12 best usb hub for car hardwire

Product description

compatible to Apple iPhone, HTC smartphone and other 5V phone devices.

• kit includes one ultra compact USB port direct hardwire kit for car or motorcycle only
• simple solution of adding an onboard USB charging port for your Apple iPhone, smartphone, GPS, XM Sirius Satellite Radio and many other mobile devices. for Apple Lightning 8 pin, 30 pin, Micro, Mini USB cable.
• easy installation: use a fuse tap or wire tap to draw power from fuse block or wire.
• cable length: approx 5-1/2' in total, 1' from type A female USB to regulator box, 4-1/2' from regulator box to wire end. additional wires can be added to the kit's end to increase the total length. regulator power spec.: 12V~24V input, 5V 1200mA output, regulator box size: about 2-1/2"x 1' (4.5cm x 2cm)
• 30 days money back, one year replacement warranty

User questions & answers

Question:	Will this work with a Droid Maxx
Answer:	So far I've had mine on over the winter and I just pulled it off the other day and the car looked fine.
Question:	How much current can this supply at 5 Volts
Answer:	So far no water has gone through as car is dry. Although it is thin, so wind or sun an cause it to rip a bit over time.
Question:	Does regulator draw power when not in use
Answer:	The cover says it's all weather so I would hope it would. The cover material is like other car Covers. It has elastic around the bottom so it fits right to the vehicle. It also has two holes on each side and comes with string so you can also tie the cover underneath the car but honestly so far we haven't used the ties yet and it's been pretty rainy and windy here and we've had no problems with the cover coming off or even moving. The elastic helps it so much. It's held up against the rain and wind very nicely. We plan on getting another one of these covers for father in law. Hope this helped!
Question:	Hi guys, what amp fuse did you use with this for the add a circuit? Is a 5A fuse ok
Answer:	mine do not connect . have never had any problem with the threads

Product description

Add up to 4 devices with the efficient, effectual Sabrent 4-Port USB 3.0 Hub.

The thin, lightweight design makes the Sabrent 4-port USB 3.0 hub a great travel companion to expand your laptop’s USB 3.0 port into four.

Fully backwards compatible with the USB 2.0/1.1 products.

Additionally, each port has its own power switch, allowing for individual port control.



With SuperSpeed USB 3.0, you can now transfer data at up to 10 times the speeds of the older USB 2.0 standards.

Speeds of 5Gbps are a vast improvement over USB 2.0’s 480Mbps top speed.

The Sabrent 4-Port USB Hub utilizes the most advanced technology,

but it is also backwards compatible, allowing you the capability of using USB 2.0/1.1 products if need be.



System Requirements:

• Windows 2000/XP/Vista/7/8/8.1/10

• Mac OS 9.1 & Higher

• Linux 2.4 or Above



Please Note:

2.4Ghz wireless devices, such as wireless keyboard and mouse adapters, may not work in close proximity to USB 3.0 devices or hubs.

Connecting to a USB 2.0 port is recommended.



For a stable connection, the devices connected to the 4-Port USB 3.0 Hub must not exceed a combined current of 5 volts 900 mAh.

External hard-drives should be connected to an external power source.

This 4-Port USB 3.0 Hub will not charge your devices, it will only sync.



Package Contents:

• USB 3.0 Hub (built in)cable

• EXPANSION: Instantly add 4 USB 3.0 Ports to Any compatible device. Transform a single USB port into a full work station. The extended 2 ft cable allows for the perfect set up and easy access to out of the way ports.
• CONVENIENCE: LED Indicators display power status for each port. Individual on/off switches enable you to easily connect and disconnect your devices with the push of a button.
• SUPER SPEEDS: Supports transfer speeds up to 5Gbps (USB 3.0), 480Mbps (USB 2.0), & 12Mbps (USB 1.1). Fast enough to transfer large files in seconds.
• COMPATIBILITY: Reverse compatible with USB 2.0 and USB 1.1 devices. Use with PC, MacBook, iMac, Mac mini, XPS, Flash Drives, & any other USB compatible devices.
• EASY SETUP: No driver installation required; Plug & Play and Hot Swappable. Does NOT support charging.

User questions & answers

Question:	I have 2 external hard drives: 1 is 500 GB, 1 is 2 TB. Both have their own power cords. Will they work with this hub
Answer:	yes they will, I have a 3 tb WD, a 2 tb Fatom,and a 1tb HP they all work fine, and and any thumb drive that I plug in syncs right up.Some of the thumb drives are usb 2.0 , no problem
Question:	What is the recommended ac adapter to use with this
Answer:	JTJ said he didn't have a power jack. Either there is more than one version or he has one but didn't find it. It would be easy to miss. It's next to the USB cable. For basic devices, like a mouse, keyboard, etc, you do not need a power supply. The computer will power them, but the current the computer will supply is limited. If you plan to charge a smart phone, tablet, or something like that you should make the adapter part of your plans.(http://www.amazon.com/Sabrent-100V-240V-Adapter-Support-PS-5V4A/dp/B00MRGKPH8 )
Question:	If I plug this into a 2.0 USB port on my CPU, will I still get the benefit of Sabrent's 3.0 speed? Or is it about time I update my motherboard? Thanks
Answer:	@T. Freese: No. The nature of USB is that devices can not communicate among themselves. All communication goes through the host computer. So a pair of 3.0 devices sharing a hub attached to a 2.0 computer will communicate at 2.0 speeds.
Question:	Does the fact that each has a switch mean that you can just turn each of them off without doing "safely remove" or "eject" devices
Answer:	The reason that you use the Windows Option to safely remove the drive is so that windows has a chance to close any File Pointer that is in use. If this is not done, then there is a chance that the file(s) will be locked and/or corrupted the next time the drive is accessed.So. It is recommended that you safely remove the drive before you hit that power switch on the hub.I have this hub and use it to access 1 4TB drive, 2 5TB drives and 1 8TB drive. That is a LOT of data to loose just because I got lazy.The one reason to have switches on a hub is so that you can have the drives OFF when not in use. This will save some life on the hard drive.Lance

Product features

Product Description

Add up to 4 devices with the Sabrent 4-Port USB 3.0 Hub. The thin, lightweight design makes the Sabrent 4-port USB 3.0 hub a great travel companion to expand your laptop’s USB 3.0 port into four. Fully backwards compatible with USB 2.0/1.1 products. Furthermore, each port has a power switch, allowing for individual port control.

With Super-Speed USB 3.0, you can now transfer data 10 times faster than older USB 2.0 standards. Speeds of 5Gbps are a vast improvement over USB 2.0’s 480Mbps top speed. The Sabrent 4-Port USB Hub utilizes the most advanced technology but remains compatible with the older USB 2.0/1.1 standards.

Please Note:

2.4Ghz wireless devices, such as wireless keyboard and mouse adapters, may not work in close proximity to USB 3.0 devices or hubs. Connecting to a USB 2.0 port is recommended.

For a stable connection, any device connected to the 4-Port USB 3.0 Hub must not exceed a combined current of 5 volts 900 mAh. External hard-drives should be connected to an external power source. This 4-Port USB 3.0 Hub will not charge your devices, it will only sync.

Easy To Setup: Plug & Play and Hot Swappable

Blue LED indicates power status for each port.

Supports Transfer Speeds up to 5Gbps

Reverse compatible USB 2.0 and USB 1.1.

Superior Industrial Quality

Enables users to seamlessly transfer data.

Compact Design

Perfect for traveling and taking on the road.

Product description

TP-Link UH720 is a 9-port USB hub. 7 USB 3.0 ports can be used for data sync and 2 ports are dedicated for quick charging. It also come with a power adapter to provide robust performance and a power on/off button to conveniently turn on/off the hub as need.



With TP-Link UH720, you can now transfer data at up to 10 times the speeds of the older USB 2.0 standards. Speeds of 5Gbps are a vast improvement over USB 2.0’s 480Mbps top speed. It is also backwards compatible, allowing you the capability of using USB 2.0/1.1 products if need be.



UH720 is Plug & Play for Windows, Mac, Linux, Chrome OS and more PCs, no driver installation required.



Please Note: 2.4Ghz wireless devices, such as wireless keyboard and mouse adapters, may not work in close proximity to USB 3.0 devices or hubs. Connecting to a USB 2.0 port is recommended.

The non-charging ports are intended for data transfer only. They provide insufficient power output for charging. And the charging port are for charge only, will not work for data sync. Ensure that the adapter is connected before using this hub. And for best performance please connect it to the USB 3.0 port of your PC." Interface Available: 7 USB 3.0 Standard A 2 2.4A Charging Ports, 1 USB 3.0 Micro B

• Faster Speed with USB 3.0: USB 3.0 ports offer transfer speeds of up to 5Gbps, 10 times faster than USB 2.0. This 7-port USB 3.0 data hub can instantly expand 1 USB 3.0 port to 7 external USB 3.0 data ports for keyboard, mouse, printer, hard drivers and other USB devices.
• Smart Charging Ports: 2 Extra 5V/2.4A charging ports supporting 2.4A output specially designed for ultra fast charging. Charges most USB charging equipment, regardless of large batteries such as smartphones or tablets, or mini-battery equipment such as smart portable devices, at full speed.
• TP-Link Charging technology intelligently identifies connected devices, automatically delivering the fastest charge to your smartphones, tablets or devices with a USB charging connector, minimizing charging time.
• Protect Both Your Equipment and Your Data: UH720 has a sophisticated circuit design with multiple overheat, overload, overvoltage and short circuit protections. A built-in surge protector keeps both your devices and your data safe in the data transfer process.
• UH720 supports hot-swap USB ports that can be safely connected and disconnected while the computer is on and running.
• Plug and play: No drivers required for Windows 8.1 / 8/7 / Vista / XP or Mac OS X and Linux systems. Backward compatible with USB 2.0 / 1.1 and current transmission speed is limited by the settings of the connected device
• Manufature's 2-year warranty and 24/7 technical support
• To be eligible for TP-Link's Warranty, please confirm and purchase from "Sold by Amazon"

User questions & answers

Question:	Can USB 2 connections be used with this
Answer:	Yes it’s backward compatible
Question:	If I select one of my ext hard drives which appear in system preferences > startup disk the machine still starts with my iMac hd. What is wrong
Answer:	Try this, Turn on your Imac and wait for the boot sound, as soon as you hear the sound press and hold OPTION key. If you miss it , try it shut it down and turn it back on again. By pressing option key on startup will show all the accessible hard drives with operating system on it , so you can choose the one you wish to boot from.
Question:	what are the dimensions of the box itself and how long is the power cord
Answer:	The size of packing is 4.33 x 3.39 x 8.23 (inches), the size of product is 2.58 x 0.69 x 6.50 (inches), the data cord is 40 inches long, and the power cord is around 60 inches long
Question:	Anyone with the UH720 model - do the high-powered ports support data transfer
Answer:	No data on the high powered ports, and I consider that a bonus. It means I can now charge devices that don't have data transfer features. I have some devices (battery chargers, quad copters, other devices with internal batteries) which when plugged into USB data transfer ports cause an error and a beep from the computer that persists every 2 seconds. With these charge-only ports I can now charge any device at my computer desk.

Product features

Increase the Number of Available Ports

The UH720 is perfect for everyone who has a computer with one or two USB ports and wants easy access to additional ports without having to change equipment.

* Many laptops only have one or two ports

* Many computers have hard-to-locate USB ports

10x Data Transfer Speed

Equipped with USB 3.0 ports, the UH720 can transfer 1080p movies in 2 minutes 18 seconds, while it takes 7 minutes 36 seconds with a Hub with USB 2.0 ports. The actual transmission speed depends on the settings of the connected device.

Two Extra Charging Ports for All Your Devices

Two extra USB ports supporting 2.4A output specially designed for ultra fast charging. Charges most USB charging equipment, regardless of large batteries such as smartphones or tablets, or mini-battery equipment such as smart portable devices, at full speed.

Protect Both Your Equipment and Your Data

The UH720 has a sophisticated circuit design with multiple overheat, overload, overvoltage and short circuit protections. A built-in surge protector keeps both your devices and your data safe in the data transfer process. UH720 supports hot-swap USB ports that can be safely connected and disconnected while the computer is on and running.

Product description

Search "How To Hardwire A Car dash camera" in Youtube and check the instructional video from dial2fast to find out how it works. The NuCam Hardwire Fuse Kit with Micro USB Bundle has everything you need to charge your dash cam, cellphone, tablets or other devices from your car’s battery even if your engine is off. It has low voltage protection so that you can use to power your dash camera 24/7 without draining your battery to dead.If you’re worried about someone breaking into your car when it’s in the parking lot, you can use our NuCam DL and set it to parking mode so that it will be on and ready to record. The Dash Cam Hardwire Kit keeps your 12V outlet free, so you can keep your phone charged and power your dash camera at the same time. It also means that there’s less RF interference or static when you’re listening to the radio. You can play your favorite station without losing the signal.



What’s Included:



1 x MicroUSB Hard wire Kit

1 x Low-Profile Mini Fuse Holder

1 x Mini Blade Fuse Holder

1 x ATO (regular) Fuse Holder

1 x Micro2 Fuse Holder

1 x MicroUSB - Type C adapter

1 x Fuse Puller

1 x MicroUSB - MiniUSB adapter (left angled miniUSB. If you are looking for right angled miniUSB, please search B0787LD92N.)

* If your kit is missing any of the above adapters, contact Nuvending California office with your order # so that we can provide the correct adapter.

Features :

Hardwire kit for dash cameras that use micro USB/Mini USB

Works with NuCam DL, K1S, Zero Edge, DDpai, Goluk and more!

24 hour surveillance protects against battery dying with parking mode.

Keeps 12V cigarette outlet free

Does not alter original wiring. Easily installs on the existing circuit Install, looks clean and professional

Gives power to a number of electronic devices up to 5V/2A.

Extra length of hard wire allows you to connect to the fuse box under the hood: input length: 3ft, output length: 12ft

• ONE FITS FOR ALL: With Micro to Mini and Micro to Type C port converters, the kit is basically fit for ALL Dash Cams or Car Charger like NuCam DL, Wireless Charger Phone Holder Nucharger Auto, Rexing, ROAV, Zero Edge, Anker, DDPai, Papago etc(not compatible with Garmin). Also, it comes with most popular fuse types including Low-Profile Mini, Mini, ATO(Regular), and Micro2. It has both left handed and right handed mini USB adapters.
• ENOUGH LENGTH: Overall 15ft hardwire kit can be installed basically on All vehicles. Input length: 3ft, Output length: 12ft.
• BATTERY DRAIN PROTECTION SYSTEM: For our 2019 updated version, we increased our cutoff voltage from 11.6V to 11.9V to protect vehicle battery voltage from dropping below 11.9V and not starting up. It’s also suitable for 24V systems.It is recommended to turn on parking mode for your dash cam to save your battery power. Find another listing B0787LD92N if you need different or adjustable cutoff voltage.
• EASY INSTALLATION: Installation is easy and clean without any help from professionals! However, our customer service is also immediately responsive if you do have questions.
• WARRANTY: One year free service for any question you are facing with this dash cam hardwire kit.

User questions & answers

Question:	This product has a ground wire. Does it have to be grounded? Aren't the fuses/fuse boxes already grounded
Answer:	The fuse box is at the positive. You can connect to any screw in the metal frame to get grounded.
Question:	There is a comment below were someone had gotten a longer length cord after contacting you, is there a listing for that version
Answer:	Yes the new version will come with 15ft long cord. It will be available in our next shipment to Amazon under the same listing. If you need one urgently, you can contact us at Nuvending website with your order ID then we will send one to you for free from our California warehouse.
Question:	The picture shows with the check mark a left angled mini usb, but the label says right angled. Which is which
Answer:	I think it depends on which symbol you want to use as a check mark. In the third picture for this product listing, the left one with X is a left angled mini USB which is not included in this hardwire kit. The right one is the correct one which is a right angled one included in this product. I know in the US sometimes people use X as a check mark. But when we have V coming out, X just means the wrong one, or not available. Maybe we should use a circle with slash instead a X as not available?
Question:	Can this work for using echo dot in the car
Answer:	That sounds like a fantastic idea. But can you tell me more detail about what you like to do with the echo dot? The microUSB terminal should be able to charge echo dot or other device with microUSB port with your car battery. I assume you need to have internet to use echo dot, right?

Product features

MicroUSB, MiniUSB Dashcams and Mobile Devices

With Micro-to-Mini and Micro-to-Type C port converters, this kit will work for ALMOST ALL Dash Cams like NuCam DL, Rexing, ROAV, Zero Edge, Anker, DDPai, Papago or other device such wireless car charger Nucharger Auto etc. Or use it to charge most of your Android mobile devices without the need to turn on your engine!

Wires with Length

With an Input length of 3 ft. and an Output length of 12 ft., this hardwire kit stretches a total of 15 feet! The hardwire kit can be installed virtually on any vehicle with room to spare.

Easy Clean Installation

A pretty straightforward install without the hassle and confusion of too many wires and connections, results in a professional finish.

Four Fuse Adapters

Comes with ACZ(micro2), ACS(mini), ACN(LP-mini) and ACU(ATO) fuse adapters for you to use whatever your vehicles fuse box requires.

Two Connector Types

The most versatile hardwire kit in the market comes with a MiniUSB connector which makes routing your wires when installing a lot easier. Plus it also comes with a Type-C USB connector for Android devices!

Battery Drain Protection

The hardwire kit is "wired" to power off your device when the vehicles battery voltage drops below 11.6V to save you power needed to start your engine (12.0V higher cutoff voltage version is available upon request). The kit is also suitable for a 24V system.

Product description

An Amazon Brand

• Package includes: 1 USB 3.0 4 Port Hub / 1 5V/2.5A Power Adapter / 1 built in 9 inch USB 3.0 cable / 1 Owner's Manual
• Compatible with USB 3.0 and backwards compatible with USB 2.0
• Support Low speed (1.5 Mbps)/ Full speed (12 Mbps)/High speed (480 Mbps)/ Super speed (5 Gbps)
• Support auto switching between self-power and buspower mode
• Check your device loading current when used for charging (e.g. iPads/Tablets) or for high-power devices (e.g. hard drive); insufficient current may lead to slow charging or other failure
• Max output per port is 900MA; max output across all 4 output is 12.5W(5V/2.5A)
• For maximum output, apply power adapter

User questions & answers

Question:	can you run this USB hub witout power
Answer:	It depend om what is connected. Mice and Keyboards and some HDs have either batteries or a power supply but I would not hook up one of the portable "2.5" drives, which are really metric 60 mm not 2.5 inches. The power from the USB depend on the port. Not all ports supply a charging voltage. You source port would need to supply the proper energy if you did not use it. A memory stick his no power source, a larg one would be th most likely object to fail besides the previously mentioned drive.
Question:	Are all the ports USB 3 ports? On the side, there are 2 ports labelled "Fast", and then 5 others that are not fast. Are they not all the same speed
Answer:	If u have the one with 2 times "fast" written on the side it is the 2.0 USB hub. the 3.0 Hub has blue connectors and all the 3 at the front are fast chargers with Flash sign next to it. The wall charger Comes as by Derek Ng as a 3A charger but 12V - 3A which gives complete 7.2 Amps total and meassured at my usb3.0 Hub it gives out 2.4A 5.2V and charges my iPad 4 without Problems. The stream-speed of the ports are all the same Speed (depending if u have USB2.0 Version i reached 430 Mbit/s at the USB 3.0 Version i reached 4200 Mbit/s but thats all my PC can manage so it might go faster if ur PC is faster) Hope i was able to help.
Question:	Can someone who already purchased this item write what it says on the adapter next to the input line
Answer:	INPUT: 100-240V~50/60Hz 0.5AThis should work anywhere in the world with the proper plug adapter.
Question:	What exactly does "auto switching between self-power and buspower mode" mean? Thanks
Answer:	The 7 port USB device listed above is a "Self Powered" device. It gets its power from an external connection to the power lines, usually as a small transformer plugged into a wall socket. The "bus powered mode" is when a USB device gets its power directly from the USB port of the computer or other upstream device. "Auto switching" means that the electronics in the self-powered device can, on loss of its external power, switch to conformance as a bus powered device. This may mean electronically disconnecting devices plugged into its ports until the total load on the upstream USB port is no more than one unit load, or 100 milliamps.Seehttp://www.beyondlogic.org/usbnutshell/usb2.shtmlThere are three classes of USB functions, Low-power bus powered functions High-power bus powered functions Self-powered functionsLow power bus powered functions draw all its power from the VBUS and cannot draw any more than one unit load. The USB specification defines a unit load as 100mA. Low power bus powered functions must also be designed to work down to a VBUS voltage of 4.40V and up to a maximum voltage of 5.25V measured at the upsteam plug of the device. For many 3.3V devices, LDO regulators are mandatory.High power bus powered functions will draw all its power from the bus and cannot draw more than one unit load until it has been configured, after which it can then drain 5 unit loads (500mA Max) provided it asked for this in its descriptor. High power bus functions must be able to be detected and enumerated at a minimum 4.40V. When operating at a full unit load, a minimum VBUS of 4.75 V is specified with a maximum of 5.25V. Once again, these measurements are taken at the upstream plug.Self power functions may draw up to 1 unit load from the bus and derive the rest of it's power from an external source. Should this external source fail, it must have provisions in place to draw no more than 1 unit load from the bus. Self powered functions are easier to design to specification as there is not so much of an issue with power consumption. The 1 unit bus powered load allows the detection and enumeration of devices without mains/secondary power applied.

Product features

Use Anywhere

USB hubs offer an ideal way to connect multiple devices virtually anywhere you need fast, handy access to USB connection. Multiple sizes available.

Connect Devices

Easily connect digital cameras, iPods and iPhones, card readers, USB speakers, and more with this plug-and-play portable USB hub.

Compatibility

Check your device loading current when used for charging (e.g. iPads/Tablets) or for high-power devices (e.g. hard drive). Multiple types available.

Additional Features

Includes over-current protection and bus-powered (without power adapter) and self-powered (with power adapter) modes.

Product description

Add a permanent USB port to your vehicle or camper with a hardwire, mounted unit by Custom Accessories. This unit direct connects into you 12VDC system. Includes an under dash mounting bracket and has a built-in automatic overload reset system.

• Flush mount USB port charger is the permanent solution to making sure your electronic devices always have a full battery
• USB port charger outputs 5VDC up to 2.1 amps for quick charging
• Designed with a built-in automatic overload reset system to protect your electronic devices
• Mount under the dash for quick installation
• This unit direct connects into you 12VDC system

User questions & answers

Question:	how big is the cable
Answer:	Yes it fit the nubribullet 600w & 900w blender
Question:	Does this convert 12v to 5v output at the usb?does this convert 12v to 5v output at the usb
Answer:	No center hole. There are three rings each with its own air valve. I dont usually clime on from the water. It has a rope so I think it would be easy to climb on from the water.
Question:	Will this work with Android Auto
Answer:	It's pretty sturdy but not so thick that it won't easily pop. It holds a lot of weight. The only thing I didn't like about this raft was that sun tan lotion from my body turned it very sticky! I'd buy this raft again. Wind caught mind and threw it in a barbed wire fence which eventually made me throw it out instead of patching it.
Question:	Will this hub work when I plug it to my wireless mouse usb on my Mac Pro
Answer:	It is like 3 inner tubes but connected of course. Water does lay in those but it is light & easy to flip the water out when preferred.
Question:	Is this unit easy to use
Answer:	Husband weighs 255 Lbs and holds him AND me (115) no problem.
Question:	Is it compatible with Microsoft Surface 2 Laptop
Answer:	I got an air pump at walmart it is like the ones you use to blow up air mattresses with it was in the camping department. It says you can blow it up with a hair dryer set on cool air.
Question:	Do I need to step down the 12v usb inputs to 5v for phone charging
Answer:	No screen protector, but it does allow the tablet to sit in the case about a 1/4". The corners are under the case, so they are well protected. I have a wild 2 year old that uses one and we haven't had any issues with cracks or breakage.
Question:	does it come with screws
Answer:	Sure,if you want to buy the light engine only with fiber,please check by ASIN: B073CQCD4S. You wil get what you need.Please check and let me know freely if anything else we could help. Thank you^^
Question:	Does this come with a cap/cover for the 12 volt socket
Answer:	Hi dear, the stock is on its way now and will be available for sale in 7-10 days. And you could send us inquiry via message freely or directly place an order and choose fulfilled by SHINE. We will ship out your order via DHL express and it will reach you in 7-10 days. Thank you!
Question:	questions: the description does not mention that the unit has an led light. some of the reviews says that there is a blue light. which is it
Answer:	I used two sets to install in an 18' x 10' space in my theater room. One set wasn't long enough to fill the total space. Having two sets means the two halves aren't in synch. But it absolutely is long enough for a home ceiling, and it looks really good.

Product features

Sabrent Premium 3-Port Aluminum Mini USB 3.0 Hub

• Sleek apple-style design, ideal for Mac Pro, iMac, MacBook Air, MacBook Pro, MacBook, and Mac Mini.
• Usb connector can be rotated 90°/180° degrees.
• Portable, compact, lightweight design makes it travel friendly.
• Easy setup, plug-n-play, hot swappable, hot Pluggable.
• Compatible with Windows/Mac/Linux systems.

Easily add up to three devices with the Sabrent USB 3.0 rotatable hub. Effective for all computers and laptops and particularly those that come with a limited number of ports. Avoid interchanging your USB-devices and having to decide between synchronizing your phone or working with your external hard drive. By utilizing the Sabrent USB 3.0 rotatable hub, you can employ all of your devices at once.

Note

2.4GHz wireless devices, such as wireless keyboard and mouse adapters, may not work in close proximity to USB 3.0 devices or hubs. Connecting to a USB 2.0 port is recommended.

For a stable connection, The devices connected to the 3-port USB 3.0 hub must not exceed a combined current of 5 Volts 900 mAh. External hard-drives should be connected to an external power source. This 3-port USB 3.0 hub will not charge your devices, It will only sync.

Product description

Brand new hardwire car charger kit for Garmin Nuvi series GPS. This ultra compact 2nd generation hardwire kit comes with a 90 degree mini USB connect is an ideal hardwire kit for your car and bike. fit Nuvi 1200, 1250,1260t, 1300, 1300LM, 1350, 1350T, 1370T, 1390LMT, 1390T, 1450, 1450LMT, 1490LMT, 1490T, 200, 200W, 200, 205W, 2200, 2250, 2250LT, 2300, 2300LM, 2350, 2350LMT, 2350LT, 2360LMT, 2360LT, 2370LT, 250, 250W, 255, 255W, 260, 260W, 265T, 265WT, 270, 275T,295W, 350, 360, 370, 465T, 500, 550, 30, 40, 50, 50LM, 010-10723-06, GTU 10 GPS locator

• ⚠️This is a direct hardwire cable kit, vehicle installation is needed, For GPS with mini USB port powering.
• Works with Gramin Drive 50 50lm 51 50lmt USA EX 51lm 51lmt-s 60 60lm 60lmt 61 61lm 61lmt-s; DriveSmart 50 50lmt 50lmthd 60 60lmt 60lmthd 51 51lmt-s 61 61lmt-s 70lmt; DriveAssist 50lmt; DriveLuxe 50lmthd 51lmt-s
• Garmin Nuvi 52lm 55lmt 56lmt 57lm 58lmt 65lmt 66lmt 67lm 68lmt 2455 2455lmt 2457 2457lmt 2495 2495lmt 2497 2497lmt 2539 2539lmt 2555lmt 2557lmt 2559lmt 2589 2589lmt 2595lmt 2597 2597lmt 2599 2599lmt 2557 2557lmt 2577 2577LT 2597lmt traffic built in GPS
• For Nuvi 1200, 1250,1260t, 1300, 1300LM, 1350, 1350T, 1370T, 1390LMT, 1390T, 1450, 1450LMT, 1490LMT, 1490T, 200, 200W, 200, 205W, 2200, 2250, 2250LT, 2300, 2300LM, 2350, 2350LMT, 2350LT, 2360LMT, 2360LT, 2370LT, 250, 250W, 255, 255W, 260, 260W, 265T, 265WT, 270, 275T,295W, 350, 360, 370, 465T, 500, 550, 30, 40, 50, 50LM, 010-10723-06
• Space saving 90° mini USB connector, regulator box size is about 45mmx23mm, 12V~24V direct DC power input, 5V 1200mA output, LED power indicator. Great GPS accessories, about 10' in length with heavy duty cable, 30 days money back, one-year replacement warranty from EDO Tech Supply

User questions & answers

Question:	Will this work with a garmin nuvi
Answer:	same here- hello Amazon- please remove the lifetime warranty info as it doesn't seem to exist
Question:	Nuvi 2597 LMT and it keeps displaying that cable is not compatible with traffic feature. I have it turned off. Garmin says the cable is no good
Answer:	No they do not. I move mine from portrait to landscape often. The rubber comes off. Get what you pay for on this one. Cheap
Question:	Will this hardwire allow the unit to run at 100% brightness? most usb hardwires and dual usb ports only get the unit to 70 or 40% screen brightness
Answer:	NO
Question:	Can the wire between the transformer and the usb plug be shortened
Answer:	Any rectangular 16x32 foot pool

Product description

Add up to 4 devices quickly and easily with the Sabrent USB 2.0 Rotatable Hub.

Great for newer notebooks that come with a limited number of ports.

Maximize your time by obtaining access to plug in multiple USB devices instead of having to choose just one .

Achieve full 480 Mbps on each port, or daisy-chain multiple hubs to a maximum of 127 devices.

Fully backwards compatible with the USB 1.1 products.



Please Note:

For a stable connection, the devices connected to the 4 Port Hub must not exceed a combined current of 5 volts 500mAh. External hard-drives should be connected to an external power source. This 4 Port hub will not charge your devices, it will only sync them.



Package contents:

• Sabrent Rotatable 4 Port USB 2.0 HUB

• Lightweight design enables the hub to be compact and portable. CHARGING NOT SUPPORTED.
• USB Connector Can be Rotated 90°/180° Degrees
• Easy Setup, Plug-n-Play, Hot Swappable, Hot Pluggable
• Compatible With all Windows/Mac/Linux Systems
• Instantly Add Four USB 2.0 Ports to Any Compatible Device

User questions & answers

Question:	Only works on my laptop, will not work on a usb from my cigarette lighter adapter. what's up
Answer:	Ot is not a power hub. I used mine on my laptop only for connecting devices. It atopped working in 6 weeks. No reply from company when i complained
Question:	So you can use this as a regular usb port, such as plugging my mouse / keyboard in it
Answer:	Yeah, that's what I use it for anyways. Since I only have 2 USB ports on my laptop, all my ports are used up most of the time so this makes it easier.
Question:	Will this charge 4 Iphones at same time
Answer:	It says in the description "For a stable connection, the devices connected to the 4 Port Hub must not exceed a combined current of 5 volts 500mAh. External hard-drives should be connected to an external power source. This 4 Port hub will not charge your devices. (it will only sync)." your phone might accept 500mAh but it's about 25% (slower actually) of what your phone wants / needs, especially if it's a newish phone =P
Question:	I'm using this in my car. Will this draw power when the car is off? I saw the blue light still on even though the car is off... will my battery die
Answer:	If your outlet is live, even when the isn't operating, it will draw power. Will it be enough to drain your battery? Try it and see. Unless your battery is nearly done, or you're powering something that has a high draw, I would say no, but that's no guarantee.

Product features

Add up to 4 devices with the Sabrent USB 2.0 Rotatable Hub.

Maximize your time by gaining the ability to plug in multiple USB devices instead of having to choose to use just one at a time . Achieve full 480 Mbps on each port.

Fully backwards compatible with the USB 1.1 products.

Please Note:

For a stable connection, the devices connected to the 4 Port Hub must not exceed a combined current of 5 volts 500mAh. External hard-drives should be connected to an external power source.

This 4 Port hub will not charge your devices, it will only sync them.

90°/180° Rotation

Adjustable For Any USB Ports Location.

Technologically Designed For Any Device

Offering USB Connectivity For Multiple Devices.

Superior File Transfer Speed

Allows You To Smoothly Transfer Your Data.

Enabling Four Additional Ports

With Plug-Play Ability, You Instantly Gain More Device Access.

Product description

Corrosion resistant materials to ensure solid contact and low voltage drop - 1

• Charge two mobile devices on the go
• Fits in same mounting hole as a traditional 12V outlet
• Compatible with most mobile devices including Apple products
• Manufacturer Part Number: 1016-BSS
• Quantity: 1 per package

User questions & answers

Question:	is it fused or do i need a fuse
Answer:	Time is about 1-1/2" and the date is about 1/2". You should be able to read the numbers from 20 ft away.
Question:	Does this work to charge an iphone5? (I just want to ensure Apple hasn't cooked up some proprietary signal
Answer:	NO NO NO NO NO NOT lighted and difficult to read. I have the clock on the wall, this moment, at a distance of two yards, and it is readable but barely. It has DARK GREY LED background and black letters, poor poor contrast.
Question:	This is a Cigarette Lighter Socket right
Answer:	The whole unit is 7" x 9" and it has a 6" in screen (3.5" x 5"). It's not huge, but a good size. Im looking at it right now on the bookshelf in my office and I can tell you that it's smaller than an 8x10 picture frame but bigger than a 5x8 frame. Hope this helps.
Question:	what size fuse should i use
Answer:	It’s not safe at all. I was making green juice & it broke. Everything splattered everywhere. Bbtoke from the top round.

Product features

Customizable

The blank panels provide complete customization allowing you to design the panel to fit your specific needs.

Mini OLED Voltmeter

Monitor your voltage on a bright, waterproof, daylight readable OLED screen.

Prevents Parasitic Draw

The Illuminated Carling Technologies 15A circuit breaker switch allows the ability to shut off the panel.

Easy to Install

Pre-wired harness included in all panels for easy installation.

• Wish you had more USB Ports? Aduro 4 Port Car Charger Adapter charges four devices simultaneously - works for USB-Powered devices such as iPhone Samsung iPad
• Smart charge technology maximizes both compatibility and charging speed, with LED lights to confirm charger is properly connected
• We designed this quad car charger adapter with advanced full aluminum alloy body and safe Anti-overheat features to the UL standard
• Aduro car charger USB cigarette lighter splitter adapter provides powerful output of 5.2A max with smart IC charge technology
• Why choose Aduro? Because we back our USB car charger with A lifetime limited warranty and friendly 24/7 US customer service, so you can buy it with confidence and have complete peace of mind

User questions & answers

Question:	Can i use the ports for items that do not need charging
Answer:	The package says “all water based paints & stains”, so it depends in the type of lacquer. If it is oil based, no.
Question:	Is the charger compatible with older model vehicles? I have a 2003 toyota highlander
Answer:	The innermost ring will fit some pint cans. I have personally used it that way.
Question:	Does this work with Samsung galaxy s20 plus and Motorola
Answer:	The lid comes on and off easily. If the paint needs to be stirred, peel the lid off, stir it and put the lid back on. I usually take the lid off after each use and clean it. Then put it back on when I use the paint again. The lid cleans very easy that way.
Question:	Does this work for a Samsung galaxy Tablet
Answer:	Have you tried replacing the battery s? I use the batteries with a 10 year life. They cost a little more but worth the price.

Product features

Aduro Four Port Car Charger Adapter

Charges four devices simultaneously with LED lights to confirm your phone is charging. Safe anti-overheat and smart charge technology feature, it charges your phone at max speed.

Product description

Each lighter has a bottom stamp signifying the year it was made, is refillable, and is backed by Zippo’s famous lifetime guarantee. All windproof lighters are American made in our Bradford, PA factory and come packaged in a gift box.Each light has a bottom stamp signifying the year it was made, is refillable, and is backed by Zippo’s famous lifetime guarantee. All windproof lighters are American made in our Bradford, PA factory and come packaged in a gift box.

• Material and Appearance - Aluminum Alloy is the main materials Silica gel and plastic are auxiliary material The architecture conforms to international standards Clear lines and exquisite shape Hard to be scratched
• Safety and Convenience - Intelligent IC design and Quick Charge 3 0 technology make the current transmission more stable Already obtained the CE, RoHS and WEEE certificate (NOTE Quick charge function needs to use the original charging cable)
• Function and Parts - Dual USB port design LED voltmeter can track the voltage of cars and devices the design of the cap makes the product dustproof and waterproof Present a pair of extension cords (23 63”/20CM 10A fuse lines)
• Application and Compatibility - Fits for DC 12/24V car boat marine motorcycle marine truck ATV RV etc This USB power outlet is suitable for charging iPhone 8/ 8 Plus/ X/ 7/ 6S Samsung Note 9/ Galaxy S9/ S9+/ S8/ S8+/ S7 iPad android tablets power banks video games controllers sports watch etc ( NOTE iPhone series does not support fast charging charging the iPhone is normal speed )
• And Installation - 12 months period High toughness PC housing and intensify nut keep off, slipping Cigarette lighter socket replacement "+" is plugged into positive pole and "-" is put on negative pole It can also be connected to an on/off switch to save energy

User questions & answers

Question:	What's kinds of devices suit the quick charging 3.0 version function
Answer:	We have both version. You will receive what you see as in the sales link.
Question:	Why it’s out of work? What’s wrong? I have received a defective one
Answer:	Yes
Question:	Do i need the in line 10amp fuse if i use the existing two wires from my cigarette lighter
Answer:	Yes, each Metakoo Torque Screwdriver has been calibrated precisely before being shipped from our factory. In the package, you will see the certificate of conformance in accordance with ISO6789-1:2017.
Question:	Hello, does the blue light stay on all the time? Will ittoo bright at night
Answer:	The drill bit can be moved in and out so I believe this will accommodate a 1.5" pilot hole. If not it will be very close to 1.5".

Product features

USB Socket Specifications:

Net Weight: 55G

MAX Power: 36W(18W each)

Input: DC5V-DC32V

Waterproof Rating: IP66

Ordinary Output: 5V2.4A*2 5V3.4A*2 9V2A*2 12V1.5A*2

Material: Aluminum Alloy + PC +Silica gel

Operating Temperature: -40℃ to 140℃

Portiforium Dimension: 29mm

USB Port: Quick charge 3.0 + 5V/2.4A USB port

Smart IC Technology

Make the current transmission more stable, outlast use.

A Pair of Wiring and Spade Terminals

Lines with 10A fuse and extra connect terminals make install and protect easy.

High Density Silicone Cap

The design of the cap makes the product dust-proof and waterproof.

Wide Device Applications

It’s suitable for charging phone, iPad, charging bank power, humidifier,fan etc.

Quick Charge 3.0 Version

QC 3.0 is up to 4-6°C, 16% faster and 38% more efficient than QC 2.0.

Application Scenario Widely

Suit for car, motor, ship, crane, truck, yacht, van, RV, etc.

Product description

Trendnet’s USB 3.0 to Gigabit adapter + USB hub, model TU3-ETGH3, adds a Gigabit Ethernet port and three 5Gbps super Speed USB 3.0 ports to a Windows or Mac computer. The USB adapter and Hub Combo offers easy installation – simply plug in flash drives, printers, scanners and other USB 3.0 devices at speeds ten times faster than a USB 2.0 connection. The TU3- Etgh3 is also compatible with USB 2.0 and 1.1 devices.





usb 3.0

easily connect up to three USB 3.0 devices to a USB 3.0 enabled desktop or notebook PC.





gigabit speeds

experience full duplex 2Gbps connection speeds with this USB 3.0 Gigabit adapter.



compatibility

the USB adapter and Hub combination is compatible with Windows and Mac operating systems.





package contents> tu3-etgh3



quick installation guide



CD-ROM (driver & User's guide)

• 1 x Gigabit Ethernet port
• 3 x USB 3.0 ports
• Windows and Mac compatible
• Flexible USB 3.0 cable accommodates most installations
• Backward compatible with USB 2.0 and 1.1 devices
• Supports wake on LAN (suspend mode)

User questions & answers

Question:	Does this work with Chromebooks
Answer:	I wouldn't call it a rip off but it is exactly like some blender bottles. The utility patent is for the use of the "blender bottle" for storing paint.
Question:	does it come with the optional power adapter for power hungry devices
Answer:	I’ve thrown away the can but I used it to paint a mailbox post and it looks fine to me. It’s not really shiny if that tells you anything. I have no idea what low-voc is, sorry.
Question:	Where is the chipset for trendnet 3-port usb 3.0 hub ? asix ax88772(a) or other ? i want to deploy pxe hp spectre x2 only with ax88772a chipset
Answer:	Yes, if you're just painting the desktop.
Question:	Does this support Nintendo switch? Because it is not working. (it is in usb port
Answer:	I think you are supposed to use them for only waterbased paints. I'm not sure how they will last for waterbased paints, but I can tell you that they do not work foe solvent based paints. I could not get them seal pn the cans, even though it looked like they were going to work. I would not buy them again.

Product features

Gigabit Ethernet

Adds a Gigabit Ethernet port

USB 3.0

Easily connect up to three USB 3.0 devices to a USB 3.0 enabled desktop or notebook PC

Installation Flexibility

Integrated 14cm (5.5 in.) USB 3.0 cable accommodates most installation scenarios.

Operating Systems

Compatible with Windows and Mac operating systems