13 best 240v garage heaters

Product description

This Smart Technology electric tankless water heater is configured as a "whole home" model for climates where incoming water temperature is 67°F and above. This model is well suited for heating up to 2-Gallon per minute, which is the equivalent of one shower head (with a 1.5 gpm flow) and one sink with a low inlet water temperature of 67°F and an output setting of 105°F. Digital Temperature Control allows you to set your temperature in increments of 1 Degree. This model can also be used in colder climates as a Point of Use for a sink or other low flow application. All tankless water heaters are sized based on flow rate and temperature rise, and there is a direct relationship between the two. So if used in a cold area requiring a high temperature rise, it will be more limited in the amount of fixtures (gallons per minute) it can heat at one time compared to a warmer climate. When sized properly this water heater will provide endless hot water and only consume the energy needed, giving the user complete control. Prior to purchase and installation please verify this model is the right size for the expected demand and electrical requirements. The ECO 11 requires a minimum 125 amp electrical panel for installation with 60 amp double pole breaker connected to set of #6 awg wire. Plumbing connections are 1/2" compression fitting with the option of 1/2" NPT adapter included. For additional assistance please feel free to contact our support center at 877-474-6473.



NOTE : 11Kw at 220 is equal to 13kw at 240. .Activation Flow : 0.3 GPM

From the Manufacturer

This Smart Technology electric tankless water heater is configured for climates where incoming water temperature is 67 Degree F and above. This model is well suited for heating up to 2-Gallon per minute, which is the equivalent of one shower head (with a 1.5 gpm flow) and one sink with a low inlet water temperature of 67 Degree F. Digital Temperature Control allows you to set your temperature in increments of 1 Degree. This model can also be used in colder climates as a Point of Use for a sink or other low flow application. Prior to purchase and installation please verify this model is the rights size for your hot water needs and electrical requirements.

• Lifetime warranty
• Save up to 60-percent on your water heating cost with an ECOSMART electric tankless water heater
• Never run out of hot water with an ECOSMART tankless water heater
• Patented Self Modulating Technology and design
• ECOSMART tankless water heaters are 99.8-percent energy efficient.Uniform Energy Factor:0.98

User questions & answers

Question:	Ours has only been in service for less than a year - will not adjust temperature to anything above 85 Deg. F. What do you think is the problem ? kds
Answer:	My only guess is that the rheostat (variable resistor) that the temperature adjustment knob is attached to may be faulty. If that isn't it then I don't know. Sorry.
Question:	The warrenty says that this unit must be installed by a licensed electrician and plumber, for them to honor the "life time warrenty." why
Answer:	Hello Bob, The reason is the same as why an innumerable number of gadgets around the world have that little "warranty void if removed" label. Because getting inside of one requires a certain level of training and expertise. Same with this unit. GadgetsGo is an authorized Ecosmart dealer. Kind regards,HenryGadgetsGo
Question:	My house is wired 110V. What additional items do I need to purchase for the conversion
Answer:	Just to expand slightly on prior answers, normally a residential service feed is 240 volts between the two incoming hot legs. There is also a neutral leg, which (hopefully) has zero potential with reference to ground. The voltage between either one of the hot legs and the neutral leg is 120 volts. The 120 volt circuits in your house are connected to one or the other of the two hot legs, and only one. An attempt is made to assign circuits to the two hot legs in a way that will roughly balance the load between them. The other side of a 120 volt circuit is connected to the neutral leg. There is additionally a safety ground run with the circuit, which also ties into the panel. Certain devices require more power (work product of current and voltage) than is practical to deliver using a 120 volt circuit. Common examples are your clothes dryer, and your electric stove. These devices are powered by both hot legs, with a difference in potential of 240 volts. This water heater is also such a device.STRONG BUT FRIENDLY WARNING: If you did not already know this, please don't make wiring this water heater your learning opportunity with electricity. Hire someone who knows how to do it right. Cutting corners, especially with higher currents and voltages, can lead to equipment damage, fire, and electrocution. Electricity is not magic, and you can certainly learn how to do many common wiring tasks safely on your own, but today is not the day to begin that journey. You need properly sized components, properly installed, and connected to an adequate service. Also, if you really, really foul up, you could conceivably wind up making that morning shower more energizing than you ever imagined, if you get what I mean. So newly aspiring electricians should go fix their grandmother's favorite table lamp instead. Once they have that working they can use it to to start reading books about electricity, residential wiring, and eventually, books about this stuff: http://amazon.com/s/ref=nb_sb_ss_c_0_8?url=search-alias%3Dstripbooks&field-keywords=nec+code&sprefix=nec+code%2Caps%2C164 . Of course, you still have to know not to nick conductors when you strip them, and other trade craft like that ; ) . Like almost everything in life that is fun, electricity will hurt you. Sort of like all those people you dated for a while, and then wished later you had never met.
Question:	what amp breaker is required
Answer:	The National Electrical Code requires conductors and overcurrent protection to be sized at 100% of the manufacturer's branch circuit recommendation for tankless electric water heaters. A 60 amp breaker is the same price as a 40 or 50, it is the wire that costs more. #6 AWG wire is required for a 60 amp circuit. If you undersize the wire it could overheat and catch fire. Protect your family and follow the manufacturer's sizing for this, or any other, electrical device. Your family's lives are worth the extra money. 

Product features

3 Smart Steps for Endless Hot Water

Step 1: Determining your average inlet water temperature is important, this allows you to determine how well your unit will perform in your desired location. A lower inlet water temperature will require a higher kilowatt product.

Step 2: Next you will determine how many applications your unit can run simultaneously at your chosen location inlet water temperature. Tankless electric water heaters are sized for maximum simultaneous use, not maximum fixtures in your home.

Step 3: Determining specifications and electrical infrastructure is important because without the correct infrastructure your unit may not fit into your breaker panel.

• WIDE AIR DISTRIBUTION: The celling heater is constructed in a fan-forced air design with adjustable directed airflow vents that provide superior heat distribution across a wide area.
• DIGITAL CONTROL: With its integrated digital thermostat control, 12-hour timer and remote controller, the 10,000-watt space heater allows you to set the optimum temperature for efficient heat output.
• QUALITY CONSTRUCTION: The industrial heater has a heavy-gauge steel body for durability. Heating elements are fully sheathed and the motor is enclosed for increased protection in dusty environments.
• HARDWIRE INSTALLATION: The ceiling-mount heater comes complete with an adjustable mounting bracket for optimized positioning. It requires a single-phase hardwire connection (240 Volt A.C.) for installation.
• SAFETY PERFORMANCE: Power and caution indicator lights allow you to easily monitor operations, and the overload switch on this industrial heater provides added protection.

User questions & answers

Question:	Is this 3 phase
Answer:	No It is not 3 phase, but it is 220 volts and not 115 volts, to wire it it needs two hot wires and a ground, I said ground, being AC current the two hot wires alternately act as a neutral. With 115 volts you would need one hot wire, one neutral wire, and a ground wire. This furnace will work on 220 volts only.
Question:	What's the BTU output
Answer:	Manual says 21,311 to 25,589 BTU per hour.
Question:	I have a 28x32 garage with 10 foot ceilings. Side walls are insulated and drywalled and ceilings are just drywalled. With this work in there
Answer:	I have this heater in my garage which is 40 x 30 feet with 12 foot ceiling. The walls are cement block which are sand insulated.this heater does a great job in my garage. It heats up quickly and well controlled heat temps. Would not trade it for any other kind of heat or heater. I give it a high rating and am a very satisfied customer.
Question:	How many amp service breaker does this need ? Is 20 Amp service okay
Answer:	This is not a subject of opinion; it is a very specific matter, lest one burn to death in a fire. Whatever or whomever suggests anything else, is dead wrong! Ohm's Law is a fundamental law of physics, and the NEC governs everything! Amperage is calculated by dividing Wattage of the appliance by manufacturer's stated Voltage supply. Period. Street voltage can run from 220 to 240, so always go with the higher, and the current must never exceed the breaker, or it will do its job and break to prevent overload. 10,000 Watts divided by 240 Volts equals 41.6 Amps. This unit requires a 50 Amp breaker. Wire size is determined by load, length and material of the conductor. #6 AWG copper or #4 AWG will serve up to 165 feet with an NEC maximum allowance of 3% voltage drop from the source. A longer run will require #4 and #3 respectively. One CANNOT use any such thing as a 30 Amp or 40 Amp conductor or breaker!

Product features

Digital Temperature Control

Easily adjust the temperature on this 10,000-watt space heater using the integrated digital thermostat control. You can achieve efficient heat output and custom heating levels to suit yourself and your environment. The remote control is easy to operate and the 12-hour timer offers added convenience.

Durable Industrial Heater

The versatile ETL-compliant, 208/240-volt space heater is an ideal choice for use as an electric garage heater, electric shop heater or commercial heater. It features a heavy-gauge steel body and fully sheathed heating elements for durability and lasting performance in any setting. The motor is fully enclosed provide added protection in dusty settings.

Hardwired Ceiling Mounted Design

The mounting bracket included with this ceiling-mount heater can be adjusted to optimize positioning. The space heater requires a single-phased hardwired connection for installation.

Easy and Safe Operation

The space heater conforms to OSHA and NEC requirements, and it features power and caution indicator lights for easy operation and monitoring. An overload switch provides added safety and protection against electrical overload.

• SPACE-SAVING DESIGN: The fan-forced heater is designed for ceiling mounting and hard-wired installation, which saves valuable floor space in a packed warehouse, garage or storage area.
• DURABLE STEEL CONSTRUCTION: The body of the commercial heater is crafted from heavy gauge steel, which stands up well to the temperature fluctuations in areas that are poorly insulated.
• TARGETED HEATING: Louvers and a variable mounting angle direct airflow where it is needed most, while the fan-forced design helps to distribute it throughout the room.
• CONVENIENT CONTROLS: The digital thermostat allows you to adjust the temperature to just the right level for your space, while a remote control makes it easy to change the settings from a distance.
• OVERHEAT PROTECTION SENSOR: A built-in sensor detects when the ceiling mount heater has overheated on the inside and switches it off automatically to help prevent damage to the unit.

User questions & answers

Question:	Does the white room temp sensor go in ntc or ntc1 on board
Answer:	Call the company
Question:	I have a wood working shop. Would dust be problem for this heater
Answer:	This heater has hot and arcing parts inside and could be a fire hazard in a woodworking shop if placed in an area with a lot of wood dust.
Question:	What sqare footege is this ideal for
Answer:	I have a 20x30x10h shop. Lots of windows coverage. Non insulated floors above open front20x30x8 area. On a 30 degree day with help of a overhead fan it get up to 60. But must have a fan to move the air or I notice the area around heater warms up and shuts fan off early. Have heard about the temp wire being moved outside of heater may try that. Once the max temp you set is reached it does want to cycle on and off constantly. I just turn it off. It’s extremely nice to have. I haven’t seen a electric bill yet or used it more than a couple of hours aday. It’s definitely a 8 guage wire and 40 amp install. Im happy .
Question:	What is the lowest temperature setting
Answer:	45

Product features

Rugged Construction

Designed for extended use in harsh environments, this fan-forced heater is crafted with a tough, heavy gauge steel body. This allows it to stand up to the sudden temperature drops and spikes it will encounter in poorly insulated areas. The motor is fully enclosed to help keep it running smoothly, even during extended use in dusty work spaces.

Target Heat

Louvers and a variable mounting angle allow you to aim the airflow towards a drafty area or towards your usual workstation, ensuring that the warmth goes where it's needed most.

Easy Digital Controls

A digital thermostat allows you to adjust the heat precisely to your deisred temperature, while a 12-hour timer allows you to run it for a set amount of time instead of switching it on and off manually. A full-function remote control is included to allow you to easily adjust the 240 Volt commercial heater's settings from a distance, so you can turn it on and off or raise and lower the temperature as needed without leaving your desk.

Overheat Protection Sensor

A sensor automatically turns the ceiling mount heater off whenever it reaches an unsafe temperature, helping to prevent damage to the unit.

Product description

The DR988A industrial electric garage heater is perfect for warming any construction site, garage, basement, and workshop with its specially designed heating element and features an impressive portable design. It comes with a built in thermostat that can be adjusted from low to high. It also features a fan that provides continuous warmth. The DR988A industrial heater is dependable and sturdy.

• Auto Overheat Cut-Off Protection
• Temperature Range: 45-95 degrees F
• Comes with Thermostat control. Wattage: 5600W. Volts: 240V/ 208V
• UL and C-UL listed
• Noise level at 45 dB
• Power Cord: NEMA#6-30P (receptacle NeMA #6-30R 250V 30 Amps)
• *Special Outlet Required

User questions & answers

Question:	Does this heater have an enclosed motor
Answer:	made in china!
Question:	What is the male plug type on cord
Answer:	we don't sell filter on line! but our filter is good quality and you just need to wash and clean on it and continue to use! if you really need one, please let me know ! have a nice day!
Question:	The profile says "....not for general residential or household use"? i had a nema 6-30 plug installed for a heater. i've also looked a the cadet
Answer:	no need to change the filter
Question:	Does this have a 3-prong (L-shapped ground) wall plug,same type as my electric dryer uses? If not, how do I adapt? Any idea other heater that does
Answer:	no need to buy filter! you just take the filter out and clean it and put it back! this filter is high quality!
Question:	Are these made in the USA
Answer:	So i gave this product a bad review. for the amount of good rating this had i expected this to really cool my room. i sleep with it a foot away from me it does the job. and no it dosnt do anything to the water.
Question:	How do I order a replacement filter
Answer:	Mine appears to run continuous. There not an automatic on and switch when it's out of water....
Question:	Do you have to change the filter
Answer:	Regular US outlet- my son loves it. We put ice cubes in it- cools great for a small room.
Question:	Where do I buy the filter for the home cooler
Answer:	It will not. The best it does is cool an individual person as long as they are sitting no more than a foot in front of it. We had it in a small bedroom and it was a waste of my time and money.

Product features

Dr. Infrared Heater DR-988A Garage Shop 208/240V, 4800/5600W Heater with 6-30R Plug

The DR988A industrial electric garage heater is perfect for warming any construction site, garage, basement, and workshop with its specially designed heating element and features an impressive portable design. It comes with a built in thermostat that can be adjusted from low to high. It also features a fan that provides continuous warmth. The DR988A industrial heater is dependable and sturdy. Build-in cord storage helps keep your space tidy. Safety features include finger-proof intake and discharge grills and a high temperature heating limit. For quick, safe, and efficient heating, choose the DR988A, and you will never be left out in the cold.

Auto Energy Saving Model

Built in thermostat that can be adjusted from HIGH to LOW. Set your preferred temperature, the heater will automatically maintains the proper temperature you set.

Convenient & Safe Features

Electronic Thermostat: 45-95 deg. Overheat protection. Finger-proof intake and discharge grills.

Designed For Workspaces

Comes with built-in carry handle with maximum portability. High temperature heating limit for safety.

Advanced Dual Heating

Heat up a large room fast and evenly - without hot spots and cold spots

Product description

Need safe, comfort and quick heat? This DR966 3000/6000W industrial heater can be easily installed in either your new or remodeled building. Dr966 can be your primary or auxiliary heat source for your garage, factories, stores, warehouses, workshops, schools, churches, hospitals, dormitories or any exposed areas. DR966 uses spiral steel metal sheath electric heating elements with low sheath temperatures provide uniform heat and long service life. Plus a large, matched, dynamically 8" fan provide maximum air flow with minimum turbulence and noise, gently distributes warmth through your area. Totally enclosed, thermally protected, heavy duty ball bearing motor features permanently lubricated provides long life and low maintenance. Built-in adjustable thermostat allows to set your desire style. Rugged stamped steel front cover with five-way adjustable louvers for easy control airflow. Ceiling and wall mounting bracket are included. Finished in a gray epoxy paint. UL & CUL Listed. 1 Year parts and labor Warranty.

• Heavy Duty 240V Single Phase 3000/6000W Commercial Electric Heater
• Hardwired; Power cord not included in the unit. Dimensions: Overall Height - Top to Bottom: -14.5". Overall Width - Side to Side: -13". Overall Depth - Front to Back: -14.5".
• UL/CUL Listed Wall or Ceiling Mounted Heater; Bracket Included
• Adjustable Thermostat with HIGH and LOW Setting. A dynamically 8 inch fan provide maximum air flow with minimum turbulence and noise, gently distributes warmth through your area
• 5 Adjustable Louvers for to Direct Airflow

User questions & answers

Question:	how many btu's is this unit
Answer:	On high, the unit operates at ~6000 watts. This equates to 20,472 btu/hr. This assumes 100% electrical efficiency. A solid assumption would be 20k btu. (1 BTU = 0.00029307107017 kWh)
Question:	How many BTUs will this heater provide? How many amps will it draw
Answer:	The BTU is 20,500 and at HIGH, this heater draws 25 amps
Question:	Can this unit be used with an in line thermostat? i.e. will it come on when power is supplied to it
Answer:	Yes if you can find one with the right amperage rating. I used a two pole contactor and used a 120v 20 amp thermostat as the switch
Question:	What is the largest space/area in sq-ft that it can heat at full power? Can't find this info anywhere
Answer:	My shop is 30ft x 30ft well insulated I North Ms. I will get it up to 60+ deg easy in 30-40 deg winter which is comfortable to work in, so I does what I expected. My main purpose was to have it set to keep shop above freezing and not have a heater on the floor. I set it for around 45. Did not notice a huge jump in power bill. Hope this helps.

Product features

Dr. Infrared Heater DR-966 240-volt Hardwired Shop Garage Commercial Heater, 3000-watt/6000-watt

Need safe, comfort and quick heat? This DR966 3000/6000W industrial heater can be easily installed in either your new or remodeled building. Dr966 can be your primary or auxiliary heat source for your garage, factories, stores, warehouses, workshops, schools, churches, hospitals, dormitories or any exposed areas. DR966 uses spiral steel metal sheath electric heating elements with low sheath temperatures provide uniform heat and long service life. Plus a large, matched, dynamically 8" fan provide maximum air flow with minimum turbulence and noise, gently distributes warmth through your area.

Totally enclosed, thermally protected, heavy duty ball bearing motor features permanently lubricated provides long life and low maintenance. Built-in adjustable thermostat allows to set your desire style.

Rugged stamped steel front cover with five-way adjustable louvers for easy control airflow. Ceiling and wall mounting bracket are included. Finished in a gray epoxy paint.

Product description

Need safe, comfortable, quick heater. Infrared heater DR-975 heavy-duty hardwired shop garage heater can be easily installed in your new or remodeled building. This 7500W heater can be the primary or auxiliary heat source ideally suited for use in garages, factories, stores, warehouses, workshops, Schools, churches, hospitals, dormitories, or any exposed spaces. The DR-975 uses spiral steel metal sheath electric heating elements with low sheath temperatures, providing uniform heat and long lasting product life. Additionally, a large, matched, dynamic fan provides maximum air flow with minimum Turbulence and noise, gently distributing warmth throughout your space. The heavy duty ball bearing motor is totally enclosed, thermally protected, and permanently lubricated, requiring minimal maintenance. Built-in adjustable remote-controlled thermostat allows you to set your desired temperature between 50 - 90 degrees. If desired, an optional wall-mounted external thermostat can be wired to this heater (sold separately, does not come with heater). rugged stamped steel front cover features five adjustable louvers for easy airflow control. Can be mounted on either the wall or ceiling (bracket included). finished in a grey epoxy paint. Ul & CUL listed. 1 year parts and labor warranty.

• Heavy duty 240V single Phase 4700/7500W electric heater
• Hardwired, wall/ceiling-mounted heater
• Remote controlled thermostat with temperature range from 50 - 90 degree
• 5 adjustable louvers to direct airflow
• UL/CUL listed; timer feature; heavy duty fully enclosed motor

User questions & answers

Question:	Can this sit on concrete
Answer:	The air flows in through the back and out the front. I do not see any reason you could not sit this on concrete. I would not sit it on anything but concrete because it gets pretty hot.
Question:	DR-975 power on - bad instructions Heater does not turn on after power interruption like instruction say it will. Any workaround from using remote
Answer:	Yeah I returned my DR-975. It doesn't turn on when power is applied to it, so any automated system that powers it on a schedule will not work. You have to use the remote to turn it on manually. Also my interior thermostat wasn't working, when I switched to wall thermostat it would work just fine--even no wall thermostat was installed. So I don't know what's going on there. I just bought the 966 again since on Home Depot it's actually advertised at 1000sqft heating capacity.
Question:	Were can i get a remote for this unit
Answer:	This unit comes with remote control...
Question:	Unit only displays “lo” not air temperature. doesn’t respond to up or down on the remote. internal thermostat only. what’s up
Answer:	Your unit appears to have a defective temp sensor. Please contact support at 800.317.1688.

Product features

Dr Infrared Heater DR-975

Need safe, comfortable, quick heat? Dr. Infrared Heater DR-975 Heavy-Duty Hardwired Shop Garage Heater can be easily installed in your new or remodeled building. This 7500W heater can be the primary or auxiliary heat source ideally suited for use in garages, factories, stores, warehouses, workshops, schools, churches, hospitals, dormitories, or any exposed spaces. The DR-975 uses spiral steel metal sheath electric heating elements with low sheath temperatures, providing uniform heat and long lasting product life. Additionally, a large, matched, dynamic fan provides maximum air flow with minimum turbulence and noise, gently distributing warmth throughout your space.

• SPACE-SAVING DESIGN: The fan-forced heater is designed for ceiling mounting and hard-wired installation, which saves valuable floor space in a packed warehouse, garage or storage area.
• DURABLE STEEL CONSTRUCTION: The body of the commercial heater is crafted from heavy gauge steel, which stands up well to the temperature fluctuations in areas that are poorly insulated.
• TARGETED HEATING: Louvers and a variable mounting angle direct airflow where it is needed most, while the fan-forced design helps to distribute it throughout the room.
• CONVENIENT CONTROLS: The dual knob thermostat allows you to easily adjust the temperature to just the right level for your space and to turn the ceiling mount heater on and off quickly.
• SMART SAFETY FEATURES: A built-in sensor switches the device off automatically if it overheats, while a power indicator light ensures that you know when the unit is in use.

User questions & answers

Question:	I need an operation manual
Answer:	try looking here: https://www.princessauto.com/hlr-system/Documents/84/843/8436/8436834_manual.pdf
Question:	What's the lowest temperature this will hold
Answer:	There’s no way anyone can give a definitive answer to that. If you put this little unit in a massive warehouse that’s not insulated. And it’s -15 degrees F outside. It likely won’t hold any temp. There’s lots of factors.
Question:	Does the "Power" indicator light stay on continuously or only when the heater is functioning? Mine is on continuously even when not running
Answer:	Mine (Yellow Indicator) went out after 1 month. Heater works fine but no more yellow light.
Question:	Where is this heater made
Answer:	Not sure - But, this might help: As a leader in safety and reliability, Comfort Zone products are designed and tested to meet strict global quality standards including UL, ETL, SAA, CE, CSA and NOM.

Product features

Rugged Steel Construction

Designed for extended use in harsh environments, this fan-forced heater is crafted with a tough heavy gauge steel body. This allows it to stand up to sudden temperature drops and spikes it can encounter in poorly insulated areas.

Targeted Heating

Louvers and a variable mounting angle allow you to aim the 240 Volt commercial heater's airflow towards a drafty area or towards your usual workstation, ensuring that the warmth goes where it's needed most.

Simple Manual Controls

The heater features a dual knob at the front that allows you to quickly and easily adjust the thermostat or turn the unit on and off. The simple controls make it a snap to get the heat output to just the right level for your space.

Smart Safety Features

A built-in sensor immediately shuts the fan-forced ceiling mount heater off if it reaches an unsafe temperature to prevent overheating. The unit also features a power light that clearly indicates when it's in use, helping you to ensure that it's safely turned off before you leave the room.

Product description

Heating large, drafty spaces can be difficult to say the least. The Fahrenheat FUH Electric Heater offers an easy and effective way to provide lasting, comfortable warmth in even the most hard-to-heat areas. Suitable for indoor spaces as well as several outdoor spaces, this heater mounts easily to the wall; it provides warmth in home spaces as well as commercial spaces. It comes with a remote control to easily operate from a distance. It works smart; the automatic control delays fan use until the heating element is warmed. For added safety and durability, when the heater is at maximum capacity or turned off, the fan continues to operate until the heating element is cooled. By preventing the circulation of cold air and preventing an output of an excessive amount of heat, your space stays comfortable longer. Fahrenheat is part of the Marley Engineered Products family, which provides a wide range of innovative, quality engineered, commercial, industrial, and residential electric comfort heaters and ventilation solutions. All our products are engineered with aesthetics, functionality, safety, and structural tolerance in mind.

• HEAVY DUTY HEATER: Warm-up just about any open space with this heater that provides long-term comfort solutions with its built-in single pole thermostat that adjusts from 45 to 135 degrees Fahrenheit.
• CONTINUOUS COMFORT: If you have a large drafty space, this heater is ideal. Its powerful output means it can warm cold commercial areas, stores, service stations, spacious basements, and even outdoor areas like patios and workspaces.
• EASY TO USE: This heater includes a ceiling mounting bracket for vertical or horizontal mounting, or any position that suits your space. It has adjustable louvers, so you can aim your heat directly toward your desired area and change as needed.
• OUTPUT CONTROL: The high-level cutout automatically shuts off to prevent overheating and reactivates the heater when the temperature returns to normal. The built-in thermostat allows you to set your heat level to deliver as much warmth as you need.
• COMPATIBILITY: Whether you need 208 or 240 volts, this heater is fully compatible with your electrical system.
• Wattage: 5000 Watts

User questions & answers

Question:	Will this work on a single 20 amp breaker
Answer:	No. The bulbs are very hot and would likely shatter if splashed. You can have them in a bathroom outside the shower or tub where they'd shine on you while your're toweling off, but not directly over the ub.
Question:	will this heater work with a wall mount thermostat and if so which one
Answer:	No. A tag inside the unit says "max 250W" The red infrared 250w bulbs may give off more heat than the white bulbs.
Question:	What does the 2500- 5000 watt mean? Which is it? And is this unit noisy when blowing? thank you
Answer:	I would not recommend installing this anywhere that a drop of water could splash or spray on the hot bulbs which are exposed. better to install outside of the shower enclosure, in an area that remains dry and protected from overspray.
Question:	What has the increase to your electricity bill been like
Answer:	Yes, in fact it is wired for that and the instructions describe how to wire it both ways: with 2 heat lamps (controlled by one switch), or with one heat and one illumination lamp (using two separate switches). It has a tiny fan and that is designed to be wired so it runs when the heat lamp (either 1 or 2) is on.

Product description

Quickly heat up any garage or workshop, and keep it warm with the NewAir G56 5600 watt garage heater. This heater features a durable stainless steel construction, and it has the power to warm up to 560 square feet quickly and efficiently. Certified for electrical safety, this NewAir garage heater has a fully protected motor and a steel safety grille to keep hands and fingers from harm. A sophisticated thermal cut-off system ensures the unit turns off if it starts to overheat. Take this heater wherever you need extra warmth. The NewAir G56 garage heater has a 3-pronged, 240V plug, 6-foot cord, built-in carrying handle, and sits right on the floor, so finding a place to set it up is easy. The NewAir G56 5600 watt garage heater features a reliable single-pole thermostat that automatically maintains the temperature you set. Get all the heat you need just by turning the dial.

• [POWERFUL FAN FORCED HEATING] - With 5,600 watts of heating power, this electric garage heater packs a punch. It's strong enough to warm up to 600 square feet—perfect for a two-car garage or a 24x24 workshop or shed.
• [RUGGED EXTERIOR BUILT TO LAST] - Black powder coated finish protects against scratches and scuffs, making this sturdy steel-bodied heater perfect for garages, workshops and light industrial environments.
• [THERMOSTAT & AUTO-FAN TEMP CONTROL] - Set the temperature you want. Once the space has reached the ideal temperature, the fan will automatically kick-in as needed to keep your workshop warm. It’s that easy to get the heated working environment you need in winter.
• [PORTABILITY FEATURES FOR FAR-RANGING HEAT] - Take advantage of 2 portable features: the cord wrap and carry handle. Together they make it easy for you to position or move your heater to the most ideal place in your garage, workshop, or shed.
• [SAFETY FEATURES FOR PEACE OF MIND] - This UL-certified heater has an automatic shut-off function that prevents overheating. The outer construction stays cool after use to ensure safety for you and your space.

User questions & answers

Question:	Does it require 220/240 power only
Answer:	Yes, this requires 240 volts and 30 amps.
Question:	Are the heating coils supposed to glow red? Taken me 1hr to go 45 to 55deg; a reviewer said he went same in 10min
Answer:	No, the coils do not glow like a toaster. You are not giving enough info to determine if heater is working properly. It is possible you are expecting to much. Most 120 volt space heaters are rated at 1500 watts. This heater produced less than 4 times that. It is convenient that all that heat comes from one heater but it is still not a lot of heat.
Question:	Can I use this on a 20amp circuit
Answer:	Unit drawers around 25 aAmps. Would trip a 20 amp breaker. I have mine plugged into a 30 amp 220 volt dryer circuit.
Question:	What is the amp rating on this
Answer:	I think it's rated 'mid-20's'... we have a 30-amp service and it works fine.Great heater, highly recommend!!

Product features

NewAir G56 5600 Watt Electric Garage Heater

When you need heat fast, turn on the NewAir G56 5600 watt garage heater. Powerful enough to heat up to 560 square feet, this sturdy steel-bodied heater is perfect for garages, workshops and light industrial environments.

Largest Coverage Area

With a 5600 watt heating capability, the NewAir G56 garage heater can heat large areas up to 560 square feet - making it our most powerful electric garage heater available.

Rugged, Portable Design

Wherever you need extra warmth, the NewAir G56 garage heater is ready to deliver. It sits right on the floor, so finding a place to set it up is easy. The built-in carrying handle with cord storage makes it easy to take along.

Easy-to-Use Temperature Control

The NewAir G56 5600 watt garage heater features a reliable single-pole thermostat that automatically maintains the temperature you set. Get all the heat you need just by turning the dial.

Plug Type

The NewAir G56 5600 watt garage heater has a 6-30P plug and requires a 6-30R recepticle in order to operate.

Product description

The Comfort Zone 7,500-watt wall-mount heater is perfect for industrial settings or your garage. It features thermostat control, fan-forced for wide area circulation and adjustable louvers to direct output. It features a heavy-gauge steel body, power and caution indicator lights and fully enclosed motor for use in harsh conditions. Comfort Zone is driven to perfection producing quality products for everyday living.

• 2 heat levels up to 7,500W
• Thermostat control
• Fan-forced for wide heat dispersion
• Ideal for household use
• 208V-240v heavy-duty, high-output heater

User questions & answers

Question:	How low can the thermostat be set to control
Answer:	The thermostat on the heater is marked off, low and high. You can set it anywhere you want from off to high. I turn it until it comes on, let it run and adjust it up or down as needed. It works great, keeps my 1000 sf uninsulated garage around 50 degrees in below freezing temps.
Question:	How many amps will this 7500w unit draw? Breaker and wire size
Answer:	To find amps , divide watts (7500) by the voltage (240 , that's what 2 phases in your house is.) that equals 31.25 amps. so use # 8 wire on a 2 pole 40 amp breaker. You can't use a 30 amp breaker on anything that draws more than 30 amps . It may not trip , but it's not legal , or safe.
Question:	Can i hook two of these to one 60 amp breaker
Answer:	No. There is more to this. The unit is rated at 32 amps 240 but starting amps is much higher. This unit requires a 45 amp breaker and pulls about 38 amps when it starts on high and levels out at 31.8 for the one I have. You must run 8 gauge wire on a 240 line with no neutral.
Question:	is this unit loud
Answer:	It sounds like a box fan set on medium.

Product description

The PGH is a high wattage portable heater desigend to provide a back-up heating source at an affordable price. Perfectly suited for the workshop, garage or construction sites, the rotation capability. The convenient 6 foot cord allows greater mobility to areas needing heating, while the handle serves as a reel for the cord when not in use. Easily set the desired temperature with the built-in thermostat. Sure stop high-limit temperature control with auto-reset provides overheat protection.

• 240 Volt--4000W utility heater
• Built-in thermostat and On/Off rocker switch
• Power indicator light; Built-In Fan Delay To Dissipate Heat
• Durable scratch and rust resistant finish
• Stainless steel tubular heating element

User questions & answers

Question:	Can this be mounted on a wall
Answer:	This can be mounted on the ceiling or wall with the included bracket.
Question:	can this heater by used inside the house...bedrooms? bathrooms
Answer:	Yes, but don't forget it is a 220 volt heater and very few people have 220 volt receptacles in a bedroom or bathroom.
Question:	Can it heat small room (16×16) to 120 degrees
Answer:	The heater will heat an area up to 400 sq feet. A built-in thermostat allows you to maintain a comfortable working temperature, from 45 to 85°F.
Question:	Got one for Christmas and honestly can't feel air moving two feet in front of it. Is this normal? Fan is running
Answer:	The fan is rated at 300 CFM and should be putting out more air than that. Check to be sure you have is plugged into a 240 volt receptacle not a 120 volt.

Product features

Portable Comfort For Your Garage

240-Volt Portable Electric Garage Heater With Thermostat.

A rugged portable heater in designed to provide a high capacity heating source perfectly suited for workshops, garages or enclosed construction sites. The flow-through design efficiently moves air by pulling air from the back and discharges it out the front, easily heating a large space. Offering a SureStop high temperature-limit.

Safe Comfort for the Garage

The SureStop high temperature-limit features shuts power off to the heater in an abnormal event, providing protection from overheating.

Rugged Portable Construction

Durable scratch and rust resistant finish

Includes Wall/Ceiling Mount Bracket

Convert to a permanently mounted plug-in style heater with the included wall/ceiling bracket.

More Reasons to Choose

Ideal for temporary heating of your shop or garage.

Heats up to 450 square feet.

With 6-Ft Cord -20A Plug for portability.

Peace of Mind—includes SureStop high temperature-limit.

Fan delay increases efficiency dissipating heat from the elements during cool down.

Built-in adjustable thermostat.

Universal wall/ceiling mounting bracket.

Durable, easy to use, and high quality.

1-year warranty.

ETL certified to USA and Canada standards.

Product description

A048 Portable Space Heater for Garage, Industrial Fan Forced Heater,4800 Watt , 240 Volt, 60Hz



Fan forced heat for fast heat distribution.

Grounded 3 prong NEMA connector for safety

With 4800 watts, this heater is suitable for your garage, shop, or warehouse, and is powerful enough to keep you warm while working in cold weather.



This heater can be the primary or auxiliary heat source ideally suited for use in garages, factories, stores, warehouses, workshops, schools, churches, hospitals, dormitories, or any exposed spaces.



This heater can be mounted on either the wall or ceiling.



Easy Storage

Built in cord storage makes clean-up easy, and storage a breeze.



Simply Plug-In and Go

Includes 6 foot cord with NEMA #6-30P 30Amps standard plug, simply plug into a 240 Volt Socket, and begin heating your space.

• Convenient and Portable : No need to heat the entire garage, simply move the heater to where you need it. Built with a convenient top carrying handle for portability.
• High Performance: Internal fan provides superior heat distribution across a wide area.
• High Quality: Manufactured from sturdy steel with black powder coat finish, rubber feet for stability, and a handy carry handle.
• Designed for Safety: The overheat protection system shuts the heater off when the unit becomes too hot. Grounded connection to help prevent electric shock.
• Thermostat Control: Turn the dial to set the temperature and adjust to your personal comfort.

Product features

AA048 Industrial Fan Forced Heater,4800 Watt , 240 Volt, 60Hz

Industrial Fan Forced Heater

Fast heating unit will quickly warm your area.

Powerful fan to distribute the heat, this sturdy steel-bodied heater is for garages, workshops and light industrial environments.

240V voltage

60 Hz frequency

4800 Watt

NEMA #6-30P 250C 30 Amps plug

ETU 16400

Temperature Control

Temperature Control Reliable single-pole thermostat with adjustable heat control dial, automatically maintains the temperature you set.

Large Coverage Area

Large Coverage Area With a 4800 watt heating capability, this unit can heat large areas quickly, making it our most powerful electric garage heater available.

Carry Handle

Convenient handle allows you to carry this fan anywhere you need it, could also be used to hang for storage.

Product description

Stiebel Eltron CK 20E (208-240V) Wall Mounted Electric Fan Heater, 208-240 VoltsStiebel Eltron CK 20E (208-240V) Wall Mounted Electric Fan Heater, 208-240 Volts is ideal for bathrooms, kitchens, hallways, and any location where quick heat is needed. They feature surface-mount design with quick, easy installation, and can be installed over existing outdated heaters. They have a unique design that enhances decor. The compact design fits almost anywhere, and the downdraft design eliminates cold floors. The features also include quiet operation, built in thermostat, and quality construction. The Stiebel Eltron CK 20E electric wall mounted heater is a sleek alternative to conventional electric space or recessed heaters and provides quick heat in just about any location. It can be mounted anywhere in the house and has a new design to effectively and efficiently disburse heat throughout the general area. At 240 volts it produces 2000 watts of heat with a fan to help improve heat transfer. Stiebel Eltron CK 20E (208-240V) Wall Mounted Electric Fan Heater, 208 Volts Specifications: 208 Volt 7.2 Amps 1.5 KW 15 Amp circuit breaker 14 AWG in. supply wire gauge Heating element: Nichrome Wire Thermostat: Bimetal type High limit: Bimetal type Motor: 18 Watt shaded pole Blower: Galvanized steel, squirrel cage type Height x Width x Depth: 18 1/8" x 13 1/4" x 4 3/4"; 460mm x 335mm x 123mm Housing: Painted steel/plastic Model: CK20E Stiebel Eltron CK 20E (208-240V) Wall Mounted Electric Fan Heater, 240 Volts Specifications: 240 Volt 7.5 Amps 2.0 kW 15 Amp circuit breaker 14 AWG in. supply wire gauge Heating element: Nichrome Wire Thermostat: Bimetal type High limit: Bimetal type Motor: 18 Watt shaded pole Blower: Galvanized steel, squirrel cage type Height x Width x Depth: 18 1/8" x 13 1/4" x 4 3/4"; 460mm x 335mm x 123mm Model: CK20E Housing: Painted steel/plastic

From the Manufacturer

Stiebel Eltron CK 20E Wall Mounted Electric Fan Heater-240V/2000 watts offers and exciting room heating alternative for new construction and renovation projects. This unit is an ideal replacement for recess-mount heaters.

• Surface mount design
• Quality construction
• Quiet operation
• Built in thermostat for maximum comfort
• Reliable performance

User questions & answers

Question:	Can this be mounted high instead of low on the wall? Would higher be a safety issue? I need a heater for my toddler's room that he cannot get to
Answer:	Yes, the model H4810 is BPA free. If you need additional assistance, please contact [email protected] or call 1-866-603-5900
Question:	How much airflow is there? i cannot find a cfm rating.... help
Answer:	Yes, you can see through the tank to see where the water level is. If further assistance is needed please contact us at [email protected] or at 866-603-5900 X213 M-F 8:30-4:30 EST.
Question:	what is the maximum room size for one unit
Answer:	You can change the mist output to low, medium or high. This unit does not offer the capability to set a certain percentage. If further assistance is needed please contact us at [email protected] or at 866-603-5900 X213 M-F 8:30-4:30 EST.
Question:	I have an old (and utterly useless) 220v baseboard I was thinking of replacing with this. What is the advantage of 220v over
Answer:	In winter of January 2018 we used only Distilled Water and had NO WHITE DUST PROBLEM. In winter of Dec. 2018 to Mar. 2019, we used only Tap Water and had a white film appear on every vinyl surface and shelf surface in the two Bedroom apartment - even on vinyl CD cases inside a binder.

Product features

Made in Germany

All CK heaters are made by us in our factory in Germany. We pride ourselves on a reputation for engineering & manufacturing excellence since 1924.

Ultra quiet fan

CK and CKT heaters have galvanized steel, squirrel cage type blowers that operate at a quiet 49.7 dB(a). The glass-reinforced poly-carbonate, radial type blower in CK Trend heaters operates at an even quieter 49 dB(a).

Even-heating down-draft design

CK and CKT heaters pull in cool room air from the top and blow warm air out the bottom. This down-draft design helps to evenly heat a space for maximum comfort.

Stand-alone or supplemental heat

CK heaters can be the sole heat source for small rooms. They can also supplement heat to a room that doesn’t get warm enough from a central source, as sometimes happens with a mini-split retrofit.

Built-in thermostat

All CK heaters have an integral thermostat for easy heat adjustment. CK and CKT heaters can be controlled by a wall thermostat in a room larger than 215 sq. ft.

Booster timer on CKT

The CKT booster timer outputs heat at maximum for up to 60 minutes. When the timer goes off, the CKT reverts to its thermostat setting, maintaining comfort at the original setting.

Frost protection setting

CK heaters have a frost protection setting. The lowest thermostat setting will maintain above freezing temperatures in an appropriately sized space.

CK Trend On/Off Switch

The CK Trend’s convenient and positive on/off switch completely shuts the heater off when it is not needed. The off position will disable the frost protection setting.

Installation notes

These heaters are not supplied with a cord and must be hard-wired.

CK and CKT models stick out 5“ from the wall and the CK Trend models 5⅛”.

Because these are fan heaters that blow warm air out the bottom, the recommended installation location is about 6-8” off floor, with 4” for a minimum.

All CK heaters should be mounted vertically.

Observe all installation manual precautions regarding minimum allowed clearances between the installed appliance and any hard surfaces.

Do not allow combustible materials on or near the heater.