9 best klipsch amplifier for subwoofers

Product description

Klipsch R-100SW 10" subwoofer | Incredibly deep bass and an all-digital amplifier.

• 10" front-firing spun-copper IMG woofer
• All-digital amplifier with 300 watts peak power
• Volume low pass crossover and phase control
• Line level/LFE RCA inputs for maximum receiver compatibility
• Dimensions 14 5" x 12 5" x 16 4"
• Frequency response: 32Hz - 120Hz +/- 3dB
• Amplifier power (Cont/Peak): 150W/300W
• Amplifier features: Volume, low-pass, 0/180 phase, Auto power on

User questions & answers

Question:	Dose it work at 220 volt
Answer:	It will work. It’s 100-240V
Question:	Is it support voltage 100~240V
Answer:	Yes
Question:	is this product working from 220 voltage
Answer:	It will work. It’s 100-240V
Question:	What kind of cable do i need to make this work with klipsch the sixes speakers
Answer:	If this speaker follows the usual Klipsch subwoofer convention, you just need a single cable with RCA/phono/coaxial plugs at both ends. You have to plug it into the jack labeled "L/LFE". If you are sending separate left and right subwoofer signals, then this jack is for the left signal. If you just have one signal, then it treats it as a single LFE signal; that is, like the ".1" part of 5.1 or 7.1 audio. If the jack is simply labeled "L", then you might need an RCA jack to two RCA plugs Y adapter. For a definitive answer, look in the manual, but I suspect that it will handle a common subwoofer signal on the left jack like previous Klipsch subwoofers.

Product features

SPUN-COPPER IMG WOOFER

Injection Molded Graphite (IMG) woofer cones are exceptionally light while being extremely rigid – providing remarkable low frequency response, with minimal cone breakup and distortion to give you the deepest, cleanest bass possible.

All-Digital Amplifier

The built-in, all-digital amplifier of the Reference Series subwoofer delivers ample power with high efficiency and true-to-source accuracy reproduction - thus providing maximum output, detail, and power that fills your home.

CUSTOMIZED BASS

The Reference Series subwoofer gain, low pass crossover, and phase controls ensure the low-frequency tones blend with other speakers and establish the ideal level of bass for your room.

Line level/LFE RCA inputs provide maximum compatibility with standard home theater receivers.

FLEXIBLE PLACEMENT

The high-performance, front-firing driver was designed to provide deep bass regardless of its location in the room to give you more placement options.

Product description

Add robust bass impact to movies and music with the black Klispch R-12SW 12" Subwoofer. This front-firing subwoofer features a 12" copper-spun woofer and delivers up to 400W of power. With a frequency response of 29 - 120 Hz, this model is equipped to handle a wide variety of listening material. Integrated low pass crossover and phase control settings allow you to optimize the sound of the subwoofer in your listening environment. For installation flexibility, LFE and line level inputs are onboard.

• Powerful 12" copper-spun front-firing woofer
• All-digital amplifier delivers 400 watts of dynamic power
• Equally impressive with music and movies; Brushed black polymer veneer cabinet with satin painted plinth
• Low pass crossover and phase control
• Line/LFE inputs for compatibility with most receivers

User questions & answers

Question:	Is this a powered sub? And how many watts does it have
Answer:	Hi Mike, I saw your question and wanted to give you the correct answer. The phase switch determines the way the subwoofer cone ( speaker ) reacts. When set to "0" the speaker cone will move in the outward direction at the same time ( phase ) of your main ( left & Right ) speakers. When it is set to "180" the speaker cone of the sub will move inward when your main speakers' cones are moving outward. What this does is cancel out any overlapping frequencies between your main speakers and your subwoofer. When you have overlapping frequencies between your sub and main speakers you will get too much or "bloated" mid bass. Some people prefer "180" because they feel the cancelled out frequencies produces "tighter" and more accurate bass. Other people like more mid bass, so you need to listen to it both ways to find which you prefer. The same thing will happen if you hook up speakers with the speaker wires hooked up with positive & negative swapped ( positive speaker wire in the negative speaker terminal and negative speaker wire in the positive speaker terminal ). Just as an added note, the "Low Pass" filter knob will determine what lower frequencies pass through from your receiver to your subwoofer. The higher the frequency (Hz) the more mid bass the sub outputs and the lower the frequency (Hz) the less mid bass that the subwoofer outputs. You want the subwoofer to optimally blend with your main speakers and that is what the "low pass" filter knob allows you to do. If you are using a surround sound receiver and it is set for Dolby Digital or DTS surround modes receivers will normally automatically crossover the sub output at 80 Hz, so moving the Low pass knob on the sub beyond 80 Hz will have no effect. Now, if you have a surround receiver that utilizes the Audyssey Microphone system to adjust the surround parameters you will want to set the subwoofers low pass knob all the way to the highest frequency. The Adyssey system will determine what frequency blends best with your main speakers. Hope this is helpful.
Question:	What gain setting do you have your subwoofer set to? I want as much bass as possible from my audio sources (tv, games, movies, etc
Answer:	Yes, there is base and treble adjustment, as well as Vizio truVolume adjustment. We have two of these, I have been impressed with the richness of the sound on this particular model.
Question:	Are the surrounds foam or rubber...getting tire of foam
Answer:	yes , it will right out of the box.
Question:	What does the phase toggle do? I read ther manual, but it didn't explain it in a manner I could understand
Answer:	This sound bar uses Bluetooth version 4.1.

Product features

HAPPINESS IS COPPER AND BLACK

The Klipsch Reference subwoofers feature powerful copper-spun front-firing woofer and an all-digital amplifier to deliver dynamic power like you've never felt before.

Product description

A step-up from our Reference Series subwoofers, The SPL Series have best-in-class MAX output levels making them high-performance subwoofers at affordable prices. Cerametallic woofers are exceptionally light and extremely rigid, providing remarkable low frequency response with minimal cone breakup and distortion for higher, cleaner output using less amplifier power. The built-in, high efficiency amplifier features an analog preamp design, which maintains the original signal path for cleaner, true-to-source reproduction. The class D output stage ensures MAX efficiency for MAX output, detail, and low frequency power. Proprietary internal geometry that minimizes port Noise for clean undistorted low frequencies. The front-firing design allows for placement flexibility. The Klipsch wa-2 wireless subwoofer kit (sold separately) allows high resolution wireless connectivity for easy placement anywhere in your room and optimizes output and low frequency response. Connect up to 4 wa-2 wireless Kits to compatible Klipsch subwoofers in a single room for a completely wireless connection. Low pass Crossover and variable phase control allows you to tune the subwoofer to your Klipsch speakers and to your room, establishing the ideal level of bass. Line level/ LFE RCA inputs ensure compatibility with home theater receivers. Both the RCA and wireless inputs can be utilized, giving you the ability to use A single subwoofer with multiple system in the same room. For example, you can use the wireless input for your home theater set up and the RCA input for your 2-channel system, without needing to switch inputs when changing between systems. Exceptional efficiency on or off. Meets global efficiency standards - reducing energy costs for the user. Scratch resistant Ebony finish looks like real wood and covers the entire cabinet.

• 12 inches long throw cerametallic woofer
• Maximum acoustic output 118dB
• 600 Watts
• Wireless with optional Klipsch WA-2 accessory. Enclosure Material: MDF

User questions & answers

Question:	Is an LFE cable included
Answer:	A standard power cable is included but no other cables. I ordered a MediaBridge shielded coax cable with RCA plug connectors when I ordered the sub. https://www.amazon.com/dp/B00FMZX5RI/ref=tsm_1_tp_tc
Question:	Can you pair this with the klipsch 12sw
Answer:	The SPL-120 is a premium a subwoofer that has more power. They would not match, but you could run them in the same system.
Question:	Is this an authorized and authentic klipsch product? i wasn’t aware these spl subs were available yet
Answer:	Yes they are authorized and authentic if it says shipped and sold by amazon.com
Question:	what does "spun copper" mean? What does "cerametallic" mean
Answer:	It's what the subwoofer is made out of. That's why it's a copper color.

Product features

Klipsch SPL Subs

The built-in, high-efficiency amplifier features an analog preamp design, which maintains the original signal path for cleaner, true-to-source reproduction. The Class D output stage ensures maximum efficiency for maximum output, detail, and low-frequency power.

WOOFER ANATOMY

Klipsch Cerametallic cones are matted to a dual-layer, copper-wound voice coil for exceptional conductivity. Reference Premiere woofers are housed in a non-resonating, stamped-steel basket that’s secured to a large magnet motor for exceptional efficiency and low distortion, and matched to our horn-loaded tweeters for optimal acoustic execution.

YOU CONTROL IT ALL

Low Pass Crossover and Variable Phase control allows you to tune the subwoofer to your Klipsch speakers and to your room, establishing the ideal level of bass. Line Level / LFE RCA inputs ensure compatibility with home theater receivers.

Both the RCA and wireless inputs can be utilized, giving you the ability to use a single subwoofer with multiple systems in the same room. For example, you can use the wireless input for your home theater set up and the RCA input for your 2-channel system, without needing to switch inputs when changing between systems.

Product description

A step-up from our Reference Series subwoofers, The SPL Series have best-in-class MAX output levels making them high-performance subwoofers at affordable prices.

• Bass reflex via exclusive front firing internal flare port for placement flexibility
• High efficiency class d amplifier with 400W RMS and 800W peak
• Compatible with Klipsch wa 2 wireless kit
• Premium scratch resistant finish in Ebony
• Shock absorbing rubber feet, steel grille posts and a woven cloth grille for a premium look and feel

User questions & answers

Question:	Does it have international warranty
Answer:	Our subwoofers carry a warranty shown at klipsch.com/warranty-subwoofers. The warranty service if needed would be provided in the country where the item is purchased.
Question:	how does it compare to the R-115sw? What are the differences
Answer:	These two models are the same in spec and technology. R-115SW being the older model and SPL-150 being the newer model in the same position in our subwoofer line up. The main differences are the finish and that the SPL-150 has feet instead of the plinth used on the older model R-115SW.
Question:	china? or Hope Arkansas
Answer:	Klipsch designs and engineers all of our products in the United States. For more than 70 years, we have continued to proudly build many of our speakers lines at our factory in Hope, Arkansas This particular product was assembled in China. We assure you – it rocks!
Question:	I have a klipsch r-110sw subwoofer - can i add this sub next to it, or should i simply replace it with this sub
Answer:	If your amp has 2 subwoofer outputs......you certainly could have one on the left and one on the right......but the spl15 is a powerhouse......I have a dennon receiver And my basement is 2700 sq ft with a solid 1500sq ft of open space and the spl15 literally rocks the whole basement and shakes everything in my 2800 sq ft upstairs...... including the window blinds. This is at about half volume!!! I would go with one spl15 or 2 spl10 subs.

Product features

Klipsch SPL Subs

The built-in, high-efficiency amplifier features an analog preamp design, which maintains the original signal path for cleaner, true-to-source reproduction. The Class D output stage ensures maximum efficiency for maximum output, detail, and low-frequency power.

WOOFER ANATOMY

Klipsch Cerametallic cones are matted to a dual-layer, copper-wound voice coil for exceptional conductivity. Reference Premiere woofers are housed in a non-resonating, stamped-steel basket that’s secured to a large magnet motor for exceptional efficiency and low distortion, and matched to our horn-loaded tweeters for optimal acoustic execution.

YOU CONTROL IT ALL

Low Pass Crossover and Variable Phase control allows you to tune the subwoofer to your Klipsch speakers and to your room, establishing the ideal level of bass. Line Level / LFE RCA inputs ensure compatibility with home theater receivers.

Both the RCA and wireless inputs can be utilized, giving you the ability to use a single subwoofer with multiple systems in the same room. For example, you can use the wireless input for your home theater set up and the RCA input for your 2-channel system, without needing to switch inputs when changing between systems.

• 400-watt RMS amplifier (800 watts peak power)
• compatible with the wireless audio adapter kit for an easy connection to a sound system
• 15" spun-copper Cerametallic woofer
• Dimensions: 21.5" H x 19.5" W x 22.3" D
• All-digital amplifier delivers 800 watts of dynamic power

User questions & answers

Question:	I have 2 subs for 5 yrs now! All the connections are fine, but there not thumping! What’s wrong
Answer:	Depends on what you mean by “not thumping.” If they’re not making any sound at all, it could be the receiver output if they used to work and suddenly both stopped. If they’re just quieter than normal and you’re missing that punch that comes with things like explosions or bass drums, you have a few options: 1. Your receiver, streaming device, and/or tv may have an option called “Night Mode” or “reduce loud sounds” essentially muffling volume spikes to avoid disturbing others nearby, 2. For some reason your receiver may have turned down the output volume of the subs to a much lower level than you had before, or even glitched and removed the subs from your setup so it’s not even sending out a signal at all, 3. The bass/treble of the receiver could have been adjusted to dampen the bass, or 4. The physical knobs on the back of your subs could have been adjusted turning down the volume, or the passthrough was set so low there’s a gap between what your mains put out and where your subs pick up the low end (ie. your main L&R channels only go down to 100hz and your subs are set to not put out anything above 50hz). These options get progressively less likely and would require either settings being changed or physical aspects of the subs to be adjusted; however, these are also the easiest fixes. You might be looking at needing new subwoofer cables, after five years the amps on the subs may have gone out (east to find replacements on eBay or contact Klipsch directly), or—as I said in the beginning—your “sub out” port(s) on the receiver may have given out. Good luck!
Question:	what is the difference between the R-115sw and the SPL
Answer:	Age. The R-115sw was phased out as they began releasing the SPL-150. They are essentially the same apart from price and age at this point. Slightly different cabinet build, but I don’t even think they really upgraded the amp that powers it.
Question:	Is power only 110 volts or is there a switch to power 220 volts
Answer:	Only works in 110/120V power grids. This RSA-500 does not have switching Voltage.
Question:	I can connect to just one rw-5802 right? I realize that's two subs but one enclosure
Answer:	Each RW-5802 drives 2 subs. You can connect as many RW-5802's as your your amp or pre amp will handle. For example if you choose to use the built in crossover of your amp you will have 1 or 2 sub outputs. You can also route from your speaker outputs to the RW-5802 to us the 5802 cross over to subs then the rest of the signal can continue on to your speakers. Depends on how creative you want to get.
Question:	Can you connect 2 or more SubWoofers
Answer:	It will handle 2

• The country of origin is China
• 12-inch spun copper Cerametallic woofer. All-digital amplifier delivers 600 watts of dynamic power
• Front-firing slot port with exclusive internal flare technology
• L/R line-level/LFE RCA inputs for compatibility with most receivers. Brushed black polymer veneer cabinet with satin painted plinth
• For a simple wireless connection, add an optional Klipsch WA-2 Wireless Subwoofer Kit

User questions & answers

Question:	I'm considering 4 of these rp112sw. Can i plug one into the other? I only have 2 ports in my sr
Answer:	Since subs aren't right and left, you can just buy a splitter and send 2 signals out of each port. Mediabridge should have those cables.
Question:	Hi ya'll, what is your subwoofer db set on your reciever? what setting is your low pass knob on, behind the subwoofer? lfe? thank you
Answer:	Thanks for your question. The settings vary room-to-room, set-up to set-up. There is no single perfect setting. World Wide Stereo is 37 years old and a very proud Klipsch dealer.
Question:	when hooked up to a good reciever can this Klipsch 12 pound
Answer:	I own this R-112SW installed in a 6..1 Klipsch Reference Premiere arrangement. This sub is a BEAST. I also have my best system installed in my master bedroom. It is a 7.2.4 all Klipsch Reference Premiere setup using two of the larger more powerful R-115SW subs and while I love that system to death I would say that especially for music the R-112SW has tighter bass and sounds spectacular. The R-115SW's are killer as well and a bit better (but not much) for movies. I cannot imagine anyone not being completely blown away by the performance of either of these subs. Know also that these subs all have built in powerful amps and will not tax your AVR/Receiver in any way.
Question:	I have a large theater in my house would 2 R-112SW subwoofers work better than
Answer:	When it comes to drivers, especially subs which require a fair amount of displacement for sub frequencies (less for a ported setup like this), more is always better. Larger (more cone area) with all else being equal is always better for sound quality and output. The more power you put into the sub, the more distortion. The farther the sub has to move (excursion), the more distortion it produces. Having a second identical sub means LESS THAN HALF the power and excursion for the same output due to coupling which increases efficiency (the amount of power you will require) and decreases distortion. I competed in car audio sound quality competition and I used 2x 16” subs that rarely got cranked up any louder than a single 10” was capable of but they were so efficient and distortion was so low. At 1mm of excursion, a single 10” would be moving a couple inches for the same output with a ton of power required. My home system was 4x 15” (Acoustic Elegance) and both the home and car were infinite baffle. I can go on for days but would two of these work better than one, absolutely yes, for efficiency and for sound quality. Do you need a pair vs a single, would you be able to hear a difference, it depends on a lot of things but probably not unless you’re really serious about your sound quality and if you’re going to push the single driver really hard. Don’t forget that with a sealed setup, it requires 4x more displacement to go an octave lower at the same volume. Getting that displacement from more cone area vs excursion will reduce distortion and increase efficiency. With a ported speaker like these it’s a little more complicated but you get the point. Don’t forget, a single 15” sub has about 1.7x more cone area than a 12” and a single 12” is going to have about 1.3-1.5x more cone area than a 10”. And before anyone says it, no, a 15 is not “slower”, “boomer”, or “sloppier” than a 12, 10, or 8” sub. No myths please. A single 15 in this case might have been a good idea when cost is factored in but this is 2 years old (yes, I’m bored) and I’m sure the OP is happy with his purchase.

Product description

An updated grille, along with the Black and copper accents you’ve come to identify as the Klipsch trademark colors, create a sleek, sophisticated look for this dynamic sub. Place it anywhere in your home and prepare for bone-rattling bass.

• Spun copper front-firing cerametallic woofers
• 10-inch, down-firing driver
• 200 watts continuous, 420 watts dynamic power
• Black and copper accents for a sleek, sophisticated look
• Connector type-component

User questions & answers

Question:	Is this compatible with Klipsch's Reference (R) series
Answer:	Thanks for your question. The settings vary room-to-room, set-up to set-up. There is no single perfect setting. World Wide Stereo is 37 years old and a very proud Klipsch dealer.
Question:	What is he Ohmic value of this speaker
Answer:	I own this R-112SW installed in a 6..1 Klipsch Reference Premiere arrangement. This sub is a BEAST. I also have my best system installed in my master bedroom. It is a 7.2.4 all Klipsch Reference Premiere setup using two of the larger more powerful R-115SW subs and while I love that system to death I would say that especially for music the R-112SW has tighter bass and sounds spectacular. The R-115SW's are killer as well and a bit better (but not much) for movies. I cannot imagine anyone not being completely blown away by the performance of either of these subs. Know also that these subs all have built in powerful amps and will not tax your AVR/Receiver in any way.
Question:	Can i use a 2 male to 1 male to connect it to my receiver? i have a yamaha rx-v381 (1 subwoofer output
Answer:	When it comes to drivers, especially subs which require a fair amount of displacement for sub frequencies (less for a ported setup like this), more is always better. Larger (more cone area) with all else being equal is always better for sound quality and output. The more power you put into the sub, the more distortion. The farther the sub has to move (excursion), the more distortion it produces. Having a second identical sub means LESS THAN HALF the power and excursion for the same output due to coupling which increases efficiency (the amount of power you will require) and decreases distortion. I competed in car audio sound quality competition and I used 2x 16” subs that rarely got cranked up any louder than a single 10” was capable of but they were so efficient and distortion was so low. At 1mm of excursion, a single 10” would be moving a couple inches for the same output with a ton of power required. My home system was 4x 15” (Acoustic Elegance) and both the home and car were infinite baffle. I can go on for days but would two of these work better than one, absolutely yes, for efficiency and for sound quality. Do you need a pair vs a single, would you be able to hear a difference, it depends on a lot of things but probably not unless you’re really serious about your sound quality and if you’re going to push the single driver really hard. Don’t forget that with a sealed setup, it requires 4x more displacement to go an octave lower at the same volume. Getting that displacement from more cone area vs excursion will reduce distortion and increase efficiency. With a ported speaker like these it’s a little more complicated but you get the point. Don’t forget, a single 15” sub has about 1.7x more cone area than a 12” and a single 12” is going to have about 1.3-1.5x more cone area than a 10”. And before anyone says it, no, a 15 is not “slower”, “boomer”, or “sloppier” than a 12, 10, or 8” sub. No myths please. A single 15 in this case might have been a good idea when cost is factored in but this is 2 years old (yes, I’m bored) and I’m sure the OP is happy with his purchase.
Question:	What are the full specs
Answer:	Our newly redesign BBL pillow is different than the original BBL pillow. This BBL pillow ergonomic design with curve structure is the perfect solution to provide extra support for a more comfortable sitting experience after your BBL surgery and it’s NOT meant to sit directly on the pillow. Its unique contoured curve structure shape supports your thighs and keeps you elevated so your buttocks hangs freely. This is also our preferred driving pillow. Our Pillow has an easy removal cover and is machine washable.

Product features

PERFECT HARMONY

The Klipsch Synergy Black Label Series is an amazing value in high-performance entertainment.

EASY INTEGRATION

Not only does the Synergy Series offer high-efficiency, world-class sound, the components’ sleek black ash vinyl finish complements any home decor.

LEGENDARY TECH FOR AN EPIC SOUND

Synergy Black Label floorstanding speakers, bookshelf speakers, and center channel speakers feature Klipsch proprietary Tractrix horn technology, which provides a uniform, 90 x 90 dispersion pattern and allows for placement just about anywhere.

HEAR EVERY NOTE

Synergy Black Label speakers are designed to give you an amazing sound stage with the latest technology inside these sleek speaker components:

• ALUMINUM DIAPHRAGM COMPRESSION DRIVER (TWEETER): Produces crystal-clear high frequencies
• LINEAR TRAVEL SUSPENSION: Minimizes distortion
• IMG WOOFERS: Create tight musical bass

Product description

The Synergy Black Label Sub-120 subwoofer uses Klipsch Tractrix Horn technology to optimize output and low-frequency extension. An updated grille, along with the black and copper accents you’ve come to identify as the Klipsch trademark colors, create a sleek, sophisticated look for this dynamic sub.

• Spun copper front-firing Cerametallic woofers
• 12-inch, down-firing driver
• 200 watts continuous, 420 watts dynamic power
• Included components: manual

User questions & answers

Question:	What’s the difference between the 120sw and the 12sw
Answer:	Hi. To check if this car radio fits your car, please measure and compare the screen size, installation size and confirm the harness with your car. This car radio main screen size: 250(W)*145(H)mm. With metal sheet fixed on, installation size: 180(W)*75(H)*70(D)mm. It comes with a harness with naked wires, without connector. Due to the different design of the car console, some may fit perfectly, but some needs to purchase an extra dash kit or cut a piece from the dash to make it fit perfectly. Below website would help you find suitable dash kit, please come into it and type your Car Model + Car year www.metraonline.com If you have any questions or need any help, please kindly contact our support team [email protected]
Question:	The right size is 16.5, 18.5 and 14 inch
Answer:	Hi. To check if this car radio fits your car, please measure and compare the screen size, installation size and confirm the harness with your car. This car radio main screen size: 250(W)*145(H)mm. With metal sheet fixed on, installation size: 180(W)*75(H)*70(D)mm. It comes with a harness with naked wires, without connector. Due to the different design of the car console, some may fit perfectly, but some needs to purchase an extra dash kit or cut a piece from the dash to make it fit perfectly. Below website would help you find suitable dash kit, please come into it and type your Car Model + Car year www.metraonline.com If you have any questions or need any help, please kindly contact our support team [email protected]
Question:	Matching speakers
Answer:	Hi. To check if this car radio fits your car, please measure and compare the screen size, installation size and confirm the harness with your car. This car radio main screen size: 250(W)*145(H)mm. With metal sheet fixed on, installation size: 180(W)*75(H)*70(D)mm. It comes with a harness with naked wires, without connector. Some cars need to buy a dash kit box/frame and dedicated harness/adapter if you want perfitly fitted. About the original steering wheel control function, if your car need a canbus, this car radio cannot support. Other cars are ok.
Question:	whats the RMS of this one
Answer:	This car stereo is an android unit, by connect with wifi or hotspot, you can surf the internet, you can download app you like, such as TouTube, Facebook, ect. Hope this can help you. If you have any questions or need any help, please kindly contact our support team [email protected]

Product features

PERFECT HARMONY

The Klipsch Synergy Black Label Series is an amazing value in high-performance entertainment.

EASY INTEGRATION

Not only does the Synergy Series offer high-efficiency, world-class sound, the components’ sleek black ash vinyl finish complements any home decor.

LEGENDARY TECH FOR AN EPIC SOUND

Synergy Black Label floorstanding speakers, bookshelf speakers, and center channel speakers feature Klipsch proprietary Tractrix horn technology, which provides a uniform, 90 x 90 dispersion pattern and allows for placement just about anywhere.

HEAR EVERY NOTE

Synergy Black Label speakers are designed to give you an amazing sound stage with the latest technology inside these sleek speaker components:

• ALUMINUM DIAPHRAGM COMPRESSION DRIVER (TWEETER): Produces crystal-clear high frequencies
• LINEAR TRAVEL SUSPENSION: Minimizes distortion
• IMG WOOFERS: Create tight musical bass

• Powerful 12 in. Copper-spun Front-firing Woofer
• All-digital Amplifier Delivers 400 Watts Of Dynamic Power
• Equally Impressive With Music And Movies
• Line/LFE Inputs For Compatibility With Most Receivers

User questions & answers

Question:	Are there any blemishes on the subwoofer
Answer:	Not at all.
Question:	Will this work as a additional sub with the cinema
Answer:	Yes, it will help a lot!!
Question:	What sound bar or center speaker can I pair this sub with
Answer:	Any Polks combination will do the job.
Question:	Is it uncovered or is there a grill to protect the speaker
Answer:	there is a grill to protect the sub.