12 best epoxy resin glue

Product description

Gorilla takes epoxy to a new level—the Gorilla tough level. With its superior solvent and water resistance, Gorilla epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it Dries in an ideal, crystal-clear finish that makes projects look spotless. Directions: 1. Prepare your work area and the surface: It is recommended to use Gorilla epoxy In a well-ventilated area. Prepare the surface: to improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. 2. Mixing Gorilla epoxy: remove the black cap. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip. Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. Mix the two parts for about 20 seconds, until the mixture is uniform. 3. Application: after mixing is complete, apply Gorilla epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply. 4. Clamping: to reach maximum bond strength, clamp project together and leave undisturbed. Important cure times: set: 5 minutes to apply and position handling: allow to cure for 30 minutes undisturbed (no weight or handling) final cure: allow 24 hours for load-bearing weight storage: to close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly. Click on the Gorilla link at the top of this page to see more fine products from the Gorilla glue company.

• Strong, permanent, fast and gap-filling; great for multiple surface applications
• Best for tough repairs requiring a durable bond, gap-filling and solvent resistance
• Dries clear; ideal for clean, easy finishing
• 6 minute set; plenty of repositioning time for the perfect fit
• Easy-to-use syringe; separate barrels of resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses

User questions & answers

Question:	Will Gorilla glue work on hanging something on ceramic tile
Answer:	I have zero doubt that it will work. I would prep the surface of the tile with sandpaper or steel wool at the least.
Question:	Will this work to fix an axe head
Answer:	I used this to fix a maul head to the handle. It was slipping thru extended use and looked like it would come off soon. First sanded and cleaned the fiberglass handle with acetone to created a rough and clean surface. Then wiped the inside of the mall head with acetone. Mixed up a big batch since I didn't want to fall short of product once I started filling. Applied it liberally to the handle then slipped the head on and used the rest to fill in around any crevice left around the head until it was one pool of epoxy flush with the head top. Let it sit for a day then used. Been over a year and it has not had any sign of slipping and looks the same as when I first glued it on.
Question:	I need a clear epoxy to cover and protect a circuit i made in a small box mod i made. its for a small 4- 6 volt device. is this ok
Answer:	Probably YES is your answer with NO guarantees, since I have never used an epoxy to cover ANY type of circuits. I HAVE HOWEVER, used a SILICONE SEALANT (marine grade) also available through AMAZON, to cover AND seal electrical circuits on several watercraft I have owned over the years. ALL with great success. The beauty of the silicone is that it dries clear and can easily be removed while the epoxy dries to an amber hue and is almost impossible to remove. Once it dries, it's there forever. MY suggestion is use a marine grade (waterproof) silicone sealant. GOOD LUCK!
Question:	I'm thinking of using this on ceramic cookware. Is it heat resistant up to 500 degrees F
Answer:	MamaO - researched question - Do NOT use Gorilla epoxy on food ceramics. For other ceramics other than food, should be ok up to 180. From 200-500, epoxy will de-compose. / Look for food safe stuff only, but best to not repair your ceramic for food use. What you want is hard to find !

Product description

PC Products PC-Clear Epoxy Adhesive Liquid . PC-Clear is a completely clear liquid epoxy. PC-Clear is formulated to remain clear during and after its curing time. PC-Clear is very durable and flexible making it unlike many liquid epoxies. If disguising a repair or the absence of color is needed, PC-Clear is your product of choice. PC-Clear demonstrates excellent chemical resistance to mild acids, caustics, detergents, gasoline, fuel oil, salt, and fresh water. Note: PC-Clear will not bond to wax paper, Teflon, Polyethylene, and some other plastics. There are hundreds of plastics in thousands of combinations. Test a small area when in doubt.

From the Manufacturer

PC-Products, celebrating 60 years of “Fixing Your Things”, with quality, reliable repair products. Repair solutions for just about anything that needs repair or what you can manage to break. From Concrete to Wood restoration and heavy duty permanent repairs, we have you covered.Yeah; We can fix that!

• Clear epoxy adhesive liquid bonds wood, metal, glass, ceramic, concrete, and fabric
• When mixed it turns opaque initially then clear to full cure to blend in with bonded material
• Continuous service temperature range from -20 to +200 degrees F
• Provides work time of approximately 4 minutes, cure time for function of 1 hour, and full cure time of 24 hours
• Forms tough bond for durability

User questions & answers

Question:	Is it FDA approved
Answer:	It does not have an FDA approval. But I wont be eating this it does bond well on plastics and is solid, washable and clear. Held the item I used it on very well.
Question:	Does this glue settle to a smooth, shiny finish
Answer:	Smooth, shiny, tacky, &tough.
Question:	Will it repair broken Indian pottery
Answer:	This worked very well to repair some handmade ceramic pottery of mine. I can hardly see where the crack was.
Question:	can this be used to glue a sheet of stainless steel to wood? thanks
Answer:	As the product details say, "used to bond WOOD, METAL, glass, ceramic, concrete, and fabric."

Product features

PC Products PC-Clear Epoxy Adhesive Liquid

PC-Clear is a completely clear liquid epoxy. PC-Clear is formulated to remain clear during and after its curing time. PC-Clear is very durable and flexible making it unlike many liquid epoxies. If disguising a repair or the absence of color is needed, PC-Clear is your product of choice. PC-Clear demonstrates excellent chemical resistance to mild acids, caustics, detergents, gasoline, fuel oil, salt, and fresh water. Note: PC-Clear will not bond to wax paper, Teflon, Polyethylene, and some other plastics. There are hundreds of plastics in thousands of combinations. Test a small area when in doubt.

Great for high detail fixes

PC Clear is excellent for repairs and projects that must be less visible such as art objects or collectibles.

Strong flexible and resilliant bond

Durable and flexible yet demonstrates excellent chemical resistance to mild acids, caustics, detergents, gasoline, fuel oil, salt, and fresh water.

Proudly made in the USA

All PC Products are made in the USA and shipped from Allentown, PA.

About PC Products

Protective Coating Company was founded and incorporated in 1954 by John (Jack) Long as a service company providing customers with a waterproofing product called 'Spraycrete'. Soon afterward, our signature product PC-7 paste epoxy was developed. This product put Protective Coating Co. on the map. Today, we make a full line of repair and wood restoration products. From wood repairs to concrete repairs and most repairs in between...We have you covered.

Now in its 3rd generation, Protective Coating Co. still maintains their small town philosophy and remains a family run company committed to manufacturing quality products. Every batch of mixed material is still hand tested to insure our high standard of quality. In each of our products you will find more than just a product that performs as intended, you will find a team that stands behind their products. From Concrete to Wood restoration and heavy duty permanent repairs, we have you covered.Yeah; We can fix that!

Product description

Try to do some unique and special resin crafts with your creativity and imagination. It will be a special and meaningful gift for your family, children, friends as well.

You will get much fun and satisfaction of designing what you want!



Curing Time:

- UV Torch: About 1-2 minutes

- Direct Sun (Sunny Day): 10-15 minutes

- Direct Sun (Cloudy Day): 30-60 minutes



Package Included :

- 1 x 200g UV Resin



Please note:

1. In most cases, it will dry sticky if you don't use 36w UV light. But it can also cure totally if you put it in the strong sunlight for a long time.

2. It is not recommended to use this epoxy resin to make large objects such as ashtrays.

• CONVENIENT & EFFICIENT - Do not need to measure, mix the ratio or take long curing time like AB resin. Our UV resin is ready to use and can instantly cure hard in minutes with 36W UV light or sunlight. The spout does great help to squeeze and inject the resin.
• PREMIUM - Crystal Clear UV epoxy resin with self-leveling and self-degassing properties can cure smooth crystal clear, glassy finish. Anti-scratch, anti-stain and yellowing resistance.
• SAFE - Our hard type craft resin is imported from Japan and made from high-quality and non-toxic materials. There is an odor before curing, it is harmless and will completely disappear after curing.
• WIDELY USED - The clear UV glue can be used for jewelry making, crafts decorations, casting and coating, cast figurines and make resin paintings etc. It can also be mixed with mica powder, colorants, glitter to get colorful finishes.
• ECONOMICAL - Package includes 200g(7 oz) transparent UV resin which perfect design for all DIY handmade lovers or those who are just new to resin crafting. Click ‘Add to Cart’ and make sure to share your creative projects to us!

User questions & answers

Question:	What solution can be used to wash or clean the brush or tools
Answer:	Acetone works best to clean brushes and tools and sometimes whater eith soap can help but i say acetone is the way to go if ypu want a quick clean
Question:	Does it shrink
Answer:	If the power of the UV lamp is high, it does shrink a little.
Question:	Can this be baked in the oven once fully cured? I wanted to use this to glue glass cabochons to drawn eyes and later baked inside polymer clay
Answer:	Dear Dominique Andre, Hello! No, uv resin can not be baked in the oven. Hope this could help!
Question:	Can this be used on tumblers
Answer:	I used it on a tumbler and it came out great 😊 I let it cure outside on a very sunny day and it dried quickly and it’s not sticky at all it came out perfect and it’s been 3 months now and it’s still looks great I use my tumbler everyday so far do good.

Product features

Package Included:

• 1 x 200g UV Resin
• 1 x Squeeze Nozzle

Fast Curing ----------

• UV Torch: About 1-2 minutes
• Direct Sun (Sunny Day): 10-15 minutes
• Direct Sun (Cloudy Day): 30-60 minutes

Self Degassing --------

• The smell of the resin would disappear after fully curing
• The finished resin is odorless

Heat Proof -----------

• Can bear high temp up to 248 ℉
• If the temperature is too high, the resin would soften and yellowing

Yellow Resistant -------

• Crystal Clear
• Highly Durable

MSDS File ~~~~~~~~~~

• We have a file containing detailed INGREDIENTS LIST.
• Please click 'Limino US' and then click 'Ask a question' button if you need it.

Quick Response ~~~~~~~~

• Feel free to ask questions about uv resin.
• We will answer it ASAP.

Replacement ~~~~~~~~~

• Defective resin? You'll get a replacement.
• Not satisfied with the resin? We'll fix it!

Product description

Are looking to save time and money searching for a super high gloss finish? Look no further. We have hundreds of happy customers loving our resin over the big box generic brands that charge premium prices.

Our Epoxy Resin is 100% made in the United States of America. You will simply love this super high gloss finish epoxy resin! We ship our product on the same day of your purchase.

Special Note: Your kit starts at 1-gallon combined. That means you get about 1/2 gallon of resin and 1/2 gallon of hardener. The resin weighs approximately 4.10lbs. pounds and the hardener weigh approximately 3.15 pounds.

Benefits: Cures very hard Exhibits good air release Excellent chemical and water resistance Finished product cures crystal clear with a super high gloss finish Easy to use 1:1 mix ratio (By Volume) (Example 1 cup to 1 cup) Excellent for all Wood applications Curing: This product provides the fastest cure and property development at ambient and low temperatures without accelerators. This allows for a quick return to service. The typical pot-life on this item is roughly 45-50 minutes based on mass and temperature. Thin-film set time (3mil. film) is roughly 5 hours at 78F. Fast cure and green time while exhibiting low exothermic temperatures (120C.) makes this product ideal for all applications. The full cure is 24 hours at normal conditions.

This product cures to a brilliant high gloss finish. The finished product will be very rigid, smooth, clear, and display a brilliant high gloss finish similar to glass.

• Crystal clear epoxy resin for table tops , Bars, Fiberglass and Concrete
• Professional Grade High Gloss Finish multi-purpose resin
• 1 Gallon Kit Combined ; 1 part resin and 1 part hardener
• Our Epoxy Resin is 100% made in the United States of America

User questions & answers

Question:	Would this product be suitable to cover a painted wooden spool table that will live outdoors? Im in Ohio, so winters temps are sometimes below 0 degr
Answer:	Yes , This resin is good for wooden spool table
Question:	Is this FDA approved
Answer:	I’m sure it is but don’t Qoute me
Question:	Is this suitable for fiberglass and carbon fiber
Answer:	Yes it is.
Question:	Is it for concree countertops
Answer:	Yes, you can use it on concrete countertops.

User questions & answers

Question:	will sealing bare wood surface prevent bubbles forming
Answer:	The product should be applied in two stages. The first stage is referred to as the seal coat. The seal coat is a small batch of epoxy that is brushed on in a thin layer to seal any pores in the surface and prevent air bubbles from forming in the following flood coat. Our epoxy is used for both your seal coat and your flood coat.
Question:	Is this FDA compliant
Answer:	Yes, here is the response from promarine supplies "Although we do not have FDA approval certificate, our epoxy does comply with FDA Compliant Coating for Direct and Indirect Food Contact. Our Epoxy is VOC-Free and user-friendly. Once the epoxy is cured, it is an inert plastic that is non-harmful or hazardous." I have also shared some information from our websites in the link below. https://promarinesupplies.zendesk.com/hc/en-us/articles/115001444873-Is-Pro-Marine-Clear-Table-Top-Epoxy-FDA-Compliant-or-Food-Safe- https://www.promarinesupplies.com/www.promarinesupplies.com/blogis-pro-marine-supplies-epoxy-food-safe/
Question:	Will this work over Minwax polyurethane (oil based). i see it wont react well with oil based stain so i applied poly over the stain. thoughts
Answer:	epoxy can go over them in about 24 hours. OIL BASED paints take a LONG time to fully dry. If an oil-based paint is used, you must apply 3 coats of oil-based polyurethane to seal the surface before applying a seal coat of our UltraClear epoxy. If you go directly over the oil-based paint and it is not completely dry, you run the risk of the epoxy not sticking to the surface and peeling off months later.
Question:	how many square feet does it cover
Answer:	it depends on how thick you put it. First time I used it, 1 gallon for 80 square feet. second time I used 5 oz thinner to 1/2 gallon and covered 80 square feet.it all depends how thick you spread it.

Product features

High Gloss & Durable

High performance and Crystal clear! Produces a tough, high gloss, water and scratch resistant coating.

Versatile

Can be used for a wide variety of applications, art, and home projects.

Food Safe

Food Safe formula for artistic items used around food, such as trays, tumblers, and glassware.

Easy 1:1 Self Leveling Formula

Use our product with ease, featuring an easy 1:1 self-leveling formula!

Beautiful and Versatile, Crystal Clear Finish...Every Single Time!

Step 1: Measure

Pour equal parts of resin and hardener into a clean mixing container or graduated mixing tubs, using a 1:1 ratio (by volume) It is crucial that the product is measured accurately and mixed thoroughly. Measure 1 part RESIN to 1 part HARDENER by volume. Do NOT vary this ratio. Our Epoxy is formulated to cure at a specific mixing proportion, and any variances can cause the product never fully to cure. We recommend always pouring the HARDENER into your mixing container first, followed by the RESIN. This will help the two components mix thoroughly.

Step 2: Mix

First Mix: Mix with a flat bottom stir stick or spatula being sure to scrape the sides and bottom of the container as you go. Your mixture will appear hazy at first, and then become more transparent as the resin and hardener molecules begin to blend within three to five minutes.

Second Mix: Pour the Resin and Hardener from your first container into a second container scraping all the mixture out from the sides and bottom of the cup. Thoroughly mix for an additional three minutes.

Step 3: Seal Coat Stage

The best way to apply a seal coat is to start on one end of the table and pour the resin all the length of the surface, zigzagging as you go. Then use a foam brush to drag the resin across the entire surface to achieve an even coat. The epoxy cures rather quickly in the container, so it is necessary to paint the seal coat on quickly or mix up a smaller amount so that it does not cure in the container while you are still working on it. The seal coat does not need to be smooth as the flood coat will fill in the brush strokes and irregularities making it crystal clear. Once the entire surface is sealed, wait 4-6 hours to pour the flood coat. Do not exceed 10 hours or you run the risk of the flood coat not blending into the seal coat flawlessly.

Step 4: Flood Coat Stage

Each flood coat self-levels at approximately 1/8” thick. If depths thicker than 1/8” are desired multiple coats are necessary. You must wait at least 4 to 10 hours between flood coats. The epoxy will still be tacky so the next pour will stick to it.

The best way to apply the flood coat is to start on one end and pour the resin the entire length of the surface, zigzagging as you go. After you are finished pouring, set the container down. Do NOT try to scrape anything else out of the bucket. Because you are pouring about three times the amount of product you did with the seal coat, the material will immediately start to flow out.

Step 5: Remove Air Bubbles

Once you have sufficiently covered the entire surface with your flood coat, you will begin the process of popping air bubbles. The best tool for removing bubbles is a small propane torch. Hold the flame approximately 6 to 10 inches away from the table top and quickly sweep across the entire surface using an ironing motion. You will immediately see the bubbles start to pop. Do this until all the bubbles are gone from the surface of your table.

* After pouring your epoxy, it is common for air bubbles to form. Bubbles can continue to develop for up to 60 minutes after the curing process has begun. The most efficient way to get rid of them is to run a blowtorch over the surface sporadically 10 - 15 min at a time.

Step 6: Curing Process

After applying your final coat, the product should be kept in a clean, dust-free environment at a minimum of 75-80° F degrees. The product takes approximately 12-14 hours to dry to the touch. However, the product should not be put into any use for at least three days which will allow it to achieve sufficient hardness to resist scratching. At temperatures below 75 F, the product will take longer to cure and might not cure to complete hardness.

Product description

Devcon 5-Minute Epoxy adhesive cures and joins materials together by a chemical reaction between the resin and hardener. This reaction results in a high strength bond that is resistant to most chemicals. Use Devcon Epoxy adhesive for household, industrial, crafts or for any job that requires a high-strength, high-quality bond. Works best on metal, wood, concrete, glass, ceramics, china and much more. 5 Minute Epoxy sets in 5 minutes with strength up to 1,500 lbs. per square inch. Dries clear; water resistant. Includes 2 bottles with 4-1/2 ounces of epoxy.

• Ideal for joining wood, metal, concrete, glass, ceramics, china and more
• Sets in 5 minutes with strength up to 1,500 pounds per square inch
• 2 bottles included; 4-1/2 ounce bottles
• Dries clear
• water resistant

User questions & answers

Question:	Will this work for a finishing coat on fishing lures
Answer:	no,however duracoat makes a clear air dry spay can gun finish, it's expensive . most people use marine varnish, urethane or lacquer.you can also use clear epoxy paint.
Question:	Will this flow? I need something that self levels
Answer:	Yes but it drys in 5 minutes. So mix fast and spread. I use it for knife scales and it works perfectly
Question:	what kind of pigment should be used to tint epoxy
Answer:	This epoxy is clear. You could use a paint pigment.
Question:	Is it UV resistant
Answer:	I have no technical knowledge re you question, my applications are typically covered by paint.

Product description

Devcon epoxy adhesive cures and joins materials together by a chemical reaction between the resin and hardener. This reaction results in a high strength bond that is resistant to most chemicals. Use Devcon Epoxy adhesive for household, industrial, crafts or for any job that requires a high-strength, high-quality bond. Works best on metal, wood, concrete, glass, ceramics, china and much more. 2-Ton Epoxy sets in 30 minutes with strength up to 2,500 lbs. per square inch. Dries clear; water resistant.

• Ideal for joining wood, metal, concrete, glass, ceramics, china and more
• Sets in 30 minutes with strength up to 2,500 pounds per square inch
• Includes 2 bottles; 4-1/2 ounce bottles
• Dries clear
• water resistant

User questions & answers

Question:	After opening, what are the components shelf life? Anyway to lengthen their viability
Answer:	Bought some of this same brand/same size "at least" 40 years ago! It was kept (unfortunately) in my garage (NO HEATING OR AC) for most of this time... temps here can range anywhere from a low of 12 degrees. F to 105 degrees during the course of what one could consider a "typical" year. To my EXTREME SURPRISE...This stuff worked great up until LAST YEAR!!! The resin now appears to show some signs of "separation", but even still... if I take time to assure the resin is stirred in the bottle to a consistent appearance before dispensing, it will still harden and secure the items I use it on. It takes longer to reach a full cure than in the past, but works for my non-critical needs. I can't comment on whether it has the same total bonding power as when new, but it DOES still bond! I am however now finally buying a NEW set so that I can put projects in service based on the product's original "full bonding time frame" (mine takes longer now), and for items that are either too difficult access at will (for a potential re-do") or too critical in function to take chances with bonding failure. GREAT PRODUCT provided they haven't monkeyed with the formula since I bought mine! Even drinking water has a "shelf-life", so I'm totally amazed this stuff has performed so well during the 40 years or so I've had it!!!
Question:	Will it melt blue styrofoam
Answer:	oh yes as fast as it hits it, jim
Question:	Two questions: Is the mix pourable, and what is the maximum temperature that the cured resin can tolerate
Answer:	After mixing, the mixture is viscous but can still be poured (immediately). Maximum temperature before release of toxic fumes is
Question:	I'm really looking for something equivalent to super glue but in this size bottles. Question is do need to use and mix both bottles for it to glue
Answer:	need to use equal parts of each tube, mix well. drying time will be stated on tubes, depending on type you buy...30 sec. to 30 min. or more. usually acetone clean-up before dried, acetone soak will also release bond, as will heat over 325 degrees.whatever quantity needed will still be a 1-1 mix, but keep in mind working time vs dry time, so not to mix more than you can use before hardening. denatured alcohol can thin mixture

Product description

QIAO QIAO DIY advanced red bottled UV Resin

1.Self Degassing:

Low odor

The finished resin is odorless

2.Yellow Resistant:

Crystal Clear

Highly Durable

3.Fast Curing:

6W-9W LED light(405nm): 30-90 seconds

36W UV lamp: 2-4 minutes

Under direct sunshine: around 30-90 seconds

Cloudy day: around 20-40 minutes

(The curing time will be extended after adding color pigment or other materials)

 

Package Content

1pc red bottle of QIAO QIAO DIY UV Resin

(with Squeeze Nozzle)

• This UV resin can be cured under UV or direct sunlight within a few minutes.So please do not store it under direct sunlight to prevent hardening.
• Made of non-toxic and high-end materials,harmless and low odor,it performs surprisingly in curving efficiency and anti yellowing.
• The pointed nozzle is convenient to use and control the flow of resin.Just squeeze and inject the resin with it.
• Can be mixed with other material,such as dye and pigment,to make your jewelries and crafts more beautiful,or decorate your cell phone,earphones and so on.
• It’s a special and meaningful gift for your family and friends.There is a lot of fun and satisfaction waiting for you from designing and making resin crafts.

User questions & answers

Question:	can this be used for tooth gems and cured with a UV light
Answer:	Hi Emily, UV Resin is good for crafts. May you approach the dentist for their opinion though the products already used by them before. Thanks
Question:	Can this be used to incase pressed flowers
Answer:	Yes it can.

Product description

Artist Approved UV Resin Designed For Your Imagination Everyone can be an artist! Our UV Resin can be used for small items making, crafts decorations, casting and coating, etc, cast figurines and jewelry, make resin paintings and more. It can also be mixed with mica powder, colorants, glitter to get colorful finishes. Show your unique creativity! Art makes life more interesting!

• AWESOME UV RESIN: Use our clear UV resin for all of your casting AND coating applications. UV resin is ready to use and can instantly cure hard in minutes with 36W UV light or sunlight. Do not need to measure, mix the ratio or take long curing time like AB resin. The nozzle does great helps to squeeze and inject the resin. Simple but all-match.
• PREMIUM: Rigorous testing was done. Super transparent UV epoxy resin with self leveling, self degassing, odor free, high quality and can cure to a smooth and clear crystal shape. Super clear, Anti-scratch, anti-stain and yellowing resistance. Great assistant for DIY craft.
• SAFE: Our hard type crafts resin made from high-quality and non-toxic materials. NON-sticky, super clear and NON-shrinkage. NO strong odor and yellow issue. Safe & healthy.
• WIDELY USED: UV Resin can be used for small items making, crafts decorations, casting and coating, etc, cast figurines and jewelry, make resin paintings and more. It can also be mixed with mica powder, colorants, glitter to get colorful finishes. Show your unique creativity!
• PROVIDE the BEST CUSTOMER SERVICE. The youngfocus company, that offers the absolute best customer service in the industry. It is economical and highly cost-effective, low profit for better customer experience. If for any reason you decide that this uv resin is not for you, to send email us and receive a 100% money-back refund.

User questions & answers

Question:	Will this work on PVC pipe
Answer:	I'm sure that it would bond the two PVC pieces together, but if the PVC application is for anything other than a stand or a template of some sort, I would not use it. They make PVC primer and glue that you can get at any hardware store and it's very cheap.
Question:	What is the shelf life on this product
Answer:	In 2015 I had this product go 7 years after the expiration date listed on the product & it still performed reliably. It is a good product.
Question:	Will this glue magnetic drawer catches to plastic drawers
Answer:	Yes, I use this glue all the time to attach magnetics to metal and plastic.
Question:	Do I have 5 minutes to get the broken pieces of a ceramic plate lined up properly before it sets
Answer:	No. When properly mixed for about one minute, you’ll have about 2 minutes before hardening sets in where you cannot adjust. After 5 minutes the epoxy will be set. It is suggested to leave for 24 hours for full curing. I like using this epoxy as I can generally hold a piece in place for 5 minutes.

• What you get - 1 bottle 500 grams resin, 1 bottle 500 grams hardener (1:1 Ratio By Volume, total about 35oz) .
• Feature A - The resin kit is crystal clear and self level. Please ensure 1:1 ratio by volume, stir in 3 to 5 minutes with gentle mixing, and then pour the resin into the molds asap.
• Feature B - This 2 part casting resin can match most coloring pigment like resin dyes, alcohol ink, glow in the dark, resin powder dye and other liquid colorant pigment.
• Usage - You can use this epoxy resin hardener kit in resin paiting project, jewlery wood metal artwork project, sculpture, crystal clear coating and other resin project.
• About DROLE - If you have any problems or suggestions with our product, please feel free to contact our customer service team and we will find out a best solution for you and treasure all our customer's idea.

User questions & answers

Question:	Do I need a UV light for it to work
Answer:	No, you don't need a UV light for these clear epoxy resin. You can place them for curing about 12 to 24 hours. The time is due to the temperature, the warmer the day, the less time the curing time take. Thank you for your question! Regards, DROLE Jewelry Making
Question:	Can I use alcohol inks, resin pigment or pearl powder with this product
Answer:	Yes, friend. These epoxy resin is compatible with many resin dyes. The can use with alcohol inks, resin pigment or pearl powder. Thank you for your question! Regards, DROLE Jewelry Making

• ✔ CRYSTAL CLEAR - Our Table Top Epoxy cures ultra clear making it perfect for table tops, bar tops, and countertops
• ✔ UV RESISTANT - Unlike many other epoxies, our epoxy resist yellowing caused from exposure to Ultra Violet Light Sources
• ✔ SELF LEVELING - Bar Top Epoxy self levels on application including corners, over bar rails and edges.
• ✔ HIGH GLOSS DURABLE FINISH - Epoxy resin leaves durable, blemish resistant, water resistant and impact resistant coating
• ✔ 100% SOLIDS - Low Odor, ZERO VOC, consistent thickness, quick curing 1 to 1 mixture, 1 Gallon Kit

User questions & answers

Question:	Is it required to use a ventilator mask when using? and is this Resin food safe
Answer:	It is not required. However, you should use the epoxy in a well-ventilated area. It is possible to be food safe. However, because the customer is mixing/pouring we cannot say this is food safe. Each mixture/application would have to be assessed individually.
Question:	Id like to dye the epoxy different shades of green but I need it to stay transparent. Any suggestions
Answer:	There are various dyes and pigments to choose from. It really depends on how deep of a green you'd like while maintaining transparency. I would suggest trying multiple on a sample area so that you can gauge the color/transparency of the pigment/dye.
Question:	I have stained my bar top with an oil based stain. Can I use the epoxy over it or do I need to do some other prep
Answer:	You can use a water-based clear coat on top of the stain. After the clear coat has cured, use a 320grit sand paper to take the shine off. You can then apply the table top epoxy.
Question:	What’s the diameter of the cap? I want to buy pumps to fit, thanks
Answer:	The cap is 1.5 inches in diameter. Let us know if you have any other questions. Thanks!
Question:	How much does it discover ( sq feet
Answer:	Covers apx 750 sq inches.
Question:	I have a heavy marble table, the bottom mount under the top broke off, would it be strong enough for this application
Answer:	I got a job to put together a 13 foot marble altar, weighing several tons. I used this stuff to glue the hundreds of marble pieces together, after testing the bond strength, and it's still standing today. Granted there isn't any real strain on the joints in most places, but the bond is stronger than the marble itself. This is good stuff.
Question:	Can it fix on the cracks of corina counter top
Answer:	Hi Chris,It is great for crack repair as long as the crack is wide enough to be able to get the material down in it. A good rule of thumb is that crack needs to be wide enough to get a credit card wedged between. Good luck!
Question:	What type of colorant can be used with the product - is the resin considered a polyester resin. The product details are not very precise
Answer:	For coloring the resin I have used Custom 4 Coloring Kit for Epoxy Gluing or Repairing of Granite,...Sold by: GRANITE POLISHING PADSYou can order this item from amazon. The dye is very efficient and seems to work very well with the resin. Yes this epoxy appears to be some sort of polyester. As soon as u add the hardener the epoxy hardens fast but it gives you enough time work with. My results were very good although didn't polished it yet. Good luck

Product features

Crystal Clear Finish

High gloss, ultra clear finish makes our epoxy perfect for Table Tops, Bars Tops, Coffee Tables, Live Edge Tables and other coating applications. However, epoxy is not flexible. River tables must be supported to prevent flexing which could cause cracking.

*Do not pour over oil-based paint or stain.

Common Question: My project is painted or stained with an oil based product, what can I do?

A: You can apply a water based clear coat (must be water based). Once the water based clear coat has fully cured, you can apply the epoxy. If the clear coat leaves a shine/gloss you may want to scuff the surface to ensure the epoxy properly sticks. We recommend using 320 grit sandpaper. If you do sand, be sure to thoroughly clean the surface prior to applying the epoxy. We recommend using Isopropyl Alcohol 99% (be sure it is 99%) to clean.

UV Resistant

Although most epoxies will yellow over time, some resist yellowing caused by exposure to ultraviolet light better than others. Our epoxy contains UV Inhibitors which helps to resist yellowing. *Although our epoxy is UV resistant, which resists yellowing, we do not recommend leaving finished projects in direct sunlight or for permanent outdoor applications.

Common Question: Can I use this on a table that will be outside on a covered patio?

A: It is possible to leave the epoxy outdoors if not exposed to direct UV exposure. If the epoxy is exposed to direct UV, the epoxy can yellow. This will be more noticeable on white or lightly colored substrates/surface. We recommend exercising caution when considering use over white or light-colored surfaces.

It is also important to consider temperature fluctuations. Materials such as metal and glass can expand and contract at a different rate from the epoxy. This could cause glass to crack or the epoxy to peel away from a metal surface.

Food Safe Epoxy

Properly cured epoxy is possible to be food safe. However, because the customer is mixing/pouring we cannot say this is food safe approved. Each mixture/application would have to be assessed individually. This is not a high heat epoxy. We recommend using hot pads/coasters for coffee mugs, hot pans, pots, etc.

Common Question: Can I use this epoxy to make tumblers?

A: We have many customers using our epoxy for custom tumbler designs. However, this epoxy self levels. Therefore, many customers utilize a "cuptisserie" which is a rotating device that keeps the tumbler rotating while the epoxy is curing so that the finish is even.

Again, keep in mind: Properly cured epoxy is possible to be food safe. However, because the customer is mixing/pouring we cannot say this is food safe approved. Each mixture/application would have to be assessed individually.

Colored Epoxy Compatible

How To Color Epoxy: Our epoxy mixes well with mica pigment powders for colored epoxy applications. River tables, resin art canvas and more may require tinted epoxy. Epoxy is not meant to be mixed with or poured over oil-based products. Do not pour over oil-based paint or stain.

Common Question: What type of pigment or dye should I use with this epoxy.

A: We do not recommend mixing epoxy with paint or anything oil based. Many of our customers use mica pigment powders. Mica pigment powders come in many different colors, glitters, metallics, and even glow in the dark.

Q: How Much Pigment Powder Should I Use?

A: This is a subjective answer as it depends on the certain hue and level of opacity desired. We suggest starting with a very small amount and adding more until the desired color is achieved. We also always suggest testing a small scrap piece of material to understand how the epoxy will flow and how the color will cure in the epoxy.

Easy To Use 1:1 By Volume Mixture

Self Leveling, Impact Resistant, Superior Air Release

Popular uses include wooden bar tops, river tables, embedding pictures or embedding solid objects into a desired surface. Because our epoxy cures crystal clear, multiple layers will not compromise color/transparency. Each poured layer should not exceed 1/4" at a time. Working Time: 25 (+/-5 Minutes)

How Much Epoxy Do I Need?

Our rule of thumb regarding coverage is 12 sqft per mixed gallon at 1/8 inch.

Family Owned Business, Made In USA

VARIETY OF APPLICATIONS

For Uses On

• Wood
• Concrete
• Bottle Caps
• Artwork
• Canvas

Common Question: Can I apply epoxy over paper products like photographs, cigar wrappers, playing cards, and more?

A: If you wish to apply paper decals, bottle caps, or other objects under the Table Top surface, those objects need to be bonded to the surface with craft glue or a thin layer of Table Top Epoxy. Paper products must be sealed prior to applying any epoxy as the epoxy could soak in and ruin the paper product.

You can use something like mod podge or a similar water based clear coat/glue. Allow this seal coat to dry thoroughly before applying epoxy. For figurines, shells, and other large more three-dimensional items, using a thin epoxy seal coat is best, prior to encapsulating.

HIGH GLOSS FINISH

Epoxy resin leaves durable, blemish resistant, water resistant and impact resistant coating.

The beauty of epoxy is the ability to recoat a surface after years of use to regain a smooth, high gloss finish.

Common Question: I see that your epoxy requires thin pours of no more than 1/4" per application. How long do I need to wait between pouring a new layer?

You can apply the second coat when the prior coat is tacky to the touch (usually 4-6 hours depending on temperature). If you wait longer than 12 hours between coats, we recommend a light sanding. You can use 320 grit to scuff the surface. This will help the next coat to properly stick. If you do sand, be sure to thoroughly clean the surface prior to pouring the flood coat. We recommend using Isopropyl Alcohol 99% (make sure it is 99%) to clean.

TOP QUALITY

Incredible Solutions Table Top Epoxy is proudly MADE IN THE USA.

Competent Knowledge Base helps plan and troubleshoot even the most complicated projects.

Common Question: Does your epoxy require specific temperature environment to mix/pour epoxy?

A: The ideal working temperature is around 77°F. Best results can be obtained at temperatures between 75°F and 85°F, in a clean, dry, dust-free environment. Avoid working in high humidity. It is important you keep your project in this environment throughout the entire curing process. We recommend using this product on a leveled and flat work surface so that it can flow and self-level properly.

Product description

Miraclekoo UV Resin Hard UV Glue Ultraviolet Curing Solar Cure Resin Sunlight Activated Crafts For DIY Jewelry Making



Features:



Color: Transparent , Weight:120g / Bottle.



Cured with UV / sunlight, no mixing like AB resin.



UV Resin Cured hard within minutes, no more waiting , UV Lamp(36w): 2-4 minutes, Direct Sunlight (Sunny Day): 10-15 minutes



Please note:

1. In most cases, it will dry sticky if you don't use 36w UV light. But it can also cure totally if you put it in the strong sunlight for a long time.

2. It is not recommended to use this epoxy resin to make large objects.

• EASY TO USE & EFFICIENT:No mixing like AB resin which needs to mix and take long curing time , our art resin require no preparation and ready to use.Instantly cured in minutes with UV / sunlight.UV Lamp(36w): 2-4 minutes, Direct Sunlight (Sunny Day): 10-15 minutes.
• PREMIUM - Crystal Clear UV epoxy resin with self-leveling and self-degassing properties can cure smooth crystal clear, glassy finish. provides excellent scratch resistant, stain resistance and yellowing resistance.
• SAFE - Our hard type uv resin is made of high-quality and non-toxic materials.There is an odor before curing, it is harmless and will completely disappear after curing.
• WIDELY USE - Excellent for jewelry making, open back bezels, bezel setting, small silicone molds,crafts decorations, casting and coating, cast figurines and make resin paintings,garment accessories, encapsulate objects, make resin paintings etc.
• ECONOMICAL - Package includes 120g(4.2 oz) transparent uv resin which perfect for DIY craft making!Comes with small tip, simply open and squeeze.

User questions & answers

Question:	Does the cured resin turn yellow after time
Answer:	I too have an issue with it.... it glows a greenish color under uv light (only resin i have bought that does this.) It also does have a tint to it in my pendants... i posted pics in review, hoping company will reach out to me, but no luck. I have bought it in the 500 gram bottle and have an awful time with tiny bubbles that look like tiny black specs till cured... going back to my old company, would rather spend more money for less product then deal with this... too many complaints from customers since i switched. I make pendants that you can see through, so it obvious to see the weird tint it has.... maybe it is the chemical catalyst they use to make it uv cureable. And also... ALL UV RESIN EVENTUALLY GETS A YELLOW TINT....
Question:	Do you need to buy a UV light
Answer:	Yes and no. You’ll need either a uv light OR direct sunlight (not through windows).
Question:	Is it FDA approved
Answer:	As in safe to use for food products? Doubtful . It has a pretty strong seem while it’s curing. I recommend washing your hands if you touch it for the first time as it does have a residue.
Question:	I want to use this to make free form tear drops, rain drops, puddle. When it leaves the bottle does it hold it shape or spread all over
Answer:	It spreads. If you want something with more control you might have to use Epoxy by letting it cure till it reaches the consistency you’re looking for.