14 best class d amplifiers

Product description

The Autotek MM2020.1D The Mean Machine 2,000 Watt Subwoofer Monoblock Class D Amplifier brings extreme power with Pro-Fi high speed MOSFETS and high sound quality with minimum distortion levels. The MM2020.1D features 2,000 watts of power in a 1 ohm stable monoblock amplifier designed to power a mono subwoofer system. The Class D technology provides extreme power in a smaller footprint. The amplifier can be run from the output RCA connections which minimize the need for additional cables running the length of the vehicle.

• 2,000 watts mono bridged x 1 @ 4 ohms
• 500 watts x 1 @ 4 ohms
• 1,000 watts x 1 @ 2 ohms
• 0 to 12 dB bass boost
• Road Worthy TCID (Twin Coil Isolation Design) and Pro-Fi High Speed MOSFETS bring extreme power with high sound quality and minimum distortion levels

User questions & answers

Question:	What is a good 10" sub to match with this? Im looking for 1 single but will probably add another 10" later
Answer:	A 2000w sub
Question:	I have DBL coil 12 pioneer 1500 watt will this amplifier push them
Answer:	Yes
Question:	Does this come with a bass knob
Answer:	Yes, mine came with an Autotek bass knob
Question:	what would be the best wire kit to run
Answer:	I just bought a wiring kit and I bought a 4 gauge wire kit. That way it handles the amplifier just fine

Product description

Universal APCLE Series Class D Mono 1500W Amplifier by Audiopipe®. Boasting the latest in technology, this first-rate amplifier from Audiopipe is the finest piece of competition car audio gear that will take your listening experience to a whole new level. Full MOSFET circuit design allows to provide massive power without distortion at any volume. With this high-end amplifier, you sure to enjoy rich, heart-thumping bass with crystal clear sound quality

• 1500 Watts
• 1 Channel Class D
• 1 Channel @ 4 Ω - 600W
• 1 Channel @ 2 Ω - 950W
• 1 Channel @ 1 Ω - 1500W
• Signal to Noise Ratio: >70dB, Frequency Response: 8Hz ~ 180KHz

User questions & answers

Question:	Could I run this at 2ohm for a single Skar ddx12 and get away with a factory 180 amp alternator and amg battery with 4 awg ofc wiring
Answer:	Yes it would be better at 1ohm I have mine at 1ohm with 8k cap it is power hungry but not bad at 2ohm this amp is a beast buy it you will not regret
Question:	What size gauge wire will fit in the 12v power supply input on the amp
Answer:	It's a 4 gauge terminal but I would highly suggest a 1/0 to 4 gauge reducer and running 1/0 gauge to your power supply
Question:	Will this bw fine with 4 guage from battery to distribution block powering 2 amps without thw wire melting
Answer:	I’d say no. This amp pushes well over 1000 watts, which would not do well without a direct 4 gauge to the battery. These also run hot as it is, without adding extra resistance.
Question:	I'm confused it's saying it's a monoblock but yet in the second pic there's 2 channels
Answer:	It can be wired both ways i wired mine to 1 ohm its a 1 ohm stable amp and it is one channel pretty strong too ive had mine for months and no problems with it i run 1 1250rms skar evl 12 with it

• Excellent for voice as well as bass
• 1 ohm
• 3000 watts
• Mono
• Bass boost

User questions & answers

Question:	Esta tarampa puede mover dos audio pipe 12 pulgadas 3600 watts
Answer:	It's made from standard tool steal same as the rest of my ratchets. I have not had a problem with it.
Question:	Do i need a extra battery if i am running a single
Answer:	The pouch is approximately 4" x 2-1/2" x 5/8". I don't have it in front of me right now, but I know it pretty well and I do have a ruler. I figured you'd like a quick answer if you could get one, but you may wish to confirm these numbers with another source..
Question:	Which taramps is better for bass hd or dsp trying to hit 2 15" audiopipe 3 magnets 2400 watts each
Answer:	5 3/8 ounces; 155 grams
Question:	Este taramps de 3000w rms funcionara bien para mis pioner doble bobina serie champions
Answer:	I haven't counted the teeth but I took mine apart and I can say it's very similar to what snap-on makes very high tooth count and very small amount of movement per click I have owned several of these bed ratchets and this is by far one off the best only second to wera brand but those are like 30 bucks this is deffinately top quality and the hex driver end is a big bonus I have used it with he'd sockets and loosened tight 9/16 bolts on my car without it skipping

Product description

PyleHome Model : PCA1.5Compact Stereo Power Amplifier - Mini Audio Power Amp, Wired RCA Connectors, Speaker Terminals, 30 Watt MAX 2X15W Peak At 4-Ohm Power On Led Indicator Master Volume Control RCA Cable L/R Input Four Push Type Speaker L/R Terminals Compatible With Any Audio/Computerize Devices (MP3) Via 3.5mm To RCA Converter. 110/220 Voltage Selector Dimensions:5.61''(W) X 2.17''(H) X 4.21''(D) This mini stereo power amplifier provides up to 15 W of power on each channel at 4 ohms. Connect your inputs using the RCA jacks. Outputs over standard speaker push jacks. It's compatible with any audio or computer device - you can even hook up an iPod using a 3.5mm to RCA jack converter. Master volume control on the front lets you adjust the gain. Runs on 110 or 220 V. Included Components: quick_start_guide

• 2x15 WATT PEAK POWER: The Pyle Dual Channel Mini Audio Amplifier is perfect for your home theater acoustic sound system. Gives you 2x15 watts peak power which can be used for multi speakers at 4 ohms impedance, enjoy high quality music and movies
• MASTER VOLUME CONTROL: The improved compact bookshelf speaker sound amplifier features crisp and responsive buttons for the power switch. It also features rotary knob control for the master volume adjustment. Runs on 110 or 220 V
• MULTIPLE SOURCES: This personal portable digital amp box lets you connect external audio sources such as tuner, CD player, tape deck, camcorder and VCR to the RCA L/R cable input and enjoy enhanced amplified acoustic audio reproduction
• PUSH TYPE SPEAKER TERMINAL: It lets you easily connect speaker wires directly to the amplifier. The speaker impedance ranges from 4 to 8 Ohms for the general stereo output. The total speaker impedance must be at least 4-Ohm per channel at stereo mode
• COMPACT SIZE: The professional integrated stereo receiver features a mini compact size and measures 5.61” W x 2.17” H x 4.21” D, easy to bring anywhere it is needed. Can be used for indoor home and outdoor sound system applications

User questions & answers

Question:	Can I use this for external tv speakers using rca jacks to amp then hook speakers with speaker wire.. Thank you
Answer:	Yes you can. Some tvs have a headphone jack . You can use a cable with a 3.5m headphone jack and two rca (male) jacks to connect to amp. I have done this.
Question:	will this work for the "Dual LU43PW Indoor/Outdoor Speakers" http://www.amazon.com/Dual-LU43PW-Indoor-Outdoor-Speakers/dp/B000A5S926/ref=sr_1_1?ie=U
Answer:	Yes. I use this amp to power those exact same speakers for my radio station’s production studio. Small but mighty. Our jocks don’t spend a great deal of time there so they don’t get used very hard but it still gets the job done...well.
Question:	Can this handle a 400 watt speaker system? Or do you know one I can get for that
Answer:	It will not sound as good as you would like, if you have gear that handles 400 Watts RMS.This amplifier is rated only 40 Watts RMS. So it will not drive your 400W speakers very well. It will work, but you will be disappointed.While it is good sound practice to always have monitors/drivers (speakers) rated higher than the maximum output of the amplifier, for the safety of not blowing out the drivers with any voltage spikes, it is best to have the components much closer in RMS ratings. Say using 60-100 Watt Speakers with this set up, instead of 40 Watt or under, or 100 Watts or over.The little unit will be woefully under powered.I hope this helps!Oh, and BTW, RMS stands for Root Mean Square, the way the wavelength is measured for amplifier output using Ohm's Law.
Question:	Why is it so cheap in price? What's wrong with it? Is it discontinued or something
Answer:	The product is cheap because it is crap. When you plug the amp in to power and speakers, the speakers hum at 60Hz. This is the result of poor shielding between the power supply and the amp electronics, which is purely a function of cheap, crappy manufacturing. Pyle used to make good products - I have several of their amps from ~10 years ago that sound great. But something happened, and their current product line is garbage. It's cheap, but it's not a good deal unless you don't care about audio quality.

Product features

Pyle PCA1.5 2x15 Watt Stereo Power Amplifier

This mini stereo power amplifier provides up to 15 W of power on each channel at 4 ohms. Connect your inputs using the RCA jacks. Outputs over standard speaker push jacks. It's compatible with any audio or computer device - you can even hook up an iPod using a 3.5mm to RCA jack converter. Master volume control on the front lets you adjust the gain. Runs on 110 or 220 V.

• 2X15W Peak At 4-Ohm
• Power On Led Indicator
• Master Volume Control
• RCA Cable L/R Input
• Four Push Type Speaker L/R Terminals
• Compatible With Any Audio/Computerize Devices
• (MP3) Via 3.5mm To RCA Converter.
• 110/220 Voltage Selector
• Dimensions:5.61''(W) X 2.17''(H) X 4.21''(D)

Product description

Quick tips:

1. Please plug the power cord into the amp THEN the wall, plug the audio cables into amp THEN switch on.

Some customers may see some slight sparks flying when they plug the power supply into the amplifier, because they use it in wrong way, you need to connect the amp to the power supply first, then plug the power supply into the 110v AC outlet, don't worry about the sparks, because this is class d amplifier, the capacitors need to charge when the power in, it's normal and safe.

2. The amp will off when you switch off, but it’s normal that the power LED light stay on even switch off, the power LED light on means the power supply in.

3. What will cause noise?

Poor quality audio cables, Sound source, Speakers, Other interfering signals;Incompletely connections.

4. How to judge whether the noise from the amplifier?

Unplug the RCA cable, connect this amp to speakers, and then plug into the power supply, power on and volume on, hear whether noise exists on speakers, if noise existed, the noise may from speakers or amp, so you need to change speakers for further confirmation. If no noise the noise may from the audio source.

🍎With Bass and Treble Control version: B076P2VS9H .

Parameter:

1. Power supply range: 12v-32v;

2. THD: ≤ 0.04%;

3. Frequency Range: 20Hz - 20kHz (±1 dB);

4. SNR: ≥ 98dB;

5. Input sensitivity: ≤ 280mV;

6. Terminating impedance: 2Ohm - 8 Ohm;

7. Output power: 160W + 160W;

8. Input mode: Analog;

9. Power supply: 24V 4.5A;

10. Supplied Accessories: Amplifier, Power supply, AC power cord, Manual.

• Adopt STMicro TDA7498E chip to get clear audio sound, No pop, no audible noise, dead silent when nothing is playing through it.
• 160W X 2(4 ohms, 20 Hz - 20 kHz, 0.04% THD), for outdoor/ bookshelf/ computer/ desktop /ceiling /floor standing speakers, can use iPod, Phone, MP3 players, TV, Echo Dot, CD players, or Streaming Media players as input.
• 2.0CH audio integrated amplifier, aluminum enclosed, small size, good looks, simple functionality, and excellent sound quality;
• Home small Hi-Fi amp, Exclusively designed for the customers who pursue HiFi sound;

User questions & answers

Question:	I see power input is 12-32v... looking for a small amplifier for external tv speakers in an rv. is this unit compatible with automotive 12 volt
Answer:	Supplied with 19 volts So it would work fine with 12 volts. Great Amp! Even at 19 volts, going into 8 ohm speakers, still huge amount of headroom. Too loud for Apt living. And the price is so cheap.
Question:	Is there a better power supply you'd suggest
Answer:	Better than the 24 volt 4.5 amp that comes with the unit? My amp and power supply are working super well driving my Infinity speakers. Loud and clear.
Question:	To get the best output, 32v would obviously be needed. What would be the amperage required at that voltage
Answer:	I asked the vendor. They recommended 29 V 6 amps for the best results.
Question:	ohms speakers
Answer:	2 to 8 ohm = Plus the beauty of D-Class amps is that the quality is moving forward each year & they are able to accommodate low impedance speakers!

Product description

We’re in a time where small is “in”. Smaller, more economical vehicles are more and more desirable. But that doesn’t mean you have to sacrifice big power for your system. Overdrive amplifiers pack huge amounts of power into a smaller chassis thanks to efficient full-range Class - D topology and SMT technology. Complimented with every possible preamp adjustment, overdrive amplifiers leave nothing to be desired

• 1-ohm Stable Monoblock Operation for MAX Power
• Military Grade PCB w/ PWM MOSFET Power Supply
• Direct Short, Thermal, & Overload Circuit Protection
• 12dB Bass Boost Increases Low Octave Harmonics
• Variable 12dB High & Low Pass Crossovers

User questions & answers

Question:	Whats rms @2ohm,4ohm,1ohm
Answer:	3000@1ohm,1500@2ohm,750@4ohms
Question:	Can this amp be bridged at 4ohm
Answer:	yeah
Question:	What’s that extra terminal looking piece used for
Answer:	Its a reducer
Question:	Can you put 2 2 ohm load speakers
Answer:	Yes you can I'm pretty sure if you were them parallel they would be at 1 ohm

Product description

American Bass VFL Monoblock Amplifier Class D Stealth Stealth Series VFL-STEALTH-4500.1D Conservatively rated at 4500 watts @ 1 Ohm mono, this amplifier is designed to drive a daily sub setup without failure. Control features include gain level, subsonic filter (10~50Hz), a low pass filter (35~250Hz), a bass boost of 0~9dB, and bass control knob. The power and ground will accommodate 4 AWG wire and REM connector will accept wire sizes from 12 to 18 AWG. The terminal is used to remotely turn on and off the amplifier when +12V DC is applied. The high pass filter controls the high pass cutoff point for the speaker outputs. HPF can be selected with x-over switch located next to it. Features Stealth Max 4500W Class D Monoblock Amplifier w/ Bass Knob Frequency Response: 10 Hz - 200 Hz RMS Power @ 1 Ohm: 2250W x 1 Max Power: 4500W Signal To Noise Ratio: Greater Than 85 dB Damping Factor: Greater Than 150 Input Sensitivity: 6 V - 0.2 V Subsonic Filter: 10 Hz - 50 Hz Low Pass Filter: 35 Hz - 250 Hz Bass Boost: 0 dB - 9 dB Heavy Duty 2 oz Printed Circuit Board Surface Mount Technology 8.5V - 16 Volts Working Voltage Multi-Way Protection Circuitry Linkable Connection (Output Master/Input Slave) Remoter Gain Control w/ Clip Indicator Dimensions (L/W/H): 18" x 7.75" x 2.3"

• Stealth Max 4500W Class D Monoblock Amplifier w/ Bass Knob
• Frequency Response: 10 Hz - 200 Hz
• Signal To Noise Ratio: Greater Than 85 dB
• Damping Factor: Greater Than 150
• Input Sensitivity: 6 V - 0.2 V

User questions & answers

Question:	Has this amp been bench tested
Answer:	Yeah at budget gem or budget bust on YouTube
Question:	Will 0 gauge wire work or do i need a adapter
Answer:	I have this amp and you will need a 4 gauge reducer If you have 0 gauge wiring that's what I have And the speaker wire is 4 gauge
Question:	Would it push 4 America bass xd
Answer:	It’s 1600watt rms at 1 ohm

Product description

Planet Audio MB1200.1D Class D Car Amplifier - 1200 Watts, 1 Ohm Stable, Digital, Monoblock, Mosfet Power Supply, Great for Subwoofers

• Power - 1200 Watts Max x 1 @1-Ohm, 600 Watts Max x 1 @2-Ohms, 300 Watts Max x 1 @4-Ohms
• Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
• 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
• Variable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
• Variable Subsonic Filter - To prevent your subwoofer(s) from bottoming out, the variable subsonic filter filters out frequencies below the subwoofer(s) specified low frequency limits and allows the driver to reach a maximum safe excursion
• Variable Low Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction
• Variable Gain Control - The gain control is not for adjusting volume. It simply adjusts the amount of signal that is coming from your receiver and going to your amplifier

User questions & answers

Question:	What size fuses does it take and does it bump how many true rms is it
Answer:	it will make your FM reception useless
Question:	does this have signal sensing turn on
Answer:	Yes. The remote wire
Question:	Does it have rca outputs
Answer:	It has RCA IN/OUT
Question:	Will this work with 2 12 kicker comp c
Answer:	No. This amp at its best will be a max of 300w not 1200 like they say. Also the out wires for the speakers are way to thin. you need a 14 or 12g wire for that Save your time and money and get the Rockville RXM-T2 Micro 2400w 2 Ch . I got it and will never regret it like I did with the planet audio. watch Williston Audio Labs review on you tube $115 Hidden Gem? Rockville RXM-T2 Review and Test RXD-T2 [4K] and you will see why. It is that good. This Planet audio is CRAP

Product features

Class D

Class-D amps run more efficiently and generate more power using a more compact design than traditional Class A/B amps.

MOSFET Power Supply

Metal Oxide Semiconductor Field-Effect Transistors quickly switch from full to non-conduction for high efficiency output.

1 Ohm Stable

1-Ohm stable gives you maximum power for superior wattage and performance without overheating. The greater the power the more current drawn from your vehicle's electrical system.

Variable Low Pass Filter

Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.

Subsonic Filter

Subsonic filter restricts low frequencies below the specified setting for better subwoofer protection and performance.

Variable Bass Boost

Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

High and Low Level Inputs

High-level inputs accept speaker output signals and low-level inputs accept pre-amp output signals to allow for the addition of amps and processors to standard factory or aftermarket source units.

Variable Input Control

The Variable Input Control allows the amplifier input to match the output signal from the head unit to achieve optimum performance when adjusted properly.

Product description

Kick your Bass into high gear with the Boss Audio Armor AR4000D Class D Monoblock Amplifier. This powerful 1-Ohm stable Amplifier features 4000 Watts Max Power with a MOSFET power supply to get your tunes rocking. Customize the sound with Variable Low Pass Crossover, Bass Boost and Subsonic Filter. Maximize the Bass with the Remote Subwoofer Control. For double the performance and power, strap on another AR4000D for a total power of 8,000 Watts @2-Ohms. The Armor Series of Amplifiers packs incredible power and performance into a feature-rich slim design for put-it-anywhere convenience. Give power to your playlists with the Boss Audio AR4000D. For further product details, please scroll down.

• Power - 4000 Watts Max x 1 @1-Ohm, 2000 Watts Max x 1 @2-Ohms
• Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
• 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
• Strapping Capable - You are able to strap two AR4000D amplifiers and double the power that is being sent to your subwoofer(s). You now have the ability to connect more subwoofers to take advantage of the extra power
• Variable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
• Variable Subsonic Filter - To prevent your subwoofer(s) from bottoming out, the variable subsonic filter filters out frequencies below the subwoofer(s) specified low frequency limits and allows the driver to reach a maximum safe excursion
• Variable Low-Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction

User questions & answers

Question:	Can i use this with a single ground zero 1000w gzrw 15d4 subwoofer at 4ohms? or should i wire it to a 2 ohm final impedance
Answer:	Hello, The AR4000D provides ample power for your subwoofer. A dual voice coil subwoofer should be wired to provide an impedance of 2 Ohms. Thank you!
Question:	Can this amp push 2 kicker 12" solo baric l7 they each are 2 ohms
Answer:	Definitely. I have one hooked up to 2 Rockford Fosgate 12" P3's and it pushes them really nice.
Question:	Can this amp push 2 15” power acoustic subs
Answer:	Depends,,,what's the RMS on the speakers? This amp puts out at best 400 n change. And that's at 14 watts . so if ur sub's r say 200 RMS or less then I would say yes it will push them. This is a good little amp. Especially for the price. In my ride Its pushing 1 dual coil 12 in sub very nicely.... And its a china sub lol
Question:	Will this amp power 2 soundqubed HDC3 10in subs
Answer:	hdC's? Wow, I dunno what 87 chevycaprice is talkin bout, I'm going to take a safe guess that, (Since you failed to include the specs for the Soundqubed Comp series) he assumed that "it's just another 10" sub, how many 10" subs require astronomical amounts of RMS wattage just to get a slight amount of movement?" & I spose in most 10" subwoofer configurations he'd be right. I however own a 15" HDS3.1 Soundqubed sub, (S- standing for STREET series, meaning it's simply meant to be a daily driver where as w/yours, the C- stands for Comp or competition series) I've had my HDS for over a yr & have already chose to upgrade amps twice due to lack of sufficient power even at a 1ohm load. For the HDS, regardless of weather it's a 10"/12"/15", they ALL require you to feed them AT LEAST their Rated 1200RMS If you want them to even BEGIN to sound as good as they truly can sound...& For just a daily driver series, they're stiffer than a 15yr old pimple faced virgin boy working as a camera man on a Bonnie Rotten porn shoot! Even after pushin 5 months w/an ORION Cobalt 2500.1D @ full tilt, then stepping up to Orion 3500.1D @ full tilt, & now, just over a year into my sub break in process, being powered by a Power Acoustiks RZR 3500.1 at full tilt..... my subs still nearly too stiff for me to even move the cone/spider by hand.... so, although I don't remember off the top of my head the RMS rating of the HDC series I'm quite certain it's AT LEAST 2000 or more... & Oddly enough I can give you a review of this series of BOSS Amps since my previous system was 2JBL 12"s powerd BY an Armor 1500 wired to 2ohm... I don't have anything bad to say necessarily, considering it's a budget Amplifier series built by a budget audio Company, Dollar per watt, the Armor1500 I had would make even the pickiest audiophile smile, if even just slightly. However, I sold that set up B4 havin a chance to clamp test it for absolute clarification, but I've been building, wiring/setting up systems for just under 20 yrs now & I can say with out question they are a fairy tale away from making even close to their spec ratings! I assume you're browsing the BOSS AUDIO Amps cuz budget issues? If I'm wrong bout this assumption & u didnt get your HDC as a gift but w/ your own scratch....then I truly believe, & honestly hope that you'll save your $ & purchase something that will allow that HDC to do what it's meant to do.... It'll blow minds & eardrums I assure you of that! I'm gonna make one suggestion to you & as long as you haven't already purchased an amp I truly hope you'll trust my advice! Look at the Orion XTR1500.1 or 2500.1 dependin on ur RMS rating! I know it'll run you an extra $150-$200 more than this BOSS Amp but I PROMISE you, it'll bring your HDC to the record breaking level of "COMPETITION" that the "C" in its name stands for & you'll NVR regret I can promise you that.! Hope this will help guide you to glory! Lol good luck enjoy that HDC

Product features

Performance Power

Ramp up your vehicle's Bass with the Boss Audio Armor AR4000D Class D Monoblock Amplifier. With 4000 Watts Max Power and MOSFET power supply, this Amplifier packs an audio punch. Customize the sound with Variable Low Pass Crossover, Bass Boost, Subsonic Filter and Remote Subwoofer Control. Strap this Amplifier to another AR4000D for double the performance. The Armor Series of Amplifiers packs incredible power and performance into a feature-rich slim design for put-it-anywhere convenience.

Class D and MOSFET

Class-D amps run more efficiently and generate more power using a more compact design.

Metal Oxide Semiconductor Field-Effect Transistors quickly switch from full to non-conduction for high efficiency output.

Strapping Capability and 1 Ohm Stable

Strap two amplifiers together to get double the power at an impedance of 2-Ohms.

1-Ohm stable gives you maximum power for superior wattage and performance without overheating. The greater the power the more current drawn from your vehicle's electrical system.

Variable Low Pass Filter and Subsonic Filter

Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.

Subsonic filter restricts low-frequencies below the specified setting for better subwoofer protection and performance.

Subwoofer Level Control and Bass Boost

A wired remote lets you easily control the subwoofer level for customized output and superior sound.

Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Low Level Inputs and Variable Input Control

Low-level inputs accept pre-amp output signals to allow for the addition of amps and processors to units equipped with RCA Pre-amp outputs.

The Variable Input Control allows the amplifier input to match the output signal from the head unit to achieve optimum performance when adjusted properly.

Phase Control

Phase control lets you adjust the speaker phase with the amplifier if your speakers or subwoofer are hooked up 'out of phase'.

Short Protection

Automatic shut-off protects the amplifier if it gets too hot or if speakers fail causing a short.

Switchable Input Sensitivity

Switchable input sensitivity provides adjustable control over the input signal from the head unit to achieve customized balance between power and sound quality.

Product description

You're not one to show off, but if you got it, why not? Believe us, you'll have it when you throw this Hifonics BXX1200.1D in your system. BXX1200.1D Hifonics put a lot of cool features in the BXX1200.1D aside from raw power. The Ultra-Fi MOSFET power supply does more than push power to your subs, it makes sure what it's pushing sounds good. Why settle for just pure wattage? Make sure it sounds like it should! Pair that with the Super D-Class design circuitry, the classically awesome-looking heatsink and a built-in electronic equalizer, and you've got a lot great sound to go with that high wattage. Not enough power? Strap it! If your system demands even more, the BXX12001.D is ready to team up with another amp to supply all the power you need. Just make sure your electrical system is up to the task. General Features: Hifonics Brutus Series BXX1200.1D Class-D 1-Ohm Stable Monoblock Amplifier Max Power Rating: 4 ohms: 400 watts x 1 chan. 2 ohms: 600 watts x 1 chan. 1 ohm: 1200 watts x 1 chan. Total power output: 1200 watts Pulse Width Modulated MOSFET power supply Wired remote bass level control included LED power (green) and protect (red) indicators Soft start turn-on Mono channel operation Preamp RCA outputs to daisy chain multiple amps 3-way protection circuitry (thermal, overload, and speaker short protection) Dual speaker terminals simplify the hookup of multiple speakers Heavy duty aluminum alloy heat-sink Frequency Response: 10 - 250 Hz Total Harmonic Distortion (THD): .1% Signal to Noise Ratio: >95 dB Variable low-pass filter: 30 - 250 Hz, 12 dB/octave Subsonic filter: 15 - 35 Hz Variable Bass Boost: 0 to +10 dB bass boost Fuse Rating: 80A x 1, Maxi

• The BXX1200.1D is a 1200 watt mono amplifier featuring Super Class D technology with an NGSD digital chip to provide you with an extremely efficient, low temperature, high amplification system that others only dream about.
• The rock solid Ultra-Fi MOSFET outputs are selected for both balance and output power. This keeps power smooth even during demanding peak in the music.
• The amplifiers protection condition is also shown by blue illumination for normal operation and red for a short being present and requires the attention of an installer.
• Max Power Rating: 4 ohms: 400 watts x 1 chan. 2 ohms: 600 watts x 1 chan. 1 ohm: 1200 watts x 1 chan.
• Dimensions: 9"W x 13.25"L x 2.5"H, 1-year Manufacturer's Warranty

User questions & answers

Question:	Este amplificador me mueve 2 12” skar sdr -12 D4 600 watts rms cada uno
Answer:	sí, conectelos en serie a 1 0hm y debería ser bueno.
Question:	I had a brz1200.1 but it died after years of heavy use. Is this the newest version of that model? Looking for an exact or close to match
Answer:	Yup...same here I had two of the older models and one finally gave out after years of use. It actually just fried when it was 103 degrees out last summer and the truck wasn’t in the garage all weekend. Cab gets hot. Got this to replace it.
Question:	Is this amp 1 ohm stable
Answer:	Yes it is 1 ohm stable.
Question:	Will this amp handle 2x JL audio 12” w3v3 4 ohm wired together
Answer:	Yes, they'll be wired down to 1ohm

Product description

Sound Storm Laboratories CG3000.1D Class D Car Amplifier - 3000 Watts, 1 Ohm Stable, Digital, Monoblock, Mosfet Power Supply, Great for Car Subwoofers

• Power - 3000 Watts Max x 1 @1-Ohm, 1500 Watts Max x 1 @2-Ohms, 750 Watts Max x 1 @4-Ohms, 6000 Watts Max x 1 @2-Ohms Strapped / Bridged
• Class D - Power loss is significantly reduced making the amplifier highly efficient. Excess energy is stored until it’s needed instead of being converted into heat. Reduction in size/weight, reduced power waste, smaller heat sink, compact circuitry
• 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to
• Strapping Capable - You are able to strap two CG3000.1D amplifiers and double the power that is being sent to your subwoofer(s). You now have the ability to connect more subwoofers to take advantage of the extra power
• Variable Bass Boost - Bass Boost allows you to adjust the low bass within the boost range to just the way you like it
• Variable Subsonic Filter - To prevent your subwoofer(s) from bottoming out, the variable subsonic filter filters out frequencies below the subwoofer(s) specified low frequency limits and allows the driver to reach a maximum safe excursion
• Variable Low Pass Crossover - Subwoofers reproduce sound based on a number of different low-range frequencies. You can set exact sound specifications for the bass frequency reproduction

Product features

Class D

Class-D amps run more efficiently and generate more power using a more compact design than traditional Class A/B amps.

MOSFET Power Supply

Metal Oxide Semiconductor Field-Effect Transistors quickly switch from full to non-conduction for high efficiency output.

Strapping Capability

Strap two amplifiers together to get double the power at an impedance of 2-Ohms.

1 Ohm Stable

1-Ohm stable gives you maximum power for superior wattage and performance without overheating. The greater the power the more current drawn from your vehicle's electrical system.

Variable Low Pass Filter

Variable low-pass filter gives you control over the frequencies that pass through to the subwoofer.

Subsonic Filter

Subsonic filter restricts low-frequencies below the specified setting for better subwoofer protection and performance.

Variable Bass Boost

Variable Bass Boost allows you to adjust the low bass within the boost range to just the way you like it.

Low Level Inputs

Low-level inputs accept pre-amp output signals to allow for the addition of amps and processors to units equipped with RCA Pre-amp outputs.

Product description

Get the most out of your sound with the Kicker 46CXA8001T 1600-Watt Max Power Class D Amp Mono Car Audio Sub Amplifier. CX-Series mono amps are ohm stable, giving you even more power and wiring options for your system. A powerful 12 dB crossover and 24 dB subsonic filter are included, letting you quickly tune your system to perfection. Use the full-range outputs to expand your system with other bass amps, or a full-range amp to complete your system. This car amplifier also features KickEQ 6dB variable bass boost for those additional low frequencies, as well as FIT+ (Fail-safe Integration Technology-PLUS) so it works with nearly every radio. The Kicker Kicker 46CXA8001T amp accepts up to 40 volts of speaker-level input signal. This kind of flexibility makes line-out converters unnecessary and optimizes your sound quality.

• CLASS D DESIGN WITH 800 WATTS OF POWER: Efficient Class-D amplifier with 1600 watts of peak power and 800 watts of RMS power
• ELIMINATES UNWANTED INTERFERENCE: 3-second turn-on/off delay to eliminate unwanted interference
• VARIABLE CROSSOVERS: Variable 12dB crossovers provide control to dial in the perfect sound
• KICKEQ BASS BOOST BUILT-IN: KickEQ 6dB variable bass boost for those additional low frequencies
• PROTECTION FROM DAMAGING FREQUENCIES: 24dB subsonic filter for protection from potentially damaging frequencies

User questions & answers

Question:	It works whit the l7s15 solobaric 15" subwoofer square l7 4 ohm
Answer:	Yes
Question:	Is this a 2 chanel amp? I have a single dual coil sub 4ohm do i connect it on each output terminal or brigde
Answer:	It’s a single..”mono”
Question:	How many channels
Answer:	I can look i already hooked one box you can see in the picture but still I can hook up one more box quality it’s really good clear bass if you put face up speaker then no body vibration.
Question:	Can I bridge this amp
Answer:	It's a mono amp, which means there's only one channel, so you can't bridge it. There's nothing to bridge. You simply connect your subwoofers to the speaker outputs, whether your setup requires parallel, series, or otherwise. Just be sure to not exceed the impedance that the amp is rated to handle on the low end. (Don't go too low with the impedance load at the terminals for all your combined subwoofers)

Product description

Father of the gods - Zeus delivers a full range of amplifiers to the mortal car audio enthusiasts of Earth. The Zeus line of amplifiers from Hedonics is a throw back to the original Hedonics amplifiers that helped start the car audio and SPL craze. These amplifiers are packed with technology for great sound and huge power. Complete lineup of super class A/B Multi-Channel amplifiers and class D mono amplifiers illuminated Hedonics badge old school Hedonics Heatsink for Superior heat dissipation military grade PCBSPC - Simpatico coil design - Hedonics Surface Mount design MOSFET power supply for Maximum current levels diagnostic indicators DC, short circuit, Thermal and overload Protection Low level RCA inputs and outputs classic Hifonics aluminum heatsink with a Zeus 3200 Watt, 1 ohm stable, Class D mono subwoofer car audio amplifier. Features include onboard electronic crossover and boost EQ. Bass remote included

• CLASS D AMPLIFIER - Class D topology ensures high efficiency with big power and a small footprint. This mono amplifier was built for driving subwoofers and subwoofer systems, maintaining the highest sound quality sound for your car audio.
• BUILT FOR POWERFUL SOUND - Minimize heat generation with the PWM MOSFET power supply providing stability through the PC board. Old school Hifonics aluminum heat sink maintains superior heat dissipation to keep your car audio sounding smooth.
• MADE TO LAST - Low noise preamplifier generates maximum low voltage signal from source unit, minimizing distortion. High temperature impact resistant inputs with hex screw terminals allow secure connections and are erosion resistant.
• HIGH QUALITY CONNECTIONS - RCA outputs and a daisy chain multiple amplifier build eliminates additional signal cables from the source unit. Molded secure connections are used for all wires and angled for ease of access during installation.
• CLASSIC HIFONICS LOOK - The ZXX Series maintains the classic feel of Hifonics amplifiers and include an illuminated logo on the front of the amplifier. The Hifonics logo illuminates when the amp is powered, making a statement even in the dark.

User questions & answers

Question:	I’m trying to push 3 12’s any help
Answer:	All depends on the specs of the 12’s. What ohms, and power ratings.
Question:	What’s the best amp to use to power 2 15s solo square subs
Answer:	A good one
Question:	Will this amp push 2 sundown 15 inchc CBX
Answer:	Not sure what the rms is on the subs you have but I'm running this amp at 2ohm pushing 2 skar vxf 15s. Running dual inputs on power and ground and it does a good job I beat on it daily with no issues
Question:	How much power does the hifonics 3200 watts require
Answer:	It requires 0 gauge wiring and reccomends a 250 amp inline fuse/circuit breaker. So it requires max of 250amps?

Product features

FATHER TO ALL THE GODS

ZEUS has been delivering incredibly powerful and very affordable car audio amplifiers to the mortal car audio enthusiasts of Earth for decades. The new ZEUS line of amplifiers from Hifonics still maintains that throwback look of the original Hifonics amplifiers but they are packed with technology for great sound and huge power. People used to have to spend a thousand dollars for an amplifier like this, now it is the most affordable way to get started in real high end car audio design.

• Small simple compact design but practical and powerful, little Hi-Fi Bluetooth wireless amplifier exclusively designed for the customers who pursue HiFi sound;
• Bluetooth 5.0 core, up to 50ft connection range guarantees low signal delay. No pop, no audible noise when Bluetooth connection is established;
• 100W RMS X 2(4 ohms, 20 Hz - 20 kHz, 0.04% THD), comes with 24V power supply, can drive 280watts(8 ohm), 320watts(4 ohm) speakers, (For passive speakers only, not the powered speakers.)
• Advanced circuitry design, built-in speakers protection circuit, best for bookshelf/computer/desktop/speakers in your home;
• Home integrated digital amplifier, 18-month warranty, you can return the item if you have any problems;

Product features

2.0 Channel Bluetooth Stereo Amplifier

• Power Adapter: 24V/4.5A
• DC Input Range: 12-24V
• Terminating Impedance: 2 Ohm - 8 Ohm
• MAX Power Output: 100W x 2
• THD ≤ 0.04%
• Frequency Range: 20Hz - 20kHz (±1 dB)
• SNR ≥ 98dB
• Input Sensitivity ≤ 280mV
• Input Mode: Bluetooth and RCA
• Bluetooth Transmission Distance: Up to 50 Ft

Extraordinary Clarity Hi-Fi Sound

Instant setup with phones, tablets, and almost any other Bluetooth-enabled device. Bluetooth 5.0 chip ensures your devices maintain a strong, stable connection up to 50 Ft away for skip-free music.

Advanced Audio Architecture

The High-Performance Texas Instruments TPA3116D2 Chip presents music with rousing highs and deep lows. Even at high volumes, there’s less than 0.04% harmonic distortion resulting in remarkable clarity.

Irresistible Finish

Fosi Audio BT20A curved edges and sleek controls accentuate its unibody design. With truly useful features, and thoughtfully designed premium enclosures. A new generation: exquisite design, improved operation.

Drive passive speakers

Perfect if you prefer separate passive speakers and preamps for your audio setup. 100 watt per channel power output can drive most home passive speakers to create astonishing Sound. Easy to fit your audio system with Bluetooth and RCA input

Upgraded DC Outlet

The old version or other brand amplifiers sparks flying when power supply plugin, it's unsafe. With a built-in power protection circuit, there are no sparks flying when you plug the power adapter into the amplifier. Safe for use!

24V/4.5A Power Supply

Fosi Audio BT20A equip with the energy-efficient and stable power supply can get an astonishing sound.