13 best dryer vent pipes

Product description

Builder's Best 011718 All Metal SAF-T Single Elbow Dryer Vent Duct Kit, UL Listed, 4" Diameter x 8' Length

• This is a 8-feet UL Listed flexible metal (semi-rigid) transition duct attached to one Close Elbow. The original Close Elbow by Builder's Best is designed to make 90˚ turns within 4″
• Maximum velocity for this duct is 5,000 FPM. Temperature can range from - 100 degrees Fahrenheit to + 430 degrees Fahrenheit
• UL Listed and Labelled: Complies with all clothes dryer manufacturer recommendations
• Comes with 2 additional steel screw clamps
• Quality made in the USA by Builder's Best, Inc. Builder's Best brand is a US registered trademark. SAF-T-DUCT is a registered trademark by Builder's Best, Inc. SAF-T-DUCT Dryer Venting is the trusted solution for professional installers nationwide. It meets all clothes dryer manufacturer specifications

User questions & answers

Question:	Can this be used for oven hood duct system
Answer:	Sure it can be used as a hood duct, on the premise that you have access to cleaning weekly it and that your range hood cfm requirements are so low that it only needs a 4 inch duct. Or get an hvac person to ask questions or do that job for you, since your question was asked, I assume you are not proficient with HVAC cfm requirements for a range hood or the constant cleaning/dangers that are involved in using a duct system with ribs. Good luck!
Question:	are u able to connect more than one piece together? ex 16' of this
Answer:	You would have an elbow on each end but if that is what you need then yes you can connect two 8' to make 16'.
Question:	I purchased this kit and installed it on my drying. The hose gets hot even when I'm drying on a low setting. Is that normal
Answer:	Of course, you are venting very hot air and its metal. Plastic vent ducts do not get as hot.
Question:	Could this be used for bath exhaust? I need the 90 to vent through the soffit which is a tight fit
Answer:	This is an exhaust vent pipe. If it fits it should work for any vent. It is flexible and will bend to fit.

Product description

Power is the leading manufacturer of grow light systems; supplying gardeners, worldwide, for over a decade. We use the transformative power of light to make gardening more efficient and productive. In addition to HPS/MH and Ceramic MH technology, we offer digital ballasts, fluorescent, and LED lighting systems. From hobbyist to commercial applications, we offer a broad spectrum of gardening tools and equipment in hydroponics, irrigation, climate control, and structures to help your garden thrive. Power Ventilation Ducting is made from high quality aluminum to provide flexibility and protect against breaking during installation. Not only does the duct act as in intake and exhaust piping for active-cooled fixtures and reflectors, but also stores and dissipates heat at a steady rate, which reduces room temperature fluctuations. Benefits of power Ducting: This 4-inch ducting fits any standard 4-inch inline fan. 3-layer thickness: Aluminum Foil + PET + Aluminum Foil. Helically shaped and internally crimped galvanized steel strip. Interlocking steel strips to form an air tight and leak proof system. Each ducting unit includes a pair of metal clamps made from stainless steel. This air duct is easy to cut using a pair of metal snips or a standard wire cutter. This ducting is easy to bend to install in hard to reach spaces such as grow rooms, attics, crawl spaces, etc. This ducting is made with aluminum reinforced with a spiral-wire, designed to prevent the ducting from unraveling when cut into smaller pieces. Typical applications for ventilation ducting include: Dryer room vents, A/C or Heater ducting, grow room ventilation and other indoor gardening applications. 12-month manufacturer.

• Ducting size: 4 inches (diameter) x 8 feet (length) when fully extended
• Thermal endurance: Temperature endurance range from 0 ~ 185°F. (-18℃ ~ 85℃)
• Wide applications: Kitchens, bathrooms, greenhouses, grow rooms, grow tents, etc.
• Easy installation: 2 pairs of 4 inch metal clamps made from stainless steel. Flexible length for exhaust fan blower/inline fan
• Fire proof coating: Flexible ventilation ducting made from high-quality flame-retardant aluminum and built-in corrosion-resistant wire helix for reinforcement and lasting performance

User questions & answers

Question:	Does this fit any dryer
Answer:	No it does not. I went to Walmart and picked up a few.
Question:	Can I Recycle This
Answer:	Yes, I am currently using it for an outlet on my dryer.
Question:	My dryer is sticking out more than the washer. They told me to get a different vent duct so I’m able to push the dryer back some. Is this it
Answer:	Yes. It should then use venture ductwork tape, clamp or large duct zip tie to make a tight secure seal.
Question:	Will this fit in a 4" port on a Milliard 36 x 36 73 grow tent
Answer:	No. I wouldn’t use this. Higher temperature applications require a different flex usually all aluminum for dryer venting because of the moisture levels being exhausted.

Product features

iPower Non-Insulated Flex Air Aluminum Ducting for HVAC Ventilation

Flexible Length

Flexible length for exhaust fan blower / inline fan; quick and easy to set up.

Durability

Built-in steel wire for reinforcement and long lasting performance.

3-Layer Thickness

Flame-retardant coating. Temperature endurance range from 0 ~ 185°F (-18℃ ~ 85℃).

Product description

This Dryer Telescoping Vent Periscope measures 0-in L to 18-in L and is designed to use in small laundry spaces with 2-1/2-in clearance. It features one male snap-lock fitting and one extra long draw-band collar for easy installation; excess length can be trimmed to fit. The beveled ends of the item prevent interference with or damage to floors and wall. This product is an accessory item compatible with several brands; check to see if your model number is compatible. Installing this accessory will require basic hand tools and novice repair experience.

From the Manufacturer

This periscope can range from 0 to 18 inches depending on preference. It includes one male snap-lock fitting and one extra long draw-band collar. Keep in mind that any excess length can be trimmed to fit according to your needs.

• Adjustable dryer vent (up to 18 inches)
• Includes a male snap-lock fitting and extra long draw-band collar for easy installation
• Closest to wall application is 2-1/2 inches
• Helps safely save valuable space in your laundry room
• Part No. 4396037RP

User questions & answers

Question:	can u pull it apart and reverse one side so both holes are on the same side or is it truly periscople style only
Answer:	No, it can't be reversed as others here have said, at least not without a lot of cutting and taping which sort of defeats the purpose. I had to return it and buy the 18-27 inch version instead.
Question:	Can this be used with a gas dryer. Thank You
Answer:	Of course. The vent pipe doesn't know gas from electric. Hot is hot!
Question:	Do you just cut this in half with tin snips and slide part of it back over itself and then tape it
Answer:	No cutting. It is already in two pieces. It slides up and down and slide it apart for what ever length you need. My husband is a contractor and said it does not need taped if you don't want to tape it. Fits tight. Hope this answered your question.
Question:	Is this 18" from the center of each opening to the other? Or 18" from the very end of the "box" to the other end of the "box"? I need to reach 17" from the exact center of each opening
Answer:	If you look at the layout of the pipe, it should be 18-20" Center to Center and 24" overall. This is per site: partselect.com and type in the model number. The grid is 1" squares.

Product features

Whirlpool Original Equipment Manufacturer (OEM) Accessories

We know appliances inside and out, which means we don’t just offer accessories for one brand but we offer accessories for all of our brand appliances; Whirlpool, Maytag, KitchenAid, Amana, and JennAir. Whirlpool OEM Accessories are perfect for your installation and enhancement needs.

Quality Tested & Trusted

Our accessories are put through the same testing and quality procedures as our products, meaning you can trust they are up to our quality testing.

100 Years of Experience

Created with over 100 years of history in American appliance manufacturing, you can keep all your machines running their best when you bring Whirlpool home.

Product description

VENT SYSTEMS is a company with a long tradition and experience. We provide innovative solutions in the field of ventilation of premises. We are constantly striving to develop and deliver even better, more advanced and more efficient technologies that would enable our customers to enjoy healthy fresh air indoors. All products undergo thorough quality control before going on sale. We also guarantee professional service and periodic maintenance system for maintaining system reliability for many years. We have created the value of the VENT SYSTEMS brand by putting particular emphasis on: HIGH QUALITY OF THE PRODUCT - WIDE RANGE OF PRODUCTS - MEETING THE CUSTOMER'S NEEDS.

• Back draft damper for insertion into 4 inch ventilation ducts. The backflow damper opens and closes automatically. It has a strong spring and can be installed either horizontally or vertically. The flap is suitable for retrofitting, since it is completely inside the duct
• A tight sealing and fastening of the duct is achieved by the rubber strip attached to the inside of the draft blocker damper. The rubber seal prevents loud rattling when the flap blades open and close. The housing of the flap is made of galvanized steel, the flap blades are made of aluminum, the axle and spring are made of stainless steel
• Designed for use in AC, dryer vent, exhaust, extractor or range hoods, heating systems, fans, vents and other residential, commercial and industrial HVAC applications. Best to use with VENT SYSTEMS hvac parts.
• Duct draft stopper prevent cold air or wind from entering the ventilation pipe. In this case, the flap is installed in such a way that the flap leaves only open into the outgoing air direction. This means that no cold air / wind or smell can penetrate the ventilation pipe from the outside.
• The backflow Preventer valve is installed by pushing it into the ventilation pipe as far as it will go. The position of the spring should be horizontal when the flap is installed horizontally so that it can be opened and closed optimally. This also applies to the vertical installation.

User questions & answers

Question:	will this draft stopper work for a bathroom exhaust fan
Answer:	It certainly will work. As long as your using 4 in. Bath exhaust tubing. Directional flow of damper. You have to pay attention to direction arrow.
Question:	Are there clamps to attach this
Answer:	No you use aluminum duck tape to hold it together. I used Professional Grade Aluminum Foil Tape - 2 Inch by 210 Feet (70 Yards) - Perfect for HVAC, Sealing & Patching Hot & Cold Air Ducts.
Question:	Do I need to buy a connector for this or can I just insert it into the ducting
Answer:	I think it does.

Product description

This is a genuine replacement part. The model number and name for the following item is: Lambro DE904 Dryer Vent Elbow.

From the Manufacturer

This is a genuine replacement part. The model number and name for the following item is: Lambro DE904 Dryer Vent Elbow

• 4" diameter 90 degree aluminum duct elbow
• 4 sections riveted, each section machined together for full range adjustability, crimped at one end
• Fully adjustable aluminum elbow from 0 degrees to 90 degrees
• Light gauge, most commonly used in clothes dryer or bathroom venting
• Genuine replacement part, works with most major appliance brands
• Manufacturer model # DE904
• Genuine Replacement Part
• Whirlpool item

User questions & answers

Question:	What gauge is this
Answer:	The listing states it is .014 thickness which would be about 29 gauge. I installed it on the dryer and it worked very well and was a quarter of the price of the one offered at the depot.
Question:	Which side connects to the dryer? The crinkled side or smooth side
Answer:	The smooth side, since the dryer tube is slightly smaller in diameter
Question:	Do you have to use clamps or tape or will it hold without
Answer:	I used tape its solid so I wouldn't recommend a clamp. If you are worried about the tape you use get a ul (universal license) aluminum tape also you insurance company shouldn't have a problem as the ul tape is used on furnace ductwork which has a much high temperature rise
Question:	Just how exactly can this be "fully adjustable" as the page states please?? Thanks
Answer:	The segments swivel. You can twist each of them separately.

Product description

“Ventilation” Is The Process Of Exchanging Air In a Space In Order To Improve The Overall Air Quality. Maintaining This Air Quality Often Involves Temperature Control, Carbon Dioxide Removal, And Oxygen Replenishment.The Key To Successful Ventilation Lies With HVAC Air Ducts.

Specification

Inner:Double Aluminum Foil,Double Insulation

Frame:Bold Steel Wire Spiral,Integrated Ventilation

Outer Sleeve:Black Pvc Film,Waterproof And Lightproof

Temperature Range:-30degree-150degree

Color:Black

Size:4 Inch x 16ft

Feature:

YIJU's Flexible Aluminum Foil Duct Is Ideal For General Purpose Exhaust Applications.We Specialize In Flexible Hose For Heating,Cooling, And Venting In Outside Air To Maintain High Quality Air Control.Whether You Want To Cool a Car, House,Or Industrial Sized Building, We Have The Right Air Duct Hoses For The Task.This Ducting Suitable For Kitchens,Bathroom,Grow Tent,Green Houses And Air Conditioner Etc.

Package Include:

1 X Air Ducting

2 X Clamps

• 【FLEXIBLE 3-LAYER MATERIAL】-- Designed For Three Layer,Double Aluminum Foil Inside + Thick Black PVC Film for Lightproof,The Steel Wire Helix to Preserve The Shape,Keep Your Ventilation System Free of Rips And Pin Holes.YIJU Air Ducting Flexible Enough for You HVAC Systems,Arbitrarily Bent,No Rigid Elbow,Reducing The Ventilation Resistance And The Leak of Wind.
• 【PVC VENT HOSE】-- Black PVC Film,Lightproof and Waterproof,And Also Reducing Noise from Fans and Carbon Filter Systems.Compared to Traditional Aluminum Foil Hoses, PVC Dryer Vent Hose Are Stronger, Less Prone to Tearing and Have a Long Service Life.
• 【4 INCH 16FT AIR DUCTING】-- YIJU's Flexible Aluminum Foil Duct is Ideal for General Purpose Exhaust Applications.We Specialize in Flexible Hose for Heating, Cooling, and Venting in Outside Air to Maintain High Quality Air Control.Whether You Want to Cool a Car, House, or Industrial Sized Building, We Have The Right Air Duct Hoses for The Task.
• 【VENTILATION DUCT WIDELY USED IN】-- Ducts Are Conduits or Passages Used in Heating, Ventilation, and Air Conditioning (HVAC) to Deliver and Remove Air.Works With Fans and Carbon Filter, It Also Can Be As Ac Exhaust Hose and Dryer Vent Hose.
• 【EASY TO USE】-- YIJU Aluminum Ducting Can Be Easily Cut By Wire Cutter and Paper Knife(Caution, Risk Of Scratching Hand).This Ducting Suitable for Kitchens,Bathroom,Grow Tent,Green Houses and Air Conditioner Etc.

User questions & answers

Question:	Is the hose included in the kit
Answer:	The description for this item clearly answers your question but here goes... This item includes a 26 foot dryer vent HOSE and two clamps: one for each end.
Question:	Can this be used for collecting dust from a wood workshop? Will the wood chips or saw dust flow freely through it
Answer:	Yes I believe they would. Just an opinion since I donot use it for that purpose. The product is very durable.
Question:	My dryer sticks out more than the washer and they told I could replace the vent duct for one that I can push the dryer back more. Is this it
Answer:	This one is pretty delicate foil. I ended up with a tear after moving my dryer back. I ended up getting a more durable material.
Question:	Can be use in an electric cloth dryer
Answer:	I'm using it on my electric dryer. No problems

Product description

Dundas janine dryer vent pipe, heavy gauge, 4 in nominal, 24 in length, snap lock end, aluminum, bulk pack. This product can be used for venting most types of heating units. It works effectively and is convenient to use as well. It is definitely a great quality product.

• Designed to work effectively
• Convenient and easy to use
• Durable and long lasting

User questions & answers

Question:	inch ID or OD
Answer:	I believe 4" OD
Question:	through the wall duck
Answer:	Yes you can put it through an interior wall but get the proper end if your talking outside wall
Question:	what is the diameter
Answer:	4"
Question:	what is the diameter
Answer:	4"

• DOES THE TRICK: The Snap-to-Vent simple design gives you the power to hook up your dryer in just a matter of a few minutes. No more fiddling around with rigid metal dryer clamps!
• SAVES YOU MONEY: Our silicon seal ring gives you an airtight dryer connection, making your dryer more efficient while using less energy. This means your clothes get dryer faster and you save money on your power bill!
• AVOID THE HEADACHE: The STV-90 lets you to push your dryer up against your wall without kinking or crushing the hose and losing airflow. Simply slide it on and push your dryer back.
• WORKS WITH YOUR HOSE: We’ve updated our design to fit any 4” vent ducting, whether beveled or straight. You don’t need to go searching for the right sized clamp anymore--we’ve got you covered!
• EFFORTLESS AND DURABLE: Our sturdy elbow connector makes set up simple and a one-time project. Your STV-90 is sure to last longer than any other duct clamp out there!

User questions & answers

Question:	Do you have to use the rubber sleeve. The unit slips on and off with ease however I don't want it popping off
Answer:	I felt that without the rubber gasket it would come off. It holds really tight with the gasket. Mine did come off without it. I slid the gasket onto the dryer first then pushed the ring onto it.
Question:	Can it be turned upside down to vent through the floor
Answer:	Yes, it can be turned upside down and attach the hose to connect to dryer. As long as it is a 4" beveled duct.
Question:	Can it be be turned to the side or does it have to be straight up
Answer:	Yes, you can turn it to the side to run the hose horizontally to the floor.
Question:	Would this product work with the xtremepowerus stainless steel tumble cloths dryer compact dryer
Answer:	as long as the exhaust duct on the dryer is 4", then there shouldn't be a problem. Refer to the owner's manual for the dryer to see if there are any special considerations for the exhaust vent.

Product features

Snap to Vent 90 Degree Elbow

Best use and practices when using Snap to Vent 90 Degree Elbow:

1. Prevents crushed hoses on back of dryer
2. Fits all 4" flexible dryer hose
3. Fits on all 4" dryer duct with bevel side out both on dryer and wall
4. Seal is tacky to create a good seal between duct and connector

Snap to Vent Pieces

• Quick and easy install, snap and plug into the duct
• Preent crushed hoses and hoses from falling off the back of your dryer
• Makes dryer duct easy to cleanout for best dryer efficiency
• Patent Pending technology
• Made in USA!

Product description

HVAC Premium has been providing superior in quality service for many many years. Our products are second to none, and we've helped numerous contractors,

DIY projects, and home improvement remodeling specialists complete their masterpiece. If you are looking for a top of the line unit to enhance your project

look no further than HVAC Premium. We have the largest selection of Grilles Registers & Diffusers.

HVAC Premium has sold over 5,000,000 HVAC Components - We are proud of our many happy customers!

Our Galvanized Sheet Metal Duct Pipes are manufactured from high quality galvanized steel. The end is crimped to connect consecutive

joints or for sheet metal fittings and flexible duct. The snap on system makes for easy installation and will prevent the seam from coming apart

while also preventing air leakage making your HVAC system more energy efficient and in turn, lowering the cost of your utility bills.

Just snap the seam together and that's it!



Durable Material - 30 Gauge Thick & Made of Thick & Durable Galvanized Sheet Metal - Used For HVAC System Duct Work In Any Building or Home

Quality Packaging - Carefully Packaged in Corrugated Box To Prevent Damage In Shipment

100% Satisfaction Guaranteed - Don't worry, you're covered by our 100% money back guarantee no questions asked.

Click Add to Cart Now! and enjoy a new updated refreshing look to your home.

• 4" X 20' - Round Duct Sheet Metal Pipe - 10 PACK of 2' pipes - 30 Gauge Galvanized - Crimped End Connection
• 10 IN APACK - 4 Inch Diameter Pipe – 20 Foot Length When Connected – 30 Gauge Thick & Made of Thick & Durable Galvanized Sheet Metal - Used For HVAC System Duct Work In Any Building or Home
• HIGH QUALITY - High Quality Galvanized Sheet Metal with Crimped Ends (Snap-Lock Design) For Easy Fitting and Secure Connection To Consecutive Duct Joints
• Made of Galvanized Metal To Prevent Corrosion and Oxidation & Rust From Water & Moisture That Lasts Longer Requiring Less Maintenance – Save Money With This Energy Efficient Material Maximizes Airflow And Reduces Fire Hazards
• QUALITY PACKAGING & SATISFACTION GUARANTEED- Quality Packaging - Carefully Packaged in Corrugated Box To Prevent Damage In Shipment - Hand Inspected for Quality - 100% Satisfaction Guaranteed, Don’t worry you’re covered by our 100% money back guarantee no questions asked. Click Add to Cart now and enjoy a new updated refreshing look to your home

User questions & answers

Question:	Would this be appropriate to use in a masonry chimney to vent a woodstove? If so, would insulation around the piping also be required
Answer:	Gonna say no. They have a soft gasket that likely isn't heat rated. A badly done vent or pipe can reasonably kill people so I would get the correct part.
Question:	In what country are these duct pipes made
Answer:	They're made in the US
Question:	Can this be used for dryer venting out the roof
Answer:	This is for HVAC System Duct Work only
Question:	The ad is confusing: is the 4" X 25 feet long price $88.00 , the the information is for 5' diameter. . Is the 25 foot long item 4" or
Answer:	5 IN A PACK - 4 Inch Diameter Pipe – 25 Foot Length When Connected

Product description

Make dryer vent installation quick and easy while protecting the duct with our Easy Connecting Dryer Vent Hook Up Kit. 1 semi-rigid aluminum duct (8’ long) twists into the white polypropylene Hooker-Upper attachments, which slide into place over the dryer vent and outlet pipe. No clamps, tools or tape are needed. Some dryers require the included gasket for a proper fit. The Hooker-Upper protectors are designed to prevent the duct from being smashed behind the dryer, which helps prevent unsafe dryer operation and longer dryer times. Deflecto was founded on innovative, problem solving products. For over a half century, we have built a tradition of discovering and meeting needs with invention and dependable manufacturing. Today, Deflecto is the world’s largest chair mat, bicycle reflector and dryer venting manufacturer and a global leader in sign and literature holders, office workspace accessories and other air distribution products.

From the Manufacturer

Deflecto Hupk8wa/4 Easy Connecting Dryer Vent Hook-up Kit;

• Easy Connecting Dryer Vent Hook Up Kit includes 2 Hooker-Upper protectors, 1 semi-rigid aluminum 8’ long duct and 1 gasket
• Duct twists into Hooker-Upper protectors and slides over dryer vent and outlet pipe; No clamps, tools or tape necessary
• Hooker-Upper also protects the duct from being smashed behind dryer, which helps prevent unsafe dryer operation and longer drying times
• Kit contains 8’ long aluminum semi-rigid, flexible duct that allows quick, easy installation
• Gasket (included) may be needed for a proper fit on some dryers

User questions & answers

Question:	Is the duct hose 8 feet long
Answer:	Definitely not! The product dimensions state that it's 28 inches long, but I have a feeling that's the shipping size, and it will stretch somewhat longer than that, but NOT 8 feet!
Question:	Confused how this attaches to the dryer. Does it include connectors that stay attached to the dryer and the wall and the pipe clips in
Answer:	It includes connectors. They are simply pushed into place. They will stay if there is not too much tension on the unit. I had to duct tape mine for them to stay in place.
Question:	Is this a lot strong than the foil ones? My cat shredded 2 of those
Answer:	My cat too shredded the foil type, so I ordered this one. This cannot be shredded, its made very strong. I was unable to use this however, as the ends easily slid off in attempts to connect it to the "tubes". When it has to go from high to low connections (or low to high) its stiffness makes it hard to stay on. If the connection is pretty much vertical its easier. But like a previous comment, you will need something to secure it to each end, especially with kitties around!
Question:	Can the plastic end withstand the dryer heat? Can the flexible duct be cut to size and put the plastic end secyrely back
Answer:	Yes! The plastic end can withstand the heat. Now here comes the problem! When you try to cut the flexible duct it starts to unreaval and you cannot get it to stop when you try to work with it. I ended up just throwing it in the trash.

Product features

About Us

Deflecto’s rich heritage was founded on innovative and problem solving products. It was in 1960, in the basement of C.P. Meyer’s home, that he invented the first air deflector. His idea was to develop something that would help prevent factory compressors from freezing up. It didn’t take long to realize his new invention could have a major impact on personal home comfort as well. He knew that by deflecting air away from windows and from under furniture, heating & cooling efficiency and comfort could be maximized. Five years later, a clever Deflecto employee turned a magnetic air deflector upside down on a metal filing cabinet in effort to organize invoices. With that, the first wall pocket was discovered, opening up the office products market for C.P. Meyer and his company.

Product description

VENT SYSTEMS is a company with a long tradition and experience. We provide innovative solutions in the field of ventilation of premises. We are constantly striving to develop and deliver even better, more advanced and more efficient technologies that would enable our customers to enjoy healthy fresh air indoors. All products undergo thorough quality control before going on sale. We also guarantee professional service and periodic maintenance system for maintaining system reliability for many years. We have created the value of the VENT SYSTEMS brand by putting particular emphasis on: HIGH QUALITY OF THE PRODUCT - WIDE RANGE OF PRODUCTS - MEETING THE CUSTOMER'S NEEDS.

• The duct connector is a three-hole - 3 way connector with two branches. With the dryer vent hose it can be connected to exhaust fans, dryer vent covers and vent seals.
• It can be used outdoors and indoors, even if it is exposed to the sun and rain.
• The interior of the duct splitter is smooth, and its reasonable curvature greatly reduces the wind resistance. At the same time, it can discharge air from each part in the ventilation project.
• The dryer duct connector is seamlessly connected to achieve a good leakproof effect. Don't worry about leaking air after installation. It is small in size, so it doesn't take up space.
• It is suitable for hoses of 100 mm (4 Inch). Wipe the tee when using it, then dock it with the hose and fix it with aluminum foil tape. Finally, install the clamp and tighten the screw.

• QUICK AND EASY INSTALLATION – The use of this dryer hose vent snap on kit is so easy and it requires no tools. It can be put together within minutes with just your own two hands. The simplicity of this snap on hose kit is that it allows you to begin using the dryer right away. Just pre-assemble the 90 elbow, 4" hose, and straight piece. Attach it to the dryer and the wall and it’s all set for use.
• THE BETTER CHOICE – This snap on dryer hose from ZIGGURAT provides a top-quality product for anyone in need of dryer connections. Our dryer connectors resolve the risk of potential fires, help create a better operating dryer, and don’t need to be attached by a clamp. These products are the best choice for simplicity and durability. This complete kit installs easily and works efficiently.
• BUILT TO LAST – Our STV-M snap to vent kit is designed to last a long time. With strong, yet flexible materials we have found the perfect way to create a clothes dryer connector that will get the job done for many years to come. ZIGGURAT’s dryer hose connector kit is made to be easily cleaned out and is made of quality materials to prevent crushing, ripping or other possible damage to the connection.
• TIGHT ATTACHMENT– This plastic dryer hose kit is made with soft rubber that will snugly attach to the hose you’re your dryer. The flexibility of this connector for dryer allows the pieces to fit properly together as well as hug the wall once the appliance is pushed against it. This kit is 8 x 4 x 5 inches and gives a strong connection without creating a bulky mess behind your clothes dryer.
• PRODUCTS MADE IN THE USA – The ZIGGURAT products were envisioned by a father and son who cared about safety and value. Our safe alternatives to dryer duct connectors were designed to improve household safety. We rely on quality to sell our products. All of our products are made in the USA with top-quality materials. We create household accessories that make life easier for our valued customers.

User questions & answers

Question:	At the wall end, will this fit over the aldes 4 inch round spring loaded backdraft damper
Answer:	I don’t know for sure. My problem was after researching I found plastic will melt under those circumstances and are not recommended on dryers. The thin , flexible ones are not recommended either. Because of a short space the plumber cut from a formed duct to make it work. Much safer and won’t break like the previous one did.
Question:	I require a solution of the vent hose to the outside. My outtake vent-hole is glass block, also 4 inch. I want a secure connection, tight-fitting
Answer:	Connection to our vent attached to a metal connection. A rubber band is placed around the metal piece and when the piece slips on it grabs the rubber and stays on. Don't know if it would work in your case but there is a YouTube video that show it.
Question:	Once installed, can the ends be disconnected periodically, like once a year, to clean out lint? If so, do I need new rubber seals each time
Answer:	Absolutely, you can just pull it off the duct and clean out the hose and your ducting and put it back on with the same seal. The seal should stay on the duct and be just fine to reuse.
Question:	Is the hose included in the kit
Answer:	Yes, the kit came with a hose.

Product description

For home improvement, connect your gas or electric dryer to the exhaust vent with this fire-resistant, semi-rigid flexible aluminum duct. 4” diameter by 24” long, with male and female connectors. Durable construction won’t get mashed or bent out of shape during handling and installation, and will hold the shape you give it without sagging. Permanently attached rotating collar on the female end make connection and rotation a snap, and maintains an airtight seal while in use. Deflecto was founded on innovative, problem solving products. For over a half century, we have built a tradition of discovering and meeting needs with invention and dependable manufacturing. Today, Deflecto is the world’s largest chair mat, bicycle reflector and dryer venting manufacturer and a global leader in sign and literature holders, office workspace accessories and other air distribution products.

• Semi rigid aluminum duct has a 4” diameter and 24” length
• Flexible enough for ease of installation, and holds the shape you put it in without sagging
• Fire-resistant aluminum construction is perfect for gas and electric dryer applications
• Permanently attached female collar and crimped male end for ease of connection, rotation, and consistent airtight use
• Durable material holds up during handling and installation

User questions & answers

Question:	What length can the duct be compressed to
Answer:	Manufacturer Deflect-o Products Part Number MAC36024/6 Item Weight 4.8 ounces Product Dimensions 9.38 x 4.75 x 9.94 inches So, after you take them out of the box the compressed length of the ducts is a little bit under 9.94 inches
Question:	Is it a three piece
Answer:	The product is one piece. The picture illustrates the various ways it can be flexed for your application.

Product features

Deflecto Semi Rigid Aluminum Duct with Attached Connectors, Silver

Semi-rigid duct with integrated male and female connectors, Easy to install without clamps, tools or tape. Integrated connectors help prevent crushing. Extends up to 24". Use for kitchen or bathroom venting and forced air distribution.

• Easily connects without the use of clamps, tools or tape
• Extends up to 24"
• Fire-resistant
• Integrated connectors help prevent crushing of duct to ensure a secure connection