14 best pro lift floor jacks

Product description

Fit Under Low Ground Clearance Vehicle

Pro-Lift F-767 Grey Low Profile Floor Jack is a 2 Ton floor jack that give you better access to low ground clearance vehicle. And,give you the lifting range from 3-1/2 inches to 14 inches.

The Jack can be fit under a clearance of 3-1/2 inches and maneuvered easily into position.

Pro Lift F-767 floor jack also features the heavy duty steel construction that provides the long lasting durability.

Pro Lift unique patented bypass device protects against over pumping. Its built-in safety valve provides overload protection.

- Extra Low Profile

- Lifting Range from 3-1/2 inches to 14 inches

- Patented bypass device protect over pumping

- Built-In Safty Valve Provides overload protection

Pro Lift F-767 floor jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Take one now to access to the areas you never access before.

• Extra low profile
• Lifting range of 3-1/2 inches to 14 inches
• Patented bypass device protects against over pumping for safe operations
• Built-in safety valve provides overload protection. Rust Resistant
• Heavy duty steel construction provides long term durability

User questions & answers

Question:	Does it come with a portable case
Answer:	No, but the box it comes in is pretty sturdy. If you remove the cardboard packing the jack easily slides back into the box. The inside bottom of the box is reinforced. Not sure how long it will hold up, but it’s better than nothing.
Question:	Will this raise a 2011 cadillac cts enough to get jack stands underneath it? i want to change transmission oil ... thanks
Answer:	A Cadillac CTS is roughly 4,300 pounds. Which is a little over the capacity of this jack. As long as you're placing it on jack stands and you don't leave the jack holding it too long, it should be okay. Although all the armchair experts on this site will implore you to buy a 3 or 4 ton jack. Just remember to always put the car on jack stands and do your work on a flat, level surface.
Question:	Can anyone tell me the outside diameter of the lifting cup? Thanks
Answer:	The cup itself is 2 1/4 inches, with the inner portion (The part that spins freely, with the 4 tabs) 1 7/8ths, and the tabs extend about 1/4 inch up from the cup. Hope this helps.
Question:	What kind of oil does this take? The screw was loose when it was shipped to me and some oil had poured out into the box. I just want to top it off
Answer:	hydraulic jack oil. The screw IS loose upon arrival. If you read the SHORT instructions....this (grey) screw is HOW TO LOWER the jack when you are done lifting and have supported the weight/vehicle with jack stands. Turning just a bit using the handle you used to pump up the vehicle - you will notice it lower ever so gently. ONCE it is fully lowered - it is best to immediately turn the screw clockwise until it stops - this prepares the jack for its next use. Do this so you will not forget it is closed. IMO - some people with oil spewing - did not 'get it' how important it is to assure the valve is closed BEFORE raising the vehicle.

Product features

Pro-Lift F-767 Grey Low Profile Floor Jack - 2 Ton Capacity

About Us:

Our ProLift hydraulic automotive jacks, lifts and garage equipment range will cater to many 'do it yourself' enthusiast. The product line includes bottle jacks, floor jacks, garage jacks, aluminum jacks. scissor jack, lawn mower lifts, utility lifts, chokes, dirt bike lift, creepers, mechanic seats and more! Explore our range on the products page.

ProLift has become a global presence in the go to automotive garage maintenance equipment with locations in the United States, The Netherlands, Taiwan and Australia. We create dependable and reliable performance hydraulic equipment.

Product description

1 to 2 Strokes to Allow You to Lift Immediately to Your Desired Load Height

Pro-Lift G-737 Garage Jack is a 3-1/2 garage jack that features speedy lift function. It allows you to immediately lift to your desired load height with 1 to 2 strokes.

It also features universal joint release mechanism to provide precision control of load descent in any handle position.

Pro Lift G-737 Garage Jack is built with the rolled side frame to add strength and reduce twisting. And, its rear swivel casters give you the easy jack positioning. In addition, it features the rubber saddle pad to protect the vehicle while working with the jack

Plus, there is a magnetic tool tray built - in. It gives you the place to keep small parts around the job site for convenience.

- Rubber Saddle Pad to Protect the Vehicle While Working with the Jack

- Universal Joint Release Mechanism to Provide Precision Control

- Magnetic Tool Tray for Convenience, Also Speedy Lift Technology

- Rolled Side Frame and Rear Swivel Casters

Specifications

- Capacity: 3-1/2 Ton

- Lift Range: 5-1/2 to 22 inch

- Package Dimension: 30.3 x 6.9 x 15.75 inch

- Item Weight: 90 Lbs

Pro Lift G-737 Garage Jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Click the buy button now to get your Speedy Lift Garage jack

• The product is 3-1/2 ton garage jack
• Easy and simple use kit
• The product is manufactured in china
• Rubber saddle protects the vehicle while lifting the vehicle
• Universal Joint release mechanism provides precision control of load descent in any handle position
• Magnetic tool tray keeps the small parts around the job site for convenience
• Rolled side frame adds strength to reduce twisting; professional grade
• Foam handle provides comfort to the user while pumping

User questions & answers

Question:	Is this jack "speedy" with weight on it? Or only until you get it started
Answer:	Capacity: 3-1/2 Ton- Lift Range: 5-1/2 to 22 inch- Package Dimension: 30.3 x 6.9 x 15.75 inch- Item Weight: 90 Lbs
Question:	How long is the handle
Answer:	The saddle w/rubber pad is removable and I suppose if you had a trans adapter that mounts the same. I would check with the manufacture, Shinn Fu America.
Question:	What is the range of lift height in inches
Answer:	This is a 6000 lbs jack with lifting range 11 - 21 inches mainly for truck and large SUV. Toyota Corolla is a small car and the bottom height seems not high enough to put this jack underneath. You may look at other Powerbuilt lower profile jack such as below links https://www.amazon.com/Powerbuilt-620484-Inflactor-Electric-inflator/dp/B01N7RFSGG/ref=sr_1_8?dchild=1&keywords=powerbuilt+jack&qid=1610355068&sr=8-8 https://www.amazon.com/Powerbuilt-240076-Profile-Fast-Floor/dp/B07FSTQ944/ref=sr_1_2?dchild=1&keywords=powerbuilt+jack&qid=1610355233&sr=8-2
Question:	Can the saddle be removed to install a trans jack adapter
Answer:	The 4000 pound Unijack offers lift range from 8-5/8 to 18-3/8 inches, which makes it perfect for sedans, minivans and crossovers. Read more at https://www.powerbuilt.com/products/4000-lb-unijack-bottle-jack-jackstand-in-one#RhgJ8m0L7kYgLlRe.99

Product features

Pro-LifT G-737 Grey Speedy Lift Garage Jack - 3-1/2 Ton Capacity

• Innovative design of Speedy Lift technology offers a quick lift for professional performance
• Swivel saddle provides easy jack positioning and user safety
• Heavy duty, steel construction provides safe use and long term durability
• Bypass device prevents over pumping
• Built-in internal safety valve ensures safe operation
• Rear caster for easy jack positioning

Product description

Pro Lift G-4630JSCB Mechanics Set features 3 Garage Essentials in one convenient package. It comes with 3 Ton Garage Jack, 3 Ton Jack Stand, and 300 lbs detachable Creeper. The Garage Jack with the 3 Ton Capacity features the steel frame construction for the added strength and durability. With the 3" roller casters, they ensure the portability and stability. The Garage Jack is designed to lift, but not support one end of a vehicle. It must be used in conjunction with the pair of 3 Ton jack stands provided. The jack stands have the 3 Ton capacity. Install the ratchet bar into the frame. The ratchet portion of the bar must be aligned with the ratchet pawl. The creeper has the 40" in length with the capacity of 300 lbs. With 6 casters, it provides users with the easy maneuverability. Key Features 3 Ton Capacity Garage Jack with 3" Roller Casters Steel Frame Construction for Added Strength and Durability Bypass Mechanism Prevents over Pumping and Ensures Safe Operation Meets or Exceeds ASME PASE 2014 Safety Standards 3 Ton Jack Stands (Pair) and 40" Mechanic Creeper with 300 Lbs Capacity Specifications - Capacity: 3 Ton (Garage Jack & Jack Stands)- Lift Range: 5-1/2 to 18-1/2 inch Floor Jack & 11-5/6 to 16-3/4 inch Jack Stands- Package Dimension: 37. 38 x 16. 5 x 14. 5 inch- Item Weight: 93. 5 Lbs Content 3 Ton Garage Jack 3 Ton Jack Stands (Pair) 40" Mechanic Creeper Instruction Manual

• Pro Lift G-4630JSCB Mechanics Set features 3 Garage Essentials in one convenient package. It comes with 3 Ton Garage Jack, 3 Ton Jack Stand, and 300 lbs detachable Creeper.
• The Garage Jack with the the 3 Ton Capacity features the steel frame construction for the added strength and durability. With the 3" roller casters, they ensure the portability and stability.
• The Garage Jack is designed to lift, but not support one end of a vehilce. It must be used in conjunction with the pair of 3 Ton jack stands provided.
• The jack stands has the 3 Ton capacity. Install the ratchet bar into the frame. The ratchet portion of bar must be aligned with the ratchet pawl.
• The creeper has the 40" in length with the capacity of 300 lbs. With 6 casters, it provides users with the easy maneuverability.
• Fit Type: Universal Fit

Product features

3 Ton Floor Jack, Jack Stand and Mechanic Creeper Combo

Pro-Lift G-4630JSCB Mechanics Set features 3 Garage Essentials in one convenient package. It comes with 3 Ton Garage Jack, 3 Ton Jack Stand, and 300 lbs detachable Creeper. The Garage Jack with the 3 Ton Capacity features the steel frame construction for the added strength and durability.

Pro-LifT G-4630JSCB 3 Ton Heavy Duty Floor Jack and Jack Stands and Creeper Combo - Great for Service Garage Home Uses - Black

• Come with 3 Ton Garage Jack, 3 Ton Jack Stand (pair), and 300 lbs detachable Creeper
• Designed with steel frame construction for added strength & durability. With 3" roller casters, ensure portability & stability
• Lifting range between 5-1/2" to 18-1/2", allows to easily access under vehicles for auto repair services
• 3 Ton Jack is designed to lift, not support. Used with pair of 3 Ton jack stands provided
• Creeper with 40" long & 300 Lbs capacity, floor jack combo provides All in One repair needs

Product description

Pro-Lift F-2330BMC is Pro Lift 2 Ton floor jack and 2 Ton jack stand combo.

Both floor jack and jack stands are built with heavy duty steel to provide you the long lasting durability. The floor jack features the bypass device that protects from over pumping for safe operation.

With two front wheels and two rear swivel casters, it makes the maneuver smooth and easy. In addition, with the swivel saddle, it provides easy positioning and safety. There is also carrying handle on the jack to enhance the portability.

In the combo pack, there are pair of ratcheted 2 ton jack stands included to safely support your lifted vehicle. The jack stands feature the high quality cast ductile iron ratchet bar. At the same time, with the height adjustment mechanism, it allows smooth upward movement while releasing handle locks into position.

In the combo kit, you will also find a convenient blow molded storage case. It gives you the ability to easily store and carry.

- Built with the Heavy Duty Steel with Two Front Wheels and Two Rear Swivel Casters

- Bypass Device Protect from Over Pumping Damage

- High Adjustment Mechanism and High Quality Cast Ductile Iron Ratchet Bar

- Packed in a convenient blow molded storage case

Specifications

- Capacity: 2 Ton (Floor Jack & Jack Stand)

- Lift Range: 5-1/4 to 13 inch Floor Jack & 10-1/2 to 16-3/4 inch Jack Stands

- Package Dimension: 30.71 x 9.85 x 5.71 inch

- Item Weight: 36 Lbs

Pro Lift F-2330BMC 2 Ton Floor Jack & Jack Stand Combo is backed by 90 Days warranty from the date of the purchase.

• Heavy duty steel construction
• Convenient blow molded storage case
• Carrying handle on jack
• Swivel casters for easy positioning
• Pair of ratcheted 2 ton jack stands included to safely support your lifted vehicle

User questions & answers

Question:	Can lift ford ranger
Answer:	each jack is 2 ton
Question:	It's this jack strong enough for a 2000 Chevy Astro Van
Answer:	No
Question:	What is the diameter of the pad? I'd like to buy an adapter too and want to make sure it fits
Answer:	Only if you have the older HF Pittsburgh 3 ton jack stands, item 38846. The new Harbor Freight 3 ton jack stands, item 62392 will NOT fit. The saddle is much too thin, almost half the thickness of these pads. HF really cheapened them.
Question:	Is each jack stand rated at 2 ton
Answer:	Yes, they fit mine nicely.

Product features

Pro-LifT F-2330BMC Grey Floor Jack and Stand Combo

• A great combo kit including a 2 Ton jack and 2 Two Ton jack stands in a blow mold carry case. This kit is easy to transport, and simple to store. If your shop is mobile, this kit is definitely for you!
• Patented bypass device protects against overpumping for safe operation
• Heavy duty steel construction provides long term durability
• Swivel saddle and swivel rear casters provide easy positioning and safety
• High quality cast ductile iron ratchet bar
• Height adjustment mechanism allows smooth upward movement while release handle locks into position
• Ideal for auto, truck service, farm, and shop use

Product description

Pro Lift F-2332 Floor Jack is a 2 ton floor jack that is design to meet the latest ASNI/PALD requirements. It gives you the ability to lift from 7-1/8 inch to 13-5/8 inch.

It is built with heavy duty steel construction to provide you the long term durability. The swivel saddle and swivel rear casters enhance the safety and provide the ability to position the load easily.

For the safety operation, Pro Lift F-2332 has the patented bypass device built-in to protect against over pumping. Also, the built-in safety valve provides the protection from overload.

In addition, there is an easy carrying handle to give you the convenience to carry it around. Ultimately, it provides you with the portability and durability that you need.

- Patented bypass device protects against over pumping for safe operation

- Built-in safety valve provides long term durability

- Swivel rear casters provide easy positioning and safety

- Easy carrying handle for user convenience

Specifications

- Capacity: 2 Ton

- Lift Range: 7-1/8 to 13-5/8 inch

- Package Dimension: 18.31 x 8.86 x 5.71 inch

- Item Weight: 19 Lbs

Pro Lift F-2332 2 Ton Floor Jack is backed by 90 Days warranty from the date of the purchase.

• The product is 2t hydraulic for jack
• Easy and simple use kit
• The product is manufactured in china
• Patented bypass device protects against over pumping for safe operation
• Built-in safety valve provides long term durability
• Swivel rear casters provide easy positioning and safety
• Has an easy carrying handle for user convenience
• Pro-Lift hydraulic jacks are designed to meet or exceed latest ANSI/PALD requirements

User questions & answers

Question:	Bottom height setting
Answer:	Down about 4””
Question:	How high will it lift have a ranger and wonder if it will get high enough to change a tire
Answer:	lift about 13 inches
Question:	Is this made in the USA
Answer:	No. Its a turd do not buy. It gave out on me while lifting 1 wheel on a car on its second use. Not safe
Question:	Is the lift height measured Fromm the floor or from the top of the lowered jack
Answer:	It gives you the ability to lift from 7-1/8 inch to 13-5/8 inch. that is a direct copy from the description on Amazon....That means it needs a little over 7 inches of clearance under the object you wan to lift and it will lift it up to a little under 14 inches...My math by order of subtraction means it lifts the object a massive amount of about 6 and a half inches.

Product features

Pro-LifT F-2332 Grey Hydraulic Floor Jack - 2 Ton Capacity

• Patented bypass device protects against overpumping for safe operation
• Built-in safety valve provides overload protection
• Heavy duty steel construction provides long term durability
• Swivel saddle and swivel rear casters provide easy positioning and safety
• Lifting Range: 5-3/8" to 13-5/8"

Product description

The Pro-Lift G-5152 1-1/2 Ton Hybrid Garage Jack aluminum/steel design combines lightweight and strength for longevity.

• Aluminum/steel design combines lightweight and strength for longevity
• Side frame handles allow for easy carrying
• Extra-wide wheels designed for stability under load stress
• Dual piston speedy lift lightweight service jack
• Lifting range from 3-1/2" to 14" allows you can gain easy access under low-profile vehicles

Product description

Great Addition to any Garage and Home

Pro-Lift B-S12D Grey Hydraulic Bottle Jack is a 30 ton bottle jack that is ideal for auto, truck service, farm and shop use. With the heat treated critical stress areas, it ensures long life performance. In addition, the carrying handle makes it so easy to carry around wherever need it.

It features the steel lifting saddle that is engineered to hold load securely.

With the extension screw, it allows Pro Lift B-S12D Bottle Jack to be adjusted to accommodate desired work height.

Pro Lift B-S12D Bottle Jack also features Built-In bypass system to protect against ram over-travel.

- Steel Lifting Saddle Engineered to Hold Load Securely

- Extension Screw Adjusts to Accommodate Desired Work Height

- Built-In Bypass System to Protect against Ram Over-Travel

- Heat Treated Critical Stress Areas

- Designed to Meet the Latest ANSI/PALD Standards

Specifications

- Capacity: 12 Ton Shorty

- Lifting Range: 6 x 10-5/8 inch

- Carrying Handle: Yes

- Item Weight: 14 Lbs

Pro Lift B-S12D Bottle Jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Grab one now to add to your home tool set

• Steel lifting saddle engineered to hold load securely
• Extension screw adjusts to accommodate desired work height
• Built-in bypass system protects against ram over travel
• Heat treated critical stress areas ensure long life performance
• Designed to meet ANSI/PALD standards

User questions & answers

Question:	What is the ram diameter or top diameter of screw top where it lifts
Answer:	The ram-bore is 1-5/8", and the FOOT on top is 1-1/2" at the adjustable screw top.
Question:	Will this fit under a 2015 Charger for a tire change
Answer:	Good question, it may, only because the charger sits lower to the ground than, my '97 Jeep grand Cherokee Laredo, remember you should take in consideration of the tire size your Charger uses, does the tires lift the car higher off the ground, if not than it should fit
Question:	Is it America made
Answer:	No.
Question:	what is the total height of this jack before extending? relaxed
Answer:	The jack is 6" tall before extending, and it is not junk, I lift my 34ft fifth wheel trailor one wheel at a time and it stays up.

Product features

Pro-LifT B-S12D Grey Hydraulic Bottle Jack - 12 Ton Capacity

• Steel lifting saddle cleated for load gripping power
• Extension screw adjusts to accommodate work height
• Patented bypass device protects against over-pumping
• Heat treated critical stress areas ensure long life performance
• Carrying handle
• Ideal for auto, truck service, farm, and shop use

Product description

Pro lift T-6906D is a 6-ton double locking jack stands. It features a high quality cast ductile Iron Ratchet bar and sturdy stamped steel base provide durability and longevity which makes ideal for home, professional and farm use. Always used in pairs, counter weighted pawls serve as a safe secure locking device to prevent the load from accidental disengagement. An attached pin lock provides support, locking the ratchet bar in place for an additional carrying point. One piece, multi position ductile ratchet bar provides strength and durability as well as a quick adjustment mechanism that securely locks into the desired position.

• Sturdy stamped Steel Construction with 6 ton capacity
• High quality cast ductile iron ratchet bar
• Double locks mechanism with both handle locks and mobility pin
• Height adjustment mechanism allows smooth upward movement while release handle locks and mobility pin
• Meets or exceeds ANSI/PALD standards. Ideal for home, Auto, truck service, farm, and shop use
• Comes with 2 Adjustable Beam and a Single stand;It has both commercial and residential applications

User questions & answers

Question:	Is the pin attached to the back so it doesn't get lost
Answer:	I took some measurements for you. Base weight 8.6 pounds Tongue weight 4.8 pounds Weight per stand 13.4 pounds each Total weight per set of 2 jack stands 26.8 pounds Tongue head contact size 1 inch x 3-31/32 inches Number of notches in tongue 11 Distance between notches in tongue: 3/4 inch steps Base stand dimensions 9 inches x 10-3/8 inches All height measurements are from floor to lowest U shaped contact point in tongue head (true resting point) Minimum lift height tongue base resting on floor: 14-3/16 inches Minimum height to first notch (non locking): 15-7/16 inches Minimum height to first locking notch: 16-1/8 inches Maximum lift height (locking) 22-7/8 inches. Note the lift is a little higher if you add the top of the saddle points, that is if the object is not resting in the U shaped saddle but at the top of the crown-ridges Weld quality-good/acceptable box and packing o.k. capacity as stated in literature: 6 tons per pair Country of manufacture: China Based on the above, I bought a second set, as I liked the first set.
Question:	Are these 6 tons each or 2 three ton stands that equal 6 tons
Answer:	Lifting range is 6-3/8" to 22".
Question:	How high they can extend and hold
Answer:	china
Question:	Please add some more info to your listing. What's the minimum and maximum clearance? What are the dimensions on the heads? Base
Answer:	These jacks will hold 3 tons or 6,000 pounds. Since you won’t be holding the entire weight of your vehicle you should be fine. These are great light weight jacks for tire changes and auto maintenance too.

Product features

Pro-LifT Double Pin Jack

Pin style jack stands offer the ultimate in security and safety. All Black-hawk Automotive pin style stands are offer some of the best values on the market today.

• Sturdy stamped steel construction
• Height adjustment mechanism allows smooth upward movement while release handle locks into position
• Ideal for auto, truck service, farm, and shop use

Product description

Giving you the Room and Stability to Work Safely on Lawn Mowers in Three Easy Steps

Pro Lift T-5305 Heavy Duty Lawn Mower Lift Kit is a 500 Lbs. lawn mower lift that provides the ability to lift 26-1/2 inches from ground to wheel saddle to give you the maximum space to perform necessary mower maintenance, such as blade works, cleaning debris, oil change, and more.

It is built with the welded solid steel construction with the four steel wheels and the positive dual locking safety latches.  With the universal design, Pro Lift T-5305 is adjustable to fit most zero turn garden tractors, riding mowers, ATVs and even push mowers.

It has the ability to hold a minimum of 19-1/4 inch span and up to a 42-1/2 inch span mower.

In addition, it features the hydraulic foot pedal operation. It gives you the option to lift up your mower effortless.

To lower the lift, put the mower in neutral and raise Lift Platform slightly to disengage Height Locking Levers, then use the release knob to carefully turn release valve counterclockwise, lowering the load slowly.

- Safety Lock for Safely Supporting the Load

- Rubber Padded Platform to Prevent Scratching and to Protect your Machine

- Non-Slip Foot Pedal Allows Effortless Lifting the Load

- Easily Maneuverable and Adjustable for a Wide Variety of Machine

Specifications

- Capacity: 500 Lbs

- Lifting Height: 26-1/2 Inches

- Wheel Span: 19-1/4 to 42-1/2 Inches

- Base Size: 40 x 15-7/8 inches

- Item Weight: 89 Lbs

Pro Lift T-5305 Lawn Mower Lift is backed by 90 Days warranty from the date of the purchase.

• 500 LB CAPACITY - T-5305 Lawn Mower Lift is built with the welded solid steel construction with the four steel wheels and the positive dual locking safety latches.
• Over 26-INCH Lifting Height - It provides the maximum space to perform necessary maintenance, such as Blade Works, Cleaning Debris, Oil Change, and more.
• 19-1/4 to 42-1/2 INCHES WHEEL SPAN - With the adjustable wheel span, it fits on most zero turn garden tractors, riding mowers, ATVs, and even push mowers.
• EASY TO LIFT & LOWER - Position mower tires securely on wheel baskets and centering the load on lift. To lower lift, raise Lift Platform slightly to disengage Height Locking Levers then use the release knob to carefully turn release valve counterclockwise, lowering the load slowly.
• WARRANTY - Pro Lift Plastic Creeper is covered 90 Days limited warranty from the date of purchase. Due to a defect in material or workmanship under normal usage, we will repair or replace at its option.

User questions & answers

Question:	Will this work for a John Deere X500 , 54 inch cut multi-terrain tractor
Answer:	Hi Amazon Customer. Yes, all our riding lawn mowers are equipped for attaching both rear- and front-mounted lawn and garden accessories like trailers, garden dump carts, snow blades, snow throwers, graders, spreaders, dethatchers, aerators, brooms, rollers, and more. You can easily adapt your tractor to the season and/or task! Thank you so much for considering Husqvarna for your outdoor power equipment needs.
Question:	Can I buy just the jack for this, it just quit working on me, probably an issue with the seal but regardless I need a new hydraulic on it
Answer:	Briggs Stratton twin V 24
Question:	is the wheel base measured from the outside of the tire or the inside my tires are 14 inches apart will it fit
Answer:	The transmisions for Husqvarna are sourced from other companies such as Hydrogear. They don't have Husqvarna part numbers. If you are having a major problem with your transmission, I suggest reaching out to a local Husqvarna dealer for diagnosis and repair.
Question:	Can this work with a snow blower tractor attachment
Answer:	The answers from the manufacturer and sellers are so wrong as to be scary. 24v stands for the 24 horsepower V twin engine. There is not a 24 volt battery in tbis and I find it scary that the "experts" dont know the first thing about this product. What is going to happen if there is a problem when someone tries to hooks 2 12volt batteries up to this and fries the electrical system and starts to on fire? Uggh

Product features

500 LB Capacity

T-5305 Lawn Mower Lift is built with the welded solid steel construction with the four steel wheels and the positive dual locking safety latches.

It provides the ability to lift 26-1/2 inches from ground to wheel saddle to give you the maximum space to perform necessary mower maintenance, such as blade works, cleaning debris, oil change, and more.

It is built with the welded solid steel construction with the four steel wheels and the positive dual locking safety latches. With the universal design, is adjustable to fit most zero turn garden tractors, riding mowers, ATVs and even push mowers.

In addition, it features the hydraulic foot pedal operation. It gives you the option to lift up your mower effortless.

To lower the lift, put the mower in neutral and raise Lift Platform slightly to disengage Height Locking Levers, then use the release knob to carefully turn release valve counterclockwise, lowering the load slowly.

Specifications

• Safety Lock for Safely Supporting the Load
• Rubber Padded Platform to Prevent Scratching and to Protect your Machine
• Non-Slip Foot Pedal Allows Effortless Lifting the Load
• Easily Maneuverable and Adjustable for a Wide Variety of Machine
• Capacity: 500 Lbs
• Lifting Height: 26-1/2 Inches
• Wheel Span: 19-1/4 to 42-1/2 Inches
• Base Size: 40 x 15-7/8 inches
• Item Weight: 89 Lbs

Over 26-Inch Lifting Height

Provides the maximum space to perform necessary maintenance, such as Blade Works, Cleaning Debris, Oil Change, and more.

19-1/4 To 42-1/2 Inches Wheel Spana

With the adjustable wheel span, it fits on most zero turn garden tractors, riding mowers, ATVs, and even push mowers.

Easy To Lift & Lower

Position mower tires securely on wheel baskets and centering the load on lift. To lower lift, raise Lift Platform slightly to disengage Height Locking Levers then use the release knob to carefully turn release valve counterclockwise, lowering the load slowly.

Product description

Giving you the Room and Stability to Work Safely on Lawn Mowers in Three Easy Steps

Pro Lift T-5300 Lawn Mower Lift is a 300 Lbs. lawn mower lift that provides the ability to lift 22 inches from ground to wheel saddle to give you the maximum space to perform necessary mower maintenance.

It is built with the welded solid steel construction with the four steel wheels and the positive dual locking safety latches.

It has the ability to hold minimum of 17-1/4 inch span and up to a 41-1/4 inch span mower.

In addition, it features the hydraulic foot pedal operation. It gives you the option to lift up your mower effortless.

At the same time, to lower the lift, put the mower in neutral and raise Lift Platform slightly to disengage Height Locking Levers, then With the universal design, Pro Lift T-5300 is adjustable to fit most zero turn garden tractors and riding mowers.

- Safety Lock for Safely Supporting the Load

- Rubber Padded Platform to Prevent Scratching and to Protect your Machine

- Non-Slip Foot Pedal Allows Effortless Lifting the Load

- Easily Maneuverable and Adjustable for a Wide Variety of Machine

Specifications

- Capacity: 300 Lbs.

- Lifting Height: 22 Inch

- Wheel Span: 17-1/4 to 41-1/4 inches

- Item Weight: 55Lbs

Pro Lift T-5300 Lawn Mower Lift is backed by 90 Days warranty from the date of the purchase.

• Safety Lock for Safely Supporting the Load
• Rubber Padded Platform to Prevent Scratching and to Protect your Machine
• Non-Slip Foot Pedal Allows Effortless Lifting the Load
• Easily Maneuverable and Adjustable for a Wide Variety of Machine

User questions & answers

Question:	Where is this made
Answer:	I put my camera in. It has a 200mm lens attached and it was tight putting it in horizontally. Vertically there is a ton of room, even for more than a cell phone. Hope this helps.
Question:	Is it a hydrualic
Answer:	Probably would work, but not really the designed purpose.
Question:	Will this lift be suitable for a poulan pro zt 48” mower
Answer:	why would you do that.
Question:	does it fold up for storage
Answer:	It has only been completely submerged once, and yes, it floated. I don't think it would do well for a long time in the water - hope I don't have to find out!

Product features

Mower Jack Lift for Tractors and Zero Turn Lawn Mowers

To Safely Supporting the Load.

Rubber Padded Platform

Prevents from Scratching and Protects Your Lawn Mower.

Non-Slip Foot Pedal

Allows Effortless Lifting the Load.

Drive Mower Onto Wheel Baskets

Positions mower tire securely on wheel baskets centering the load on the lift.

To Raise the Lift

Turns the release valve clockwise until firm resistance is felt. Carefully pumps jack until mower reaches desired height. Final height must correspond with the locking teeth on the Height Locking levers.

Secure Locking Lever

Carefully turn the Release valve counter clockwise, slowly, until the Lift Platform locking levers engages the Height Locking Levers then close the release valve by turning it fully clockwise until firm resistance is felt.

To Lower the Lift

Pumps the lift Pedal several times to disengage the Height Locking Levers. Carefully turn the Release valve counter-clockwise, slowly, but no more than 1 turn from the closed position, to lower the load slow and safe.

Product description

Pro-Lift B-002D Grey Hydraulic Bottle Jack is a 2-ton bottle jack that is ideal for auto, truck service, farm and shop use. With the heat treated critical stress areas, it ensures long life performance. In addition, the carrying handle makes it so easy to carry around wherever need it.

It features the steel lifting saddle that is engineered to hold load securely.

With the extension screw, it allows Pro Lift B-002D Bottle Jack to be adjusted to accommodate desired work height.

Pro Lift B-002D Bottle Jack also features Built-In bypass system to protect against ram over-travel.

- Steel Lifting Saddle Engineered to Hold Load Securely 

- Extension Screw Adjusts to Accommodate Desired Work Height 

- Built-In Bypass System to Protect against Ram Over-Travel 

- Heat Treated Critical Stress Areas 

- Designed to Meet the Latest ANSI/PALD Standards

Specifications

- Capacity: 2 Ton 

- Lifting Range: 7-1/8 x 13-5/8 inch 

- Carrying Handle: No 

- Item Weight: 7 Lbs

Pro Lift B-002D Bottle Jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Grab one now to add to your home tool set

• The product is 2Ton bottle jack
• Easy and simple use kit
• The product is manufactured in china
• Steel lifting saddle engineered to hold load securely
• Extension screw adjusts to accommodate desired work height
• Built-in bypass system protects against ram over travel
• Heat treated critical stress areas ensure long life performance

User questions & answers

Question:	Is the 13 5/8" maximum height including the jack itslef, or is that how much higher it can lift
Answer:	Lifting wheel, not frame, provided the height of jack can be placed under a wheel suspension point (7.5"clearance) will net a height of 13 5/8" lift of wheel center.
Question:	Will it fit under a car with only 5-6 inches clearance
Answer:	No, the jack is 6 inches tall at least. U need a floor jack for your car.
Question:	What is the minimum height
Answer:	7 1/2 inches is the minimum height
Question:	How tall is it
Answer:	It measures 7 1/2 inches from floor to top of Jack

Product description

Great Addition to any Garage and Home

Pro-Lift B-008D Grey Hydraulic Bottle Jack is a 8-ton bottle jack that is ideal for auto, truck service, farm and shop use. With the heat treated critical stress areas, it ensures long life performance. In addition, the carrying handle makes it so easy to carry around wherever need it.

It features the steel lifting saddle that is engineered to hold load securely.

With the extension screw, it allows Pro Lift B-008D Bottle Jack to be adjusted to accommodate desired work height.

Pro Lift B-008D Bottle Jack also features Built-In bypass system to protect against ram over-travel.

- Steel Lifting Saddle Engineered to Hold Load Securely 

- Extension Screw Adjusts to Accommodate Desired Work Height 

- Built-In Bypass System to Protect against Ram Over-Travel 

- Heat Treated Critical Stress Areas 

- Designed to Meet the Latest ANSI/PALD Standards

Specifications

- Capacity: 8 Ton 

- Lifting Range: 8-7/8 x 17-3/8 inch 

- Carrying Handle: Yes 

- Item Weight: 13 Lbs

Pro Lift B-008D Bottle Jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Grab one now to add to your home tool set

• The product is 8Ton bottle jack
• Easy and simple use kit
• The product is manufactured in china
• Steel lifting saddle engineered to hold load securely
• Extension screw adjusts to accommodate desired work height
• Built-in bypass system protects against ram over travel
• Heat treated critical stress areas ensure long life performance
• Designed to meet ANSI/PALD standards

User questions & answers

Question:	Screw extension range
Answer:	I have used the screw extension...not exactly sure as it's been awhile but it's at least 2 inches maybe 3. Its packed and not easy accessible.
Question:	Where can i buy an extension handle
Answer:	I'm not sure, but my handle from an old 2 ton floor Jack works better than the handle that come with this jack.
Question:	I ordered this item on the tenth but still have not recieved it. the tracking number doesn’t work with usps, however it does work for ups. refund me
Answer:	Check your account if the money has been withdrawn then contact Amazon customer service and inform them of your issue. You can also contact UPS (since the tracking number works for them) and see if they have your Package. If all else fails CONTACT THE SELLER!
Question:	Could this bottle jack be stored sideways under the backseat in my truck or is there a chance for oil to leak that way
Answer:	i have never had an issue with the jack leaking while laying on its side

Product description

Great Addition to any Garage and Home

Pro-Lift B-020D Grey Hydraulic Bottle Jack is a 20-ton bottle jack that is ideal for auto, truck service, farm and shop use. With the heat treated critical stress areas, it ensures long life performance. In addition, the carrying handle makes it so easy to carry around wherever need it.

It features the steel lifting saddle that is engineered to hold load securely.

With the extension screw, it allows Pro Lift B-020D Bottle Jack to be adjusted to accommodate desired work height.

Pro Lift B-020D Bottle Jack also features Built-In bypass system to protect against ram over-travel.

- Steel Lifting Saddle Engineered to Hold Load Securely 

- Extension Screw Adjusts to Accommodate Desired Work Height 

- Built-In Bypass System to Protect against Ram Over-Travel 

- Heat Treated Critical Stress Areas 

- Designed to Meet the Latest ANSI/PALD Standards

Specifications

- Capacity: 20 Ton 

- Lifting Range: 9-1/2 x 18-7/8 inch 

- Carrying Handle: Yes 

- Item Weight: 25 Lbs

Pro Lift B-020D Bottle Jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Grab one now to add to your home tool set

• The product is 20Ton bottle jack
• Easy and simple use kit
• The product is manufactured in china
• Steel lifting saddle engineered to hold load securely
• Extension screw adjusts to accommodate desired work height
• Built-in bypass system protects against ram over travel
• Heat treated critical stress areas ensure long life performance
• Meets or exceeds ASME/PASE standards

User questions & answers

Question:	what oil does it uses
Answer:	Hydraulic oil
Question:	Difference between this and the B-S20D
Answer:	I never received this item so I am not sure
Question:	can this jack be used in a press frame
Answer:	Yes
Question:	can you connect a pressure guage to the port next to the relief valve
Answer:	Yes with proper connection

Product features

Pro-Lift B-020D Grey Hydraulic Bottle Jack - 20 Ton Capacity

• Steel lifting saddle cleated for load gripping power
• Extension screw adjusts to accommodate work height
• Patented bypass device protects against over-pumping
• Heat treated critical stress areas ensure long life performance
• Carrying handle
• Ideal for auto, truck service, farm, and shop use

Product description

Compact, Light Weight to Carry in Your Automotive

Pro-Lift T-9456 Grey Scissor Jack is the 3000 pound capacity scissor jack. It is a great light weight jack for the garage or to carry in your automobile.

The compact size and the light weight make it easy to position and the handle design makes it easy to lift.

With its built-in extra wide base, it provides you with the additional stability.

Pro-Lift T-9456 Grey Scissor Jack gives you the lifting range from 3-3/4 inches to 15-1/8 inches

- Extra Wide Base for Extra Stability

- Lifting Range from 3-3/4 inches to 15-1/8 inches

- 3,000 Pound Rated Weight Capacity Scissor Jack

- Meets or exceeds the latest ANSI/PALD standards

Specifications

- Capacity: 3000 Lbs

- Package Dimension: 17.2 x 3.9 x 4.7 inch

- Lifting Range: 4-1/8 to 15-1/8 inch

- Item Weight: 9 Lbs

Pro Lift T-9456 Scissor Jack is backed with SFA 90 Days Warranty from the Date of Purchase.

Grab one now to carry in your automobile.

• The product is 3000lb scissor jack
• Easy and simple use kit
• The product is manufactured in china
• Extra wide base for extra capacity and stability
• Lifting range from 3-3/4 inches to 15-1/8 inches
• 3,000 pound rated weight capacity scissor jack
• Meets or exceeds the latest ANSI/PALD standards

User questions & answers

Question:	Is there any kind of warranty
Answer:	China. All the products sold in OESS store are made in China.
Question:	Can i use if for cars
Answer:	Hasta el momento no tiene ningun problema, esta plataforma tiene cuatro soportes de hule que ayudan a que no se desplace ni oscile.
Question:	I have a Dodge 2500 truck..Do you think it will work for changing 1 wheel at a time
Answer:	There is some side-to-side mechanical play when fully extended which is about 0.5 to 1.0cm. Also, when fully extended there is some play in the tilt of about 3 degrees. It is not rock solid so it will depend on your application whether or not the mechanical play is an issue or not.
Question:	does it come with handle
Answer:	The maximum loading capacity up to 110lb(50kg)

Product features

Pro-Lift T-9456 Grey Scissor Jack - 3000 lb. Capacity

Features:

• 3,000 lb capacity scissor jack
• Extra wide base for extra capacity
• Lifting range: 4 1/8” to 15 1/8”