13 best jack accessories

• SAFELY LIFT YOUR VEHICLE WITHOUT DAMAGE: The ABN Large 5.5-Inch Pinch Weld Jack Pad Car Jack Puck 1-Pack is a floor jack pad that prevents the jack from exposing structural metal and is designed to protect the pinch welds, your vehicle under chassis, and overall frame so you can safely lift your vehicle at the proper jack points without scratching paint or causing metal-on-metal damage while using a hydraulic jack
• BUILT FOR SAFETY: This floor jack rubber pad is constructed from stiff rubber that cushions your car from damage and increases safety when secured properly; Bottom side of slotted rubber jack pad includes textured grooves to ensure correct and safe fitment on jack without slippage
• USE YOUR JACK: Top side of car jack pad has slotted crosshairs to align with and protect side pinch welds while the bottom of the jack lift pad is also keyed with 4 recesses that fit onto 4-inch cup rim lugs on your jack to prevent the pad from spinning on the floor jack cup (cup and pad contact starts between these lugs)
• LARGE SIZE: Fits beveled 5.5-inch steel lift cups bowl saddles on standard hydraulic floor jacks; Floor jack saddle pad has 5.5-inch (14cm) top diameter and 4-inch (10.2cm) bottom diameter, 1.75-inch height (4.4cm), 4 slots have approx. 0.4-inch width and 0.75-inch depth (1cm x 1.9cm); To ensure fitment, measure ID of your jack and compare to 5.5-inch diameter of this jack rubber stabilizer pad while ensuring your vehicle has enough clearance – this jack stands pad adds 1 inch (2.5cm) to height
• PACKAGE CONTENTS: Stabilizing jack pads package includes 5.5-inch pinch weld protector slotted jack pad to best suit your needs – Jack rubber pad only – jack not included

User questions & answers

Question:	Has anyone used this successfully on a Nissan 370 Z
Answer:	The photo of the product is not the best. The bottom side looks like 2 diameters but it is actually 3. The smaller portion with the 4 notches has a diameter of 4 1/16 inches and is 3/8" thick. The next portion is 4 9/16 by 3/32. The last one is roughly 4 15/16 to 5" by 3/16. Hopefully this sheds some more light on the dimensions of the bottom side; 3 successive sizes to create a taper.
Question:	How wide is the bottom cross section? i have a harbor freight low-profile/high-lift jack and i think that the saddle is only 4 inches across
Answer:	No
Question:	Will this fit a regular 3 ton Pittsburgh jack
Answer:	There made for a 5 1/4 to 6 1/2 speaker you will need to cut the hole for the size of the speaker your going to use. There not for a subwoofer. There for a component speaker. Like a two way speaker or a midrange for like mounting to the fire wall or door panels. I have a pair of JBL midrange speakers that set 3 inches deep and fitment is good
Question:	What are the dimensions of the underneath, there looks like there is 2 different sizes
Answer:	Outside as with weatherproof speakers? Highly doubt they would not fade over 5+ years in the weather. You can always spray them with a coating like Rhinoliner or the such as to provide a coating between the weather and the plastic.

Product features

About the ABN 5.5-Inch Jack Pad 1-Pack

If you use a plain jack plate as is, the pinch welds and other frame support members can bend and damage your vehicle since the jack plate is a hollow bowl-like shape that places the full weight of the car to be supported on just 2 points. But what are the options when it comes to adding a cushion between a metal floor jack cup and the painted underbody when lifting a car?

Instead of risking scratches and other damage to your car, use the ABN 5.5-Inch Frame Rail Jack Pad 1-Pack.

• COMPATIBILITY: This off raod base compatible with most Hi Lift Jacks, like All-Cast Jack, Cast/Steel Jack, X-TREME Jack, UTV Jack, Patriot Edition Jack, Equipment/Agriculture Jack(EJ-550). NOTE: D0ES NOT fit for Smittybilt 2722 & hi lift Jack PP-300 Post Popper.
• QUALITY MATERIAL & HEAVY DUTY: Made of a tough PP synthetic material,thick and sturdy materials. This base was enough to keep the Hi-Jack from slipping and sinking into the mud while you are hoisting the vehicle.
• WITH SERRATED TEETH: Use the teeth to level out the ground before Jacking, the jagged edge helps to scrape at hard dirt or gravel, to create a clean, flat surface for the base to sit on while in use.
• THICK & BRIGHT COLOR: The widened bottom plate is suitable for use on soft ground to prevent the jack from sinking and slipping; The bottom is hexagonal which increases the contact area between the base and the ground, it is more stable and does not slip during use. The red color is very easy to be found in the mud, you won't lose it.
• EASY TO STORE AND CARRY: It can be stored under the seats or put the Hi Lift Jack base in the trunk. Also a drilled hole in center of base attached to your jack bar.

User questions & answers

Question:	can it be used on front landing gear for a toy hauler( 13,500lbs
Answer:	Yes it is a hardcover.

Product description

What’s worse than not having a lifting jack? Watching the jack slowly sinking into the ground! With our lifting jack base going under your lifting jack and making it much more stable to help alleviate your jack sinking into sand, mud snow or other soft surfaces. It's convenient to use, and easy to store. Our jack base is compatible with most hi lift jacks includes model all-cast jack, cast/steel jack, X-treme jack, UTV jack, patriot edition jack, and equipment/agriculture jack EJ-550. (Does not fit post popper jack, please check your lifting jack size before purchase – It only works on jack base within 7’’ x 4’’). Our Base's rugged construction meets or exceeds OEM specifications for strength and durability for years of use. The bottom of the base is textured for a better grip. In the center of the Base is a hole (about 3/8 diameter") that goes through it, so you can insert a long hardware bolt and mount the base wherever you want (bolt not included). Easy Visibility: In a bright red, you’ll spot it quickly on the ground and never leave it behind.

• What’s worse than not having a lifting jack? Watching the jack slowly sinking into the ground! With our lifting jack base going under your lifting jack and making it much more stable to help alleviate your jack sinking into sand, mud snow or other soft surfaces. It's convenient to use, and easy to store.
• Our jack base is compatible with most hi lift jacks includes model all-cast jack, cast/steel jack, X-treme jack, UTV jack, patriot edition jack, and equipment/agriculture jack EJ-550. (Does not fit post popper jack, please check your lifting jack size before purchase – It only works on jack base within 7’’ x 4’’).
• Our Base's rugged construction meets or exceeds OEM specifications for strength and durability for years of use.
• The bottom of the base is textured for a better grip. In the center of the Base is a hole (about 3/8 diameter") that goes through it, so you can insert a long hardware bolt and mount the base wherever you want (bolt not included).
• Easy Visibility: In a bright red, you’ll spot it quickly on the ground and never leave it behind.

Product description

Fits most floor jacks and vehicles, please check fitment below, does not fit Trolley Jacks

• Made from highly durable rubber
• Designed to be sturdy enough to support your lift point while soft enough to preventing crushing the contact area
• Pad Dimensions: 72mm Diameter 33mm Height, Slot Dimensions: 10mm Wide 13mm deep
• Prevent your frame rails and pinch welds from bending when using a Jack to lift your car
• Fits most floor jacks and vehicles, please check fitment below, does not fit Trolley Jacks

User questions & answers

Question:	What are the measures
Answer:	No but the stats are there for you to fill out a blank sheet. Catalyst does provide a separate product will pre-generated record sheets. This product is the lore of the units and history as well as the game stats for each unit, like all other Technical Readouts.
Question:	What is the weight limit for these? I’ve seen a few reviewers have problems with compression
Answer:	Hello, thank you for your inquiry. This is just the Tactical Readout. This is not the clan invasion kickstarter.
Question:	Will this work with a bottle jack
Answer:	yes it is a bit of an over sized paperback sort of the size of a legal pad.

• COMPATIBLE WITH MOST HI-LIFT JACKS:Designed and Used for most of Hi-Lift jacks, Includes model All-Cast Jack, Cast/Steel Jack, X-TREME Jack, UTV Jack, Patriot Edition Jack, Equipment/Agriculture Jack(EJ-550). Do not fit for POST POPPER Jack
• ALLEVIATE JACK SINKAGE ON SOFT GROUND: Used on soft ground like sand, mud, grass. Give the Off-Road Base better footing and greater stability during the lifting process
• HEAVY DUTY AND EASY TO CARRY: Made of a tough PP synthetic material, better more than a chunk of wood will not rot or break. A drilled hole in center of base attached to your jack bar, store it easy
• ONE SIDE WITH SERRATED TEETH: Helps to scrape at hard dirt or gravel, to create a clean, flat surface for the base to sit on while in use
• NO-RISK PURCHASE! UNCONDITIONAL 30-DAY MONEY-BACK GUARANTEE. If you’re unsatisfied with this item for any reason, we’ll immediately refund your purchase price

User questions & answers

Question:	Will it fit the farm jack
Answer:	according to amazon site the y measure 72 mm diameter, 33mm height,. the slot is 10 mm wide and 13 mm deep. i used them to jack up my kia forte 5 with a real low follr jack9Harbor Freight). i have sold the car and now use them on whatever the need present s itself. they are durable and take a lot of punishment and my son and son in law use them often. two are presently under a jeep as i type. Good Product ernest
Question:	Does this come with bolt and wingnut to attach to jack when mounted externally on jeep
Answer:	I don't specifically know the weight rating, but they are a solid, hunk of Urethane. I would trust them to lift a semi. There is really nothing to fail. There is no jack that can lift enough to damage them. I did have to cut slots and slightly shape two of mine to go around the pinch welds on the factory jack points.
Question:	Can this be used with OEM vehicle jack - or only high-lift
Answer:	they should. typically bottle jacks have much smaller contact surfaces than floor jacks so i would be careful that these pads are perfectly centered, but i see no reason they won't work with a bottle jack.
Question:	Will this work with a 6 ton bottle jack? Base is 4.5” X
Answer:	If you know that it fits the footprint of the landing gear you can try it. Presumably the foot of the landing gear is spec’d to handle the down pressure of the rig. Also that won’t be 13,500 pounds but something a lot more manageable. If the jack pad fits the landing gear it’s going to significantly reduce the ground pressure, pounds per square inch, by increasing the square inches. The pad is made of HDPE with a grid structure and it would take a phenomenal effort to damage it.

Product features

About Seven Sparta Off-Road Base for Hi-Lift Jack

Fit All-Cast Jack: HL-425 (42"),HL-485 (48"),HL-605 (60")

Cast/Steel Jack: HL-364 (36"),HL-424 (42"),HL-484 (48"),HL-604 (60")

X-TREME Jack: XT-485 (48"),XT-605 (60")

UTV Jack: UTV-364 (36"),UTV-424 (42")

Patriot Edition Jack: PAT-485 (48"),PAT-605 (60")

Equipment/Agriculture Jack(EJ-550)

Heavy Duty & Easy To Carry

Made of a tough PP synthetic material, better more than a chunk of wood will not rot or break. A drilled hole in center of base attached to your jack bar, store it easily.

One Side with Serrated Teeth

Helps to scrape at hard dirt or gravel, to create a clean, flat surface for the base to sit on while in use.

Much Sturdy

It will keep the Jack from sinking in swampy Spring mud, when using a Hi Lift jack for anything heavy, when jacking on a trail or the edge of the Mud Hole.

Product Description

Color: Red

Material: PP

Size: 11.8*11.8*2.8”

Package Include: 1* Jack Base

Product description

Installation Step: 1. inserting the adapter pad into the vehicle jack point hold. 2. screws tight the jack pad by hand. 3. pads are preinstalled. 4. connect to your jack or lift.

【Great customer service】 if you have any issue after receiving our products, please contact us through the email in our customer service card in our product package, and we would be happy for a replacement or refund.

• Function: there are specific lifting points for the Model 3. Without an jack pad adapter, lifting the vehicle to turn the tires can damage the vehicle's battery.
• Protect the car's chassis from chipping and harm. Designed for Tesla vehicles. [Note] if you own Tesla Model X, you may need to line up the cushions in the holes to avoid looseness when raising the car.
• Storage bags keep jack lift pads organized. Easy to store in your trunk or garage.
• Size: bottom diameter * bottom height =3.03'' * 0.15', top size = 1.02'' * 1.02'' mm, weight = 156 g. there may be a 1-2mm error, suitable for most vehicles.
• Easy to use: Insert the adapter pad into the jack hole and position the jack directly under it. Just make sure the jack is centered on the adapter pad.

User questions & answers

Question:	Will they fit a Model Y
Answer:	Mine didn’t, I keep mine under my back seat of my JKU. Hope this helps.
Question:	Will these work on model y
Answer:	Never tried it but I’m sure you could make it work.
Question:	Does the rubber washer have a rubber smell
Answer:	The area that holds the jack in place has these dimensions: 11.4cm by 19.1 cm (I am German!). The increase in height for the jack is about 7cm. The surface of the pad feels slippery. I would not recommend this thing. I think a piece of wood would serve the purpose better.