered JBL LSR310S subwoofer.

• Jbl patented slip stream port This patented JBL port design works in concert with the LSR310S Low frequency driver for Deep, dynamic Bass Response at all playback levels
• Xlf extended low frequency setting JBL first, the xlf setting Activates a specially-engineered tuning that emulates the ample bass tuning used in today's dance clubs
• The custom-designed driver in the LSR310S delivers deep low frequency response into the 20 Hz region, and 113 dB peak output, for long periods at full rated power with no risk of failure
• Professional balanced inputs and outputs with balanced XLR and 1/4-inch inputs and XLR outputs you can add the LSR310S to any Studio monitor system to extend its low frequency performance
• The -10Dbv/+4 dB sensitivity switch ensures compatibility with a broad range of signal sources, allowing you to connect the LSR310S to high-output professional equipment without any danger of input overload. Maximum peak input level: +20. 3 dB
• Purchase includes: studio monitor, power cable, and set-up guide
• Inputs: balanced XLR (x2) and TRS (x2)

User questions & answers

Question:	Are xlr outputs high-pass filtered when the sub's crossover switch is set to 80hz? if so, what is cutoff frequency of xlr outputs
Answer:	Hello, When using the crossover at 80Hz, it would apply a high pass filter to your monitors from 80Hz. It would also engage a low pass filter on the sub from anything above 80Hz. If this was helpful, please consider purchasing from us (pixelproaudio on Amazon). We can help with support after the sale as well. We have it in stock and ready to ship. - Pixel Pro Audio
Question:	If I use the TRS input, will I be able to use the XLR output
Answer:	Yes, you can use the balanced Tip-Ring-Sleeve 1/4" input (that might come from your preamp) with the balanced XLR (microphone-type) output to your satellite speakers. Shouldn't be any issues unless one of your cables have a pin wired in conflict. This is exactly how I have it configured using a Duet 2 and LSR-308s.
Question:	Does it come w/ the 2 xlr or trs cables it needs
Answer:	No cables included with my unit. I recommend Mogami.
Question:	Am I correct in my thinking that you connect the sub to your audio interface, and then your studio monitors will connect from the sub
Answer:	Yes but not necessarily, with the right connection wires it can be run from any type of input. I run a 1/8" to two 1/4" (L & R) into the sub and two female XLRs to 1/4" cables into my monitors. Sounds amazing.

Product features

JBL LSR310S

Extend your system LF all the way down! The LSR310S subwoofer incorporates JBL’s patented Slip Stream Port working in concert with a custom 10" down-firing driver and a 200 Watt amplifier to add deep, powerful bass to any studio monitor system. A JBL first, the XLF Extended Low Frequency setting lets you hear your tracks with the augmented bass tuning used in today’s dance clubs.

JBL Patented Slip Stream Port

This patented JBL port design works in concert with the LSR310S low frequency driver for deep, dynamic bass response at all playback levels. The double-flared shape of the port is precisely calculated to optimize low-frequency extension.

Custom 10" Down-Firing High Excursion Low Frequency Driver

JBL Transducers are legendary for their performance. The custom-designed driver in the LSR310S exemplifies JBL engineering prowess, delivering deep low frequency response into the 20 Hz region, and 113 dB peak output, for long periods at full rated power with no risk of failure.

XLF Extended Low Frequency

A JBL first, the XLF setting activates a specially-engineered tuning that emulates the ample bass tuning used in today's dance clubs. When producing a dance track, the XLF setting will inspire you and bring a bit of the club to your control from. For inspiration to the max, position the LSR310S in the nearest corner of your room and activate the XLF setting.

Product description

8inch Powered Subwoofer

• 8inch bass-reflex powered subwoofer
• 22Hz - 150Hz frequency response
• High-power 150W amplifier 
• LOW CUT switch, LOW CUT control (80-120Hz) HIGH CUT control (80-120 Hz)
• PHASE switch 

User questions & answers

Question:	is this the same as the hs8s
Answer:	Yes, amazon just lists it as HS8 Studio which is what the S stands for.
Question:	Why does it say lithium ion battery required on the hs8s
Answer:	Hello. This was installed by a professional installer so I can't answer your question. I don't believe we needed a battery and I certainly haven't replaced one. Sorry I can't be of more help.
Question:	does it support 240v? I will mainly use this in Hong Kong
Answer:	I have it on 240 V in Europe. But always check the specs, not sure if there are different models.
Question:	Does this need its own channel on an audio interface, or does it get audio through the speakers
Answer:	it does not need it own channel you can hook your powered studio speakers XLR inputs into the back of this subwoofer

Product features

Yamaha HS Series Monitors

Ever since the 1970's the iconic white woofer and signature sound of Yamaha's nearfield reference monitors have become a genuine industry standard for a reason - their accuracy. Unlike studio monitors with added bass or treble frequencies which may sound more flattering at first, HS Series speakers were designed to give you the most honest, precise reference possible, providing an ideal sonic platform to build on throughout the mixing process.

By combining acquired knowledge and expertise with state-of-the-art sound technologies, Yamaha's speaker engineering team have examined, then optimized, every aspect that has contributed to making these monitors the most trusted in the business. The second generation HS Series also adds a new 6.5" model to the lineup, bringing its exceptional accuracy to an even greater variety of recording environments.

Newly Developed Transducers

The HS Series features newly developed transducers that achieve astonishingly smooth response over a wide range of bandwidth. These transducers utilize an advanced magnetic field design that regulates the flow of magnetic response to provide seamless, natural sonic transitions.

High Performance Amp Unit

HS Series speakers employ an amplifier unit perfectly matched to the transducers utilized in each model of the series. Featuring a bi-amp design with a separate dedicated amp for both the woofer and the tweeter, this amplifier unit ensures that each HS Series speaker consistently delivers high-resolution sound with exceptionally flat response across the sound spectrum.

Controls and Connectivity

HS Series full-range models feature two response controls with detailed settings that allow them to adapt to the surface acoustics of rooms of varying shape and size. For inputs, HS full-range speakers can accommodate a wide range of balanced and unbalanced sources such as mixers, keyboards and audio interfaces with XLR and TRS phone jacks.

Low Resonance Enclosure Design

HS Series cabinets are designed to eliminate unwanted resonance and increase the accuracy of sound reproduction to their extreme limit. The enclosures are constructed from a very dense and resilient MDF with a damped acoustic response that is perfectly suited for reference monitors.

Cutting Edge Noise Reduction

Speaker port design can greatly influence the clarity of overall sound. Often a vortex at the either end of the port can generate air vibrations inside of the port, causing unwanted noise. By adopting an advanced noise reduction technology that incorporates a thorough analysis of a visual representation of the sound, Yamaha's engineers are able to control and reduce the vortex.

New HS Install Versions

The new installation version of the renown Yamaha HS Studio Monitors include mounting points and screws for installation. Compatible with wall, ceiling, and baton brackets (sold separately.

Product description

Nothing brings realism to recorded sound like deep, authoritative bass. Yet, most affordable systems are compromised in this critical region. For the sub1010, the rich, powerful bottom octaves are fundamental—literally—to the life of music and movie soundtracks when it comes to reproducing the full spectrum of instruments and sound effects.

• Enclosure Type: bass reflex
• Amplifier Type: Class AB
• Amplifier power: 120 watts peak/ 60 watts RMS
• Frequency response: 38hz-200hz; crossover frequency: 40hz-200hz
• Driver: 10" Low Throw dynamic woofer with these inputs: L/R/LFE/speaker level

User questions & answers

Question:	Why did the price go back up to $129. ? I was going to purchase it at $99. , I wont pay
Answer:	There are fairly clear instruction included with the unit. If you have a receiver with subwoofer out, just run an RCA cable to the single input on the subwoofer. If you are using just a stereo amplifier, then you'll need to do some additional wiring. Again, the instructions should be clear enough, but basically, wire from the amp outs to the subwoofer and then from your subwoofer to your speakers, and then set the crossover frequency using the subwoofer dial.
Question:	This subwoofer has hi level ins but no hi level outs in the pictures. How does that work? Run 2 sets of wire from amp? 1 set to sub 1 set to speakers
Answer:	Yes it is powered. 400 watts, is plenty of power. Excellent sound. Keep it away from the wall a foot or so so it can breathe.
Question:	Does unit have a lfe connection? i don’t see one from the pics
Answer:	I adjust as needed, depending on the source. Normally people set it in the middle and use the source (receiver, etc) for adjustment, but my new receiver requires the TV to be on to adjust sound output
Question:	Hi ,My question is how do i set up my subwoofer
Answer:	Hi,I know it's been almost a year since you purchased the sub. Don't use any petroleum based product on the rubber surround. It will dry out the rubber. Btw, the rubber will hold up for many years and even longer if you keep sunlight off of it. It being a sub the grill won't harm the sound the way a grill can slightly harm on your main speakers. Steve

• Rockville APM10W 10" 400 Watt Active Studio Subwoofer in White. 200 Watt RMS. Built-in Class D Amplifier. Enclosure is made of top quality MDF wood. Our enclosure is not particleboard it is true high-grade MDF!
• The enclosure is 0.7" thick while the front board of it is a full 1.34" thickness to give you the ultimate best sound quality! Comes in 3 enclosure finish options Wood finish painted black. Wood finish painted white. Wood finish with vinyl front board
• Class "D" Amplifier Circuitry with Auto-Switching Power Supply. LED Power on/Stand-by Indicator on Rear Panel. Rubber woofer surrounds increases sound quality and eliminates unwanted distortions.
• We developed the Most Optimized Magnet structure, Cone, and Cabinet Space that Reproduces the Sound to Play Back Exactly the Way it was Recorded! Specially Wound Voice Coils Produce Accurate Response along the Low Frequency Spectrum.
• Thick "Wadding" protects inside the subwoofer cabinet - Wadding is a white, artificial silk-like material that we put inside the subwoofer cabinet for multiple reasons.
• Every subwoofer in Production Undergoes a Computer Generated Sound Check Test to Ensure it Upholds to our Specifications and Standards. We use a "6Sigma" style Quality Assurance of Each Product.
• Inputs / Outputs / Controls: Volume control.Crossover Frequency Control allows you to adjust low frequency input: 50Hz - 150Hz.1/4" TRS input jack.Left and Right XLR input/outputs.RCA input/outputs.

User questions & answers

Question:	Can I play music from my itouch on these
Answer:	I have not used it on 12 very but it's an electric heating element so I'm sure it uses many amperage. I'm having problems that when it gets cold it starts overheating and then bringing the inside temperature down
Question:	Are these actually 30Hz - 20 kHz
Answer:	yes, it runs on all three types but will run on dc 12 volt only if you want it to
Question:	How do you connect this to a av receiver
Answer:	R.E. Bradley,We find they taste much better than regular lollipops (and they're healthy too). They can be tart depending on the flavor you pick.
Question:	i have rockville amp6c 6.5'' 2way 350w monitor speakers, will THIS CONNECT TO THEM? HOW TO CONNECT
Answer:	High fructose corn syrup comes from corn crops that have a high incidence of genetically modified organisms and use of pesticides. Research “Seeds of Change”. I can not make this stuff up.

• 8-inch, downward-firing, glass-composite low-frequency transducer with high-density rubber surround
• Class AB amplifier: 200W peak (100W RMS) power
• Input gain control (-30 dB to +6 dB, continuously variable)
• Continuously variable lowpass filter (50 Hz to 130 Hz)
• Defeatable high pass filter removes frequency content below 80 Hz from the full-range signal sent from the T8 outputs to the main speakers
• Protection features: RF interference, output-current limiting, over-temperature, turn-on/off transient protection, subsonic filter, external mains fuse

User questions & answers

Question:	Should i buy this or a elac debut s10? (in combination with two eris 44) thank you
Answer:	It is suitable for sleeping. And it is not easy to slip out of the ear canal because the design
Question:	I just bought the e5 studio monitors and have the Presonus basic interface with 2 outputs. How does the sub hook up to either monitors or interface
Answer:	Use the damping to adjust the volume, simply slide up and down to adjust
Question:	Is there any way to keep this sub from auto-sleep mode when playing music at low levels? It keeps shutting off and it's really annoying
Answer:	If you use it in vehicle or boat,yes.
Question:	If i were to connect my monitors through the trs ins/outs, will the temblor t8 allow for signal pass-through even when the sub itself is turned off
Answer:	About 20 lb gas tank will be ok.

• Immersive sound – 5 speakers produce powerful bass, dynamic midrange, and crisp highs. Dolby Atmos technology adds space, clarity, and depth.
• Ready to help - Ask Alexa to play music, read the news, and answer questions.
• Voice control your music - Stream songs from Amazon Music, Apple Music, Spotify, Pandora, Tidal, and more. With Amazon Music HD, listen to 70 million songs in the highest quality audio formats available: HD, Ultra HD, and 3D formats like Dolby Atmos.
• Adapts to any room - Automatically senses the acoustics of your space, fine-tuning playback for optimal sound.
• Built-in smart home hub - Ask Alexa to control Zigbee-compatible devices.
• Keep your family in sync - Use your Alexa devices like an intercom and talk to any room in the house with Drop In and Announcements.
• Designed to protect your privacy - Built with multiple layers of privacy controls, including a microphone off button that electronically disconnects the mics.

Product description

This is an 8-Inch powered subwoofer capable of producing 60 watts (RMS) output. The subwoofer has a frequency response range of 50 to 250 Hz with a lowpass crossover filter, which can be adjusted from 50 to 150 Hz. Gain and frequency knobs on the control panel allow you to adjust the crossover filter and the power output for the optimum blend and balance of bass output with your stereo or surround speakers. The subwoofer has multiple input options, which allow it to be used with any existing stereo or 5.1 (or greater) amplifier system. For each input there is a corresponding output. High-level inputs accept a full-range signal from the amplifier's stereo speaker outputs. When connecting the unit as part of a 5.1 system, these would be taken off the Front Left and Front Right outputs in parallel to the standard pair of front speakers. The subwoofer provides its own power and includes impedance matching circuitry, so this will not reduce the power output to the front speakers or affect the overall impedance load on the amplifier. Additionally, the subwoofer has a set of right/left Line Level inputs. If using a standard stereo system, without a special subwoofer output, you can connect these to the left and right line level outputs on the amp. The subwoofer will then combine the signals to process the mono bass signal it needs to drive the speaker. If you are using an amplifier with a single mono subwoofer line level output, simply use an RCA -Inch-Inch cable to split the output and send it to the two line level inputs on the subwoofer. The subwoofer is housed in an attractive black wood cabinet that measures 13.75-Inch x 11.75-Inch x 11.75-Inch (H x W x D). The driver and a 2 3/4-Inch sound port are located on the front, covered by a black cloth speaker grill. Amplifier Power Output: 60 Watts (RMS).

• This is an 8" powered subwoofer capable of producing 60 watts (RMS) output. The subwoofer has a frequency response range of 50 to 250 Hz with a lowpass crossover filter, which can be adjusted from 50 to 150 Hz. Gain and frequency knobs on the control panel allow you to adjust the crossover filter and the power output for the optimum blend and balance of bass output with your stereo or surround speakers.
• The subwoofer has multiple input options, which allow it to be used with any existing stereo or 5.1 (or greater) amplifier system. For each input there is a corresponding output.
• High-level inputs accept a full-range signal from the amplifier's stereo speaker outputs. When connecting the unit as part of a 5.1 system, these would be taken off the Front Left and Front Right outputs in parallel to the standard pair of front speakers. The subwoofer provides its own power and includes impedance matching circuitry, so this will not reduce the power output to the front speakers or affect the overall impedance load on the amplifier.
• Additionally, the subwoofer has a set of right/left Line Level inputs. If using a standard stereo system, without a special subwoofer output, you can connect these to the left and right line level outputs on the amp. The subwoofer will then combine the signals to process the mono bass signal it needs to drive the speaker. If you are using an amplifier with a single mono subwoofer line level output, simply use an RCA "Y" cable to split the output and send it to the two line level inputs on the subwoofer.
• The subwoofer is housed in an attractive black wood cabinet that measures 13.75" x 11.75" x 11.75" (H x W x D). The driver and a 2 3/4" sound port are located on the front, covered by a black cloth speaker grill.

User questions & answers

Question:	What is the return policy
Answer:	You can go through Monoprice- their customer service is incredible
Question:	What are the dimensions of the cabinet? description says 13.75-inch x 11.75-inch x 11.75-inch (h x w x d). info says 14.8 x 16.1 x
Answer:	11 7/8" wide 13" tall with feet attached 11 3/4" deep BUT add 1/2" for the connections that stick out the pack, perhaps a bit more to allow for the cables to plug in.
Question:	How tall is it without the feet, are the feet removable
Answer:	feet are removable and height without feet is 11 and 13/16ths
Question:	I only have 1 3.5mm out to subwoofer. if a use a 3.5mm to rca cable will it work ok
Answer:	Use a 3,5mm to 'Y' RCA cable (adapter). JSAUX makes a good one, I use it from my ZVOX to subwoofer. JSAUX RCA Cable, [6.6ft/2M, Dual Shielded Gold-Plated] 3.5mm Male to 2RCA Male Stereo Audio Adapter If you need more length just get a male-to-female 3.5mm extender/headphone cable.

Product features

About Us

We exist to bring simplicity, fairness, & confidence to technology choices.

Established in 2002, we have built a stellar reputation for product excellence. We offer over 7,000 high-quality, electronics and accessories to professionals and consumers worldwide. Our proven business model eliminates entire layers of markup within the supply chain, which allows us to sell premium products.

Product description

The IsoAcoustics ISO-200Sub Acoustic Isolation Stand is designed for subwoofers used in professional studios, project studios, Hi-Fi and home theater settings. The ISO Stands are an updated version of the popular ISO-L8R series and features a lower profile, new frame design and a newer version of isolator for improved performance. The ISO-200Sub isolation stand is 7.8-Inch (200mm) wide x 10-Inch (255mm) depth x 3.5-Inch (90mm) height and is rated for subwoofers weighing up to 75lbs. The ISO-200Sub does not include height or tilt adjustment.

Experience more Punch and Clarity

The ISO-200Sub is designed to clean up acoustic issues common with subwoofers. The ISO-200Sub allows the subwoofer to float and controls the energy of the subwoofer to prevent the low frequencies from being driven into the supporting surface. As a result you will hear more punch and clarity from your subwoofer.

Advanced Technology

The ISO-200Sub features the same patented technology as the entire family of award-winning IsoAcoustics Acoustic Isolation Stands.

Enhance your Listening Experience

The isolators manage the energy of the speaker to reduce vibrations resonating through the supporting surface to eliminate dissonant sounds in the listening area or joining rooms.

Compatibility

ISO-200Sub is designed to accommodate most subwoofers, and can be used as a single unit, or combined with additional units for larger subwoofers.

• 7.8” (200mm) Wide x 10” (254mm) Depth 3.5” (90mm) Height. 75lbs weight capacity. Package includes 1 Stand.
• PATENTED ISOACOUSTICS ISOLATION: Tested at the National Research Council of Canada (NRC). The IsoAcoustics award winning design provides superior isolation performance.
• EXCITING THE SUPPORTING SURFACE: The isolators manage the energy of the speaker to reduce vibrations resonating through the supporting surface to eliminate dissonant sounds in the listening area or adjoining rooms.
• REDUCES INTERNAL REFLECTIONS: IsoAcoustics isolator reduces internal reflections to eliminate smear. The result is an improved stereo image of natural spatial sound.
• COMPATIBILITY: ISO-200Sub is designed to accommodate most subwoofers, and can be used as a single unit, or combined with additional units for larger subwoofers.

User questions & answers

Question:	i have a focal sub6 (11" sub) .. can i use this with that
Answer:	Grout Pen does not require you to seal the grout after the pen is used. Also note that if grout is already sealed this will likely prevent Grout Pen (or anything else) from adhering to the grout. SIMPLE SOLUTION: Skip scrubbing tiles and use a grout pen to clean, whiten, and recolor your grout USE ANYWHERE: Ideal for the bathroom, kitchen, and any other room that has floor or ceiling tiles LONG LASTING INK: Tackle small or large DIY projects with a pen that covers up to 60 meters of grout RICH PIGMENTS: Grout paint markers available in 11 different colors with reversible 5mm or 15mm nibs ADVANCED FORMULA: Non-toxic, water-based ink that helps protect against dark spots and stains
Question:	will it fit a cabasse sub 13" X
Answer:	I held onto a paper towel and wiped it off the tile as I went, but don’t worry. I’m pretty sure it will come off the tile even after it’s dry. You just may have to scrub it off. Wipe as you go for the rest of your project. It’ll be easier.
Question:	will they hold a 12 inch klipsch sub
Answer:	Grout Pen is a paint marker specifically for grout. You would need to fill in any cracks or gap in the grout first, and then go over it with Grout Pen for a new clean appearance. SIMPLE SOLUTION: Skip scrubbing tiles and use a grout pen to clean, whiten, and recolor your grout USE ANYWHERE: Ideal for the bathroom, kitchen, and any other room that has floor or ceiling tiles LONG LASTING INK: Tackle small or large DIY projects with a pen that covers up to 40 meters of grout RICH PIGMENTS: Grout paint markers available in 11 different colors with reversible 5mm or 15mm nibs ADVANCED FORMULA: Non-toxic, water-based ink that helps protect against dark spots and stains
Question:	Would like legs 2 to 3 inches longer. Why are they not offered? Seems that the subwoffer would perform as good or even better if higher
Answer:	That depends on how much area you want to lighten. Grout pens are amazing for how well they work and how long the paint stays in tact. This "light" grey is darker than I expected, so it might not be exactly what you are looking for to lighten dark grey. I had a couple of stained areas I was "fixing" at my house and went over the spot with 2 colors and blended them with a damp cloth. It worked great. Good luck to you.