13 best lucas engine additives

Product description

Lucas Engine Break-In Oil Additive protects camshaft lifters and valve train during break-in periods of motors. It is excellent for flat tappet camshafts during break-in or as an additive to any motor oil to prevent premature wear.

• Affordable Solutions
• Not designed for passenger car use
• Exclusive blend of extreme pressure additives
• Excellent for flat tappet camshafts or as an additive

User questions & answers

Question:	How many quarts does this treat
Answer:	I used two bottles when breaking in a marine engine with 8 qts capacity.
Question:	What are the zinc and phosphorus concentration rates? Are there any dilution charts
Answer:	Lucas Product# 10063 is a zinc additive for engine oil. Its designed for engines with no catalytic converter in the exhaust (pre-1977 cars/trucks) and race engines. This product is also used as an engine "break-in" additive for newly built engines. For non-race applications, one bottle will usually treat two oil changes. Some race-engine applications require the entire bottle. Classic cars (depending on oil capacity) require approximately 2,100 PPM (Parts Per Million) zinc in the oil. Phosphorus levels are not published for this product. Coupon Available. Voted Top in service, warranty and support. Thank you for your interest. FamilyGoKarts 800-950-2210
Question:	How much do you add
Answer:	16 ounce bottle each oil change to protect your engine. However much engine oil you normally add during and oil change, make sure you substract 16 ounces. Then add TB Zinc Plus.
Question:	how man oz should i use per quart
Answer:	1 bottle with standard crank case capacity (4-6) quarts. Pour in bottle first, then add oil to full mark.

Product description

Lucas Oil Hot Rod and Classic motor oil is manufactured with the quality paraffinic base oil and fortified with a additive package containing of zinc, molybdenum and phosphorus, which provides a tougher, thicker additive film for protection even under the most severe conditions. It lowers oil temperatures, extends oil life and minimises metal fatigue. It improves the film strength between the cylinder wall and piston rings, slows oil burning and improves pressure in worn engines. It has good cold temperature properties and stands up to high operating temperatures. It is compatible with methanol and all racing fuels, as well as with synthetic and non-synthetic oils.

• Lowers oil temperature
• Minimizes metal fatigue
• Improves pressure in worn engines
• Contains the high levels of zinc necessary to protect flat tappet cams, lifters and pushrods

User questions & answers

Question:	Be good for a 1988 305 chevy motor
Answer:	Not sure what SAPS is
Question:	can it be use on 67 mustang
Answer:	If you have a turbocharger you should definitely use Lucas.
Question:	Whats the difference in this thats 32.00 and the 5 single quart bottles thats
Answer:	Had start up noise on my 2013 Hyundai Santa GLS, dealer says it's nothing but engine fuel pump, GDI on top of valve cover (@500.00) making noise , common on GDI systems after I asked @. 90000 I am still running 5W-20 full synthetic mobile 1 . changed oil /filter put in quart of this guess what...be 5500 + miles and still no noise ....saved me from changing that part...and even when I have to stomp down on still no noise...:) : )
Question:	Can i use this engine oil on my 1997 gmc suburban?and would it help quite the lifter ticking
Answer:	No, use fuel treatment solution solely

Product description

Lucas Oil Stabilizer is a 100% petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine. It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures.

• Formulated To Eliminate Dry Starts And Reduce Friction, Heat And Wear In Any Type Of Engine
• It Allows Motor Oils A Higher Degree Of Lubricity Which Reduces Oil Consumption And Operating Temperatures
• Through Creativity, Productivity And Innovation - This Brand Continues To Develop The Finest Automotive Accessories

User questions & answers

Question:	How much of the gallon do you use in a 15 quart Diesel engine when you change the oil and filter
Answer:	4 quarts in a gallon.. You are using 15 quarts which is about 3.75 gal. of diesel oil. On the bottle it says put in 20% or 1 qt stabilizer for 4 quarts of motor oil (total = 5 quarts).. So, about 4 quarts stabilizer or 1 gal. for your big diesel sir.. I'd substitute a gal. of stabilizer for 1 gal of diesel oil.. Remember to substitute the gal (2.75 gal. of diesel oil) and add one gal. of stabilizer = 3.75gal.
Question:	how much do I put in at my next oil change? I have a toyota 4runner 5quarts. Thanks
Answer:	1Quart...Remember, it's 20% of your engine oil capacity....
Question:	This product can be used in diesel engines
Answer:	Yes this product can be used for Diesel engines . It can used for either motor oil or transmission oil
Question:	Is this for a 1 Gallon Bottle OR 4 Quart sized Bottles? Description says 4 per case
Answer:	I am not finding where it says "4 per case" but the image is the 1 gallon and I order 1 and received a single 1 gallon container.

Product description

Lucas Engine Oil Stop Leak is an all new formulation of Lucas additives and very specific base stocks designed to stop seal leaks in engines.

• Compatible with petroleum, semi-synthetic and full synthetic motor oils
• Renews worn seals with no risk of damage or eventual corrosion
• Reduces engine noise and oil consumption, while raising oil pressure
• Contains no harmful solvents

User questions & answers

Question:	It's ok for diesel semi truck
Answer:	If a customer asks for this service to be done.
Question:	Will this product freeze if left in an engine that's just sitting in freezing weather for several weeks
Answer:	The date on the bottom of the can is the production date, not the expiration date
Question:	Hello how liters of engine will this treat? I have about 36 liters in my truck
Answer:	There is no way of telling if your vehicle engine has sludge unless you take it apart completely. The best way is to use a professional grade oil cleaner such BG EPR. I've seen engines that had an oil change every 3000 miles and after adding the BG EPR; the oil turned black.
Question:	Does this seal oil filter gasket leaks if left slightly loose
Answer:	Yes. Absolutely. My BG rep. states and I quote"if you really wanted to you could use it every oil change beginning at 5,000 miles. I only really recommend it every 15,000 though in my experience

Product description

A pure petroleum multi-use oil supplement. Controls noise, heat and wear in manual transmissions and differentials. Number one in the heavy duty and high performance industries. Lucas Oil Stabilizer is a 100 percent petroleum product formulated to eliminate dry starts and reduce friction, heat and wear in any type of engine. It allows motor oils a higher degree of lubricity which reduces oil consumption and operating temperatures. Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil. Since it is pure petroleum, it can safely blend with all other automotive lubricants, even synthetics, ATF and mineral oil. It keeps old engines alive and new engines new.

• The product is 32oz hd oil stabilizer
• Easy to use, increases power and miles per gallon
• Made in USA, increase oil life at least 50 percent longer

User questions & answers

Question:	Can you use this regardless of the weight of your conventional oil? (5W20 is needed in my Element
Answer:	Yes, mixes with all oils. Great stuff. But, should be used with conventional oil You can use it with synthetic but, if you are running synthetic, you should use: https://www.amazon.com/Lucas-LUC10130-Synthetic-Stabilizer-Quart/dp/B000ARPVNY/ref=sr_1_2?s=automotive&ie=UTF8&qid=1538692369&sr=1-2&keywords=lucas+synthetic+oil+stabilizer
Question:	Can I put this in a 2000 Honda Civic manual transmission
Answer:	Yes but not a lot older Honda’s manual transmission run engine old don’t put transmission oil it it people don’t know what they are talking about given you answers back
Question:	How do you use this product
Answer:	I use it in place of one quart of oil at oil change. I use this on all of my non-synthetic oil vehicles, and the synthetic Lucas in my cars (Cadillacs) that use synthetic oil. I am a drag racer and I use it with race oil in all engines I own. Once you see the insides of one of your high-mileage or severe condition engines that has been using Lucas additive, you'll be a believer like me. I use Lucas break-in additive in all new engines. That's how strongly I feel about Lucas products.
Question:	I have a toyota corolla. i just got the oil changed so i don't want to drain it. how much should i add to the oil
Answer:	I would add half....then wait 1500 and add the other half....you can top off with it. I prefer to use it in the summer because today's manufacturers recommend such thin oils such as 0W-20....

Product description

Eliminates noise and wear associated with today's light weight motor oils. Use with synthetic and non-synthetic oils. Cuts internal friction for more power. Made in USA. 1 Quart.

• Fit Type: Universal
• Use With Synthetic And Non-Synthetic Oils
• Through Creativity, Productivity And Innovation - This Brand Continues To Develop The Finest Automotive Accessories
• Country of origin : China

User questions & answers

Question:	I can use it without an oil change
Answer:	We were wondering that same thing. We thought we were getting 12 and only got one. Not happy at all.
Question:	Has any one noticed improvement in oil consumption
Answer:	5W40 Motor Oil Suitable for VW/Audi 500.00/501.01/ 502.00/505.00/505.01, BMW LL-01, water-cooled Porsche A40 and Mercedes-Benz 229.1/229.3/229.5 applications
Question:	So what does this do to the oil? Your engine? And how does it help a 6.4 liter power stroke
Answer:	As long as your engine is still stock you are better to use the proper grade oil. Ford recommends 5w20 in most their applications. You “MAY” still get your noise to quite down and or go away by using redlines 5w20. Their oils tend to be in the upper limits of the accepted viscosity ranges. They also use a very robust additive pack.
Question:	What is the difference between this and the lucas 10001 heavy duty oil stabilizer
Answer:	Overkill in my opinion. It’s an Ester based oil, which Nissan didn’t start recommending until 2008.

Product description

Lucas Oil 10016 Fuel System Cleaner; Use To Clean/ Lubricates And Fuel Stabilizer For Entire Fuel System And Integral Engine Parts; 16 Ounce Can

• 6 PACK
• Compatibility: Clean/ Lubricates And Fuel Stabilizer For Entire Fuel System And Integral Engine Parts
• Unit Size: 16 Ounce
• Contains Special Lucas Additives That Cause The Fuel To Burn Thoroughly For Fewer Exhaust Emissions And More Miles Per Gallon
• Removes Harmful Deposits On Intake Valves And Cylinder Heads

User questions & answers

Question:	Is this listing correct as a 12 pack of 16 oz bottles for a total of 192 fluid ounces
Answer:	No, this is to treat ethanol-based fuel for storage. I recommend you find a gas station that has a premium with no ethanol.
Question:	Should i use this in a new car that i bought in sept 2020 and has 2k miles on it
Answer:	Yes, you receive 4 one gallon jugs for this price.
Question:	Would this fix a low egr flow check engine light
Answer:	Conventional non-synthetic oils for an ‘88 305 would be just as good. The Lucas oil is for my 50-year-old cars and is more expensive.
Question:	I have a 6.4 liter power stroke. Does this stuff really work? And what exactly does it do? Is it like the sea foam
Answer:	this would be a great oil for 1967 289 motor.

Product description

Lucas Engine Oil Stop Leak is an all new formulation of Lucas additives and very specific base stocks designed to stop seal leaks in engines. Compatible with petroleum, semi-synthetic and full synthetic motor oils.

• Compatible with petroleum, semi-synthetic and full synthetic motor oils
• Renews worn seals with no risk of damage or eventual corrosion
• Reduces engine noise and oil consumption, while raising oil pressure
• Contains no harmful solvents

User questions & answers

Question:	I have a 4.3 liter volvo penta i/o boat engine that has a small leak. i use 20w-40 oil. can i use this in a boat engine runs up to 4500 rpms
Answer:	you of course can use it, but will it fix your leak no, it will slow it down but will not stop it. lucas oil products are nothing more than super thick oil kinda of like pouring very thick gear oil into your engine. you are using a very thin oil, i would think because of high rpms & heat your oil needs to move fast & freely to keep all parts lubed. talk to a penta dealer but i'm guessing they will tell to fix the leak correctly with a new gasket or replacement part to cure the leak
Question:	Can i use both this and the lucas oil stabilizer at the same time
Answer:	I pulled this info from the vendor.Use Lucas Oil Stabilizer in gear oil to stop leaks, reduce operating temperatures and increase the life of the gear oil. Since it is pure petroleum, it can safely blend with all other automotive lubricants, even synthetics, ATF and mineral oil. It keeps old engines alive and new engines new.
Question:	questions: Does this need to be added every oil change like other products? Is it really thick like Motor Honey? Thanks
Answer:	No, you don't need to replace it on every oil change. This additive mixes with your motor oil and coats the inside of the engine as well as the seals (where usually the leaks comes from). As I've mentioned before don't overfill this two mixture (your motor oil & Lucas Stop Leak) beyond your engine's capacity. Once you've drained your old oil and replaced the drain plug & new oil filter on your vehicle carefully add the Stop Leak then the additional motor oil, checking on the dip stick every now and then while adding them, so as not you won't overfill the engine.'Motor Honey', I haven't come across this product. Is this just a figure of speech?
Question:	how do I use lucas oil stop leak
Answer:	When you change your oil put the stop leak Quart in in place of 1 of the Quarts of oil,then drive regular till next oil change.Unless your leak is extreme Lucas will stop the leak. I've used all the Lucas products for years in my cars and my 18 wheeler before i retired. Now i still use it in my personal vehicles. Love that Lucas!

Product description

Lucas Fuel treatment complies with the federal low sulfur content requirements for use in diesel motor vehicles and non-road, locomotive and marine diesel equipment engines. A powerful blend of oils and additives that contain no solvents. Designed to increase power and fuel mileage and also lower exhaust emissions through a more complete combustion. Formulated for both gasoline and diesel engines, carbureted and fuel injected. It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency. Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas Fuel Treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions. Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.

• The product is 5, 25 ounces, fuel treatment, for gasoline LPG and diesel fuel, contains no alcohol/solvents/kerosene/diesel fuel, lubricates rings and cylinder walls for longer life, increases mileage, cleans and lubricates valves, pumps, carburetors, and injectors
• Easy and simple use kit
• The product is manufactured in China
• A great tune-up in a bottle
• Cleans and lubricates the fuel system
• Neutralizes low sulfur fuel problems
• Increases power and miles per gallon by burning excess exhaust emissions
• Increases the life of pumps and injectors

User questions & answers

Question:	How often can you use
Answer:	I use this on every fill up because it lubricates the upper cylinder which increases my gas mileage by about 9%. So it definitely pays for itself. Tho I buy it a gallon at a time and use the smaller bottle to pour into my gas tank. Also, I only put about 7 or 8oz in a 20 gallon tank. Too much of this stuff actually lowers gas mileage. I know from personal experience. If you're looking for a one-per-year cleaner, you really need to look at Techron. This Lucas Oil fuel treatment isn't a strong enough cleaner to use only once per year. I use Techron every other oil change to keep injectors and whatnot clean, but use this Lucas Oil treatment for MPG gains only (from lubricant affects).
Question:	Can i Use this in a Toyota corolla 2006? and how often should I use it
Answer:	My Toyota dealer sells this product in their service dept
Question:	Can I use this in my 2012 kia sorento
Answer:	You have to add this before you fill your vehicle up. That way the very action of the pump pumping gas into your vehicle mixes up the Lucas Oil. You don't want to put it in after you filled your gas tank
Question:	Will it help remove P0420 code
Answer:	2 bottles of Lucas oil, one gas refill apart, helped with my P0420 Code on Infiniti QX60 engine light. With the 2nd bottle, the light was gone. It worked like a charm. I will continue to keep the fuel tank clean moving forward. Tip : don't wait for the fuel tank to be completely empty before you refill.

Product description

Lucas fuel treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected. 10003. It gives your fuel system what it really needs - a blend of super slick oils and additives with a high detergent action that allows the engine to operate at maximum efficiency. Also, it cleans and lubricates the carburetor and injectors and causes the fuel to burn more thoroughly for increased power and less fuel consumption. Lucas fuel treatment should definitely be used in vehicles that require leaded fuel because it actually replaces the benefits of lead in gasoline without causing harmful emissions. Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.

• Lucas fuel treatment is formulated for both gasoline and diesel engines, carbureted or fuel injected
• Use it to pass smog tests. Finally, it totally neutralizes the harmful effects of low sulfur diesel fuel.
• Tan color
• 1 Quart

User questions & answers

Question:	How often should i use this on my truck
Answer:	Every fill up
Question:	I have a bottle of the upper cylinder lubricant with injector cleaners and fuel conditioners, so is this only for gas or can it be added to the oil
Answer:	I would not advise it but instead look at the other Lucas products directly for use in your oil. I am happy with the fuel additive product.
Question:	Whats difference between this and the fuel treatment 5 oz
Answer:	I don't know of any difference to be honest., I've been using this in my gas tank for the past 12 years in our 27 year old car and it runs great! I use it monthly!
Question:	Does this product keep the fuel injector cleaned out and does it help keep the fuel filter cleaned out
Answer:	Claims it cleans the fuel injectors, been using for several years with no issues and it does help with performance.

Product features

Lucas Upper Cylinder Lubrication and Injector Cleaner

Lucas Upper Cylinder Lubrication and Injector Cleaner is recommended for both gasoline and diesel engines that work with either a carburetor or fuel injection system. A proprietary blend of oils and additives combine to clean the engine with high detergent action. You get a more efficiently running engine with increased power and less fuel consumption.

Working with people who keep lawns and landscapes beautiful

Stens works in partnership with professionals who make a living maintaining outdoor landscapes, so they understand the need of the industry.

Stens has been in the outdoor power equipment business since 1970, building a reputation for supplying parts that work as hard as you do.

The depth of Sten's inventory is extensive

The Stens product line represents replacement parts for more than 200 brands in the marketplace.

You'll find quality-made parts for virtually every make, model and type of outdoor power equipment.

Quality control assurance on every part

Choosing a quality Stens product is a wise decision because equipment downtime is costly to you in lost revenue.

Product description

Lucas Racing Break-In Oils help seal new rings while providing excellent extreme pressure properties that protect the entire valve train and of course, the camshaft. Especially designed for flat tappet camshafts, but can be used wherever you need the extra wear protection in the form of zinc. Formulated in three grades to cover all motors and applications



Recommended for use on initial break-in of both flat tappet and roller camshaft applications for maximum protection and performance. Excellent on track performance prior to switching engine over to the racing only line conventional or synthetic. Compatible with Ethanol, Methanol and high octane race gas.



Zinc levels typically at 3600 PPMS, which is much higher than commercial passenger car oils. Recommended for use in racing applications only. Not recommended for passenger cars requiring API service oil.

• Quicker more efficient ring seal
• Higher levels of zinc and phosphorus maximum protection
• A must use for flat tappet camshaft break-in
• Less blow-by equates more power and better ring seal
• Requires no moly supplement and no additional additives

User questions & answers

Question:	To everyone who has used this oil did yoh buy the sae 30w or the 20/50 breakin oil
Answer:	I ordered SAE 30 and received 20w-50
Question:	is this non-detergent oil ? better for seating piston rings
Answer:	Yes... this is a high-zinc break-in oil. Used for helping to seat the rings on an old school, flat-tappet engine. If you're running a full roller lifter set up, this may be a bit of preventative overkill, but it's cheap insurance. I run it for 500 miles then change to a oil designed for older hot rods (i.e.: contains zinc). Lucas also makes an excellent "Hot Rod & Classic" oil in 10w30 and 10w40 once you've broken things in. Note that these oils are NOT for modern engines and/or cars with catalytic-equipped emissions controls.
Question:	How long do you run this oil
Answer:	Called Lucus oil, they said for my Jeep L 4, at first start keep the RPMs up at med high for 5 minutes and don’t let up. Then run Jeep normally for 800 miles then change oil .
Question:	Will this work for a Diesel engine
Answer:	40w is more common for diesel engines.

Product description

Browse our exclusive collection of auto accessories that includes top quality products to enhance the style, comfort and functionality of your vehicle. We provide one stop shop for the perfect auto accessories for the vehicle.

• Virtually Eliminates Dry Starts And Excessive Wear
• Extends Oil And Engine Life
• Stabilizes Oil Pressure And Lowers Oil Temperature
• Eliminates Hesitation, Rough Idle, Stalling, And Poor Fuel Economy

User questions & answers

Question:	Is Lucas Oil 10131 Pure Synthetic Oil Stabilizer Low SAPS
Answer:	1 quart Lucas 4 quarts oil
Question:	Can Lucas 10131 be used with turbocharger? (4 cyl Saab
Answer:	it works with any automotive lubricants.
Question:	does using lucas oil pure synthetic oil stabilizer help with any start up rattle noise and or any knocking noise
Answer:	The mfr. States that it blends well with most oils,however, I believe the oils formulated for those type out drives are formulated to have a low affinity for water contamination. That is to say your oil could foam up from simple condensation in the gearbox while using the Lucas where it would likely not foam with the merc oil.
Question:	Can you use this as a fuel treatment too
Answer:	Its a 100% petroleum product.

Product description

Lucas engine oil Stop leak is an All new formulation of Lucas additives and very specific base stocks designed to Stop seal leaks in engines

• Product Type: Auto Oil
• Package Dimensions: 8.89 L X 10.16 W X 30.48 H (Centimeters)
• Package Weight: 0.953 Kilograms
• Country Of Origin: United States

User questions & answers

Question:	My 15K generac has a slow oil leak. How much product should I add to it
Answer:	You should use 20% of engines oil capacity
Question:	Can I use it on a gasoline engine
Answer:	yes
Question:	How much Lucas oil stop engine can I put in to the engine
Answer:	According to the label you put 20% of your engine capacity. (1 quart of Lucas oil to 4 quarts of engine oil).
Question:	I have a leak where my tranny meets my engine I believe it’s a “lower rear seal leak “ ? Will this be effective for that type of leak
Answer:	Depends on how damaged the seal is but this does work very effectively in most cases