Product description

The Scosche SLC4 4-channel adapter line out converter for car stereo audio allows you to connect a receiver with no pre-amp outputs to an amplifier without speaker-level inputs. The SLC4 handles a speaker-level signal up to 80 watts RMS per channel, then converts it to a line-level signal you can plug into your amp's input. This speaker wire to RCA speakers converter is compatible with high power car stereos up to 80 watts per channel. Perfect for fast installation when adding a subwoofer to your factory car stereo system for a new sound experience.

• ADD SUBWOOFERS: Works with high power car stereos (up to 80 watts per channel) to add subwoofer bass systems to any car stereo.
• EASY TO INSTALL: Provides amplifier remote turn on output without removing car stereo.
• OUTPUT CONVERSION: Line out converter for car stereo speaker wire outputs to RCA Cable outputs.
• ADDITIONAL CHANNEL: Allows the addition of 2 or 4-channel amplifiers to factory or aftermarket stereos.
• BUY WITH CONFIDENCE: Backed by Scosche’s Lifetime Tech Support and Limited Lifetime Warranty.

User questions & answers

Question:	trying to install sound system (head unit, amp, subwoofers)to 2010 impala that has the stock Bose system. Will this be powerful enough to support that
Answer:	The secondary would be too short for the Kansbol to snap closed.
Question:	when they say 80 watts max per channel, are they refering to the output power of my factory radio? my amp puts out 125w x 4 RMS
Answer:	Please be advised that this pen has a twist mechanism.
Question:	Saab 2009 9-3 w stock radio, no Bose. looking to add a sub for bass. I will add an amp for this. Can i tap this units inputs from rear speaker
Answer:	No
Question:	Will this work woth 2006 chrysler croosfire
Answer:	Please be advised that every Waterman pen comes with one ink refill or cartridge.

Product description

General Features:

• User friendly Signal Delay enhances the acoustical alignment between the left and right channels plus the front and subwoofer channels
• Individual equalization controls for the front, rear and subwoofer channels for simple yet precise system tuning
• Six channels of active speaker level inputs  accepts up to 400 watts per channel
• AccuBASS  AudioControls patented pending processing to correct the bass roll-off in factory source units
• ACR-3 Dash Control Remote allows for control of the subwoofer level plus processing bypass which makes it ideal for demonstrations
• Internal Channel Summing  Easy interface with factory installed amplifiers with built-in crossovers
• GTOTM (Great Turn-On) Circuit  Powers up the DQ-61 when it detects signal on the main speaker level input
• Discrete Input and output level controls

• DQ-61 - AudioControl 6-Channel Factory Sound Processor with EQ and Signal Delay
• Designed to work with any factory stereo
• 6 speaker-level inputs (each can handle up to 400 watts RMS of power)
• Input level controls with maximization indicator LED
• Dimensions: 8-5/8"W x 1-1/4"H x 5"D

User questions & answers

Question:	How would i connect the inputs if i have aftermarket hu? rca to speaker wire? i wish this had rca inputs
Answer:	Through your HU speaker wires. But i would recommend you to get the Audio Control DQDX that has rca inputs only, which also has an additional crossover feature.
Question:	does this corm with the controller
Answer:	It should come with an ACR-3 Dash Control Remote http://www.audiocontrol.com/car-audio/factory-system-upgrade/dq-61/
Question:	How good this processor equalize the bass on the oem stereo
Answer:	The processor equalize the bass on a OEM Stereo very well. I have a solo baric 10 in my truck and it hits pretty hard
Question:	Is there a way to test the sound and change the settings with an app, if so which one
Answer:	No. This isn't designed to use Bluetooth or WiFi for making adjustments. It does 4 things. 1-line converter; 2-Separate EQ for front, rear & bass; 3-Bass volume correction (eliminates the compromise the factory makes) and 4-Time/phase alignment (front/rear and side to side). Look at the Audio Control DM-608 or DM-810 for Android, iOS or PC for complete digital control.

• HIGH PERFORMANCE CAR AUDIO AMPLIFIER | One of the best values you will find for a car amplifier for cars in the market! This 12v car amplifier features: 480W x 2 RMS @ 2 Ohm / 750W x 2 MAX, Freq: 15Hz~30KHz, <0.1% TDH, Built-In OEM Line Converter, Bass Boost 0~12dB, and Ground Loop Isolator. 12 volt output, This multi-channel amplifier for cars provides a real punch for your cars speakers or subwoofers!
• PRODUCES POWERFUL, CLEAN, FULL SOUND | Don't settle for weak sounding or underperforming car amplifiers. Your car audio system would not be complete without our multi-channel Massive amplifier. This car audio amplifier features: Built-in OEM line converters with RCA inputs that can take a high-level speaker signal at up to 9 Volts directly in. Full MOSFET with High Grade Switching Devices. Input Level 0.2-9.0v
• QUALITY TESTED AND GUARANTEED TO ALWAYS REACH ITS RATED POWER | Get more wattage and quality sound for less money! That is our guarantee! You don't need to set the gains to low to avoid distortion. These car amplifiers provides high power with low efficiency. Also, by sensing the DC offset of a factory radio it can activate the ATO (Auto Turn On) feature and Next Generation Advanced 5 Way Protection Circuitry.
• GREAT QUALITY PRODUCTS THAT WILL LAST LONGER | With 5-Way Advanced Protection and custom high-grade components your investment will last! With our extra features like Built-in Noise Reduction Circuitry, Auto Sensing Turn On Function, 12V Remote Output for External Devices (Hi-Level Inputs), and 4 Layers PCB design with SMD parts ensure you get your money's worth!
• MASSIVE AUDIO QUALITY GUARANTEED. Since 1999, Massive Audio has been an industry leader in high performance audio products. Massive Audio laid its roots in high quality audio reproduction through in-house engineering and a dedication to customers.

User questions & answers

Question:	How come it gets so hot
Answer:	The Molle multi sheath is made for the Mora Garberg, it will NOT fit the Mora Bushcraft Black.
Question:	Will this amp power a 12 inch punch p3 2 ohm 600 rms subwoofer
Answer:	Yes, you would remove the belt loop. You would not use the belt loop when using the multimount.
Question:	I have small space in my car how Inches the amp
Answer:	Hi this is a Garberg specific kit M-13000. You want the Kansbol Multi-mount kit seen at the link below. M-13002 https://amzn.to/31RdnsK
Question:	Does the massive logo glow blue like the Volt series
Answer:	It provides all the extra's you'd kit if you bought the Eldris Knife Kit. So yes it has the neck lanyard and the toggle strap to keep knife secured upside down and fire steel. Look at the Kit here: https://www.amazon.com/Morakniv-Fixed-Blade-Pocket-Sized-Stainless-Firestarter/dp/B01LYFRBKY/ref=sr_1_3?keywords=eldris+knife+kit&qid=1563389861&s=gateway&sr=8-3

Product features

Blade BP Series Multi Channel Amplifiers

Designed with our “Live, Loud and Play Hard” motto. Built-in OEM line converters with RCA inputs can take a high-level speaker signal at up to 9 Volts directly in. By sensing the DC off set of a factory radio it can activate the ATO (Auto Turn On) feature and convert the 12V turn on into a 12V switched out. Military grade PCBs, SMD parts, 5-way protection, full MOSFET high grade switching devices. BP Series amplifiers rule the road when it comes to features, performance and value.

Product description

JL Audio FiX-86 OEM Integration Digital Sound Processor w/ Automatic Time Correction and Digital Equalizer

• 24-bit DSP processor
• Quad 1/3 octave equalizers
• 8-ch. Inputs
• 4-ch. Stereo (Front & Rear) and 2 Subwoofer RCA Output Pairs
• Frequency Response: 20 - 20,000 Hz

User questions & answers

Question:	How is the power for this wired? Is it wired like an amp and connected to the battery, or through the fuse box? Does it also need grounded
Answer:	Cheap quality, yes. During someone's review on YouTube, the handle broke off while batoning some wood.
Question:	Hi do I need a crossover or a EQ whit this for better sound
Answer:	It is already attached to the belt loop portion of the sheath. It is ready to go.
Question:	can it be used with an aftrmarket radio
Answer:	The leather sheath most likely but not the plastic one.

Product description

An ACDelco GM Original Equipment Audio Amplifier is part of the audio system, and is a GM-recommended replacement for your vehicle’s original component. The purpose of the amplifier is to increase the power of a voltage or current signal. The output signal of an audio amplifier may consist of the same frequencies as the input signal or it may consist of only a portion of the frequencies, as in the case of a subwoofer or midrange speaker. The audio amplifier amplifies the signal and sends it to the appropriate speakers. Each of the audio output channel circuits (+ and ?) at the audio amplifier have a DC bias voltage that is approximately one half of the battery voltage. The audio being played on the system is produced by a varying AC voltage that is centered around the DC bias voltage on the same circuit. The AC voltage is what causes the speaker cone to move and produce sound. Both the DC bias voltage and the AC voltage signals are needed for the audio system to properly produce sound. These original equipment audio amplifiers have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

• Provide a wonderfully rich listening experience in your vehicle
• GM recommended replacement part for your GM vehicle’s original factory audio amplifier
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

User questions & answers

Question:	Is this refurbished
Answer:	This item is meant to reduce the signal strength from your aftermarket head unit before it goes into the stock amp, in this case, your Bose stock amp. If your intent is to continue using the Bose Amp to power your stock Bose speakers, this item does the job.
Question:	Does it fit a 2009 buick enclave
Answer:	Factory radio but even tho your radio says 125 x 4 that is a max rated not a RMS rating so you will be fine
Question:	Where is the amp located for a 2008 gmc denali xl
Answer:	Yes just make sure you get the polarity right
Question:	where is the delco radio amplifier on 2008 gmc acadia located
Answer:	It will work in any vehicle. What is more to the point is what application you have on mind.
Question:	Do this work on Mazda
Answer:	Excellent knife for camping.
Question:	I own a 2002 Yukon slt would it fit my truck
Answer:	Mine did not, and I've seen other reviews in the past where they say that it didn't come with it either. So if I where you I'd just expect it to not come with a the slingshot accessory.
Question:	will this fit in Buick Enclave
Answer:	Not gonna get full tang for htis price. It's $6. Be realistic. Pretty solid though. Better quality than I was hoping for $6.
Question:	can i use this part for my 2011 mazda 3 i already disconnected the old amp
Answer:	Step one: throw knife in garbage.Step two: buy better knife.
Question:	I have a 2010 gmc acadia with bose sound system on bord. can i use acdelco amplifier? my mechanic said that i need specifically the bose one? help
Answer:	Theres a very good possibility that it wont. The knife i ordered my sheath for was 5" & just barely fit. It was a thin bladed knife so it barely made it in. A slightly thicker one would not have at all.
Question:	Chevy Traverse and did not notice no Bose! Would this be what I need to update system to Bose? Current ones are horrible
Answer:	It was made in china I believe and is almost like a mini machete I've had it for about 2 months it will last a very long time as long as you take care of it! you can do many things with it so it is amazing and it's a very versatile investment and a worthy investment! It's high Quality! And last but not least you should get it!
Question:	will this item fit my 2010 chevy traverse lt with factory bose
Answer:	its junk, the handle broke on first use
Question:	Does it have to be flashed
Answer:	8.5 inches.

Product features

About Us

ACDelco is the premier supplier of GM Original Equipment (OE) automotive replacement parts, as well as a trusted provider of premium aftermarket parts for most other makes and models.

ACDelco provides high-quality parts for all major vehicle systems, as well as off-road, marine and industrial equipment. Our product portfolio includes maintenance parts such as car batteries, spark plugs, oil filters, air filters, wiper blades and brakes, as well as repair parts such as alternators, radiators, chassis and heating/cooling components.

Product description

An ACDelco GM Original Equipment Audio Amplifier is part of the audio system, and is a GM-recommended replacement for your vehicle’s original component. The purpose of the amplifier is to increase the power of a voltage or current signal. The output signal of an audio amplifier may consist of the same frequencies as the input signal or it may consist of only a portion of the frequencies, as in the case of a subwoofer or midrange speaker. The audio amplifier amplifies the signal and sends it to the appropriate speakers. Each of the audio output channel circuits (+ and ?) at the audio amplifier have a DC bias voltage that is approximately one half of the battery voltage. The audio being played on the system is produced by a varying AC voltage that is centered around the DC bias voltage on the same circuit. The AC voltage is what causes the speaker cone to move and produce sound. Both the DC bias voltage and the AC voltage signals are needed for the audio system to properly produce sound. These original equipment audio amplifiers have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

• Provide a wonderfully rich listening experience in your vehicle
• GM-recommended replacement part for your GM vehicle’s original factory audio amplifier
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

User questions & answers

Question:	Will this work with the non-Bose systems
Answer:	Never had an issue with temps. Possible if it gets hot, it’s not tuned correctly.
Question:	would this work well with 4 aftermarket speakers
Answer:	If your final impedance is 2 ohms we would suggest a " E2" Mono or "BP2000.1" Mono
Question:	Is there a warranty
Answer:	2"H x 7.1"W x 11.8"L
Question:	How many watts
Answer:	No

Product description

Wyze Cam V2 delivers fast, clear, live stream footage direct to your smartphone via the wyze app (iOS and Android), day or night. With motion and sound detection you can receive an alert anytime your wyze Cam V2 detects sound and motion, and view up to 14 days of saved alert videos for free - no monthly fees or subscription required. Use the wyze Cam v2’s new motion tagging feature to easily identify motion in both live stream and playback video modes. Plus, you can add an 8GB, 16GB or 32GB microSD card (sold separately) to enable continuous recording and schedule custom time lapse videos, and use 2-way audio to talk and listen through your wyze Cam V2. Use the wyze app to manage and view multiple cameras, share your cameras with other users, view alert videos, and record and share photos and videos directly from the app. The wyze Cam V2 must be powered to use (it does not have a battery), and is designed for indoor use (it is not weatherproof). Power Adapter Input - 110-240V (AC/DC). WiFi: 802.11 b/g/n 2.4GHz (Does not support 5GHz network) Supports WPA and WPA2 protocols

• 1080P Full HD live stream direct to your smartphone day or night with night vision (up to 30 feet away). works with 2. 4GHz Wi-Fi networks (does not support 5GHz Wi-Fi)
• Motion tagging technology detects and outlines motion in both live stream and playback video modes
• Wyze Cam automatically records a 12-second Event Video when it detects motion or sounds. Videos are securely uploaded to the AWS cloud via end-to-end encryption and are accessible for 14 days — no subscription or monthly fees required.
• Continuous recording with local storage - Wyze Cam supports local storage of recordings to a microSD card (sold separately). Play back videos with your Wyze app to solve life’s mysteries. Local Storage - Supports 8GB, 16GB and 32GB microSD cards in FAT32 format
• Magnetic base, 6-foot power cable and included adhesive metal plate let you mount your Wyze Cam anywhere - no screws required.Field of View:110° lens
• Works with Alexa and Google Assistant: ask your voice assistant to show your front door, kids room, or anywhere else you have your Wyze Cam
• Video - H.264 encoding. Day time video: 15 FPS. Night vision: 10 FPS. Night Vision - 4 IR LEDs (850nm) | Illuminates up to 29.6 feet (9 meters)

User questions & answers

Question:	does it work with google home hub or lenovo smart display
Answer:	Mines doesn't work with Google home hub
Question:	Do both of these cameras come with an SD card
Answer:	Memory Card it's not included, it's compatible with memory cards up to 32GB. I bought this > http://topreviews24.com/micro-sd-card/samsung-32gb-evo-select/
Question:	Will this work pointed out through a window or will it glare at night? Any suggestions to block the glare? One area only inside window is an option
Answer:	I have two of my cameras pointed through my windows. One in front and one in back of house. As long as there is lighting, it will not glare. When it is very dark, there is a glare. I put out 2 small solar lights in the backyard and turned off the night vision and absolutely no glare ever since. No glare issues in the front of the house as the neighborhood is well lit.
Question:	Has anyone used it for at least 6 months? Is it good to capture a thief in a home? What is its connectivity and alert system in case of a thief
Answer:	A lot of feedback here already, but I’ve had at least one Wyze camera in my home for about a year now and in my experience, they are better than my Ring devices in terms of connectivity and alerts. They connect in the app within 10-20 seconds and the Person Detection is great. I highly recommend the service which extends the recording time as it’s cheap but makes their devices that much more of a premium product. 10/10

Product description

Lanzar Model : HTG237

1000 Watt 2 Channel Mosfet Amplifier

2 x 125W RMS @ 4 OHMS

2 x 500W Max @ 4 OHMS

1 x 1000W Max @ 4 OHMS Bridged

2 x 225W RMS @ 2 OHMS

Electronic Crossover Network

Bass Boost Circuit

Bridgeable at 4 Ohms

2 Ohm Stereo Stable

Nickle RCA Inputs

Line Outs for Left and Right Channel

Low Pass Filter Controls

High Pass Filter Controls

Power and Protection LED Indicators

Soft Turn-on/Turn-off

THD: <0.01%.

S/N Ratio: >90dB

Channel Separation: >65dB

Freq. Response: 10Hz~45KHz

HPF Freq. Response: 80KHz

LPF Freq. Response: 50Hz-250Hz

Subwoofer Level Control

Fuse: 25A x 1

Dimensions: 9.84''(L) x 2.24''(H) x 8.81''(W)

• AUDIO EVOLUTION: This car speakers amp features regulated MOSFET Pulse Width Modulated that maintain rated power over a wide range of battery voltage. Excellent frequency response rates place these amps in a class of their own.
• SOUND SPECIALIZATION: This high-powered Power Amplifier is cutting edge technology at its finest. Nickel-plated RCA connectors and speaker screw-down terminals ensure a secure connection between amplifier and speakers that allow distortion-free sound.
• INTELLIGENT DESIGN: The car audio amplifier 2 channel safety features include power and protection LED indicators; soft turn-on/off; and thermal, overload, and speaker-short protection.
• RCA JACKS: The Line-Out jacks allow you to build multiple amplifier systems without having to use splitter cords to distribute the signal. This makes it easier to bring one set into the first amp, then use the line out jack as the feed to the next amp.
• POWER INPUT: The mosfet amplifier connections are for input power, chassis ground,& remote turn-on function. Use 8 gauge wiring for power & ground connections. The terminals will handle up to 4 gauge wiring with no negative effect or distortion of audio.

User questions & answers

Question:	Would this particular amp b ideal for 2 6.5s and 2 4x6s
Answer:	I highly doubt youll get 400w out of this amp let alone what it clams. I recommend an apcl15001d if you want real power for cheap. This isnt worth it
Question:	will this be good for 2 12 mtx termenior 400 rms
Answer:	Seperate your amps for better sound comtrol the four channel will run your coaxial speaker and run your tweeters then run a mono block single sub amp
Question:	Is this amp enough for 2 12 kicker cvr
Answer:	Yes, a direct replacement.
Question:	hi, i am looking an amplifier to conect 2 coaxials speakers, two tweeters and a subwoofer ¿how many channels should the amp have
Answer:	Most all of the USA Gibson Les Paul lineup.

Product description

Lanzar Model : HTG157

3000 Watt 2 Ohm Stable Mono Block Mosfet Amplifier

1 x 650W RMS @ 4 OHMS

1 x 1250W Peak @ 4OHMS

1 x 1500W RMS @ 2 OHMS

1 x 3000W Max @ 2 OHMS

Electronic Crossover Network

Bass Boost Circuit

2 Ohm Stable

Nickel RCA Inputs

Line Outs for Left and Right Channel

Low Pass Filter Controls

Power and Protection LED Indicators

Soft Turn-on/Turn-off

THD: <0.01%.

S/N Ratio: >90dB

Freq. Response:10Hz~45KHz

LPF Freq. Response: 50Hz-250Hz

HPF Freq Response:80HZ

Fuse: 40A x1

Dimensions:12.99''(L) x 2.24''(H) x 8.81''(W)

• AUDIO EVOLUTION: This amplifier car audio features excellent frequency response rates and crossover network that place these amps in a class of their own
• SOUND SPECIALIZATION: This high-powered Power Amplifier is cutting edge technology at its finest Nickel-plated RCA connectors and speaker screw-down terminals ensure a secure connection between amplifier and speakers that allow distortion-free sound
• INTELLIGENT DESIGN: The amplifier monoblock features include power and protection LED indicators; soft turn-on/off; and 1 channel amp design
• RCA JACKS: The Line-Out jacks allow you to build multiple amplifier systems without having to use splitter cords to distribute the signal This makes it easier to bring one set into the first amp, then use the line out jack as the feed to the next amp
• GREAT DEAL: Often a monoblock amp comes with a high price tag Yet the Lanzar mono amplifier is budget friendly with all the features, reducing crosstalk between channels

User questions & answers

Question:	Can I use this for my
Answer:	Yes, 2 fuse
Question:	Will this push 2 12" kicker comp r at 2 ohm
Answer:	Bought it a year ago and it sat in my closet. Never opened and went to install it. It didnt work. This is crap
Question:	do it have any fuse
Answer:	Yes
Question:	i have no sound.how do you get it to work
Answer:	….if the amp actually worked, yes. Sadly mine did not, nor did the replacement.

Product features

Lanzar Amplifier Car Audio, Amplifier Monoblock, 1 Channel, 3,000 Watt, 2 Ohm, MOSFET, RCA Input, Bass Boost, Mobile Audio

• 1 x 650W RMS @ 4 OHMS
• 1 x 1250W Peak @ 4OHMS
• 1 x 1500W RMS @ 2 OHMS
• 1 x 3000W Max @ 2 OHMS
• Electronic Crossover Network
• Bass Boost Circuit
• 2 Ohm Stable
• Nickel RCA Inputs
• Line Outs for Left and Right Channel
• Low Pass Filter Controls

• Power and Protection LED Indicators
• Soft Turn-on/Turn-off
• THD: <0.01%.
• S/N Ratio: >90dB
• Freq. Response:10Hz~45KHz
• LPF Freq. Response: 50Hz-250Hz
• HPF Freq Response:80HZ
• Fuse: 40A x1

Product description

Complete your car's sound system setup with the Hifonics ZG-3200.1D Zeus Gamma 2400W Max Class D Monoblock Amplifier. This class D amp delivers power efficiently and effectively to your subwoofers, speakers, and other output devices for crisp sound with minimal distortion and heat. Made for efficient power performance, this car audio amplifier is rated for 3200 watts x 1 channel at 1 ohm, 1600 watts x channel at 2 ohms, and 800 watts x channel at 4 ohms. This 1-channel monoblock amp uses Ultra-Fi MOSET output device technology and classic Hifonics aluminum construction for powerful sound, efficient cooling, and minimal distortion. All connections are secure with this car subwoofer amplifier. This amp features nickel-plated connectors and a molded connection terminal that's angled for easy access to all power, ground, and speaker connections. No matter your audio setup, pump up your sound with the Hifonics Zeus Gamma Mono Amplifier.

• CLASS D, MONOBLOCK AMP: Deliver powerful sound to your speakers and subwoofers with this class D, 3,200-watt, monoblock car audio amplifier
• PLENTY OF POWER: Does 3200 watts x 1 channel at 1 ohm, 1600 watts x channel at 2 ohms, and 800 watts x channel at 4 ohms
• MINIMAL DISTORTION: Maximum low voltage signal from the source unit comes into the amplifier circuit with minimal distortion
• SECURE CONNECTIONS: Nickel-plated, high-temperature, impact-resistant design with hex screw terminals that allow for secure connections
• EASILY TIE INTO YOUR SYSTEM: Easily tie into OEM audio systems that do not offer RCA output to maximize aftermarket amplifier power

User questions & answers

Question:	Will this amp be ok for 4 12” kicker comp vrs
Answer:	I think so..maybe 3 but not 4...but you be surprise it Will probably push all 4...amp is very powerful
Question:	How much rms
Answer:	It has 1600 rms
Question:	Any overheating issues
Answer:	I have not had any over heating issues with this amp..but i did have some with the brutus 600w amp
Question:	Will this amp be ok for 3 12s. kicker comprt
Answer:	Yes it definitely will