Product description

Switch selector volume control switch box hub distribution box for multi channel high powered amplifier control 6 pairs of speakers

• Up to 6 Separate Speaker Pairs to your Stereo System
• Accepts Speaker Wires Up to 14- Gauge
• Handles 100Watts Per Channel with Speaker Systems that have a Minimum Impedance of 8 Ohms
• Up to 6 Separate Speaker Pairs to your Stereo System - Support Two Stereo Amplifiers
• Accepts Speaker Wires Up to 14- Gauge - Frequency Response: 20Hz-20KHz
• Handles 100Watts Per Channel with Speaker Systems that have a Minimum Impedance of 8 Ohms - Dimensions: 16.92- Inches(W) x 3.03- Inches(H) x 6.29- Inches(D)
• Protection Circuitry Keeps it Running Smoothly
• Individual Speaker Volume Control

User questions & answers

Question:	can this replace my Pyle Pro PT
Answer:	No, not the devices have the same functions!
Question:	Ok, I bought the PT510 amplifier, and the PSPVC6 speaker selector, but not sure how to connect them together. Can anyone help
Answer:	Ok I'm going to try and keep it simple. Normally, once the amp is connected the 'sound' travels out of the red/white or left/right speaker connectors that are attached then to the speaker system. In your case, think of the speaker box as a 'conjunction' (like the words 'and/ but' in a sentence)..so just connect the 'speaker out' on your amp to the 'speaker in' on the speaker selector box...then connect the speaker box to the 6 speakers...be ready with a small flat head screw driver to open each the speaker connection ports...it's a bit more tedious but assures a professional non clip in/out connection...good luck...and make sure every thing is off to avoid 'blowing out' of the speakers and/or unit.
Question:	Does this have impedance protection - control against low ohms driving multiple speakers
Answer:	http://manuals.pyleusa.com/PDF/PSPVC4-6.pdf The last few pages of manual shows impedance of turning on combinations of speakers It is the amp that needs to be 4 ohm stable, I have a Denon AVR 3300 and AVR 2500. The more speakers active, the lower the impedance, (ohms Law) and the more power needed from the amp According to Crutchfield, we need a 4 ohm stable amp, and the Denon family provides overload protection, and the Denon amps have a 8 ohm (default) and a4 ohm setting I already fried an Onkyo amp, running all the speakers at once, for an extended period.
Question:	Is the Pyle PT510 240 Watt Amplifier a good receiver to use with this. I want to put sound in many rooms in my office
Answer:	I am by no means an AV expert. This amplifier was recommended to me by our AV guy in order to amplify the sound for distribution into several rooms in which we have speakers. We primarily use this amp in connection with an Apple TV device to play music from our iPhone or iPad in our kitchen, den, family room and outside speakers. Hope this response is helpful for you. Kind Regards, Robert

Product features

Premium New and Improved 6 Zone Channel Speaker Switch

Features:

• Multi-Channel High Powered Amplifier
• Up to 6 Separate Speaker Pairs to your Stereo System
• Accepts Speaker Wires Up to 14- Gauge
• Protection Circuitry Keeps it Running Smoothly
• Individual Speaker Volume Control
• Support Two Stereo Amplifiers
• Rugged & Durable Housing Construction, Cabinet Heatsink
• Control Powered 6 Channel Amplifier
• Plug and Play Easy Install

Technical Specs:

• Power Output: 6 x 100 Watts, Power Supply: 120/240V Voltage Selector
• Amplifier Design: 6-Channel, Minimum Impedance: 8 Ohms
• Frequency Response: 20Hz - 20KHz, Signal to Noise Ratio: >81dB
• Channel Separation: 80 dB, Crosstalk between Channels: 50 dB
• Speaker Terminal Wire Size: 14-22 gauge
• Max. Amplifier Input: 100W RMS, 150W AVG
• Max. Output per Speaker: 18W RMS, 50W AVG
• Product Dimension (L x W x H): 6.29'' x 16.92'' x 3.03'' -inches

Product description

PyleHome Model : PSS8

8-Ch. Stereo Speaker Selector

8 Channel High Power Stereo Speaker Selector

Up To 8 Separate Speakers Pair To Your Stereo System.

Accepts Speaker Wires Up To 14-Gauge.

Handles 100 Watts Per Channel With Speaker Systems That Have A Minimum Impedance Of 8 Ohms.

Protection Circuitry Keeps It Running Smoothly

Frequency Response: 20Hz-20KHz

Dimensions 12.8'' X 2.04'' X 6.12''

This speaker selector box allows you to play audio to up to eight different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch. Protection circuitry keeps it running smoothly and prevents speaker burn-out. Accepts speaker wires up to 14 gauge.

• THE NUMBER 1 SELLER 6 ZONE SPEAKER SELECTOR:The New and Improved Multi Zone Speaker Selector Can Play 8 Sets of Speaker at the Same Time or What Ever Speaker You Want to Control or a Pair of Speaker from High Powered Amplifiers.
• CONTROL YOUR POWERED 6 CHANNEL AMPLIFIER:You Can Control Any Amplifier from Pyle Crown Denon Sony Panasonic Yamaha and Many More.also Control 4 10 4 6 8 Inch Speaker Box.
• PLAY ANY COMBINATION SETS OF SPEAKERS AT ONCE.:The Pyle Speaker Switch Box Is Great Help For Controlling Ceiling Speakers Wall Speakers Home Theater Rooms Monitor Speaker Loud Speakers From All Sizes 4 6 8 12 Inch
• PLUG AND PLAY EASY INSTALL.The Pyle Speaker Distribution Hub Is Passively Powered By Your Stereo - Only Need To Plug In The Wires.Its A Good Idea To Add Labels On The Buttons For The Different Speakers So You Don't Have To Remember Each Zone Is
• WORRY-FREE SHOPPING: With the Pyle multi speaker switch we are confident of the quality of our product, therefore, we offer a 30 day money back guarantee no questions asked
• Up To 8 Separate Speakers Pair To Your Stereo System
• Accepts Speaker Wires Up To 14-Gauge

User questions & answers

Question:	Does this unit have impedance matching transformer feature
Answer:	Hi, yes the unit has an impedance matching transformer feature. You may check other details of the unit by visiting our website pyleaudio.com. Type the model number on the search box PSS8 for more details. Thank you.
Question:	I currently have.l a system set up with 16 gauge speaker wires. What would happen if I used the existing speaker wires in this device
Answer:	I think you will be fine, depending on how long your wire runs are.
Question:	Can you use it the opposite way....multiple recievers to one set of speakers
Answer:	No the only way you could do that is to biamp the reciever you could get a reciever with zone 2 or zone 3 and have different sound in different aera
Question:	How can it be both new and improved
Answer:	Increase connectivity range

Product features

Premium New and Improved 8 Zone Channel Speaker Switch Selector Switch Box Hub Distribution Box

This speaker selector box allows you to play audio to up to eight different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch. Protection circuitry keeps it running smoothly and prevents speaker burn-out. Accepts speaker wires up to 14 gauge.

THE NUMBER 1 SELLER 6 ZONE SPEAKER SELECTOR

The New and Improved Multi Zone Speaker Selector Can Play 8 Sets of Speaker at the Same Time or What Ever Speaker You Want to Control or a Pair of Speaker from High Powered Amplifiers.

PLAY ANY COMBINATION SETS OF SPEAKERS AT ONCE

The Pyle Speaker Switch Box Is Great Help For Controlling Ceiling Speakers Wall Speakers Home Theater Rooms Monitor Speaker Loud Speakers From All Sizes 4 6 8 12 Inch.

PLUG AND PLAY EASY INSTALL

The Pyle Speaker Distribution Hub Is Passively Powered By Your Stereo - Only Need To Plug In The Wires.Its A Good Idea To Add Labels On The Buttons For The Different Speakers So You Don't Have To Remember Each Zone Is.

Product description

PyleHome Model : PSS6

6-Ch. Stereo Speaker Selector

6 Channel High Power Stereo Speaker Selector

• Up to 6 Separate Speaker Pairs to Your Stereo System
• Accepts Speaker Wires up to 14-Gauge
• Handles 100Watts per Channel w/ Speaker Systems That Have Minimun Impedance of 8 Ohms
• Protection Circuitry Keeps It Running Smoothly
• Frequency Response: 20Hz-20KHz
• Dimensions: 9.05''(W) x 1.85''(H) x 5.90''(D)

This speaker selector box allows you to play audio to up to six different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch. Protection circuitry keeps it running smoothly and prevents speaker burn-out. Accepts speaker wires up to 14 gauge.

• THE NUMBER 1 SELLER 6 ZONE SPEAKER SELECTOR:The New and Improved Multi Zone Speaker Selector Can Play 6 Sets of Speaker at the Same Time or What Ever Speaker You Want to Control or a Pair of Speaker from High Powered Amplifiers.
• CONTROL YOUR POWERED 6 CHANNEL AMPLIFIER:You Can Control Any Amplifier from Pyle Crown Denon Sony Panasonic Yamaha and Many More.also Control 4 10 4 6 8 Inch Speaker Box.
• PLAY ANY COMBINATION SETS OF SPEAKERS AT ONCE.:The Pyle speaker switch box Is great help for controlling ceiling speakers Wall Speakers home theater rooms monitor speaker loud speakers from all sizes 4 6 8 12 inch
• PLUG AND PLAY EASY INSTALL.The Pyle speaker distribution hub Is passively powered by your stereo - only need to plug in the wires.Its a good idea to add labels on the buttons for the different speakers so you don't have to remember each zone is
• WORRY-FREE SHOPPING: With the Pyle multi speaker switch we are confident of the quality of our product, therefore, we offer a 30 day money back guarantee no questions asked

User questions & answers

Question:	I am installing in-wall speakers in multiple rooms. My question is what is the best cheapest in-wall volume controller that would work with this speaker selector
Answer:	There is no difference in for the install if you mount speakers in the wall or ceiling.
Question:	Several questions, How do you hook it to your stereo, I am hard of hearing so I hooked 3speakers to my stereo system,this is hooked to my tv when I turn it up some times it turns off by it self I do not understand that I would like more speakers all the 5 star reviews makes this product sound real good. the receiver
Answer:	I think so. They mount with a screw and clamp. The screw is accessible behind the removable front grill. The speaker comes with a template so you know what size to cut out in the wall or ceiling. After you insert the speaker into the recess, as you turn the screw, it tightens the clamp onto drywall, securing it in place. Although it is designed for drywall, I think it will work on anything with approximately the same thickness (~3/4 inch thick).
Question:	How Do You Hook A PSS6 Speaker Selector To A Pyle PCAU46A
Answer:	I would recommend a 5.1 home audio receiver.
Question:	can i play all 6 speakers at the same time
Answer:	The pyle pta44bt would be a good amp for the speakers.

Product features

Premium New and Improved 6 Zone Channel Speaker Switch Selector Switch Box Hub Distribution Box

This speaker selector box allows you to play audio to up to six different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch. Protection circuitry keeps it running smoothly and prevents speaker burn-out. Accepts speaker wires up to 14 gauge.

Product description

The TC-7214 is an audiophile grade, high power 4 zone speaker selector switch which utilizes top quality internal circuitry, gold plated luxury input/output jacks which can accommodate up to 4mm banana sockets, UL, VDE approved silver plated brass contact switches to ensure best power transfer while not compromising your sound quality like all the low cost speaker switches online. It can handle 200W RMS while providing selection of up to four pairs of speakers from one location. Each zone may be selected individually, simultaneously or in any combination. It provides a perfect solution to the need for high quality distributed audio in residential audio or commercial sound applications. Internal switching uses a combination of series and parallel wiring, ensuring that the connected amplifier sees a minimum of a 4 ohm load when up to four pairs of 8 ohm speakers are connected. This means that any conventional amplifier or stereo receiver can drive multiple sets of speakers, without the need for external impedance matching devices. Includes pre-printed and blank room labels to mark speaker location. Strong stylish metal enclosure.

• Audiophile grade circuitry, UL, VDE approved silver plated brass contact switches for optimal sound transfer
• IN/OUTPUT through luxury gold plated banana sockets which can accomodate up to 4mm plugs or wires
• 200W RMS power handling, suitable for 8 ohm and above speakers
• Includes pre-printed and blank room labels to mark speaker locations
• Dimensions: 10.5" L x 5.3" W (includes banana sockets) x 2" H

User questions & answers

Question:	I don’t see a protection button. Is protection built into the circuitry and just auto running all the time
Answer:	Impedance matching circuitry is built and activates according to the amount of speakers selected.
Question:	watts peak or 200 watts standard RMS
Answer:	they never are clear about that. always stating 200 watts rms. My take: I'm running 80 watts min. per channel @ 8ohms using 3 pairs speakers rated 8ohms that handle 130 watts each, no problems. this switch uses internal wiring configurations NO ON-OFF switch just speaker in or out select. REQUIRES 8 Ohm SPEAKERS TO WORK PROPERLY
Question:	Does this connect to the speaker ouput of my amplifier
Answer:	Yes. Speaker outputs from your amp to amp inputs on swith, then from speaker outputs on switch to your speakers.
Question:	Can you use this product with speakers that are 4 ohms or 6 ohms
Answer:	8 ohms minimum.

Product description

The SP-71 is a 2 way loudspeaker source control designed to accept two stereo audio sources such as two receivers or amplifiers to share use of one pair of loudspeakers though the individual L and R, Amp A and B switch.

• Use two amplifiers / receivers with one pair of speakers
• In/Out through high quality gold plated heavy duty banana jacks that can accept up to 12 gauge wire
• Channel L and R switched individually
• Protection circuit design safeguards your amplifier and speakers
• Power rating: 100W RMS, 200W PEAK per channel

User questions & answers

Question:	Has anyone noticed a drop in sound quality or power level
Answer:	No
Question:	Can i use this to switch between two preamps going into one amp
Answer:	I think with honey being as thick as it is, would likely be far slower thank transferring it manually. Even for pumping out engine oil is a slow process.
Question:	Does anyone know of a "smart" (i.e. controllable with Google, etc) switch like this
Answer:	If it’s dirty oil or otherwise why clean it?
Question:	Is the selector switch a “ Break before make” Type of switch? I want to ensure that it is virtually impossible to back feed one amp into the other
Answer:	I have no clue on that.

Product description

Premium New and Improved 4 Zone Channel Speaker Switch Selector Switch Box Hub Distribution Box for Multi Channel High Powered Stereo Amplifier A/B/C/D Switches 4 Pairs Of speakers - Pyle (PSS4) Product description (optional) : PyleHome Model : PSS44-Ch. Stereo Speaker Selector4 Channel High Power Stereo Speaker Selector Up to 4 Separate Speaker Pairs to Your Stereo System Accepts Speaker Wires up to 14-Gauge Handles 100Watts per Channel w/ Speaker Systems That Have Minimun Impedance of 8 Ohms Protection Circuitry Keeps It Running Smoothly Frequency Response: 20Hz-20KHz Dimensions: 7.48''(W) x 1.97''(H) x 4.72''(D) This speaker selector box allows you to play audio to up to four different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch. Protection circuitry keeps it running smoothly and prevents speaker burn-out. Accepts speaker wires up to 14 gauge.

• THE NUMBER 1 SELLER 4 ZONE SPEAKER SELECTOR:The New and Improved Multi Zone Speaker Selector Can Play 4 Sets of Speaker at the Same Time or What Ever Speaker You Want to Control or a Pair of Speaker from High Powered Amplifiers
• CONTROL YOUR POWERED 4 CHANNEL AMPLIFIER:You Can Control Any Amplifier from Pyle Crown Denon Sony Panasonic Yamaha and Many More.also Control 4 10 4 6 8 Inch Speaker Box
• PLAY ANY COMBINATION SETS OF SPEAKERS AT ONCE.:The Pyle speaker switch box Is great help for controlling ceiling speakers Wall Speakers home theater rooms monitor speaker loud speakers from all sizes 4 6 8 12 inch
• PLUG AND PLAY EASY INSTALL.The Pyle speaker distribution hub Is passively powered by your stereo - only need to plug in the wires.Its a good idea to add labels on the buttons for the different speakers so you don't have to remember each zone is
• WORRY-FREE SHOPPING: With the Pyle multi speaker switch we are confident of the quality of our product, therefore, we offer a 30 day money back guarantee no questions asked

User questions & answers

Question:	I want to use this on two sets of speakers, one set for front height & second set for side surrounds and switch between the two. Is it possible
Answer:	I have speakers throughout my house. The Pyle Six-zone box allows me to have music in most every room. Hook each speaker you have to the Pyle and hook the Pyle to your receiver, speaker A or B. I have mine on B. Connect your receiver audio to your TV audio. There is a separate button on the Pyle that you should always keep positioned to on (button in). That is the easiest I can make it for you. This box works perfect for me and has never shut off. Good luck to you.
Question:	Does this switch allow me to control sets of speakers independently
Answer:	I am running an older Technics amp 2x100 6 pairs of speakers at times so I would say yes. Just remember you are putting this amp to a lot of work if you're running 6 pairs of speakers so watch the temps on the amp.
Question:	One person indicated what they believed the protection button was. Does anybody know? Pyle technical support apparently doesn't exist
Answer:	Maybe. The more speakers that you connect the lower their effective impedance as seen by the amplifier. And the lower the effective impedance the higher the current that the amplifier must generate in order to drive the speakers to a specific listening level without distortion.Most speakers, particularly the less costly ones, have a nominal 8 ohm impedance. So if you are driving one set of such speakers the amplifier will be seeing an 8 ohm load. But if your amplifier is driving 2 sets of such speakers the amplifier will be seeing 1/(1/8 + 1/8) = a 4 ohm load; if your amplifier is driving 3 sets of such speakers the amplifier will be seeing a 1/(1/8 + 1/8 + 1/8) = 2.7 ohm load, etc. With 6 speakers your amplifier will be seeing a 1.3 ohm load. And this would be a nominal and typically maximum load; in practice the load fluctuates depending on frequency and is effectively lower for short periods of time.Some amplifiers are designed to drive such low loads but many are not. If you try to do that with such a low current amplifier for a long period of time you will burn up the amplifier. That is why speaker selectors like this one have a protection button which basically adds a resistance in series with the speakers in order to increase the impedance seen by the amplifier. This will reduce the overall efficiency and you will notice that you have to increase the volume to get the same amount of sound as with the protection button off.So, if your amplifier has a sufficient current capability to drive those 6 speakers to your desired listening levels, great. If it doesn't, and if the listening level is too low for your tastes with the protection button on, you will need to either settle for lower volume or get a more powerful amplifier.
Question:	How do I hook this up to my 5.1 receiver
Answer:	The sound is great there is no distortion.

Product features

Premium New and Improved 4 Zone Channel Speaker Switch Selector Switch Box Hub Distribution Box

This speaker selector box allows you to play audio to up to eight different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch. Protection circuitry keeps it running smoothly and prevents speaker burn-out. Accepts speaker wires up to 14 gauge.

Product description

1.4-Channel stereo speaker control, allow conventional amplifier or stereo receiver to drive multiple sets of speakers, without the need for external impedance matching devices



2.Ideal for low cost distributed audio in residential or commercial sound applications



3.Just hooked up to the stereo.No extra power supply needed



4.Individual control of each speaker pair. Impedance constant at 4-8 Ohms, 100WRMS, 200W max



5.Speakers connected must be no less than 8 ohms

• 4-Channel stereo speaker control, allow conventional amplifier or stereo receiver to drive multiple sets of speakers, without the need for external impedance matching devices
• Ideal for low cost distributed audio in residential or commercial sound applications
• Just hooked up to the stereo.No extra power supply needed
• Individual control of each speaker pair. Impedance constant at 4-8 Ohms, 100WRMS, 200W max
• Speakers connected must be no less than 8 ohms

User questions & answers

Question:	does anyone know the demensions of this width, depth and high
Answer:	It's demensions is 175x114x49(mm). Hope it can help you.
Question:	Does the volume decrease significantly for each speaker when using this vs. attaching directly to the amplifier
Answer:	I use 2 sets of speakers with good volume if use all 4 sets it does decrease. Consider 25% each set.
Question:	I lost the instructions. Where can I get a copy
Answer:	This is a straight forward box, it has one stereo (R , L ) input and four stereo outputs, depending on which output switch you select (ON). The Input signal to this box should be coming from the amplifier speakers out, and the output of the box ( 1 ~4 ) should be connected to the 1~ 4 speakers under test(s). Hope this help
Question:	HImy speakers have a nominal impedance of 4-6 ohms will this work for me
Answer:	If your amp can drive 2 ohms speaker sets, then yes. In this 4-set selector, spkrs 1-2 will parallel, spkrs 3-4 will parallel, and the 2 subsets will series. So if using 4 ohm spkrs, then 1-2 will become 2 ohm, 3-4 will become 2 ohm, and all spks will series back to 4 ohm.

Product description

The SSVC-4. 1 Speaker Selector is a resistor-based, impedance matching speaker selector used for connecting up to four pairs of 4-ohm or 8-ohm speakers, while maintaining a safe impedance load for your amplifier or receiver. Each pair of speakers can be independently turned on or off using push buttons on the front panel, with no need for worrying about amplifier loading. Each zone features an independent volume control.

• Connect and safely control multiple speaker pairs with a single amplifier. Automatic impedance protection circuitry.
• 100 watts/channel continuous power handling capacity, 200 watts/channel peak. 5-ohm minimum amplifier impedance with four 4-ohm speakers selected, 6-ohm minimum with 8-ohm speakers.
• Individual zone on/off buttons and volume controls.
• Heavy-duty screw-type connectors supporting 12-18 AWG speaker wire.
• Isolated left/right circuit grounds provide safe connection for amplifiers with floating grounds or bridged configurations. Accurate, noise-free switching.

User questions & answers

Question:	Input from sony str-dh190 and out to 3 zones but no audio; tried connecting 1 zone and still no audio - tried 6 & 8 ohms - any other recommendations
Answer:	Make sure the input volume is up (Bluetooth, aux from phone or aux) amp volume should be up at least 50%-75%. Then turn up the SS4 vc. Should be on 8ohm, button pressed in (in the on position) and select A or B depending on what you have it plugged into the back.
Question:	Is there a warranty
Answer:	Yes it comes with an one year warranty.
Question:	Monoprice, can I connect 1 pair of rated 8 ohm (nominal 6 ohms - Elacs speakers and a different pair of 8 ohm speakers to play simultaneously
Answer:	Yes, that is the whole point of this product - to allow one amplifier to drive several pairs of speakers, with independent volume control over each pair, and impedance protection to protect the amplifier.
Question:	What does l- l+ r- r+ mean
Answer:	L is for the left speaker and R is for the right speaker.

• ZONE CONTROL: This high power speaker selector is an effective way to distribute music to eight listening zones and includes individual on/off selectors for each zone and is constructed of 14-gauge steel.
• DESIGN: The ISS8 is a single source speaker distribution system with individual on/off selectors for each listening zone which distribute one stereo speaker-level signal from your amplifier across 8 zones.
• CONNECT: The phoenix connectors on the ISS8 are easily removable to avoid frustration when connecting multiple speakers. With screw-down terminals, the speaker wire cable will never come loose.
• IMPEDANCE PROTECTION: Impedance-matching frequency protection circuitry allows one amplifier to safely power multiple pairs of speakers without your amp or receiver overheating or damaging to the equipment.
• EASY INSTALLATION: The low profile ISS8 is constructed of heavy-duty steel and allows easy access to the protection switch. The black brushed aluminum design easily fits into a cabinet or anywhere in the home.

User questions & answers

Question:	My Yamaha Receiver (750) has A and B speaker outputs. Would I connect the ISS4 inputs to the B outputs and then run 4 separate speaker pairs from the B side of the receiver leaving the A side for the main listening room speakers
Answer:	It really depends on the type of speaker configuration you have in your main zone. If you have a 5.1 environment in your main zone the best option is to connect the iss4's inputs to the zone 2 terminal on the back of your 750. This will allow you to listen to different sources in each zone at the same time. For instance you could watch a DVD in your main zone and in zone 2 you could be listening to an iPod or the fm tuner. Hope this answers your question, if you choose this option then remember you can only listen to analog sources in a zone 2 setup.
Question:	I can see how to select zones, how do you select the source? I have a phono amp and home theater amp I need to switch between, one set of speakers
Answer:	There is an round A/B button next to each rectangular zone button. Undepressed your are selecting source A. Press the button in and you are now selecting source B.
Question:	Can I run the 6 pairs of speakers at the same time? If this can be done, the volume drops
Answer:	Of course the volume drops. You will have 6 parallel circuits, each getting 1/6 the current. Basic rules of electricity.
Question:	I've bought this and I have connected it to 4 zones of in-wall speakers but the volume is extremely low! Do I need a receiver before the input
Answer:	What are you powering the speakers with?? In an ideal setup this device would be connected after the stereo amplifier or a/v receiver. It's is recommended to have an power source of at least 50W per channel supplying power to this volume selector. If you have impedance matching volume controls make sure the protection circuit button is in the off position(pushed out). If you have no volume controls push the circuit protection button in so that it equalizes the impedance.

Product features

Dual Source

The dual source allows you to have 2 different music sources connected, with some units offering the ability to select source per zone.

Volume Control

Using the same technology as our in-wall volume controls, most units offer volume control per zone.

Impedance Protection

Impedance protection allows a single amplifier to safely power several pairs of speakers without going below the amp’s impedance rating.

Easy to Install

Removable input/output phoenix connectors accept up to 14g wire and provide hassle-free hook-up.

OSD Audio 8-Zone Single Source Speaker Selector

The ISS8 high power speaker selector is an easy and effective way to distribute music to up to eight listening zones (eight pairs of speakers) and play any pair, a combination of pairs, or all pairs simultaneously. East to connect with a low-profile design that easily fits into a cabinet or equipment rack.

Product description

Pyle Model : PSLSW4

4-Ch. Speaker Selector System

Multi-Zone Speaker Selector, 4-Channel Audio Speaker Receiver System

Features:

Convenient Audio Control for Up to 4 Pairs of Speakers

Home Theater Stereo Amplifier System Support

Independent Audio Source Channel Volume Controls

Input/Output: Screw Type Connector Terminals

Compact Desktop / Tabletop Receiver Design

Front Panel Button Control Center

Master Power Switch

Built-in Electronic Overload Protection Circuitry

Technical Specs:

Power Handling: 100 Watt MAX Per Audio/Speaker Channel

Speaker Selector Type: 4-Channel

Speaker Cable Wire Support: Up to 14-Gauge (14 AWG)

Minimum Impedance: <8 Ohm

Frequency Response: 20Hz-20kHz

Dimensions (L x W x D): 16.9'' x 6.3’’ x 3.0'' -inches

• 100 WATT MAX: The Pyle Multi-Zone A B Speaker Selector Switch is perfect for your home theater sound system w/ 100W max power per channel. For use w/ 8ohm impedance speakers. Has a compact slim tabletop design that complements any home theater setup
• CONTROL 4 SPEAKERS: The new indoor multichannel speaker switcher controls up to 4 speaker pairs connected to a stereo amplifier at the same time or in combination. Input/output via screw type connector terminals which accept up to 14AWG speaker wire
• INDEPENDENT AUDIO CONTROL: Features independent audio source channel volume controls. The push button design lets you activate each pair individually to customize the listening experience in your home and independently control the volume to each pair
• EASY SETUP: Simply connect the left and right outputs from your amp/receiver and/or another source to the left and right A/B inputs on the mini 4-channel multizone controller, connect up to 4 pairs/8 speakers and enjoy high quality audio performance
• OVERLOAD PROTECTION: Equipped w/ front panel control switches consisting of rotary knobs for volume control and a master speaker switch. Offering high-quality audio, it also provides overload safety protection circuitry and long-term reliability

User questions & answers

Question:	Will fit on slider rack shelf with 16 inches wide and 15 inches deep? thank you
Answer:	Good question. There are two things you should know before you pull the trigger on this. Banana plugs don’t insert far enough to stay put, and since I have this box hooked up to amplified speakers I kept getting a buzz. I bought special banana plug pig tails which I ended up removing because of said problem. What did work very well for me was to remove the banana plugs and strip and solder the speaker wires then tighten the threaded part against the inserted wire in the hole on the shaft, a very tight connection and that worked great. The other issue is you can’t turn off one the speakers which was reported in one of the comments. It is annoying but for my application one set of speakers is downstairs with their own volume control so, I just adjust the volume on them when in use. Hope this helps.
Question:	I don't understand the description. what does the a /b button at each speaker volume control mean? doesn't the speaker pairs selected play together
Answer:	Hi, I have one of these (returning the 1st one due to poor speaker terminal , I find that it will accept a 4mm and thicker Banana Plug. Amazon's model was poor fit, but MediaBridge's plug in more securely. I have not fully connected my XtremePro yet, but I hope this helps.
Question:	Can the speaker connectors take banana plugs as opposed to threading the wires
Answer:	I may not be understanding your question correctly, but with this item I am using the volume control on my amp for the front speakers and the volume on this device to control the volume on the rear speakers. So yes, I can set one set of speakers at a different volume that the other. Again, if I am understanding your question correctly.
Question:	So I can hook up 4 sets of speakers on my new Pyle unit all on one receiver without worry of damage? Looked like chart had impedence fall off to
Answer:	Yes as far as I can tell. Aka-when I only have on speaker on and flip the switch to turn another group on, the volume drops. It’s not necessarily half the volume though.

Product features

4-Ch. Speaker Selector System

This speaker selector box allows you to play audio to up to four different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch and an independent volume control. You can also hook up another amplifier. Protection circuitry keeps it running smoothly.

CONTROL 4 SPEAKERS

The new indoor multichannel speaker switcher controls up to 4 speaker pairs connected to a stereo amplifier at the same time or in combination. Input/output via screw type connector terminals which accept up to 14AWG speaker wire

INDEPENDENT AUDIO CONTROL

Features independent audio source channel volume controls. The push button design lets you activate each pair individually to customize the listening experience in your home and independently control the volume to each pair. Distribute your music to every room in your home with this 4 Channel Speaker Selector from Pyle.

EASY SETUP

Simply connect the left and right outputs from your amp/receiver and/or another source to the left and right A/B inputs on the mini 4-channel multizone controller, connect up to 4 pairs/8 speakers and enjoy high quality audio performance

Protection

Equipped w/ front panel control switches consisting of rotary knobs for volume control and a master speaker switch. Offering high-quality audio, it also provides overload safety protection circuitry and long-term reliability.

Watt

The Pyle Multi-Zone A B Speaker Selector Switch is perfect for your home theater sound system w/ 100W max power per channel. For use w/ 8ohm impedance speakers. Has a compact slim tabletop design that complements any home theater setup

Dimensions

The Pyle Multi-Zone A B Speaker Selector Switch has a (L x W x D): 16.9'' x 6.3’’ x 3.0'' dimensions.

• FEATURE: This Emergency Warning Horn siren PA system includes a control box, a wired hand-held microphone and a heavy-duty speaker.
• ADVANTAGE: With an adequate power output of 200W and powerful speakers, with a higher rating of 121-130dB you get quality audio output which is audible from a distance away.
• MULTI FUNCTION: Multiple operation options which include horn and siren , with the siren option giving you yelp, wail, hi-lo and hi-lo and also manual horn & manual siren.
• ADDITIONAL AUXILIARY SWITCHES: The warning system offers two 20A switches which you can use to power other external devices and appliances, such as Strobe Lights.
• APPLICATION: It contains 8 warning tones to fit for police, ambulance, fire, engineer, private vehicles, etc.

User questions & answers

Question:	Can the siren portion be disabled so anyone using my vehicle can't use it? I would like to be able to reconnect it in the future
Answer:	disconnect the main power wherever you spliced in.
Question:	Can this siren fit a 2006 ford mustang police interceptor
Answer:	It's universal so it will fit anything. You have to find a place to mount the horn speaker and figure out where the main unit fits. You will need extra wiring to wire up the speaker and power/fuse connections.
Question:	Will this come with instructions to wire it all including the aux
Answer:	Quick install just power and ground
Question:	Esta sirena suena duro
Answer:	Yes

Product description

PyleHome Model : PVCS2In-Wall / Wall Plate Speaker SelectorIn-Wall Speaker Selector Switch, Wall Plate Speaker Control Features: Convenient Speaker SelectionSimple Push Button Operation Possible Configurations: A, B, or Both (A + B)Terminal Block Speaker ConnectorsUniversal Standard Wall Plate SizeFits Standard Electrical Junction / Gang BoxesCompatible with All Audio / Video SystemsIncludes Decorative Frame Plate Cover120 Watt Load Power HandlingThe Pyle PVCS2 is an in-wall A/B speaker selector switch that installs in a junction box, just like a light switch. This switch makes it simple to direct your home amplifier's audio to two sets of speakers, such as one set indoors and one set outdoors. Activate the A speakers, B speakers, or both. Easy push button operation allows you to activate or deactivate your speakers quickly. The included wall plate frame cover allows for a clean installation for your walls. Take control of the audio with the Pyle PVCS2 Wall Plate Speaker Control Selector Switch.

From the Manufacturer

• EASY TO INSTALL: The Pyle in-wall A/B speaker selector switch installs in a junction box, just like a light switch. Fits standard electrical junction/gang boxes. Makes it simple and easy to direct your home amplifier audio to 2 sets of speakers
• PUSH BUTTON OPERATION: The smart indoor outdoor speaker control features a convenient and simple push button selection which makes operation a breeze! Activating or deactivating the A speakers, B speakers, is as easy as a push of a button
• CONFIGURATIONS: Featuring three configurations to choose from: select A speakers, B speakers, or both A and B (A+B) speakers. The easy push button operation allows you to activate or deactivate your preferred set of speakers quickly
• UNIVERSAL COMPATIBILITY: The 2-channel speaker controller is compatible w/ all audio and video systems making it a wise choice to add to your home theater system. Also features up to 120 watt power load handling and terminal block speaker connectors
• STANDARD SIZE: It features a universal standard wall plate size. The included decora-style wall plate frame cover means this switch will unobtrusively blend into your wall and allows for a clean installation on your walls
• Connector type: usb

Product features

In-Wall Speaker Selector Switch

The Pyle in-wall A/B speaker selector switch installs in a junction box, just like a light switch. Fits standard electrical junction/gang boxes. The easy push button operation allows you to activate or deactivate your preferred set of speakers quickly.

PUSH BUTTON OPERATION

The smart indoor outdoor speaker control features a convenient and simple push button selection which makes operation a breeze! Activating or deactivating the A speakers, B speakers, is as easy as a push of a button

EASY TO INSTALL

A/B speaker selector switch installs in a junction box, just like a light switch. Fits standard electrical junction/gang boxes. Makes it simple and easy to direct your home amplifier audio to 2 sets of speakers

CONFIGURATIONS

Featuring three configurations to choose from: select A speakers, B speakers, or both A and B (A+B) speakers. The easy push button operation allows you to activate or deactivate your preferred set of speakers quickly

UNIVERSAL COMPATIBILITY

The 2-channel speaker controller is compatible w/ all audio and video systems making it a wise choice to add to your home theater system. Also features up to 120 watt power load handling and terminal block speaker connectors

Product description

BRAND NEW, Model TCC TC8, 1x2 Stereo Speaker Selector Switch Box... Allows hook up of 2 pairs of speakers to one speaker output. Rugged rocker switches with push type speaker terminal jacks mounted in a shielded metal box. Individual control of each speaker pair. Impedance constant at 4-8 Ohms, 100WRMS, 200W max. Accepts up to 14 Gauge speaker wire. Speaker pairs may be selected one at a time or simultaneously.

• Allows hook up of 2 pairs of speakers to one speaker output.
• Rugged rocker switches with push type speaker terminal jacks mounted in a shielded metal box.
• Individual control of each speaker pair. Impedance constant at 4-8 Ohms, 100WRMS, 200W max.
• Accepts up to 14 Gauge speaker wire. Speaker pairs may be selected one at a time or simultaneously.
• Speakers connected must be no less than 8 ohms.

User questions & answers

Question:	could you theoretically wire this backwards with two different receivers outputting to a single set of speakers
Answer:	You could be would not recommend as if you mistakenly engage both amps at the same time you will end up damaging your system. For your application would recommend the following item specifically designed for safely controlling a pair of speakers from two different amp / receivers. https://www.amazon.com/gp/product/B0796KGVXT
Question:	What are the dimensions, width x depth x height
Answer:	4x7Front height 1in back about 2in
Question:	Can i hook up 2 pairs of 4ohm jbl provspeakers without putting significant strain on extron mini amp? it is rated 4ohm load min
Answer:	Specs say impedance rating is 4-8 ohms. You are fine.
Question:	I have 1 center channel ouput, will it work to go from 1 channel to 2 channels
Answer:	It does exactly what the diagram shows … taking a L(+ and -) & R (+ and -) as input and sends it to 1 or 2 destinations. So you have 4 connectors INPUT and TWO SEPARATE OUTPUTS (4 commectors EACH). If you only want to send the CENTER channel to TWO OUTPUT CHANNELS … I never used it for this but 'presumably' connect to INPUT (L + and -) and connect OUTPUTS will be at (L+ and -) of EACH OUTPUT CHANNEL???.

Product description

Features:



4-IN 4-OUT (switch audio sources input)



Switch different input or output conveniently



No need power supply, plug and play directly



Circuit design does not affect sound quality



Made of FR4 PCB circuit board



Mini size compact audio splitter for home audio







Applications:



Connect sockets are AUX 1/8" (3.5mm)



Input connections: Computer / Phone / Music player. etc.



Output connections: Active speaker / Headphone amp / Power Amplifier. etc.







Use instruction:



Left knob on top: for switch/select input signal way



Right knob on top: for switch/select output signal way

• 3.5mm AUX Stereo Audio Switcher
• 4 ways input, 4 outputs / 4 IN 4 OUT
• Compact size Audio Signal Switch box
• Select knob on top, Switch input or output easily
• No need power supply, plug and play directly

User questions & answers

Question:	What specifically causes the static issue when two inputs are connected (like what the comments below mention
Answer:	Hello, im no expert but i do speak from experience. So I used this on a custom speaker build and had no issues, HOWEVER i do use ground loop isolator and inline ferit rings to avoid/clean up sound abit. Because that static or (noise) is cause by the power or current that amps or in this case the switch board picks up, and can come from any where its connected to, PC, amplifier, nearby power source you name it. Hope this helps!
Question:	Are the audio plugs 4-pole? (stereo and microphone
Answer:	No. The inputs and outputs are all 3.5mm stereo.
Question:	Can the input in channel 1 be heard at the same time in both four outputs (having connected 4 headphones)? thanks
Answer:	Unfortunately no, this is more of a single lane chooser if you will. It has 4 imputs and 4 out puts, youre just choosing single wich imput comes out of what single out put.
Question:	Does this support 4 pole? Specifically can a headset with a mic be plugged in to an output and transmit to an input computer
Answer:	I am fairly but not absolutely certain the answer is no. I don't particularly want to disassemble mine to check for sure but it's open construction gives some visibility into how many solder connections there are to the input and output jacks. Between that and what people say about it comments, and the product description -- pretty sure, no. That could be a nice product, though.