13 best stop leak for radiators

Product description

Bar's Leaks Liquid Aluminum Stop Leak seals radiator leaks. Seals freeze plug leaks. Repairs gasket leaks and heater core leaks. Lowers water temperature.

• Bar's Leaks Liquid Aluminum Stop Leak seals radiator leaks. Seals freeze plug leaks. Repairs gasket leaks and heater core leaks. Lowers water temperature.
• Seals radiator leaks
• Seals freeze plug leaks
• Repairs gasket leaks
• Special Shipping Information: This item cannot be returned and has additional shipping restrictions

User questions & answers

Question:	Do I need to flush the cooling system before using this product if I had used bar’s tablet? I am choosing between these two since the leak is small
Answer:	You do not have to flush the system, in fact you may flush it after to put in the Bars Leak and run for a couple hundred miles to make sure your leak is sealed.
Question:	will this work on the head also
Answer:	Try it...it's inexpensive. Whether it works depends on the specifics of your problem. I tried it on a 4 cylinder BMW with a new head and profile gasket and a slow leak. It worked great.
Question:	can it be used in a Tahoe plastic tank
Answer:	i used it in my volvo which has a plastic expansion tank and no problems. it won't fix big leaks but if you're losing just a little coolant over time and can't find the leak this is the stuff to use!
Question:	My radiator leaking from the seam. Slightly overheating. Will this seal at the seam
Answer:	It should,depending on how big the leak/crack is,the one on my semi truck was dripping big,half a gallon a day,I was worried bc that s a $2,000.00 repair,I bought it not expecting any results,since I had previously used Bars leak (the small silver bottle) and didn t work,so this was a prayer and a last hope, 5,000 mls later and not a leak,not extra coolant added,it is liquid aluminum,so it bonds to wherever the leak is and forms a sealing coat...I think of it as welding from the inside...I hope it works for you as it did for me,it really was an answer to prayer...I know I m a bit dramatic but it was.PS,try to follow recommended amount or as close as recommended,not much less and not much more,I used 2 bottles on a 11 gal radiator.God bless.

Product features

Frequently Asked Questions

Yes, Liquid Aluminum is specifically designed to be directly added to the cooling system without having to flush out the antifreeze. It also can be used in water alone. But if using in water, it is recommended that another bottle of Liquid Aluminum be added to the system once antifreeze is installed.

Will it work in the new extended life antifreeze?

Yes, Liquid Aluminum works with all types of coolant including yellow, orange, pink, red, blue and green silicate based and non-silicate based OAT/HOAT antifreeze and/or water.

How long does it take to see results?

We recommend you drive/idle the vehicle for 10 to 20 minutes. In most cases the leak will be sealed instantly, but others will require up to 20 minutes. If the leak is not sealed in 20 minutes, a second application may be required or mechanical repair may be needed.

Bar’s Leaks is more than just a stop-leak company

We are a team of enthusiasts and experts who create memorable experiences with each and every one of our customers. With nearly 70 years of experience in helping everyday automobile owners repair leaks, we have the track record of success and long history that demonstrates our commitment and passion to helping drivers of all experience levels. You’ll see that our passion shines through in everything we do.

Product description

K-Seal 8 fluid ounce bottle is effective to 20 quarts cooling capacity. Just shake, pour and go. It repairs leaks and cracks in radiator, head gasket, heater core, freeze plugs, water pump casing, cylinder heads and engine blocks.

• REPAIRS IN MINUTES: Formulated to permanently weld radiators, including hard plastic aluminum heads and blocks in old and new cars. The only car radiator and gasket sealant university tested to meet ASTM D3147. Save time/money. US Bestseller
• SEALS CRACKS AND STOPS LEAKS: A DIY alternative to costly repairs, our coolant leak fix permanently seals cracks and holes! It quickly repairs your leaking radiator, freeze plug, heater core and water pump casing with no adverse impact on efficiency.
• POUR AND GO: Our cooling system sealer is easy to use: just shake the bottle, add to your radiator/overflow and run the engine! Unlike some traditional products, it mixes with all types of antifreeze, absolutely no draining or flushing required.
• SCIENTIFICALLY TESTED: Safe and effective, our cracked block repair can seal leaks up to 1/32 of an inch! Once cured, the repair withstands the high pressure of the combustion chamber, all without failing or clogging the cooling system.
• CUSTOMER SUPPORT: If K-Seal engine coolant leak stop doesn’t seal, the system might be over-pressurized. Check the Technical Specification section of this page for extra instructions for a successful repair. Over 8 million bottles sold worldwide!

User questions & answers

Question:	can you mix this with barstop if you all ready put that in the radiator
Answer:	I did mix this with Irontite All Weather Seal. Did the K-seal first. Irontite a week later. Just to be sure. Since they both said it can remain in the system. Two weeks, still good.
Question:	Can you use this in a 2013 escape
Answer:	Unless specifically told to use no heating system sealants I have no reason I can think of you can't use it. I used some but sparingly until it got the job done. Its a little bottle but still have half left. It's been okay for about 6 months now.
Question:	Does it discolor the antifreeze? Thanks
Answer:	Unfortunately I can't say. I have a GM vehicle that uses the orangish color engine coolant and it and this product are so close in color it's hard to say if it would discolor the usual green-colored coolant found in non-GM vehicles. The other challenge is that I can only look at the coolant through an overflow reservoir and it's so dark when I look inside (I have to use an LED flashlight to see it adequately) that it would be hard to tell if there was any discoloration.
Question:	will this work for leakey gaskets
Answer:	This is "liquid glass" that dries rock hard and will seal your head gasket leak (its been used in farm equipment for over 75 years and is WELL proven to work, and it was discovered over a hundred years ago), but you MUST perform a simple test. Start your vehicle, let it idle for 45 minutes straight. If the temperature gauge does not indicate that your engine is overheating, then this product will most likely work. No overheating at an idle for 45 minutes MEANS that the head gasket leak is still small enough to be filled by this liquid glass. Shake the container for 30 seconds, put the liquid in your COOLANT system, drive for an hour (or other words, operate at normal temperature, especially if its an aluminum block with cast iron heads), and then let it sit for 24-48 hours (the longest time is better). This sitting time allows the liquid glass to harden completely through. If it overheats then, it most likely its a thermostat or water pump or lower radiator hose sucking shut under load (sometimes the upper one also) or radiator or radiator fan or leaking core plug or leaking coolant storage unit OR your ENGINE OIL is very low from leaking (completely different problem that has nothing to do with the coolant system, but much to do with the cooling of the engine also) or heat indicator gauge or it still could be a blown head gasket, because the hole is just too big for the sealant to seal it up OR the head gasket BLOWS in another area after you have sealed up the first hole with the coolant sealant you added (that's why you should add it three times three different bottles of liquid glass over three months as I will mention below, that way, if it does blow in another area you will most likely SEAL that area also). But buy this and try it even if your vehicle fails the 45 minute test after 10 minutes. Sometimes, it will still seal the leak, or at least slow it down. Also, you can add this once a month for three months, and maybe that will work also (this gives you a month to see how the car performs under various conditions, and for the reason I just mentioned above). If you need the car to last for just a short while (month to six months) this can be a quick fix to hold you over until you can sell the car (under buyer be where conditions) or get it to the shop when you have the money. $15 and a few minutes of your time OR the mechanic, you have to decide. Good luck. I'm a retired mechanic with two degrees in Diesel mechanics and I ran a shop for a year.... :)

Product features

Permanent Coolant Leak Repair with K-Seal

Coolant leaks don’t have to result in costly repair bills – simply add K-Seal to your coolant system for a quick and permanent fix. K-Seal is trusted by millions of customers worldwide, and the only coolant leak repair fluid carried by the AA, the UK’s largest roadside repair company.

K-Seal couldn’t be simpler to use. K-Seal’s unique formula will seek out holes and cracks, and permanently seal them, with no adverse impact on the efficiency of your engine cooling.

Coolant System Sealer

Once the crack or hole has been located, the microfibers instantly begin to mesh together within the gap, building a seal literally fiber by fiber to stop the coolant leaking through the gap.

The particles in our K-Seal products are very precisely designed to be large enough to repair holes up to 0.635mm in size but deliberately small enough to never block any passageways or tubes within the cooling system, including those inside the heater core and radiator.

Once the microfibers have sealed and fixed the leak, a combination of exposure to either the external atmosphere or the gases within the combustion chamber and the heat within the cooling system and engine causes the K-Seal formula to cure. This results in an extremely strong and permanent seal able to withstand even the high pressures from the combustion chamber. This is how K-Seal Ultimate is able to repair head gasket failures, even where the cooling system is being over-pressurized exhaust gases entering the system

Common Coolant Leaks

K-Seal can deal with all of these leaks and more, as long as they are identified as early as possible. It is easy to use – simply shake it and pour it into the coolant mixture and it will work automatically.

Product description

Radiator Stop Leak, Granules, Size 0. 07 Oz, Dosage 0. 07 oz. , Specific Gravity Less than 1, Rust, For Use With Radiator/Coolant System Leaks

• JB WELD PERM O SEAL : Is a specially formulated non-toxic compound ground to a very fine particle size to quickly mix and flow into all areas of the cooling system to find and seal leaks.
• WHAT THE PROS USE: Mechanics, repair pros, and any avid DIYer knows our products bond strong to a variety of surfaces in even the toughest environments; and they have always been made in the USA.
• MONEY SAVING REPAIR SOLUTION: The powered concentrate allows for an economical repair as compared to liquid based alternatives that use similar technology.
• DURABLE FAST FIX: The special compound will quickly seal leaks and will also act as a rust inhibitor and lubricant to internal cooling system parts. It will not clog or harm your cooling system.
• DO IT YOURSELF: Big or small, you can DIY it with J-B. Our heavy duty adhesives repair & restore it right the first time. JB Weld delivers the legendary performance of the World's Strongest Bond.

User questions & answers

Question:	can you use this on indoor plumbing I have a pin hole in leak in copper pipe under the slab of my house
Answer:	I personally don't think it would work. Stop leak in a radiator has endless chances to stop the leak because the coolant-water continually recirculates. I don't think one flow by would be enough. I have had your problem. Trying to solder the pin hole is difficult if there is water in the pipe. I would clean around the hole with steel wool. I would force a small copper wire in the hole just about even with the hole to stop any flow of water. Then, I would solder over the wire.
Question:	how many one should I use ? I've tried 4 packs of a similar products and engine is still smoking
Answer:	Only 1 .... if you have used 4 others your leak is too large and with all that product in there you will need a professional coolant system flush and repair of leak
Question:	Does it work with plastic radiators small leak
Answer:	Not sure. Mine is metal.
Question:	Does it work for heater core leak
Answer:	I would have to say it depends on the size of the opening of the leak. If it is a very small leak, the perm-o-seal will work the same in the heater coil as the radiator. If you can't see the opening, then you will have to estimate by the amount of the leak. If it is rather slow, then for the price of perm-o-seal, it's worth a try.

Product description

Radiator leaks can be overwhelming, especially when you don’t have the time or the money to take your car to the shop. Many first discover these seal coolant leaks when they walk out to their car and notice a puddle sitting beneath it. The initial reaction is to assume that the leak will create an expensive visit to the garage, not to mention the inconvenience of going without your car during the repair. Well, it’s time to ease your worries, because we have created a fast and easy-to-use product that seals internal, external and coolant-to-oil leaks. Our Bar’s Leaks Pelletized Radiator Heavy Duty Stop Leak is specially formulated to seal larger leaks better than other stop leak products. You’ll find plenty of powder formula radiator stop leak products on the market, but you won’t find a seal coolant leak solution that beats ours in effectiveness. Our Pelletized Radiator Heavy Duty Stop Leak is versatile, too, working safely and effectively on plastic, aluminum and metal radiators, heater cores, gaskets and freeze plugs. It also has a water pump lube that lubricates water pump seals and inhibits the formation of rust and scale. Simply put, it’s the fast, effective, easy-to-use powder formula radiator stop leak that’s just as simple and straightforward for a regular driver as for an experienced mechanic. Convenient solutions to seal coolant leaks shouldn’t be limited to just those with advanced automotive knowledge, which is why each product in our catalog is designed to meet the needs of anyone who gets behind the wheel of a vehicle. In under an hour, you can quickly and easily solve that once-dreaded leaky radiator. Give it a try and get your car back on the road in no time.

• Seals leaks
• Conditions cooling system
• Inhibits rust and corrosion
• Lubricates water pump seals
• Helps control electrolysis

User questions & answers

Question:	What are the beads inside for? Can they be poured into the radiator
Answer:	The beads break down in the system and contain most of whats in the product to seal . ..... So yes, please pour the entire container into the vehicle. Great question... Thank you Eric
Question:	mi radiador no tiene tapa,puedo echar el sellador en el tanque de reserva
Answer:	Si!
Question:	My car does not have a cap on the top of the radiator as the coolant gets added through the overflow. How would I add this to my car
Answer:	Thank you for your question, and for considering Bar's Leaks to help with a cooling system leak. The product you are asking about - Bar's Leaks Heavy Duty Radiator Stop Leak (part number PLT11) - is designed to be installed directly into the radiator. If you don't have access to the radiator through a radiator cap, you can remove the top hose where it attaches to the radiator and install the product in through the hose. Be sure to shake the product well before installing. If installing this way is not an option for you, we would suggest you consider our Radiator Stop Leak Tablets (part number HDC) instead. These pellets can be crumbled up and installed in the overflow reservoir, as long as it is pressurized. Please note: Cooling systems that are dirty or partially clogged should be flushed before using any cooling system stop leak products. If you have any other questions or would like additional information, please feel free to call our Tech Support team at 1-800-345-6572. We are here to assist you Monday through Friday, from 8 am to 5 pm, Eastern time.
Question:	does 2001 ford crown vic come from factory with stop leak in coolent
Answer:	I don't know. But I used this on my 2006 Ford Explorer 4.6L V-8 and it was useless. I had a very small leak in the radiator and after using this stop leak, the hole blew open a week later and all the radiator fluid came pouring out.

Product description

It’s part of life: older cars, trucks, vans, SUVs and even RVs can develop larger leaks in their radiators and intake manifolds. If you’ve tried regular stop leak products, you know they are not powerful enough to stop these larger leaks. If you visit the service center down the street, you know just how expensive it can be to repair an intake gasket leak through a mechanic. Isn’t there a better way? There should be, which is why Bar’s Leaks designed the Liquid Copper Block Seal Intake & Radiator Stop Leak. This one-step sealer was designed to quickly and safely stop these overwhelming leaks. When you’re experiencing a mild to moderate intake gasket seal leak, discover the fast, effective, inexpensive power of liquid copper. What does it do? Our formula permanently repairs larger leaks in radiators, intake manifolds and gaskets, heater cores, blocks, heads and freeze plugs. It contains an antifreeze-compatible sodium silicate liquid glass formula, so no draining of the cooling system is required. Not to mention, it will not harm the cooling system when used properly. The intake gasket seal you’ve been looking for is far more effective, easy to use, and less expensive than you’ve ever imagined. This is why Bar’s Leaks exists: To offer imminently usable, low-cost intake gasket seal and other products to auto owners who have no special experience or expertise. You’ll find plenty of options when searching for products to fix an intake gasket leak. While our competition may claim to stop the leak quickly, their products don’t always perform as advertised and they sometimes make things worse. Their stop leak products can’t get your car back on the road like Bar’s Leaks — that’s why we’ve been the most trusted stop leak brand since 1947. Throughout our long history of serving car owners like you, we’ve used a team of dedicated chemical engineers to constantly develop and refine products that are safe, fast and effective in stopping intake gasket leaks and other automotive problems — including liquid copper and much more. Make sure to watch Bobby and Caitlin in our handy how-to video so you can become a “three-minute mechanic” and finally take control of that leak.

• Seals larger leaks seals
• Repairs heater core leaks
• Repairs freeze plug leaks
• Repairs blown head gaskets
• Repairs blocks

User questions & answers

Question:	Can i use this product to stop leak on my honda element 2003 engine block? the engine block has a small leak
Answer:	Thank you for your question and for considering Bar's Leaks Liquid Copper Block Seal Intake & Radiator Stop Leak (part number 1109). This one step formula was developed to repair larger leaks in radiators, intake manifolds & gaskets, heater cores, blocks, heads and freeze plugs, so it should help you with a small leak in your Honda Element. Please note, though, that cooling systems that are dirty or partially clogged should be flushed before using. If you haven't had a chemical cooling system flush performed on your vehicle in the last four years, you might consider doing so now. Flushing with water will remove any loose sediment in the cooling system, but if there is any scale built up, it would take a chemical flush to dissolve and remove it, giving our product the best possible chance to stop the leak. If you have any questions, or we can be of further assistance, please feel free to contact our Tech Support team at 1-800-345-6572. We are here to assist you Monday through Friday, from 8 am to 5 pm, Eastern time.
Question:	Can this help with a 5.3l gm engine with the bad cylinder head castings? i'm saving for a replacement engine, just need this one to last a while
Answer:	Thanks for your question, and for considering Bar's Leaks to help with your vehicle's needs. The product you are asking about - Bar's Leaks Block Seal Intake & Radiator Stop Leak is a great product for repairing larger leaks in radiators, intake manifolds & gaskets, heater cores, blocks, heads and freeze plugs. However, if your vehicle is showing signs of head gasket failure due to the bad castings you refer to, we would suggest one of our head gasket products, such as Head Gasket Fix (part number 1111), which is very successful in sealing leaks as long as your vehicle can run 20 minutes or longer without overheating or needing to add coolant. If your vehicle is unable to run for 20 minutes without overheating, but can run for at least 15 minutes, we recommend our strongest head gasket stop leak - Head Seal Blown Head Gasket Repair (part number HG-1). For best results, these products should be installed into a clean cooling system, following the installation instructions and proper dosage. If you are unsure how clean your cooling system is, or you haven't had it chemically flushed in the last three to four years, we recommend doing so before installing any stop leak products. If you have any other questions, or we can be of further assistance, please feel free to call our Tech Support team at 1-800-345-6572. We are here to assist you Monday through Friday, from 8 am to 5 pm, Eastern time.
Question:	heater core leak fixed
Answer:	The label on the lower right does show Heater Core. So this could work since coolant is being pumped through the heater core to heat the cabin of a vehicle.
Question:	Will this help to stop a block leak where the water pump connects to the cooling system
Answer:	No. This will only help with small leaks. As temp fix.

Product features

Frequently Asked Questions

Yes, unlike other copper stop leak products, Liquid Copper One Step sealer contains an antifreeze compatible sodium silicate formula, so draining of the cooling system is not required as long as manufactures recommendations are followed. It also can be used in water alone however, a second bottle of Liquid Copper is recommended to be added to the system once antifreeze is installed.

Do I need to drain my cooling system after using Liquid Copper?

No, this product is designed to be left in the cooling system to protect from future leaks.

What are the dosage recommendations?

Use 1 (one) bottle for regular size cooling systems, this covers most 4, 6, 8 and 10 cylinder engines. For small cooling systems, such as 4 cylinders with no air conditioning, use 1⁄2 (half) of bottle. For other small systems use approximately 3 ounces per gallon of cooling capacity. In larger systems, use 1 (one) bottle for every 6 gallons of cooling system capacity.

About Bar's Leaks

Bar’s Leaks is more than just a stop-leak company. We are a team of enthusiasts and experts who create memorable experiences with each and every one of our customers. With nearly 70 years of experience in helping everyday automobile owners repair leaks, we have the track record of success and long history that demonstrates our commitment and passion to helping drivers of all experience levels. You’ll see that our passion shines through in everything we do.

Each individual Bar’s Leaks product is formulated and manufactured right here in the U.S.A. We’re committed to creating fast and affordable products that fit perfectly into your lifestyle and budget. Choose Bar’s Leaks, so you can discover just how simple automotive maintenance can be when you have the right tools.

User questions & answers

Question:	What are the Instructions?! It only says easy to use
Answer:	The instructions are online

Product description

K-Seal 8 fluid ounce bottle is effective to 20 quarts cooling capacity. Just shake, pour and go. It repairs leaks and cracks in radiator, head gasket, heater core, freeze plugs, water pump casing, cylinder heads and engine blocks. For truck, tractor, industrial, RV and large capacity engines.

• REPAIRS IN MINUTES: Create a permanent weld within the entire coolant system, including on hard plastic radiators and aluminum heads and blocks in larger capacity engines, AG, RV etc. The only industrial coolant sealant university tested to meet ASTM D3147.
• SEALS CRACKS AND STOPS LEAKS: Avoid expensive downtime, our coolant stop leak will permanently seal cracks and holes! Quickly repair your head gasket, block, leaking radiator, freeze plug, heater core & water pump casing with no adverse impact on efficiency.
• POUR AND GO: Our cooling system sealer is easy to use just shake the bottle, add to your radiator/overflow and run the engine! Unlike some competitive products, it mixes with all types of antifreeze, no draining, flushing or pulling the thermostat required.
• SCIENTIFICALLY TESTED: Safe and effective, our Heavy Duty Coolant stop leak repair seals leaks up to 1/32 of an inch! Once cured, it withstands the high pressure of the combustion chamber, without failing or clogging the cooling system. US Bestseller
• CUSTOMER SUPPORT: If our engine coolant leak doesn’t seal your head gasket, the system might be over-pressurized. Check the Technical Specification section of this page for extra instructions for a successful repair. Over 8 million bottles sold. Save time/money

User questions & answers

Question:	Tried using alumaseal, which isn't working. will i need to flush the system before using the k-seal
Answer:	I used the HD Truck bottle on my 1998 GEO Tracker ( used 1/3 of the bottle ) of K-Seal and it worked. I have used so many to no avail. To answer your question, I must have @ least 3 to 4 other sealers in my colling system when I added K-Seal. It's been almost a year & no adverse effects having not flushed my radiator. Should I have flushed the radiator & the system? Yes, I should have.
Question:	Will this work with aluminum heads
Answer:	It works equally well with cast iron or aluminum. Great Stuff. Not a long-term solution, but it will buy you a lot of time.
Question:	how much do i need to pour in a diesel 1 ton cummins
Answer:	You need this one bottle for a Dodge 3500 hd. I have this one bottle in my HD Freightliner 330hp MBZ engine hauling freight (54,000 lbs cap) 6 days a week and it stopped my coolant leak in the engine bay and heater core with no blockage and no. My opinion, Many reviews say products dont work BECAUSE most people dont take care of their equipment and their vehicles are old, high mileage and no maintenance done. None of the add to a tank products are as good as replacing with new parts but thats expensive, we get it. This may or may not fix your problem but its a low cost gamble with a high probability of success. Dont listen to the negative reviews. If the problem comes back, your damage was too far gone and in need of replacement anyway.
Question:	Does it work on potentially warped heads
Answer:	Probably not, but read on, and learn about all coolant leak problems if you want and how effective this product is....This bottle is enough for up to 12 cylinder engines.This will work for any type of coolant leak, if the leak is small. This will work on head gasket leaks also, read this 3 minute read on what to do if its a head gasket leak. Also, for for your information - This is "liquid glass" that dries rock hard and will seal your head gasket leak (its been used in farm equipment for over 75 years and is WELL proven to work, and it was discovered over a hundred years ago), but you MUST perform a simple test. Okay, start your vehicle, let it idle for 45 minutes straight. If the temperature gauge does not indicate that your engine is overheating, then this product will most likely work. No overheating at an idle for 45 minutes MEANS that the head gasket leak is still small enough to be filled by this liquid glass. Shake the container for 30 seconds, put the liquid in your COOLANT system, drive for an hour (or other words, operate at normal temperature, especially if its an aluminum block with cast iron heads), and then let it sit for 24-48 hours (the longest time is better). This sitting time allows the liquid glass to harden completely through. If it overheats then, it most likely its a thermostat or water pump or heater core or lower radiator hose sucking shut under load (sometimes the upper one also) or radiator or radiator fan or leaking core plug or leaking coolant storage unit OR your ENGINE OIL is very low from leaking (completely different problem that has nothing to do with the coolant system, but much to do with the cooling of the engine also) or heat indicator gauge or it still could be a blown head gasket, because the hole is just too big for the sealant to seal it up OR the head gasket BLOWS in another area after you have sealed up the first hole with the coolant sealant you added (that's why you should add it three times three different bottles of liquid glass over three months as I will mention below, that way, if it does blow in another area you will most likely SEAL that area also). But buy this and try it even if your vehicle fails the 45 minute test after 10 minutes. Sometimes, it will still seal the leak, or at least slow it down. Also, you can add this once a month for three months, and maybe that will work also (this gives you a month to see how the car performs under various conditions, and for the reason I just mentioned above). If you need the car to last for just a short while (month to six months) this can be a quick fix to hold you over until you can sell the car (under buyer be where conditions) or get it to the shop when you have the money. $15 and a few minutes of your time OR the mechanic, you have to decide. Good luck. I'm a retired mechanic with two degrees in Diesel mechanics and I ran a shop for a year.... :)

Product features

Permanent Coolant Leak Repair with K-Seal

Coolant leaks don’t have to result in costly repair bills – simply add K-Seal to your coolant system for a quick and permanent fix. K-Seal is trusted by millions of customers worldwide, and the only coolant leak repair fluid carried by the AA, the UK’s largest roadside repair company.

K-Seal’s unique formula will seek out holes and cracks, and permanently seal them, with no adverse impact on the efficiency of your engine cooling.

Coolant System Sealer

Once the crack or hole has been located, the microfibers instantly begin to mesh together within the gap, building a seal literally fiber by fiber to stop the coolant leaking through the gap.

The particles in our K-Seal products are very precisely designed to be large enough to repair holes up to 0.635mm in size but deliberately small enough to never block any passageways or tubes within the cooling system, including those inside the heater core and radiator.

Once the microfibers have sealed and fixed the leak, a combination of exposure to either the external atmosphere or the gases within the combustion chamber and the heat within the cooling system and engine causes the K-Seal formula to cure. This results in an extremely strong and permanent seal able to withstand even the high pressures from the combustion chamber. K-Seal Ultimate is able to repair head gasket failures, even where the cooling system is being over-pressurised by exhaust gases entering the system.

Common Coolant Leaks

K-Seal can deal with all of these leaks and more, as long as they are identified as early as possible. It is easy to use – simply shake it and pour it into the coolant mixture and it will work automatically.

Product description

K-Seal ULTIMATE is the simple, permanent fix for blown head gaskets, cracked heads and blocks, and porous engine blocks. Our unique formula works with all water-cooled engines – there’s no need to drain or flush your cooling system, and it doesn’t matter what kind of antifreeze or coolant you’ve used previously. Simply shake the bottle, pour K-Seal ULTIMATE into your cooling system, and you’re back on the road. Just one bottle of K-Seal ULTIMATE is enough to fix blown head gaskets and cracked heads in cars, SUVs and small trucks. For larger engines, simply use two bottles.

• REPAIRS IN MINUTES: Permanently fix blown head gaskets, cracked heads and cracked/porous blocks including aluminum heads in old and new cars. The only head gasket and block sealant that is 3rd party tested to meet ASTM D3147. Save time/money
• SEALS CRACKS AND STOPS LEAKS: A DIY alternative to costly repairs, our head gasket fix permanently seals cracks and holes! Quickly repair your blocks, leaking radiator, freeze plug, heater core and water pump casing with no adverse impact on efficiency.
• POUR AND GO: Our head gasket sealer is easy to use just shake, add to your radiator/overflow and run the engine! Unlike some competitive products, it mixes with all types of antifreeze, absolutely no draining, flushing or pulling the thermostat required.
• SCIENTIFICALLY TESTED: Safe, effective, our head gasket and block repair seals leaks up to 1/32 of an inch! Once cured, the repair withstands the high pressure of the combustion chamber, all without failing or clogging the cooling system. US Bestseller
• CUSTOMER SUPPORT: If our head gasket repair leak doesn’t seal your intake gasket, the system might be over-pressurized. Check the Technical Specification section of this page for extra instructions for a successful repair. Over 8 million bottles sold.

User questions & answers

Question:	what if car won't start
Answer:	Has to recirculate through the cooling system. Car has to be running. I can't see any other way around that.
Question:	Does it use Sodium Silicate
Answer:	Nowhere on the bottle does it say sodium silicate.
Question:	Is this any different from the smaller pour and go? I have already put that in the engine. If it does not work, can I add this
Answer:	I use this in antifreeze for a head leak Did work for some tine
Question:	Is it okay to continue to idle the car with engine and brake lights on with liquid coming out of radiator? It says to idle for 20 minutes
Answer:	The system should be sealed as the product circulates though it for the 20 minutes.

Product features

Permanent Coolant Leak Repair with K-Seal

Coolant leaks don’t have to result in costly repair bills – simply add K-Seal to your coolant system for a quick and permanent fix. K-Seal is scientifically tested, trusted by millions of customers worldwide, and the only coolant leak repair fluid carried by the AA, the UK’s largest roadside repair company.

K-Seal couldn’t be simpler to use. K-Seal’s unique formula will seek out holes and cracks, and permanently seal them, with no adverse impact on the efficiency of your engine cooling.

No Need for Expensive Head Gasket Repairs

K-Seal ULTIMATE K3501 Head Gasket Repair is the simple, permanent fix for blown head gaskets, cracked heads and blocks, and porous engine blocks.

Our unique formula works with all water-cooled engines – there’s no need to drain or flush your cooling system, and it doesn’t matter what kind of antifreeze or coolant you’ve used previously. Simply shake the bottle, pour K-Seal ULTIMATE into your cooling system, and you’re back on the road.

Common Coolant Leaks

K-Seal can deal with all of these leaks and more, as long as they are identified as early as possible. It is easy to use – simply shake it and pour it into the coolant mixture and it will work automatically.

Product description

Rescue Tape is a self-fusing silicone repair product with infinite uses. First used by the U.S. Military and now seen at consumer and industrial trade shows across America, this is the most versatile and easy-to-use emergency repair product available. Incredible 950 PSI tensile strength. Insulates 8,000 volts per layer. Withstands 500°F of heat and remains flexible to -85°F (-60°C). Creates a permanent, airtight and watertight seal in seconds! Resists fuels, oils, acids, solvents, salt water, road salt and UV rays. Never gets gummy or sticky like electrical or duct tape - No messy cleanup! Has an unbelievably long shelf life! Works great for: emergency hose repair, pipe and plumbing repair, electrical insulation, corrosion protection, sealing connections, marking lines and chain, rigging applications, wiring harnesses, waterproofing, whipping rope ends, tool handles and grips, emergency O-rings and much, much more! Rescue Tape is the Ultimate Multi-Purpose Self-Fusing Repair Tape! Stretch, Wrap & Get Rescued. Each roll measures 1" wide x 12' long x 20mil. Hang packaged.

• Creates A Permanent Airtight, Watertight Seal In Seconds, Repair & Seal Leaky Hoses, Pipes, Tubing, Lines, & Fittings, Works Even Over Oily Or Dirty Surfaces
• Highly Durable Product
• Manufactured In United States
• Material Name:Synthetic

User questions & answers

Question:	Work on AC pipe on car
Answer:	I never tried that, but considering the cost of a new pipe compared to the tape, try the tape. The only problem I foresee is the pressure on the pipe, but I use it on my pool and there is a lot of pressure going through those pipes.
Question:	Will this work on a dripping metal pipe
Answer:	It did not work for me on plastic pipe, I doubt it would work on metal. My opinion it is a waste of money.
Question:	Will this be able to seal a hole in a garden hose
Answer:	If you follow the directions, yes.....the tape does not seal to the hose it seals to itself....so you have to stretch and wrap, stretch and wrap, overlapping as you go.
Question:	Will this stick to fabric
Answer:	I doubt this will stick to fabric; and for that matter it does not stick to anything. The way it works is that it sticks/bonds to itself so it has to be wrapped around the piece you are repairing, i.e pipe leak, insulating wire, sir line, etc.

Product description

Finally, the market leader in stop leaks offers the best hydraulic stop leak and conditioner product on the market, for any price. Available in 32 oz, 1 gallon, 5 gallon and 55 gallon sizes, this professional-grade formula excels at Repairing hydraulic fluid leaks, reducing friction and wear in hydraulic systems, extending fluid & system life and renewing hydraulic seals & O-rings. If you are dealing with a hydraulic fluid leak, you’re in the right place. Bar’s Leaks Hydraulic Seal is safe to use with 22, 32, 46, 68 and all other petroleum and synthetic hydraulic fluids. Perfect for construction, farm, manufacturing, forestry, mining and marine machinery. See the Overview below for more information.

• Specially designed to repair hydraulic fluid leaks, reduce friction/wear and renew seals and O-rings in hydraulic systems
• Engineered to be professional-grade and is safe to use for consumer applications as well as commercial use cases
• Works with all petroleum and synthetic fluids, pump seals, control valve seals, actuators, rams, cylinders, O-ring boss fittings and hydrostatic transmissions
• Keeps hydraulic seals soft and pliable, reduces friction and wear in hydraulic systems, cleans and prevents formation of sludge and varnish, and helps hydraulic systems run cool and last longer
• Made in the USA

User questions & answers

Question:	How much do you add in new holland tractor t
Answer:	Thanks for your question and for considering Bar's Leaks Hydraulic Seal Stop Leak and Conditioner (part number H60) to help with your tractor's needs. The dosage for this product depends on the hydraulic fluid capacity, and can vary depending on if you are using it as a preventative, using it as a stop leak (normal use), or for extremely worn systems. Please see below for the dosage recommendations: DOSAGE: Preventative - for preventative maintenance, use one-half (1/2) ounce of Bar's Leaks Hydraulic Seal per quart of hydraulic fluid capacity. Normal - add one (1) ounce for every quart of fluid capacity Worn - use up to two (2) ounces per quart of fluid capacity If you have any other questions or we may be of further assistance, please feel free to call our Tech Support team at 1-800-345-6572. We are here to assist you Monday through Friday, from 8 am to 5 pm, Eastern time.
Question:	Does it work for brakes
Answer:	No.. According to the manufacturer this is not for use in braking systems......
Question:	I have a diesel Toyota forklift 8k & main ram is leaking pretty bad where it extends. There are no gouges or scratches. Will this help
Answer:	I have a 1951 Farmall m with a dual loader and so far it seems to have helped with my leaks.
Question:	Compatible con Audi A
Answer:	Thank you for your question and for considering Bar's Leaks Hydraulic Seal to help with your 2005 Audi A6. This product would be compatible with any system in your vehicle that uses hydraulic petroleum and synthetic fluids. It is NOT to be used in DOT 3, 4, or 5 hydraulic brake systems. For more information on this product, or if you have any further questions, please contact our Tech Support team at 1-800-345-6572. We are here to assist you Monday through Friday, from 8 am to 5 pm, Eastern time.

Product description

If the words “blown head gasket” make you nervous, we’re right there with you. We know firsthand that fixing a blown head gasket requires a hefty chunk of change and a few days without your car. Who has time to spend taking their car to the shop for a blown head gasket? And who has the extra cash to pay for a blown head gasket without planning for it? No, visiting the shop for a blown head gasket fix isn’t ideal. But what if we told you it was possible to fix this yourself with one of the most reliable blown head gasket solutions on the planet? Our easy-to-use Bar’s Leaks Head Gasket Fix will not only save you all that cash, but also get you back on the road in less than an hour. At Bar’s Leaks, we specialize in creating chemical repair solutions that are fast, easy, effective and affordable. Rather than spending hundreds or thousands of dollars at the repair shop, you spend just a few dollars and all without any of the inconvenience. This product contains a combination of antifreeze-compatible sodium silicate sealing liquid and various gasket-sealing particles that penetrate gaps and cracks and harden to permanently stop leaks. It’s liquid technology for damaged, leaking or blown head gaskets, and with over two million bottles sold, you can count on it to perform. We have a team of top-flight chemical engineers who are always innovating and pursuing ways to improve our existing products. As auto manufacturers introduce new technologies, we offer new products that will help everyday drivers save time and money through fast and effective solutions. Using our head gasket repair liquid is easy. Simply follow along with Bobby and Caitlin in our how-to video to safely and quickly get your car back on the road. There’s no reason a blown head gasket should sideline your life.

• Stops block leaks
• Seals cracked cylinder heads and blocks
• Repairs blown head gaskets
• Contains a combination of antifreeze compatible sodium silicate sealing liquid and various size gasket sealing particles which penetrate gaps & cracks and harden to permanently stop leaks.

User questions & answers

Question:	can i use it when the copper stuff failed to work
Answer:	What I did was dump a can of the head gasket fix, _and_ a can of the copper stuff into the radiator. I think they're pretty much the same, except the head gasket stuff has bigger particles. My reasoning was that I have no idea what the leak(s?) look like, and multiple particle sizes were better than not. At any rate - one can of each into my 1999 Ranger 3.0 appears to have stopped a leak that was occurring between the timing cover and the block. On that engine, the timing cover has ports for the water pump, and taking off the timing cover.... pulley, A/C components, P/S components, water pump, and alternator, as well as the radiator. A real pain in winky. I figured before all that work... lets give 'er a try with Bar's. So far so good!
Question:	Can thsi item ship to malaysia
Answer:	You may try putting it in your shipping cart. if it shows a warning sign about the shipping problem then it won't be shipped there.
Question:	Can this seal leak from pistons to coolant system, rather than vice-versa? My car doesn't burn coolant, rather the exhaust goes into coolant system
Answer:	Yes. A bad head gasket can cause water to get into the oil (very very bad), water into the combustion chamber (white clouds from the exhaust pipes) and other less than desirable things. The leak seal product is a stop-gap measure not a long term fix. The head gasket needs to be changed.
Question:	If my car continues to emit white smoke from exhaust, should i switch to HG-1 instead
Answer:	Typically, the seal is formed during the recommended idle time shown in the instructions, but if the leak is more severe or harder to get to, it could take several thermal cycles (heating up and cooling down) before the leak is fully sealed. In addition to watching for the white smoke to go away, our recommendation is to continue to monitor the engine temperature and coolant level over the next couple of days to see if the vehicle is overheating, and also to note how much coolant you are adding, as well as how often you are adding it. If the leak is not sealed, and you wish to use HG-1, you certainly could do so, but we would recommend that you drain and flush the cooling system before you do so in order to prevent the formation of a flow restriction from having too much stop leak product in your vehicle's coolant at one time.If you have any additional questions, or need additional information, please call our Tech Support team at 1-800-345-6572. We are available to help you Monday through Friday, from 8 am to 5 pm Eastern time.

Product features

Blown Head Gasket?

When you think about a blown head gasket, do you see your money being spent at the repair shop? How much time and inconvenience is involved in taking your car to a mechanic for blown head gasket repair? The lost time is a frustration, and the money it takes to alleviate a head gasket leak is overwhelming. That’s because fixing a head gasket can cost you quite a bit (typically $1,500-$3,000). We know you would rather spend that money on the things that matter most. That’s why we created professional-grade, easy-to-use head gasket solutions. It’ll repair your leaking head gasket and save you money.

Bar’s Leaks recommends asking a few questions to narrow the field.

Bar’s Leaks is more than just a stop-leak company

We are a team of enthusiasts and experts who create memorable experiences with each and every one of our customers. With nearly 70 years of experience in helping everyday automobile owners repair leaks, we have the track record of success and long history that demonstrates our commitment and passion to helping drivers of all experience levels. You’ll see that our passion shines through in everything we do.

Each individual Bar’s Leaks product is formulated and manufactured right here in the U.S.A. We’re committed to creating fast and affordable products that fit perfectly into your lifestyle and budget. Choose Bar’s Leaks, so you can discover just how simple automotive maintenance can be when you have the right tools.

Bar’s Leaks. The fastest, safest way to get your show back on the road. Guaranteed.

Product description

Ever wish you had double the time or money? Or both? We know we do. That’s why we created the Bar’s Leaks Radiator Stop Leak 2X Concentrate. It has double the power of most other stop leak products and saves you double the time and money that it would take to get your car to the repair shop. When you need to fix a radiator leak, you don’t want to spend the time it will take to visit a mechanic. And then there’s the cost of getting a radiator stop leak solution. But getting the fix radiator leak solution you need shouldn’t be time consuming and it shouldn’t be expensive. That’s why, at Bar’s Leaks, we’ve developed our line of radiator top leak products, including our 2X Concentrate. Bar’s Leaks Radiator Stop Leak 2X Concentrate Sealer is specially designed to stop minor to moderate cooling system leaks and drips caused by normal cooling system wear and age. It works with ALL types and colors of antifreeze coolant and/or water. Which is one of our commitments to customers like you: No matter what product you choose, our radiator stop leak or something else entirely, you can also count on effectiveness and ease-of-use. There’s no special automotive expertise needed to fix a radiator leak with Bar’s Leaks. Simply watch Bobby and Caitlin in our how-to video, and they will show you how easy it is to install this product.

• Product type :AUTO ACCESSORY
• Package dimensions :4.064 cm L x6.096 cm W x12.446 cm H
• country of origin :United States
• package weight :0.81lbs

User questions & answers

Question:	Do you have to drain the radiator first
Answer:	Good afternoon. Thank you for your question and for considering Bar's Leaks to help with your automotive needs. The product you are asking about- Bar's Leaks Radiator Stop Leak 2x Concentrate (part number 1194) - is designed to be added to the coolant or water already in your radiator. If the coolant level is low, just add the product to the cool radiator and then fill the radiator and overflow tank to the proper level. NOTE: cooling systems that are dirty or partially clogged should be flushed before using. If you haven't done so in the last three to four years, we recommend you run a chemical cooling system flush product through the cooling system. This will help dissolve any scale or buildup inside the system and help prevent any potential flow restrictions. If you have any other questions, or would like additional information on this or any of our products, please call our Tech Support team at 1-800-345-6572. We are here to assist you Monday through Friday, from 8 am to 5 pm Eastern time.
Question:	My car is leaking antifreeze a lot will this help stop it ? Also if it is do I put this in my antifreeze thing ? Or radiator
Answer:	This is at best a temporary fix. If your car is leaking a lot best to see a mechanic and have it repaired. This product does work but is best for small leaks. Use in your radiator.
Question:	Dose this work on a over pressured coolant system, the radiator hoses are some time rock hard some times soft? No coolant lose
Answer:	If you are not losing coolant you don't need a sealer.
Question:	Can you use this product on a motorcycle
Answer:	Thank you for your question, and for considering Bar's Leaks for your motorcycle needs. Yes, this product can be used on a motorcycle, but you will need to adjust the dosage accordingly, as this bottle is designed to treat three gallons of coolant. The recommended dosage is 2 ounces of Radiator Stop Leak for each gallon of coolant capacity. If you have any additional questions or need further assistance, please feel free to contact our Technical Support team at 1-800-345-6572. We are available to help you Monday through Friday, from 8 am to 5 pm Eastern time.

Product description

Plastic Tank & Radiator Repair Kit. Works on Plastic Tanks & Metal Surfaces. Stops Leaks. No Removal Required.

• RADIATORWELD: Our radiator and plastic tank repair kit has all you need for making professional quality, permanent repairs with state of the art components and easy to follow instructions.
• COUNT ON US: For more than 40 years, our products have earned a loyal following from people who take pride in their work. With each product we innovate, we continue to provide the world's strongest bond for your projects.
• SIMPLE TO USE: No removal of tank or radiator is required to stop leaks. Easily fix holes up to 3/8" diam. or cracks up to 4" long. Includes epoxy putty, fiberglass cloth, sandpaper, and applicator.
• VERSATILE & DEPENDABLE: Great for radiators, washer fluid tanks, storage tanks, water tanks, plastics, composites, PVC and more. Professionals, mechanics and avid DIYers know J-B gets the job done.
• NO PROJECT TOO BIG OR TOO SMALL: We have all the products you need to get the job done right. JB Weld always delivers the legendary performance of the World's Strongest Bond.

User questions & answers

Question:	will this item cure in cold temps
Answer:	Didn't work for me in warm temperatures .
Question:	Would this repair a clean break on plastic neck ? Top of neck ( with radiator cap ) broke off cleanly
Answer:	I honestly don't believe it would, pressure from radiator would probably just cause rebreak. It held a crack in my radiator for short time til I could get a new radiator and my mechanic just peeled the weld off in front of me.
Question:	I have a leak on a small stem (i think is aluminum) at the seam that holds a small rubber hose that antifreeze runs though, the small stem gets hot
Answer:	My honest opinion is this isn't going to work for your issue.... I used this on my plastic radiator at the top in small crack. It worked for couple weeks and had to buy new radiator... don't waste your money
Question:	Does j-b weld 2120 really work on radiatots
Answer:	It does if you work fast with it.