Product description

Spread your music everywhere. One of the most popular trends in home audio is whole house audio distribution. Unfortunately True multi-zone distribution systems are normally built into only the higher end receivers or require an expensive audio distribution network. Monoprice brings everything within reach of the average homeowner by offering a wide selection of home audio distribution accessories. A key element of any home audio distribution system is a speaker selector. The speaker selector allows you-inch distribute your source signals-inch several sets of speakers distributed throughout your home. Additionally a good speaker selector like our 4-Channel A/B Selector listed here will allow you-inch have different source audio sent-inch different rooms so that someone in one room can be listening-inch something different in another room. Most importantly a speaker selector provides impedance matching which ensures that the additional speakers do not overload or damage your Amps. The Monoprice msv-4 is a dual source 4 zone speaker selector with built in independent volume controls for each source. This device can handle up-inch 100 watts per channel. It supports a frequency range of 20hz-inch 20Khz. Accepts wire gauges up-inch 14AWG and maintains load at 8 ohms. Installation is straight forward and simple. This is part of making your dream sound system into a reality.

• Will allow you-Inch have different source audio sent-Inch different rooms so that someone in one room can be listening
• It supports a frequency range of 20Hz-Inch 20kHz.
• Accepts wire gauges up-Inch 14AWG and maintains load at 8 Ohms
• Refer user manual below.

User questions & answers

Question:	Also anyone experience problems with it maintaining an 8 ohm load with the volume knobs set to different levels? I've heard thats a common problem
Answer:	Absolutely Laurie, that is one of the things I liked about this speaker it is very universal on speaker mounting and sound positioning angles as I wanted to be able to point them downward from the higher locations. I definitely recommend these as an (addition) to an existing surround system.
Question:	Can I use this to power a sub woofer through one of the channels
Answer:	This is a single speaker. (I bought 1 and learned that so I bought another)It is worth the price for a pair. They are pretty good above 75-80hz and handle mids and highs well. They take a 30-40w amp. I like them for the money.
Question:	Is this speaker selector Autofromer based or Resistor based
Answer:	They lock perfectly. Not very strong sound, but for some music they do the job well
Question:	I don't see a power cable? Does it not require any
Answer:	Speaker wire is NOT included. You will need your own wire to connect to an amp / receiver.

Product features

Monoprice 4-Channel A/B Speaker Selector

Product Description

One of the most popular trends in Home Audio is whole house audio distribution. Unfortunately, true multi-zone distribution systems are normally built into only the higher end receivers or require an expensive audio distribution network. Monoprice brings everything within reach of the average homeowner by offering a wide selection of Home Audio Distribution accessories.

A Key element of any home audio distribution system is a speaker selector. The speaker selector allows you to distribute your source signals to several sets of speakers distributed throughout your home.

Additionally, a good speaker selector like our 4-channel A/B selector listed here, will allow you to have different source audio sent to different rooms so that someone in one room can be listening to something different in another room.

Product description

Switch selector volume control switch box hub distribution box for multi channel high powered amplifier control 6 pairs of speakers

• Up to 6 Separate Speaker Pairs to your Stereo System
• Accepts Speaker Wires Up to 14- Gauge
• Handles 100Watts Per Channel with Speaker Systems that have a Minimum Impedance of 8 Ohms
• Up to 6 Separate Speaker Pairs to your Stereo System - Support Two Stereo Amplifiers
• Accepts Speaker Wires Up to 14- Gauge - Frequency Response: 20Hz-20KHz
• Handles 100Watts Per Channel with Speaker Systems that have a Minimum Impedance of 8 Ohms - Dimensions: 16.92- Inches(W) x 3.03- Inches(H) x 6.29- Inches(D)
• Protection Circuitry Keeps it Running Smoothly
• Individual Speaker Volume Control

User questions & answers

Question:	can this replace my Pyle Pro PT
Answer:	No, not the devices have the same functions!
Question:	Ok, I bought the PT510 amplifier, and the PSPVC6 speaker selector, but not sure how to connect them together. Can anyone help
Answer:	Ok I'm going to try and keep it simple. Normally, once the amp is connected the 'sound' travels out of the red/white or left/right speaker connectors that are attached then to the speaker system. In your case, think of the speaker box as a 'conjunction' (like the words 'and/ but' in a sentence)..so just connect the 'speaker out' on your amp to the 'speaker in' on the speaker selector box...then connect the speaker box to the 6 speakers...be ready with a small flat head screw driver to open each the speaker connection ports...it's a bit more tedious but assures a professional non clip in/out connection...good luck...and make sure every thing is off to avoid 'blowing out' of the speakers and/or unit.
Question:	Does this have impedance protection - control against low ohms driving multiple speakers
Answer:	http://manuals.pyleusa.com/PDF/PSPVC4-6.pdf The last few pages of manual shows impedance of turning on combinations of speakers It is the amp that needs to be 4 ohm stable, I have a Denon AVR 3300 and AVR 2500. The more speakers active, the lower the impedance, (ohms Law) and the more power needed from the amp According to Crutchfield, we need a 4 ohm stable amp, and the Denon family provides overload protection, and the Denon amps have a 8 ohm (default) and a4 ohm setting I already fried an Onkyo amp, running all the speakers at once, for an extended period.
Question:	Is the Pyle PT510 240 Watt Amplifier a good receiver to use with this. I want to put sound in many rooms in my office
Answer:	I am by no means an AV expert. This amplifier was recommended to me by our AV guy in order to amplify the sound for distribution into several rooms in which we have speakers. We primarily use this amp in connection with an Apple TV device to play music from our iPhone or iPad in our kitchen, den, family room and outside speakers. Hope this response is helpful for you. Kind Regards, Robert

Product features

Premium New and Improved 6 Zone Channel Speaker Switch

Features:

• Multi-Channel High Powered Amplifier
• Up to 6 Separate Speaker Pairs to your Stereo System
• Accepts Speaker Wires Up to 14- Gauge
• Protection Circuitry Keeps it Running Smoothly
• Individual Speaker Volume Control
• Support Two Stereo Amplifiers
• Rugged & Durable Housing Construction, Cabinet Heatsink
• Control Powered 6 Channel Amplifier
• Plug and Play Easy Install

Technical Specs:

• Power Output: 6 x 100 Watts, Power Supply: 120/240V Voltage Selector
• Amplifier Design: 6-Channel, Minimum Impedance: 8 Ohms
• Frequency Response: 20Hz - 20KHz, Signal to Noise Ratio: >81dB
• Channel Separation: 80 dB, Crosstalk between Channels: 50 dB
• Speaker Terminal Wire Size: 14-22 gauge
• Max. Amplifier Input: 100W RMS, 150W AVG
• Max. Output per Speaker: 18W RMS, 50W AVG
• Product Dimension (L x W x H): 6.29'' x 16.92'' x 3.03'' -inches

Product description

Pyle Model : PSLSW4

4-Ch. Speaker Selector System

Multi-Zone Speaker Selector, 4-Channel Audio Speaker Receiver System

Features:

Convenient Audio Control for Up to 4 Pairs of Speakers

Home Theater Stereo Amplifier System Support

Independent Audio Source Channel Volume Controls

Input/Output: Screw Type Connector Terminals

Compact Desktop / Tabletop Receiver Design

Front Panel Button Control Center

Master Power Switch

Built-in Electronic Overload Protection Circuitry

Technical Specs:

Power Handling: 100 Watt MAX Per Audio/Speaker Channel

Speaker Selector Type: 4-Channel

Speaker Cable Wire Support: Up to 14-Gauge (14 AWG)

Minimum Impedance: <8 Ohm

Frequency Response: 20Hz-20kHz

Dimensions (L x W x D): 16.9'' x 6.3’’ x 3.0'' -inches

• 100 WATT MAX: The Pyle Multi-Zone A B Speaker Selector Switch is perfect for your home theater sound system w/ 100W max power per channel. For use w/ 8ohm impedance speakers. Has a compact slim tabletop design that complements any home theater setup
• CONTROL 4 SPEAKERS: The new indoor multichannel speaker switcher controls up to 4 speaker pairs connected to a stereo amplifier at the same time or in combination. Input/output via screw type connector terminals which accept up to 14AWG speaker wire
• INDEPENDENT AUDIO CONTROL: Features independent audio source channel volume controls. The push button design lets you activate each pair individually to customize the listening experience in your home and independently control the volume to each pair
• EASY SETUP: Simply connect the left and right outputs from your amp/receiver and/or another source to the left and right A/B inputs on the mini 4-channel multizone controller, connect up to 4 pairs/8 speakers and enjoy high quality audio performance
• OVERLOAD PROTECTION: Equipped w/ front panel control switches consisting of rotary knobs for volume control and a master speaker switch. Offering high-quality audio, it also provides overload safety protection circuitry and long-term reliability

User questions & answers

Question:	Will fit on slider rack shelf with 16 inches wide and 15 inches deep? thank you
Answer:	Good question. There are two things you should know before you pull the trigger on this. Banana plugs don’t insert far enough to stay put, and since I have this box hooked up to amplified speakers I kept getting a buzz. I bought special banana plug pig tails which I ended up removing because of said problem. What did work very well for me was to remove the banana plugs and strip and solder the speaker wires then tighten the threaded part against the inserted wire in the hole on the shaft, a very tight connection and that worked great. The other issue is you can’t turn off one the speakers which was reported in one of the comments. It is annoying but for my application one set of speakers is downstairs with their own volume control so, I just adjust the volume on them when in use. Hope this helps.
Question:	I don't understand the description. what does the a /b button at each speaker volume control mean? doesn't the speaker pairs selected play together
Answer:	Hi, I have one of these (returning the 1st one due to poor speaker terminal , I find that it will accept a 4mm and thicker Banana Plug. Amazon's model was poor fit, but MediaBridge's plug in more securely. I have not fully connected my XtremePro yet, but I hope this helps.
Question:	Can the speaker connectors take banana plugs as opposed to threading the wires
Answer:	I may not be understanding your question correctly, but with this item I am using the volume control on my amp for the front speakers and the volume on this device to control the volume on the rear speakers. So yes, I can set one set of speakers at a different volume that the other. Again, if I am understanding your question correctly.
Question:	So I can hook up 4 sets of speakers on my new Pyle unit all on one receiver without worry of damage? Looked like chart had impedence fall off to
Answer:	Yes as far as I can tell. Aka-when I only have on speaker on and flip the switch to turn another group on, the volume drops. It’s not necessarily half the volume though.

Product features

4-Ch. Speaker Selector System

This speaker selector box allows you to play audio to up to four different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch and an independent volume control. You can also hook up another amplifier. Protection circuitry keeps it running smoothly.

CONTROL 4 SPEAKERS

The new indoor multichannel speaker switcher controls up to 4 speaker pairs connected to a stereo amplifier at the same time or in combination. Input/output via screw type connector terminals which accept up to 14AWG speaker wire

INDEPENDENT AUDIO CONTROL

Features independent audio source channel volume controls. The push button design lets you activate each pair individually to customize the listening experience in your home and independently control the volume to each pair. Distribute your music to every room in your home with this 4 Channel Speaker Selector from Pyle.

EASY SETUP

Simply connect the left and right outputs from your amp/receiver and/or another source to the left and right A/B inputs on the mini 4-channel multizone controller, connect up to 4 pairs/8 speakers and enjoy high quality audio performance

Protection

Equipped w/ front panel control switches consisting of rotary knobs for volume control and a master speaker switch. Offering high-quality audio, it also provides overload safety protection circuitry and long-term reliability.

Watt

The Pyle Multi-Zone A B Speaker Selector Switch is perfect for your home theater sound system w/ 100W max power per channel. For use w/ 8ohm impedance speakers. Has a compact slim tabletop design that complements any home theater setup

Dimensions

The Pyle Multi-Zone A B Speaker Selector Switch has a (L x W x D): 16.9'' x 6.3’’ x 3.0'' dimensions.

Product description

Pyle Model : PSLSW6

6-Ch. Speaker Selector System

Multi-Zone Speaker Selector, 6-Channel Audio Speaker Receiver System

Features:

Convenient Audio Control for Up to 6 Pairs of Speakers

Home Theater Stereo Amplifier System Support

Independent Audio Source Channel Volume Controls

Input/Output: Screw Type Connector Terminals

Compact Desktop / Tabletop Receiver Design

Front Panel Button Control Center

Master Power Switch

Built-in Electronic Overload Protection Circuitry

Technical Specs:

Power Handling: 100 Watt MAX Per Audio/Speaker Channel

Speaker Selector Type: 4-Channel

Speaker Cable Wire Support: Up to 14-Gauge (14 AWG)

Minimum Impedance: <8 Ohm

Frequency Response: 20Hz-20kHz

Dimensions (L x W x D): 16.9'' x 6.3’’ x 3.0'' -inches

• 100 WATT MAX: The Pyle Multi-Zone A B Speaker Selector Switch is perfect for your home theater sound system w/ 100W max power per channel. For use w/ 8ohm impedance speakers. Has a compact slim tabletop design that complements any home theater setup.
• CONTROL 6 SPEAKERS: The new indoor multichannel speaker switcher controls up to 6 speaker pairs connected to a stereo at the same time or in combination. Input/output via screw type connector terminals which accept up to 14AWG speaker wire.
• INDEPENDENT AUDIO CONTROL: Features independent audio source channel volume controls. The push button design lets you activate each pair individually to customize the listening experience in your home and independently control the volume to each pair.
• EASY SETUP: Simply connect the left and right outputs from your amp/receiver and/or another source to the left and right A/B inputs on the mini 6-channel multizone controller, connect up to 6 pairs/12 speakers and enjoy high quality audio performance.
• OVERLOAD PROTECTION: Equipped w/ front panel control switches consisting of rotary knobs for volume control and a master speaker switch. Offering high-quality audio, it also provides overload safety protection circuitry and long-term reliability.

User questions & answers

Question:	I want to use this on two sets of speakers, one set for front height & second set for side surrounds and switch between the two. Is it possible
Answer:	While you can connect up to four pairs of speakers, this device will not work as a surround sound device like having front, rear, center channels like a Dolby or DTS system. This only splits a stereo signal to multiple pairs of the same exact stereo signal.Hopefully this helps.
Question:	Does this switch allow me to control sets of speakers independently
Answer:	You can control up to 4 sets of speakers independently or play all at the same time! I have switch A for patio speakers, switch B for inside house, sometimes I play A or B or A+B
Question:	One person indicated what they believed the protection button was. Does anybody know? Pyle technical support apparently doesn't exist
Answer:	In modern amplifiers the protection button is actually used to simulate a safe ohm load to the amplifier, not mask the lack of a load. When you connect multiple speakers of certain ohm ratings in series or parallel, it alters the ohm load presented to the amplifier. The switch allows you to attach multiple speaker sets while presenting and "buffering" a consistent/safe ohm load instead of the actual load. 2 x 8 ohm speakers in parallel on the same channel would show up as 4 ohm (divide ohm rating of speaker by number of speakers), which could cause your amplifier to fail (it needs to work harder) if not designed to drive speakers with that ohm rating. If you are using more than 2 pair of 8 ohm speakers simultaneously you would turn on the protection mode to present an ohm load of ~4 ohm instead. Most protection solutions present a 4.5 ohm load in this scenario. Understand that ohm loads are AC and thus are constantly fluctuating during playback. Speaker ohm levels typically will "change" @ different volume levels etc. Low impedance allows for a more efficient electric signal. Typically speakers are rated 4, 6 or 8 ohms. Lower end receivers can sometime have issues driving low impedance 4 or 2 ohm speakers.
Question:	How do I hook this up to my 5.1 receiver
Answer:	Hello Dan,This device is for other areas of a home where you have additional speakers and is not made to be used with the surround sound system. It can be used with "Stereo Receivers" or with 7.1 A/V Receivers where your only using the 5.1 portion of the receiver. What that means is if you have a surround sound system in your home, then all the speaker outputs of the receiver are dedicated to the surround sound and at that point there are no more speaker terminal outputs to be used.However, if your receiver is a 7.1 A/V receiver and your only using it as a 5.1 Surrond Sound System, then you will have 2 additional speaker outputs that aren't being used.At that point you can attach those terminals (via 2 speaker wires a left & a right) to the Pyle 4 Channel Speaker Selector. Now connect the other rooms to the outputs on the Pyle Speaker Selector. ***Make sure you have the correct speakers paired to each individual room when you connect these wires. You can easily determine this by taking a battery from your remote control and placing the ends of the speaker wires to the battery. Positive end of the wire + to the positive end of the battery and the negative end off the same wire to the negative end of the battery, You can hold the negative wire tight to the battery with your thumb while you release and then retouch and release and retouch the positive end a few times. you should hear a popping sound coming out of the speaker. This will let you know which wire goes to which speaker in which room or area. I usually use a "Sharpie" Marker and label the wire "Living Rm" or "Dining Rm" or what ever the room is that the wire goes to. *****Now, and this is most important or you will "FRY" your Pyle unit, make sure the negative wire that is connected to the Pyle output is the same negetive wire that is connected to the speaker terminal in the room where that wire goes and the positive does the same. IF YOU CROSS THE WIRES AND PUT THE NEGATIVE WIRE IN THE POSITIVE TERMINAL, YOU MOST LIKELY WILL GET BAD RECEPTION TO THAT SPEAKER OR FRY (DAMAGE) THE PYLE UNIT AND MAYBE EVEN YOUR RECEIVER. ALSO, MAKE SURE NO BRAIDS OFF OF THE SPEAKER WIRES TOUCH THE CHASSIS OF THE RECEIVER OR EACH OTHER. THIS WILL SHORT THE UNIT.Finally, you may have to go into the setting of your A/V Receiver and select the "Speaker Settings" and scroll to where the "Surround Back" or "Zone 2" Speaker set up is and select "NO". This will deactivate the use of those speakers to be used in the room where the Surround Sound is and will allow them to be used for "Stereo Music" to other rooms.In about 90-100% of all A/V Recievers have to use "Analog" or "RCA Cables" from the device you want to hear the music or sound from in the rooms that the Pyle is hooked up to. FM Tuner (or radio stations), Pandora and Internet Radio Stations are already incorporated in the receiver and will play with no problem.Now just select "Zone 2" on the Receiver and press the "Input" selection you want to hear in those other rooms. Raise the Zone 2 Volume Level for those rooms and you should hear music or audio. Please note that some receivers have a time period of 5-6 seconds for you to do these steps, so when making your audio selection and volume level, know where your audio selection button is that you want before performing these steps or your Receiver timer will time out and you will have to permorm them again. It can be frustrating at first for a novice. It was for me. Sometimes still is. LOLA couple of things to know. I would only use this device if I had "Individual Volume Controllers" in each of the rooms or areas where I want Music or Sound. If you don't, then the "volume level" will be the same in all those areas. Volume Controls allow you to do what they say, they can "Control" the volumes level. If the Music or Sound is too High in one room, it might be too Low in an other room. Volume Controls correct that.If you don't have individual Volume Controls in the rooms where your speakers are, then you want to purchase the Pyle Home PSPVC4 4-Channel High Power Stereo Speaker Selector with volume Control. http://www.amazon.com/Pyle-PSPVC4-4-Channel-Speaker-Selector/dp/B0013CH7UK/ref=sr_1_1?ie=UTF8&qid=1376744129&sr=8-1&keywords=Pyle+Speaker+Selector+with+Volume+Controls If you have any issues getting the sound to pass through Zone 2 of your Receiver, contact the units manufacturer and ask for tech support.I hope this helps.Ken Nichols, PresidentSIGHTS & SOUNDS OF SOUTH FLORIDA, INC.3801 Environ Blvd.Fort Lauderdale, FL 33319305-788-1895

Product features

Premium New and Improved 4 Zone Channel Speaker Switch Selector Switch Box Hub Distribution Box

This speaker selector box allows you to play audio to up to eight different stereo speaker sets. It easily handles up to 100 watts per channel with speaker systems that have a minimum impedance of 8 ohms. Each input has an on/off switch. Protection circuitry keeps it running smoothly and prevents speaker burn-out. Accepts speaker wires up to 14 gauge.

Product description

The SSVC-4. 1 Speaker Selector is a resistor-based, impedance matching speaker selector used for connecting up to four pairs of 4-ohm or 8-ohm speakers, while maintaining a safe impedance load for your amplifier or receiver. Each pair of speakers can be independently turned on or off using push buttons on the front panel, with no need for worrying about amplifier loading. Each zone features an independent volume control.

• Connect and safely control multiple speaker pairs with a single amplifier. Automatic impedance protection circuitry.
• 100 watts/channel continuous power handling capacity, 200 watts/channel peak. 5-ohm minimum amplifier impedance with four 4-ohm speakers selected, 6-ohm minimum with 8-ohm speakers.
• Individual zone on/off buttons and volume controls.
• Heavy-duty screw-type connectors supporting 12-18 AWG speaker wire.
• Isolated left/right circuit grounds provide safe connection for amplifiers with floating grounds or bridged configurations. Accurate, noise-free switching.

User questions & answers

Question:	Input from sony str-dh190 and out to 3 zones but no audio; tried connecting 1 zone and still no audio - tried 6 & 8 ohms - any other recommendations
Answer:	Make sure the input volume is up (Bluetooth, aux from phone or aux) amp volume should be up at least 50%-75%. Then turn up the SS4 vc. Should be on 8ohm, button pressed in (in the on position) and select A or B depending on what you have it plugged into the back.
Question:	Is there a warranty
Answer:	Yes it comes with an one year warranty.
Question:	Monoprice, can I connect 1 pair of rated 8 ohm (nominal 6 ohms - Elacs speakers and a different pair of 8 ohm speakers to play simultaneously
Answer:	Yes, that is the whole point of this product - to allow one amplifier to drive several pairs of speakers, with independent volume control over each pair, and impedance protection to protect the amplifier.
Question:	What does l- l+ r- r+ mean
Answer:	L is for the left speaker and R is for the right speaker.

Product description

PyleHome Model : PVCD15

Volume Control Wall Plate

In-Wall Right and Left Speaker Dual Knob Independent Volume Control Plate

Dual Independent Volume Controls

120 Watt Load Handling Power

Independently Control Two Separate Stereo Channels (Right and Left)

Rotary Knobs for Clean, Smooth Volume Adjustment

Attractive and Standard/Universal Style Wall Plate Included

The PVCD15 In-Wall Volume Control System is a convenient, easy way to control the volume of your home speakers. This dual-knob wall plate installs in a junction box in your wall, just like a light switch. It's unobtrusive, clean, and matches your decor. Control up to 2 speakers with the independent rotary faders. Standard and universal style wall plates included.

• EASY TO INSTALL: The Pyle in-wall stereo volume control installs in a junction box, just like a light switch. Fits standard electrical junction/gang boxes. Makes it simple and easy to direct your home amplifier audio to 2 sets of speakers
• ROTARY KNOB OPERATION: The indoor outdoor speaker controller features a convenient and simple rotary knob controls which makes volume adjustments a breeze! Control up to 2 speakers with the two independent rotary faders
• OPERATION: Set the amplifier's volume control to minimum. Turn on the amp and set its volume control slightly above the normal listening level. To increase/decrease the remote speaker's volume turn the inwall volume control clockwise/counterclockwise
• UNIVERSAL COMPATIBILITY: The 2 channel speaker volume fader is compatible w/ all audio and video systems making it a wise choice to add to your home theater system. It also features up to 120 watts load handling power
• STANDARD SIZE: It features a universal standard wall plate size. The included decora-style wall mount plate frame cover means this controller will unobtrusively blend into your wall and allows for a clean installation on your walls

User questions & answers

Question:	Instructions are unclear vs markings on the unit. does '+' mean in ..and '—' mean com? (it appears such in the schematic) jim
Answer:	Yes. We put a speaker selector on it and have it wired to 2 sets of speakers. 1 set has 2 speakers and 1 set has 4 speakers.
Question:	What colors does this control come in
Answer:	Hi sounds like you dont want to see the tranformer , with cable running down the wall. What I did with mine if you know about wiring electrical and things like that I cut the wire from my Transformer to the unit and I made it longer and I run a wire up into my attic where I have a light switch with a plug .plugged in the transformer ,made the wire longer so now it's a hard wire unit basically that's what it looks like because all you see is just the unit in the wall with the faceplate no wire sticking out of it and that's how I did mine don't know if you have access to your attic and if you have a light up there with an outlet but that will be the best way to have a clean job for it, hope this will help a bit, also to your question, this unit comes with a 120v to 12 volt dc converter
Question:	Can I use this for two source inputs and one output? IE: Channel A = (inA, comA = Chromecast); Channel B = (inB, comB = other source); out=speakers
Answer:	I assume you are referring to the bluetooth name. I have 6 units, they all use the same name, but that isn't a problem, because they don't advertise unless you push the volume knob. After you pair each one, rename it on your phone, no need to rename on the receiver, the phone can tell them apart. So if you have previously paired to a phone, when you turn the unit on it will try to reconnect to its existing paired device. If you want to pair to a new device, press the volume knob while you are scanning for devices from your phone, then rename it in bluetooth settings on your phone after it is paired. The only time you are going to have an issue is if you press the volume knob on 2 devices at the same time, you wont know which is which, but since you probably cant be in 2 rooms at once to do that, shouldn't ever be an issue, and whichever one it pairs to, you can rename to distinguish which is which..
Question:	Does this control 2 speakers or 2 pairs of speakers? The pictures are deceiving and I don't see it noted. Thanks
Answer:	try Pyle Audio www.pyleaudio.com

Product description

The SSVC-6.1 Speaker Selector is a resistor-based, impedance matching speaker selector used for connecting up to six pairs of 4-ohm or 8-ohm speakers, while maintaining a safe impedance load for your amplifier or receiver. Each pair of speakers can be independently turned on or off using push buttons on the front panel, with no need for worrying about amplifier loading. Each zone features an independent volume control.

• Connect and safely control multiple speaker pairs with a single amplifier. Automatic impedance protection circuitry.
• 100 watts/channel continuous power handling capacity, 200 watts/channel peak. 4.6-ohm minimum amplifier impedance with four 4-ohm speakers selected, 5.3-ohm minimum with 8-ohm speakers.
• Individual zone on/off buttons and volume controls.
• Heavy-duty screw-type connectors supporting 12-18 AWG speaker wire.
• Isolated left/right circuit grounds provide safe connection for amplifiers with floating grounds or bridged configuration. Accurate, noise-free switching.

User questions & answers

Question:	In the picture, the speaker wire jacks look flimsy. Will they really handle 12 gauge speaker wire? Thanks for mentioning automatic impedance adaptat
Answer:	Yes, it is adjustable within the limits of its mounting. Rotation is 360 degrees then connect. Sounds silly, but.....I am very satisfied with mine!!!!!!!!!!!!

Product features

Puppy Dog Pals: Volume 1 DVD

They're cute, cuddly and all collared up for pup-tacular adventures! Puppy Dog Pals: Volume 1 is a collection of adventures featuring the fluffy stars of the popular Disney Junior series.

Magic in the details

While their owner Bob is away, adorable puppy brothers Bingo and Rolly embark on wacky missions stretching from their own backyard to amazing locations all around the world! With support from their ''big sister'' Hissy, a neighborhood full of animal friends and Bob's high-tech inventions, these hilarious heroes are always ready to unleash plenty of fun.