14 best milling tools

• Carbide Indexable End mills, R8 shank, 2'' TPG32
• Comes with inserts installed
• Uses standard triangular inserts
• Positive rake 90° right-hand cut
• R8 Bridgeport thread: 7/16" - 20

User questions & answers

Question:	Can this be used to cut hard woods witthout burning the wood
Answer:	As others have have stated it really depends on a lot of things, this is however more of a face mill it's not intended to take deep fast cuts, if you need to go deep use a conventional roughing end mill and use this for your final passes to get a nice clean finish. I've used mine on titanium and 7075 aluminum and it has produced a very nice smooth finish on the material.
Question:	How many thousandths cut (per pass) can one take when using this tool on various metals
Answer:	Look up ‘speeds and feeds’. Google that phrase, you’ll find what you need. Varies greatly with what you’re cutting, depth of cut, lubrication, rigidity of machine and workholding.
Question:	What rpms have people been running this at? i have found suggestions on pm ranging from 250, to 2200... makes no sense
Answer:	This is Standard R8 Shank ( Bridgeport Shank); which means the smaller end is 0.949" and larger end if is 1.25"; Shank length is 4"; drawbar thread is 7/16-20. Thanks.
Question:	What is the shank diameter
Answer:	My first answer is 7/16 in. I have a set of Irwin tap chucks that grab the square shank .. another brand of tap has a 3/8 inch .. perhaps a small crescent wrench

Product features

AccusizeTools Carbide Indexable End Mill, R8 Shank, with TPG Inserts

• Carbide Indexable End Mills
• R8 Shank
• Carbide Inserts: TPG
• Comes with inserts installed
• Uses standard triangular inserts
• Positive rake 90° right-hand cut
• R8 Shank Threading: 7/16" - 20

SKU: 0046-0915

• Cutting Diameter: 1"
• No. of Inserts: 2
• Insert: TPG22
• Locking Screw: SM5 x 10

SKU: 0046-0916

• Cutting Diameter: 2"
• No. of Inserts: 3
• Insert: TPG32(TPGN1603)
• Locking Screw: SM6 x 12

SKU: 0046-0917

• Cutting Diameter: 3"
• No. of Inserts: 5
• Insert: TPG32(TPGN1603)
• Locking Screw: SM6 x 12

Cutting Speed for Low-carbon Steel, High-carbon Steel, Alloy Steel, and Tool Steel

Product description

Set 8 Pcs Dp16 No1 :Z12~13; No2 :Z14~16; No3 :Z17~20; No4 :Z21~25; No5 :Z26~34; No6 :Z35~54; No7 :Z55~134; No8 :≥135

• Set 8 Pcs Dp16 ：pressure angle: 14.5 degree
• Set 8 Pcs Dp16 ： Outside Dia: 55mm
• Set 8 Pcs Dp16 ：inner Bore: 22mm
• R8 shank gear cutter holder fitting for hole 22mm gear cutter
• R8 shank gear cutter threaded 7/16(Inch)

User questions & answers

Question:	Is this module
Answer:	I believe so, definitely not carbide. They work well just keep them lubricated and don't get over jealous. I've just started learning to cut gears and my first attempt came out very well.
Question:	Are the cutters HSS
Answer:	If the drill chuck is mounted in an R8 spindle. Pop the chuck out and chuck this up. Else, no. Plus how are you rotating the gear? How are you moving it across the cutter with any precision? You normally need an indexer and a mill table, or possibly a mill/drill with a moving table. I have good results with this set but I use a Bridgeport and an indexer.
Question:	Can I stick this in a drill press? For a small gear
Answer:	MAX RPM is 35000 Recommend 25000

Product description

Mitutoyo Edge Finder, Shank Dia: 3/8", Tip Dia: .200".

• Used in a milling machine to find the workpiece edge
• All working surfaces are hardened and ground

User questions & answers

Question:	Can you tell me this item 050101 had Mitutoyo stamp on it or not? And how do you know where it made from? I saw on pic show nothing on there
Answer:	Safe? It only has to spin 60 RPM's. You push the unit over off center to start, then move the machine over until it centers itself. This isn't a milling cutter.
Question:	What is the safe max RPM rating for this edge finder
Answer:	its .200 on the small end,.400 on the large. you use it by chucking up the larger end into either a collet or drill chuck,turn on the spindle and touch it to the edge of the workpiece until the wobble or runout runs true,then zero out your readouts or set dial to zero,then move negitive .100 which is half of .200 and that puts the spindle dead on the edge of the workpiece,then you can calculate any machining off of that
Question:	Is it adjustable? Does it have something on the upper end to tighten it
Answer:	don't worry it's slowly self-correcting: now it's 12 each or 75 for 2. Come back in 2029 and the amazon AI will have achieved perfect homeostasis.
Question:	Why is one listed for $11 and two pack $75? Am I missing something or was that a typo
Answer:	Yes, with the correct RPM

• high speed steel, Tin Coating. Straight Shank
• One of each size in both 2 & 4 flute: with 3/8'' shank:3/16'', 1/4'', 5/16'', 3/8'', 7/16''
• With 1/2'' shank: 1/2'',9/16''
• With 5/8'' shank: 5/8'',11/16''
• With 3/4'' shank: 3/4''

User questions & answers

Question:	What is the cutting depth on these
Answer:	Yes, with good quality.
Question:	are the end mills made in China
Answer:	This end mills works very well on regular steel, cast iron, etc. for the Pistols maybe you could try the 1102- series, such as 1104-0038, 1102-0012, 1102-0120, 1102-0058, 1102-0034 or 1104-0038, 1104-0012, 1104-0120, 1104-0058, 1104-0034, you can find them all on amazon.com, Thank you.
Question:	Will these cut metal as in pistols upper sliders? Not alum but metal
Answer:	Yes, I have used it on aluminum.

Product features

20pcs TiN Coated H.S.S. End Mill, #1810-0100

Features

• 2-flute end mills are for machining aluminum and wood.
• 4-flute end mills are for machining steel.
• TiN Coated.
• H.S.S.
• 20 Pcs/Set.
• Straight Shank.
• Inch Size.
• 10 pcs 4 Flutes End Mill & 10 pcs 2 Flutes End Mill.

One of each size in both 2-flute & 4-flute:

• With 3/8" shank: 3/16", 1/4", 5/16", 3/8" and 7/16"
• With 1/2" shank: 1/2" and 9/16"
• With 5/8" shank: 5/8" and 11/16"
• With 3/4" shank: 3/4"

Product description

Each Fly Cutter is supplied with black oxide finish, a setscrew flat and a blank high speed steel tool. 1/2-Inch shanks. 3/4-Inch, 1-1/8-Inch and 1-3/8-Inch head sizes. 3/16-Inch, 1/4-Inch and 5/16-Inch bit sizes. Stand Included.

• Head Sizes: 3/4-Inch, 1-1/8-Inch and 1-3/8-Inch
• 1/2-Inch Shank
• Bit sizes: 3/16-Inch, 1/4-Inch and 5/16-Inch
• Black oxide finish
• Set screws and blank hss tools included

User questions & answers

Question:	Can they bore cast iron
Answer:	Determine the diameter and depth of cut, then do a search on the web, there are many good feed and speed charts available
Question:	what would be a good RPM to run at for aluminium
Answer:	I have used these fly cutter in my mill up to 1500 rpm. Good cutting around 900 rpm for aluminum. slower for steel.
Question:	What is the maximum RPM for these cutters
Answer:	With the stock bit it's about 70mm on the large cutter. But with a larger bit I'm cutting 120mm (5") on wood. Would not recommend very large diameters for metal.
Question:	whats largest diameter cut of this set
Answer:	no I.D. on the edge finder. case has mitutoyo america sticker on it. works fine no problem with it.

• Diameter: 1/2'', Shank Diameter: 1/2'', Flute length: 1-1/4'', Overall Length: 3-1/4'', 4 Flute, Coarse Tooth
• TiAlN Coated, Center cutting, M42-8% Premium cobalt, Flutes ground by a world-class IS-9002 Factory, CNC Qualified
• Produces a smooth finish that often eliminates the need for a finishing cut for profiling and shallow slots.
• Used for aggressive machining. Performance approaching solid carbide with tough H.S.S Tools. Recommended for abrasive materials.
• Excellent performance in hard materials that are difficult to cut. Extremely hard, wear resistant.

User questions & answers

Question:	How does this cut in wood
Answer:	Sorry, I cannot find my .75 mill right now. However, it doesn't really matter. The grooves will cause the cut material to be a little oversize because it will not be removed between the points. But not nearly as much oversize as the groove depth, because the points and grooves on each flute do not align with the other flutes. In other words, what one flute doesn't remove, another will, so the finish will be a lot smoother than the screw-like threads of the tool. If you want more removed than that, you will need to measure your part and make another cutting pass with either the same roughing mill or a plain finish mill. On parts I have made, I purposely left the ripple finish from the roughing mill because I think it is pretty.
Question:	assuming the OD diamiter of the tool is .75, what is the dimension of the inner grooves of the serrated feature
Answer:	made in China, very good quality. Thanks
Question:	Where are these made
Answer:	It is a center cutting end mill just like a two flute end mill.
Question:	Is this cutter a center cutting end mill
Answer:	I purchased the listed fly cutter set some time back. Your question about boring cast iron is an easy answer. Yes. I have sharpened the HSS cutters to the proper angles and this will easily cut cast iron. Cast iron machines easily due to its molecular makeup. You can use cutting oil but none is needed. I have had no trouble machining cast iron with these cutters. Go make some chips.

Product features

Roughing End Mills, Side Milling[1/4"‐1"] Recommended Cutting Conditions

• High grip strength, impact resistance and strong, clear speed advantage in cutting off a large margin and processing.
• To maintain tight tolerances unmatched performance.
• Practical and a variety of processing environments, even in very dirty environments, such as cast iron also has good features.
• User clamping and convenient way to replace, only a wrench to complete the replacement of the cutter blade and pad.
• Accessories steel is good, long life, reducing the user cost of the tool.

User questions & answers

Question:	Can this be used on aluminum
Answer:	No, too big.
Question:	Will it fit in a mini lathe
Answer:	They take any other APKT11T3 inserts, such as 0056-1130 APKT 11T308 PM Carbide Insert, BPG20B PVD Coating for cutting steel; and 0058-1130 APKT 11T308LH Carbide Insert, YD101 Coating for cutting Aluminum; or 1056-1135 APKT1135PDER-M2/H2, Cutting Stainless Steel; you can find them all on Amazon.com. Thank you.

Product features

Features:

High grip strength, impact resistance and strong, clear speed advantage in cutting off a large margin and processing.

To maintain tight tolerances unmatched performance.

Features:

Practical and a variety of processing environments, even in very dirty environments, such as cast iron also has good features.

User clamping and convenient way to replace, only a wrench to complete the replacement of the cutter blade and pad.

Features:

Accessories steel is good, long life, reducing the user cost of the tool. Suitable for simple steel processing.

Product description

Voltage: 110V (US Plug)



Input Power: 800W



No Load Speed: 30000rpm



Frequency: 50 / 60Hz



Collet Diameter: 6.35mm(1/4")



Power Cord Length: about 4.4 ft



Machine weight: 3 lbs



Package weight: 5 lbs



Package includes

1x 110V Palm Router

1 x Router Bit

1 x Straight Guide

1 x Guide plate

1 x Trimming Guide

2 x Wrenches

1 x Bolt

1 x Screw

1 x Manual



15PCS 1/4" Shank Router Bits Set:

R6.35mm Cove Box Bit

R6.35mm Bearing Cove Box Bit

6mm Panel Pilot Bit

12.7mm Dovetail Bit

12.7mm Bearing Flute Trim Bit

R3.17mm Cove Box Bit

12.7mm 45° Chamfer bit

12.7mm 45° Grooving bit

R9.5mm Rounding Over Bit

12.7mm 90° V Grooving bit

R4mm Roman Ogee Bit

5mm/6mm/12mm/16mm Straight bits



features

Transparent base design makes the operation process visible and it is easy to control.



Comfort handle ergonomic design.you can operate it easily.



Trimming guide, roller running along the curve, ensuring cutting is exact, curve processing is fine.



Machine comes with a 15pcs bits which can meet almost all daily needs of woodworking.If you are a beginner who are looking for a palm router set for practicing, it would be your perfect and smart choice.



Widely used in wood processing, handicraft producing, plastic sheeting, wood veneer and other similar materials chamfering, grooving, surface finishing, curve cutting, planning wood edge, pattern processing operations activities and DIY.

• Powerful motor 800W power for a variety of routing and trimming applications.Transparent base design makes the operation process visible and it is easy to control.
• Edge guide and roller guide makes the straight trimming easier and faster.Smooth rack-and-pinion depth adjustment system ensures precise operation for a range of cabinetry and woodworking applications.
• Ergonomic handle grip.Rubber covered handle for comfortable grip and anti-fatigue long term operation.The durable aluminum body chassis and base is waterproof and dust proof with better heat resistance performance.Exquisite steel chuck for stable and fast bits changing.Spiral vent on the top for high efficiency heat diffusion ensures the machine has a longer running time.
• Universal carbon brush is easy to replace.The knife scale can be adjusted precisely by lifting the knob refer to the scale printed on the machine so that the cutting is exact,curve processing is fine.Widely used in wood trimming, grooving and drilling.
• Package includes 800W compact router tool with 5ft cord, 15 router bits, edge guide, roller guide, guide plate,wrenches, bolt, screw, replacement carbon brushes, manual.

Product description

Specification

Blade Material: Industrial Grade Micro Grain Carbide

Body Material: Carbide Tipped

Shank Diameter: 1/4"(6.35mm)

Cutting Length : 13/16"(20.6mm)

Cutting Head Size: 1-1/16" wide x 5/16" high

Cutting Shaft Size: 3/8" diameter x 1/2" high

Largest Diameter: 1-1/16"(26.9mm)

Overall Length : 2-1/16"(52.4mm)

 

Package includes:

1pcs Router Bit

• T-type High-grade Straight Edge Router Bit, YG6 Alloy Blade with High-grade Welding, Stable Quality, High Efficiency
• Solid hardened steel bodies with anti kickback design. Build-up & heat resistant teflon coating
• Build your own sturdy, attractive, slotted wall to display items from garden tools and power tools to toys – hanging by a hook
• This t-track and t-slot router bit cuts slots for bolts that have a 1-1/16" wide x 5/16" high heads with up to 3/8" shaft diameter
• Used for drilling, installation of the drawer door spherical tip, tip, slat wall boards, plastic products, wood, plywood, etc. more trepanning

User questions & answers

Question:	can you use 5/16 or 3/8 bolts what size t bolts
Answer:	5/16
Question:	can you use 5/16 or 3/8 bolts what size t bolts
Answer:	You could fit up to a 3/8” bolt the slot
Question:	can you use 5/16 or 3/8 bolts what size t bolts
Answer:	It is mostly intended for metal cutting. However you can cut wood with this. Its like using a steak knife to cut butter.

User questions & answers

Question:	Is there a metric set available
Answer:	That's exactly what I used this set for my 80% arms lower receiver. Completed it last week with a Deltron upper and tested it at the range yesterday. Take your time and go slow and it will produce a quality part. Predrill holes with a drill bit. I did the whole process using these to finish with.
Question:	will this set be able to drill my AR15 lower receiver
Answer:	Two or three flute center cutting end mill most 4 flute are not center cutting and will go a horrible job. Two flute end mills in very sharp condition best done on a larger heavy duty drill press 12 inches or more swing. The Quill arbor and bearings need to be tight with minimal slop. Drill press needs to be capable of low speed to avoid chatter. If things are optimal it "may work" any vertical mill even a mini mill will do a better job for this milling operation.
Question:	In drill press, how will they do for plunge cutting? I was under impression I need center cut end mill for boring metal, am I wrong
Answer:	I have been using the 1/4 and 3/8 bits for mortising in cherry wood, they are excellent at that - clean cut, not much vibration, stay sharp longer than other he's spiral bits.
Question:	Are these suited for wood as well
Answer:	End mills don't really have a cutting depth. The general rule is to never plunge more than 1/2 the diameter of the mill. That said this is a nice starter set of end mills. Great for brass and aluminum. Go slow with steel. Use plenty of lube.

Product features

Dimensions

Widely Application

• 4 flutes end mill can be used on many fields, such as metal,wood ,aluminum processing, CNC machining and engineering using, ideal for peripheral and finish milling.
• Suitable for lathes, milling machines, bench drills.drill press and etc.

• Includes both 10pc- 2 flute and 10pc - 4 flute end mills
• Sizes: 3/16", 1/4", 5/16", 3/8", 7/16" (3/8" shank); 1/2", 9/16" (1/2" shank); 5/8", 11/16" (5/8" shank); 3/4"(3/4" shank)
• Made of M2 titanium nitride-coated high speed steel Mill, Center cutting capabilities!
• All in a custom wooden case - approx. dimension: 10-1/4''L x 3-1/4''W x 4-1/2''H

User questions & answers

Question:	What are the cutting depths of each mill
Answer:	Yes
Question:	Are they straight shank
Answer:	No, you would need to modify it by adding CNBC to it. But as it comes s not programmable

Product description

These CNC Router Burrs End MillingEngraving Bits are made of Titanium Coat Carbide Steel, with highly wearresistance, high hardness, bending strength, highly working efficiency, highlyprecision: With sharp cutting edge, milling groove and clean surface, thesesets of tool work quickly and cleanly, no glitches or scrap left

Set of 10 different size to meet yourneeds: 0.8mm, 1mm, 1.2mm, 1.5mm, 1.6mm, 1.8mm, 2mm, 2.4mm, 3mm, 3.175mm)

These CNC router burrs with wide usingapplication: mainly used for cutting and engraving and worked on Acrylic, PVC,Nylon, Resin, PCB circuit board perfectly.

Attention: Don't use on too hard material,like high hardness iron.

• Cutting edge diameter (CED): 0.8-3.175mm (10Pcs, 0.8mm, 1mm, 1.2mm, 1.5mm, 1.6mm, 1.8mm, 2mm, 2.4mm, 3mm, 3.175mm); Cutting edge length (CEL): 6mm; Total length: 38mm; Shank diameter (SHK): 3.175mm
• Wide Compatibility: Works with PCB, SMT, CNC, Mold, plastic fiber, carbon fiber, hard wood, printed circuit board, and other precision parts processing.
• Titanium Coat Carbide Hard Steel: With sufficient flexural strength and wear resistance, ensuring high work efficiency.
• High Quality Material: Using high quality grained carbide material, providing good milling and cutting performance.
• Highly precision: Sharp cutting edge, milling, hole and plate edge, clean surface, neat, no glitches.

Product description

Mitutoyo Edge/Center Finder with 3/8" Shank Diameter, 0.200" Tip Diameter, and cone-shaped center finder.

• Used in a milling machine to find the workpiece edge
• All working surfaces are hardened and ground
• Centerfinder end is used to find hole centers, and aline the spindle with a punch mark or scribed line

User questions & answers

Question:	Showing ":Inside Depth -4.7 inches " I am taking for granted that this is the total length
Answer:	I have a variety of edge finders for different situations. I wish there was a one size fits all edge finder.
Question:	Do you find a need for the different styles of these (multi-packs), or would this suffice for most situations
Answer:	It depends how much of the shaft you insert into the collet
Question:	how long is the shaft that sticks out of the collet
Answer:	Yes. Up to a 3/8 inch bolt will fit

Product description

Thin Parallel Set 1/8" 10 Pair 0.0003" Steel

• Our Part # ALL-54100
• Each parallel is 1/8" thick x 6" long with 2 holes
• Includes 10 pairs of the following heights: 1/2", 5/8", 3/4", 7/8", 1", 1-1/8", 1-1/4", 1-3/8", 1-1/2" & 1-5/8"
• Made from high quality tool steel- stress relieved against distortion, precision ground and hardened Parallel and accurate within +/- .0002" and made from high quality tool steel- stress relieved against distortion, precision ground and hardened

User questions & answers

Question:	What is the size of the holes and how far apart are they
Answer:	Correct. 10 matched sets (20 pieces). I was impressed in quality for the price for sure!
Question:	Description says "10 pair". So are there 20 bars, 2 of each size, each one 6 inches long? Thanks
Answer:	these do not come with any paperwork or certifications.
Question:	Does this come with any certification or paperwork
Answer:	These area manufactured in China.
Question:	Where's it made? (obviously not usa, europe, japan, etc). hoping (for the price) it's taiwan, but assuming it's prc china. any info
Answer:	The total length is 3.5" diameter is 3/8" rear tip is 3/16" diameter and you guess the front tip is tapered.